# # 8390 device configuration # config NET_VENDOR_8390 bool "National Semi-conductor 8390 devices" default y depends on NET_VENDOR_NATSEMI && (AMIGA_PCMCIA || PCI || SUPERH || \ ISA || EISA || MAC || M32R || MACH_TX49XX || \ H8300 || ARM || MIPS || ZORRO || PCMCIA || \ EXPERIMENTAL) ---help--- If you have a network (Ethernet) card belonging to this class, say Y and read the Ethernet-HOWTO, available from . Note that the answer to this question doesn't directly affect the kernel: saying N will just cause the configurator to skip all the questions about Western Digital cards. If you say Y, you will be asked for your specific card in the following questions. if NET_VENDOR_8390 config EL2 tristate "3c503 \"EtherLink II\" support" depends on ISA select CRC32 ---help--- If you have a network (Ethernet) card of this type, say Y and read the Ethernet-HOWTO, available from . To compile this driver as a module, choose M here. The module will be called 3c503. config AC3200 tristate "Ansel Communications EISA 3200 support (EXPERIMENTAL)" depends on PCI && (ISA || EISA) && EXPERIMENTAL select CRC32 ---help--- If you have a network (Ethernet) card of this type, say Y and read the Ethernet-HOWTO, available from . To compile this driver as a module, choose M here. The module will be called ac3200. config PCMCIA_AXNET tristate "Asix AX88190 PCMCIA support" depends on PCMCIA ---help--- Say Y here if you intend to attach an Asix AX88190-based PCMCIA (PC-card) Fast Ethernet card to your computer. These cards are nearly NE2000 compatible but need a separate driver due to a few misfeatures. To compile this driver as a module, choose M here: the module will be called axnet_cs. If unsure, say N. config AX88796 tristate "ASIX AX88796 NE2000 clone support" depends on (ARM || MIPS || SUPERH) select CRC32 select PHYLIB select MDIO_BITBANG ---help--- AX88796 driver, using platform bus to provide chip detection and resources config AX88796_93CX6 bool "ASIX AX88796 external 93CX6 eeprom support" depends on AX88796 select EEPROM_93CX6 ---help--- Select this if your platform comes with an external 93CX6 eeprom. config E2100 tristate "Cabletron E21xx support" depends on ISA select CRC32 ---help--- If you have a network (Ethernet) card of this type, say Y and read the Ethernet-HOWTO, available from . To compile this driver as a module, choose M here. The module will be called e2100. config ES3210 tristate "Racal-Interlan EISA ES3210 support (EXPERIMENTAL)" depends on PCI && EISA && EXPERIMENTAL select CRC32 ---help--- If you have a network (Ethernet) card of this type, say Y and read the Ethernet-HOWTO, available from . To compile this driver as a module, choose M here. The module will be called es3210. config HPLAN_PLUS tristate "HP PCLAN+ (27247B and 27252A) support" depends on ISA select CRC32 ---help--- If you have a network (Ethernet) card of this type, say Y and read the Ethernet-HOWTO, available from . To compile this driver as a module, choose M here. The module will be called hp-plus. config HPLAN tristate "HP PCLAN (27245 and other 27xxx series) support" depends on ISA select CRC32 ---help--- If you have a network (Ethernet) card of this type, say Y and read the Ethernet-HOWTO, available from . To compile this driver as a module, choose M here. The module will be called hp. config HYDRA tristate "Hydra support" depends on ZORRO select CRC32 ---help--- If you have a Hydra Ethernet adapter, say Y. Otherwise, say N. To compile this driver as a module, choose M here: the module will be called hydra. config ARM_ETHERH tristate "I-cubed EtherH/ANT EtherM support" depends on ARM && ARCH_ACORN select CRC32 ---help--- If you have an Acorn system with one of these network cards, you should say Y to this option if you wish to use it with Linux. config LNE390 tristate "Mylex EISA LNE390A/B support (EXPERIMENTAL)" depends on PCI && EISA && EXPERIMENTAL select CRC32 ---help--- If you have a network (Ethernet) card of this type, say Y and read the Ethernet-HOWTO, available from . To compile this driver as a module, choose M here. The module will be called lne390. config MAC8390 bool "Macintosh NS 8390 based ethernet cards" depends on MAC select CRC32 ---help--- If you want to include a driver to support Nubus or LC-PDS Ethernet cards using an NS8390 chipset or its equivalent, say Y and read the Ethernet-HOWTO, available from . config MCF8390 tristate "ColdFire NS8390 based Ethernet support" depends on COLDFIRE select CRC32 ---help--- This driver is for Ethernet devices using an NS8390-compatible chipset on many common ColdFire CPU based boards. Many of the older Freescale dev boards use this, and some other common boards like some SnapGear routers do as well. If you have one of these boards and want to use the network interface on them then choose Y. To compile this driver as a module, choose M here, the module will be called mcf8390. config NE2000 tristate "NE2000/NE1000 support" depends on (ISA || (Q40 && m) || M32R || MACH_TX49XX) select CRC32 ---help--- If you have a network (Ethernet) card of this type, say Y and read the Ethernet-HOWTO, available from . Many Ethernet cards without a specific driver are compatible with NE2000. If you have a PCI NE2000 card however, say N here and Y to "PCI NE2000 and clone support" under "EISA, VLB, PCI and on board controllers" below. To compile this driver as a module, choose M here. The module will be called ne. config NE2K_PCI tristate "PCI NE2000 and clones support (see help)" depends on PCI select CRC32 ---help--- This driver is for NE2000 compatible PCI cards. It will not work with ISA NE2000 cards (they have their own driver, "NE2000/NE1000 support" below). If you have a PCI NE2000 network (Ethernet) card, say Y and read the Ethernet-HOWTO, available from . This driver also works for the following NE2000 clone cards: RealTek RTL-8029 Winbond 89C940 Compex RL2000 KTI ET32P2 NetVin NV5000SC Via 86C926 SureCom NE34 Winbond Holtek HT80232 Holtek HT80229 To compile this driver as a module, choose M here. The module will be called ne2k-pci. config APNE tristate "PCMCIA NE2000 support" depends on AMIGA_PCMCIA select CRC32 ---help--- If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise, say N. To compile this driver as a module, choose M here: the module will be called apne. config NE3210 tristate "Novell/Eagle/Microdyne NE3210 EISA support (EXPERIMENTAL)" depends on PCI && EISA && EXPERIMENTAL select CRC32 ---help--- If you have a network (Ethernet) card of this type, say Y and read the Ethernet-HOWTO, available from . Note that this driver will NOT WORK for NE3200 cards as they are completely different. To compile this driver as a module, choose M here. The module will be called ne3210. config PCMCIA_PCNET tristate "NE2000 compatible PCMCIA support" depends on PCMCIA select CRC32 ---help--- Say Y here if you intend to attach an NE2000 compatible PCMCIA (PC-card) Ethernet or Fast Ethernet card to your computer. To compile this driver as a module, choose M here: the module will be called pcnet_cs. If unsure, say N. config NE_H8300 tristate "NE2000 compatible support for H8/300" depends on H8300 ---help--- Say Y here if you want to use the NE2000 compatible controller on the Renesas H8/300 processor. config STNIC tristate "National DP83902AV support" depends on SUPERH select CRC32 ---help--- Support for cards based on the National Semiconductor DP83902AV ST-NIC Serial Network Interface Controller for Twisted Pair. This is a 10Mbit/sec Ethernet controller. Product overview and specs at . If unsure, say N. config ULTRA tristate "SMC Ultra support" depends on ISA select CRC32 ---help--- If you have a network (Ethernet) card of this type, say Y and read the Ethernet-HOWTO, available from . Important: There have been many reports that, with some motherboards mixing an SMC Ultra and an Adaptec AHA154x SCSI card (or compatible, such as some BusLogic models) causes corruption problems with many operating systems. The Linux smc-ultra driver has a work-around for this but keep it in mind if you have such a SCSI card and have problems. To compile this driver as a module, choose M here. The module will be called smc-ultra. config ULTRA32 tristate "SMC Ultra32 EISA support" depends on EISA select CRC32 ---help--- If you have a network (Ethernet) card of this type, say Y and read the Ethernet-HOWTO, available from . To compile this driver as a module, choose M here. The module will be called smc-ultra32. config WD80x3 tristate "WD80*3 support" depends on ISA select CRC32 ---help--- If you have a network (Ethernet) card of this type, say Y and read the Ethernet-HOWTO, available from . To compile this driver as a module, choose M here. The module will be called wd. config ZORRO8390 tristate "Zorro NS8390-based Ethernet support" depends on ZORRO select CRC32 ---help--- This driver is for Zorro Ethernet cards using an NS8390-compatible chipset, like the Village Tronic Ariadne II and the Individual Computers X-Surf Ethernet cards. If you have such a card, say Y. Otherwise, say N. To compile this driver as a module, choose M here: the module will be called zorro8390. endif # NET_VENDOR_8390