The Freescale DIU video controller supports five video "modes", but only
the first two are used by the driver.  The other three are special modes
that don't make sense for a framebuffer driver.  Therefore, there's no
point in keeping a global variable that indicates which mode we're
supposed to use.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NFlorian Tobias Schandinat <FlorianSchandinat@gmx.de>

Move several macros and structures from the Freescale DIU driver's header
file into the source file, because they're only used by that file.  Also
delete a few unused macros.

The diu and diu_ad structures cannot be moved because they're being used
by the MPC5121 platform file.  A future patch eliminate the need for
the platform file to access these structs, so they'll be moved also.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NFlorian Tobias Schandinat <FlorianSchandinat@gmx.de>

Use the _IOx macros to define the ioctl commands, instead of hard-coded
numbers.  Unfortunately, the original definitions of MFB_SET_PIXFMT and
MFB_GET_PIXFMT used the wrong value for the size, so these macros have
new values now.  To avoid breaking binary compatibility with older
applications, we retain support for the original values, but the driver
displays a warning message if they're used.

Also remove the FBIOGET_GWINFO and FBIOPUT_GWINFO ioctls.  FBIOPUT_GWINFO
was never implemented, and FBIOGET_GWINFO was never used by any
application.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NFlorian Tobias Schandinat <FlorianSchandinat@gmx.de>

Add the ability to disable PCI-E MPS turning and using the BIOS
configured MPS defaults.  Due to the number of issues recently
discovered on some x86 chipsets, make this the default behavior.

Also, add the option for peer to peer DMA MPS configuration.  Peer to
peer DMA is outside the scope of this patch, but MPS configuration could
prevent it from working by having the MPS on one root port different
than the MPS on another.  To work around this, simply make the system
wide MPS the smallest possible value (128B).
Signed-off-by: NJon Mason <mason@myri.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add zorder support on OMAP4, this feature allows deciding the visibility order
of the overlays based on the zorder value provided as an overlay info parameter
or a sysfs attribute of the overlay object.

Use the overlay cap OMAP_DSS_OVL_CAP_ZORDER to determine whether zorder is
supported for the overlay or not. Use dss feature FEAT_ALPHA_FREE_ZORDER
if the caps are not available.

Ensure that all overlays that are enabled and connected to the same manager
have different zorders. Swapping zorders of 2 enabled overlays currently
requires disabling one of the overlays.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add support for VIDEO3 pipeline on OMAP4:
- Add VIDEO3 pipeline information in dss_features and omapdss.h
- Add VIDEO3 pipeline register coefficients in dispc.h
- Create a new overlay structure corresponding to VIDEO3.
- Make changes in dispc.c for VIDEO3
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

On OMAP3, in order to enable alpha blending for LCD and TV managers, we needed
to set LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits in DISPC_CONFIG. On
OMAP4, alpha blending is always enabled by default, if the above bits are set,
we switch to an OMAP3 compatibility mode where the zorder values in the pipeline
attribute registers are ignored and a fixed priority is configured.

Rename the manager_info member "alpha_enabled" to "partial_alpha_enabled" for
more clarity. Introduce two dss_features FEAT_ALPHA_FIXED_ZORDER and
FEAT_ALPHA_FREE_ZORDER which represent OMAP3-alpha compatibility mode and OMAP4
alpha mode respectively. Introduce an overlay cap for ZORDER. The DSS2 user is
expected to check for the ZORDER cap, if an overlay doesn't have this cap, the
user is expected to set the parameter partial_alpha_enabled. If the overlay has
ZORDER cap, the DSS2 user can assume that alpha blending is already enabled.

Don't support OMAP3 compatibility mode for now. Trying to read/write to
alpha_blending_enabled sysfs attribute issues a warning for OMAP4 and does not
set the LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits.

Change alpha_enabled to partial_alpha_enabled in the omap_vout driver. Use
overlay cap "OMAP_DSS_OVL_CAP_GLOBAL_ALPHA" to check if overlay supports alpha
blending or not. Replace this with checks for VIDEO1 pipeline.

Cc: linux-media@vger.kernel.org
Cc: Lajos Molnar <molnar@ti.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
Acked-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

overlay_info struct, used to configure overlays, currently includes both
physical and virtual addresses for the pixels. The vaddr was added to
support more exotic configurations where CPU would be used to update a
display, but it is not currently used and there has been no interest in
the feature. Using CPU to update a screen is also less interesting now
that OMAP4 has two LCD outputs.

This patch removes the vaddr field, and modifies the users of omapdss
accordingly. This makes the use of omapdss a bit simpler, as the user
doesn't need to think if it needs to give the vaddr.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This is a driver for N800's display, ported from the old omapfb. This is
a slightly lighter version of the driver as not all features of the old
driver can be ported without big changes to DSS2, and also because some
of the HW features used in the old driver are unclear (e.g. the power
management part).

That said, the new driver works fine for basic use.

Architecturally the driver is not as neat as it could be. N800's display
HW consists of a display buffer chip and a panel, and ideally they would
be represented by separate, independent drivers. This is not currently
possible, and this driver contains both buffer chip and panel driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Taal panel driver supports two kinds of backlight control: 1) using DSI
commands sent to the panel to control the backlight, 2) calling function
pointers going to the board file to control the backlight.

The second option is a bit hacky, and will no longer be needed when the
PWM driver supports the backlight features. After that we can use the
standard PWM backlight driver.

This patch removes the second backlight control mechanism, and adds a
boolean field, use_dsi_backlight, to nokia_dsi_panel_data which the
board file can use to inform whether the panel driver should use DSI
commands to control the backlight.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We have currently panel-generic-dpi driver, which is a combined driver
for dummy panels and also for DVI output.

The aim is to split the panel-generic-dpi into two, one for fixed size
dummy panels connected via DPI, and the other (this) for variable
resolution output which supports DDC channel (in practice a DVI framer
chip connected to DPI output).

Original i2c code by: Ricardo Salveti de Araujo
<ricardo.salveti@canonical.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

detect() can be used to probe if the display is connected.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

read_edid() can be used to get the EDID information from the display.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add IRQ definitions for missing OMAP4 IRQs: FRAMEDONEWB, FRAMEDONETV,
WBBUFFEROVERFLOW.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

regn divider is one greater than the REGN divider in TRM. Add a comment
to point this out.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

regn divider is currently programmed to the registers without change,
but when calculating clock frequencies it is used as regn+1.

To make this similar to how DSI handles the dividers this patch changes
the regn value to be used as such for calculations, but the value
programmed to registers is regn-1.

This simplifies the clock frequency calculations, makes it similar to
DSI, and also allows us to use regn value 0 as undefined.

Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add initial support for DSI video mode panels:
- Add a new structure omap_dss_dsi_videomode_data in the member "panel" in
  omap_dss_device struct. This allows panel driver to configure dsi video_mode
  specific parameters.
- Configure basic DSI video mode timing parameters: HBP, HFP, HSA, VBP, VFP, VSA,
  TL and VACT.
- Configure DSI protocol engine registers for video_mode support.
- Introduce functions dsi_video_mode_enable() and dsi_video_mode_disable() which
  enable/disable video mode for a given virtual channel and a given pixel format
  type.

Things left for later
- Add functions to check for errors in video mode timings provided by panel.
- Configure timing registers required  for command mode interleaving.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Currently, DSI pixel info is only represented by the pixel size in bits using
the pixel_size parameter in omap_dss_device struct's ctrl member.

This is not sufficient information for DSI video mode usage, as two of the
supported formats(RGB666 loosely packed, and RGB888) have the same pixel
container size, but different data_type values for the video mode packet header.

Create enum "omap_dss_dsi_pixel_format" which describes the pixel data format
the panel is configured for. Create helper function dsi_get_pixel_size() which
returns the pixel size of the given pixel format.

Modify functions omapdss_default_get_recommended_bpp() and dss_use_replication()
to use dsi_get_pixel_size().
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Introduce read functions which use generic Processor-to-Peripheral
transaction types. These are needed by some devices which may not support
corresponding DCS commands.

Add function dsi_vc_generic_send_read_request() which can send
a short packet with 0, 1 or 2 bytes of request data and the corresponding
generic data type.

Rename function dsi_vc_dcs_read_rx_fifo() to dsi_vc_read_rx_fifo() and modify
it to take the enum "dss_dsi_content_type" as an argument to use either DCS
or GENERIC Peripheral-to-Processor transaction types while parsing data read
from the device.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Remove functions dsi_vc_dcs_read_1() and dsi_vc_dcs_read_2(), these are used
when the panel is expected to return 1 and 2 bytes respecitvely. This was manily
used for debugging purposes. These functions should be implemented in the panel
driver if needed.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Intoduce enum "dss_dsi_content_type" to differentiate between DCS and generic
content types.

Introduce short and long packet write functions which use generic
Processor-to-Peripheral transaction types. These are needed by some devices
which may not support corresponding DCS commands. Create common write functions
which allow code reuse between DCS and generic write functions.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Create an enum for DSI operation modes, use this to set the capabilities of the
device in dsi_init_display().
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add OMAP_DSS_OVL_CAP_GLOBAL_ALPHA and OMAP_DSS_OVL_CAP_PRE_MULT_ALPHA to
overlay capabilities. Use these instead of FEAT_GLOBAL_ALPHA,
FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA in code.

Remove FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA which are no
longer used. FEAT_GLOBAL_ALPHA is still used to decide if the HW has
global alpha register.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NArchit Taneja <archit@ti.com>

Remove support for non-DISPC overlays and overlay managers.

The support to possibly have non-DISPC overlays and managers was made to
make it possible to use CPU and/or sDMA to update RFBI or DSI command
mode displays. It is ok to remove the support, because:

- No one has used the feature.
- Display update without DISPC is very slow, so it is debatable if the
  update would even be usable.
- Removal cleans up code.
- If such a feature is needed later, it is better implemented outside
  omapdss driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NArchit Taneja <archit@ti.com>

Currently when changing the manager of an overlay, set_manager() directly
calls dispc to set the overlay's destination.

Change this to be more in line with other overlay configurations, and
this will also remove the need to have dispc clocks enabled when calling
set_manager().

A new field is added to overlay struct, "manager_changed". This is
similar to "display_changed" field in manager struct, and is used to
inform apply that the manager has changed and thus write to the
registers is needed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

dsi_mux_pads() needs to know about the DSI HW module and the DSI lanes
used. Split the function into two, enable and disable, which take
necessary arguments, and add empty implementations for both.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

David reported:

  Attached below is a watered-down version of rt/tst-cpuclock2.c from
  GLIBC.  Just build it with "gcc -o test test.c -lpthread -lrt" or
  similar.

  Run it several times, and you will see cases where the main thread
  will measure a process clock difference before and after the nanosleep
  which is smaller than the cpu-burner thread's individual thread clock
  difference.  This doesn't make any sense since the cpu-burner thread
  is part of the top-level process's thread group.

  I've reproduced this on both x86-64 and sparc64 (using both 32-bit and
  64-bit binaries).

  For example:

  [davem@boricha build-x86_64-linux]$ ./test
  process: before(0.001221967) after(0.498624371) diff(497402404)
  thread:  before(0.000081692) after(0.498316431) diff(498234739)
  self:    before(0.001223521) after(0.001240219) diff(16698)
  [davem@boricha build-x86_64-linux]$ 

  The diff of 'process' should always be >= the diff of 'thread'.

  I make sure to wrap the 'thread' clock measurements the most tightly
  around the nanosleep() call, and that the 'process' clock measurements
  are the outer-most ones.

  ---
  #include <unistd.h>
  #include <stdio.h>
  #include <stdlib.h>
  #include <time.h>
  #include <fcntl.h>
  #include <string.h>
  #include <errno.h>
  #include <pthread.h>

  static pthread_barrier_t barrier;

  static void *chew_cpu(void *arg)
  {
	  pthread_barrier_wait(&barrier);
	  while (1)
		  __asm__ __volatile__("" : : : "memory");
	  return NULL;
  }

  int main(void)
  {
	  clockid_t process_clock, my_thread_clock, th_clock;
	  struct timespec process_before, process_after;
	  struct timespec me_before, me_after;
	  struct timespec th_before, th_after;
	  struct timespec sleeptime;
	  unsigned long diff;
	  pthread_t th;
	  int err;

	  err = clock_getcpuclockid(0, &process_clock);
	  if (err)
		  return 1;

	  err = pthread_getcpuclockid(pthread_self(), &my_thread_clock);
	  if (err)
		  return 1;

	  pthread_barrier_init(&barrier, NULL, 2);
	  err = pthread_create(&th, NULL, chew_cpu, NULL);
	  if (err)
		  return 1;

	  err = pthread_getcpuclockid(th, &th_clock);
	  if (err)
		  return 1;

	  pthread_barrier_wait(&barrier);

	  err = clock_gettime(process_clock, &process_before);
	  if (err)
		  return 1;

	  err = clock_gettime(my_thread_clock, &me_before);
	  if (err)
		  return 1;

	  err = clock_gettime(th_clock, &th_before);
	  if (err)
		  return 1;

	  sleeptime.tv_sec = 0;
	  sleeptime.tv_nsec = 500000000;
	  nanosleep(&sleeptime, NULL);

	  err = clock_gettime(th_clock, &th_after);
	  if (err)
		  return 1;

	  err = clock_gettime(my_thread_clock, &me_after);
	  if (err)
		  return 1;

	  err = clock_gettime(process_clock, &process_after);
	  if (err)
		  return 1;

	  diff = process_after.tv_nsec - process_before.tv_nsec;
	  printf("process: before(%lu.%.9lu) after(%lu.%.9lu) diff(%lu)\n",
		 process_before.tv_sec, process_before.tv_nsec,
		 process_after.tv_sec, process_after.tv_nsec, diff);
	  diff = th_after.tv_nsec - th_before.tv_nsec;
	  printf("thread:  before(%lu.%.9lu) after(%lu.%.9lu) diff(%lu)\n",
		 th_before.tv_sec, th_before.tv_nsec,
		 th_after.tv_sec, th_after.tv_nsec, diff);
	  diff = me_after.tv_nsec - me_before.tv_nsec;
	  printf("self:    before(%lu.%.9lu) after(%lu.%.9lu) diff(%lu)\n",
		 me_before.tv_sec, me_before.tv_nsec,
		 me_after.tv_sec, me_after.tv_nsec, diff);

	  return 0;
  }

This is due to us using p->se.sum_exec_runtime in
thread_group_cputime() where we iterate the thread group and sum all
data. This does not take time since the last schedule operation (tick
or otherwise) into account. We can cure this by using
task_sched_runtime() at the cost of having to take locks.

This also means we can (and must) do away with
thread_group_sched_runtime() since the modified thread_group_cputime()
is now more accurate and would deadlock when called from
thread_group_sched_runtime().

Aside of that it makes the function safe on 32 bit systems. The old
code added t->se.sum_exec_runtime unprotected. sum_exec_runtime is a
64bit value and could be changed on another cpu at the same time.
Reported-by: NDavid Miller <davem@davemloft.net>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: stable@kernel.org
Link: http://lkml.kernel.org/r/1314874459.7945.22.camel@twinsTested-by: NDavid Miller <davem@davemloft.net>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The IEEE 1588 standard defines two kinds of messages, event and general
messages. Event messages require time stamping, and general do not. When
using UDP transport, two separate ports are used for the two message
types.

The BPF designed to recognize event messages incorrectly classifies L2
general messages as event messages. This commit fixes the issue by
extending the filter to check the message type field for L2 PTP packets.
Event messages are be distinguished from general messages by testing
the "general" bit.
Signed-off-by: NRichard Cochran <richard.cochran@omicron.at>
Cc: <stable@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

That flag no longer makes sense, since we don't look up automount points
as eagerly any more.  Additionally, it turns out that the NO_AUTOMOUNT
handling was buggy to begin with: it would avoid automounting even for
cases where we really *needed* to do the automount handling, and could
return ENOENT for autofs entries that hadn't been instantiated yet.

With our new non-eager automount semantics, one discussion has been
about adding a AT_AUTOMOUNT flag to vfs_fstatat (and thus the
newfstatat() and fstatat64() system calls), but it's probably not worth
it: you can always force at least directory automounting by simply
adding the final '/' to the filename, which works for *all* of the stat
family system calls, old and new.

So AT_NO_AUTOMOUNT (and thus LOOKUP_NO_AUTOMOUNT) really were just a
result of our bad default behavior.
Acked-by: NIan Kent <raven@themaw.net>
Acked-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since we've now turned around and made LOOKUP_FOLLOW *not* force an
automount, we want to add the ability to force an automount event on
lookup even if we don't happen to have one of the other flags that force
it implicitly (LOOKUP_OPEN, LOOKUP_DIRECTORY, LOOKUP_PARENT..)

Most cases will never want to use this, since you'd normally want to
delay automounting as long as possible, which usually implies
LOOKUP_OPEN (when we open a file or directory, we really cannot avoid
the automount any more).

But Trond argued sufficiently forcefully that at a minimum bind mounting
a file and quotactl will want to force the automount lookup.  Some other
cases (like nfs_follow_remote_path()) could use it too, although
LOOKUP_DIRECTORY would work there as well.

This commit just adds the flag and logic, no users yet, though.  It also
doesn't actually touch the LOOKUP_NO_AUTOMOUNT flag that is related, and
was made irrelevant by the same change that made us not follow on
LOOKUP_FOLLOW.

Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

598841ca ([S390] use gmap address
spaces for kvm guest images) changed kvm on s390 to use a separate
address space for kvm guests. We can now put KVM guests anywhere
in the user address mode with a size up to 8PB - as long as the
memory is 1MB-aligned. This change was done without KVM extension
capability bit.
The change was added after 3.0, but we still have a chance to add
a feature bit before 3.1 (keeping the releases in a sane state).
We use number 71 to avoid collisions with other pending kvm patches
as requested by Alexander Graf.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Acked-by: NAvi Kivity <avi@redhat.com>
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

irq_domain_simple_ops is exported, but is not declared in irqdomain.h,
so add it.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: marc.zyngier@arm.com
Cc: thomas.abraham@linaro.org
Cc: jamie@jamieiles.com
Cc: b-cousson@ti.com
Cc: shawn.guo@linaro.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree-discuss@lists.ozlabs.org
Link: http://lkml.kernel.org/r/1316017900-19918-2-git-send-email-robherring2@gmail.comSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

commit 946cedcc (tcp: Change possible SYN flooding messages)
added a build error if CONFIG_SYN_COOKIES=n
Reported-by: NMarkus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If there was ever any code that used MEM_ALLOC_THRESHOLD, it was removed a
long time ago.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NFlorian Tobias Schandinat <FlorianSchandinat@gmx.de>

The video buffer is not uncached memory-mapped I/O, so don't tag the virtual
address as __iomem.  It's also not a u8*.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NFlorian Tobias Schandinat <FlorianSchandinat@gmx.de>

Remove some unused ioctl commands, and treat those commands as unsupported
instead of ignored.

Also remove struct mfb_alpha, which isn't used by any ioctl.  It may have
been once intended for MFB_SET_ALPHA, but that ioctl uses a different
data structure.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NFlorian Tobias Schandinat <FlorianSchandinat@gmx.de>

With the conversion of struct flowi to a union of AF-specific structs, some
operations on the flow cache need to account for the exact size of the key.
Signed-off-by: NDavid Ward <david.ward@ll.mit.edu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

AF-specific flowi structs are now passed to flow_key_compare, which must
also be aligned to a long.
Signed-off-by: NDavid Ward <david.ward@ll.mit.edu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Attempt to reduce the number of IP packets emitted in response to single
SCTP packet (2e3216cd) introduced a complication - if a packet contains
two COOKIE_ECHO chunks and nothing else then SCTP state machine corks the
socket while processing first COOKIE_ECHO and then loses the association
and forgets to uncork the socket. To deal with the issue add new SCTP
command which can be used to set association explictly. Use this new
command when processing second COOKIE_ECHO chunk to restore the context
for SCTP state machine.
Signed-off-by: NMax Matveev <makc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_forward_skb loops an skb back into host networking
stack which might hang on the memory indefinitely.
In particular, this can happen in macvtap in bridged mode.
Copy the userspace fragments to avoid blocking the
sender in that case.

As this patch makes skb_copy_ubufs extern now,
I also added some documentation and made it clear
the SKBTX_DEV_ZEROCOPY flag automatically instead
of doing it in all callers. This can be made into a separate
patch if people feel it's worth it.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>