When sending the SCD_QUEUE_CONFIG command, the queue is
associated to a specific TID. If later there is a need to
use this TID on a different queue instead, it first needs to
be unassociated from the first queue.

Keep track for every queue what TID is associated with it.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When a shared queue becomes unshared, aggregations should be
re-enabled if they've existed before. Make sure that they do
this, if required.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For a000 devices there is a support of 64 bit DMA addressing.
The paging command was changed accordingly - support it.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add support for installing and removing GMAC key
for newer FW versions that support GCM and MFP.
GMAC provides authentication and integrity for multicast management
frames.

Firmware API was changed, update the driver accordingly.
Signed-off-by: NAyala Beker <ayala.beker@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The 9000 hardware will de-aggregate AMSDUs. In the process
it will copy the mac header "as is" to the new MPDUs.
This means driver should allow the same PN for MPDUs originated
from the same AMSDU.
Do that by incrementing the PN only for the last MPDU in the
sequence.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add the following to support beacon report radio measurement
with the measurement mode field set to passive or active:
1. Propagate the required scan duration to the device
2. Report the scan start time (in terms of TSF)
3. Report each BSS's detection time (also in terms of TSF)

TSF times refer to the BSS that the interface that requested the
scan is connected to.
Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com>
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
[changed ath9k/10k, at76c59x-usb, iwlegacy, wl1251 and wlcore to match
the new API]
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add support for the v4 version of the TX power command.  Just add a
new version and do the same sizing tricks that were done when support
for v3 was introduced.

This patch doesn't support the new functionality introduced, but makes
the driver work with the new size of the command.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The PCIe transport needs to store two pointers in each TX SKB, and
currently assumes mac80211's ieee80211_tx_info is present in the CB
to do that.

In order to remove that assumption, have the opmodes pass in the
offset to where the pointers can be stored in the CB and use the
offset in the PCIe code.

To make the disentanglement complete, remove mac80211.h includes
from everywhere in the generic iwlwifi code. This required adding
an include of cfg80211.h in one place.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In order to reduce reliance on mac80211 structs in the core
iwlwifi code, store the cipher schemes in the format given
by the firmware and convert it later, rather than storing it
in the mac80211 format.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Restart flow zeroes the rx_ba_sessions counter. Mac80211 asks
driver to tear down of the session only afterwards, and as a
result driver didn't free the data. Fix it.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Fixes: 10b2b201 ("iwlwifi: mvm: add infrastructure for tracking BA session in driver")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add some prints to track BAID assignment.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Make sure that in DQA mode, the SCD's configuration of a
queue is redirected to the lower AC of the streams of the
queue.

Make sure that this queue is redirected to the lowest AC
when adding a new RA/TID to an existing queue. If it isn't -
redirect the queue.

Also, as redirection revealed a bug in the marking of a
shared queue, this patch contains a small fix to make
sure a shared queue maintains the appropriate "shared queue
marking".
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support TDLS when working in DQA mode.

This is done mainly by NOT doing any special things
for TDLS, as the queues are dynamically created anyway,
so no need to allocate them ahead of time.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This led to a DMA splat.

Fixes: a6c4fb44 ("iwlwifi: mvm: Add FW paging mechanism for the UMAC on PCI")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The value for Channel 14 was wrong. Fix it.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Those comments were wrong, fix them.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The TX fifos are arranged consecutively in the SMEM, beginning
with the regular fifos, and tailed by the internal fifos.
In the current code, while trying to read the internal fifos,
we read the fifos beginning with the index zero.
By doing this we actually re-read the regular fifos.

In order to read the internal fifos, start the reading index
from the number of regular fifos configured by the fw.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Fixes: 39654cb3 ("iwlwifi: don't access a nonexistent register upon assert")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Read the SAR BIOS table from the ACPI and parse it into the
iwl_mvm_sar_table structure.  If the table is enabled, send it to the
firmware via REDUCE_TX_POWER_CMD.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We removed support for old API for coexistence, but we
forgot to remove defines and variable that are not needed
anymore.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Our HW does not support checksum of fragmented packets.
Fix code accordingly to checksum those packets in the driver.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Fixes: 5e6a98dc ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently the state sent in SF configuration is always
FULL_ON.
This commit sets the correct state (e.g. INIT_OFF
when station is not associated).

Fixes: commit f4a3ee49 ("iwlwifi: mvm: Always enable the smart FIFO")
Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For 9000 family we will get extended statistics notification
with averaged data for RSSI, TCM and rogue AP detection.
Support it. Future patches will added the required algorithms.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Newer hardware supports GCMP and GCMP 256-bit ciphers.
Add support for adding/setting GCMP key for TX mode.

In the TX command handling GCMP-256 is handled in a different
way as the key size should be up to 128-bits:
Set the key value to the key index in the key table,
and specify that this key should be taken form the key table
instead of from the TX command.

While at it - convert security control flags to an enum.
Signed-off-by: NAyala Beker <ayala.beker@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Fix an issue where nullfunc frames and block ack requests
had the same tid as aggregation frames and were queued on
a non aggregation queue. The pending frames counter included
those frames but the check whether to decrement the pending
frames counter relied on the tid status and not on the txq id.
The result was an inconsistent state of the pending frames
counter followed by a failure to remove the station.
This failure triggered SYSASSERT 0x3421.

In addition, fix a situation in DQA mode where the number
of pending frames turned negative. This was due to the TX queue
being on the IWL_EMPTYING_HW_QUEUE_DELBA state and its frames
were still decremented.

Even though the SYSASSERT issue is fixed when DQA is disabled,
the issue is not completely solved when DQA is enabled and
should still be fixed.
Signed-off-by: NOren Givon <oren.givon@intel.com>
Fixes: cf961e16 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

gcc is apparently unablel to track the state of the local 'resp_v2'
variable across the kzalloc() function, and warns about the response
variable being used without an initialization:

drivers/net/wireless/intel/iwlwifi/mvm/nvm.c: In function ‘iwl_mvm_update_mcc’:
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c:727:36: warning: ‘mcc_resp_v1’ may be used uninitialized in this function [-Wmaybe-uninitialized]
   resp_cp->n_channels = mcc_resp_v1->n_channels;
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c:721:3: warning: ‘mcc_resp’ may be used uninitialized in this function [-Wmaybe-uninitialized]
   memcpy(resp_cp, mcc_resp, resp_len);

The warning showed up in x86 allmodconfig after my patch to
unhide -Wmaybe-uninitialized warnings by default was merged,
though it always existed in randconfig builds. I did not
catch the warning earlier because I was testing on ARM, which
never produced the warning.

This rearranges the code in a way that improves readability for
both humans and the compiler, and that avoids the warning.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 6fa52430 ("iwlwifi: mvm: change mcc update API")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Expand TLC to support 160MHz channels. Full support for A-MSDU
case will be added separately.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

FW sets status for each RX packet.
Enum in the driver doesn't match with FW definition - fix it.
Signed-off-by: NAyala Beker <ayala.beker@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently we try to open an aggregation for every packet (given that one
is not already open).

This causes redundant overhead (addba/delba) for null data packets.

Do not open an aggregation for null data packets.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We convert the mvm device to a PCI device and then back again when
trying to find the handle for the device's ACPI data.  This is
unnecessary, so it can be removed.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support sending the DQA-enablement HCMD to the FW when
working in DQA mode.

This HCMD will enable DQA-specific flows in the FW.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In DQA mode the AUX queue is mapped elsewhere than in non-
DQA mode. Update the code to reflect this.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Set the correct sta_id in the SCD_QUEUE_CONFIG command sent
to the FW when enabling/disabling queues. This is needed in
DQA-mode to allow the FW to associate between queue and STA.

In case the queue isn't connected to a specific station but
rather is a static "generic" queue - the sta_id should be
set to 0x10 (max supported STA is 0x0f).
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support DQA queue sharing when no free queue exists for
allocation to a STA that already exists. This means that
a single queue will serve more than a single TID (although
the RA will be the same for all TIDs served).

We try to choose the lowest AC possible, to ensure the
shared queues have the lowest possible combined AC
requirements. The queue to share is chosen only from the
same RA's DATA queues as follows (in descending priority):
 1. An AC_BE queue
 2. Same AC queue
 3. Highest AC queue that is lower than new AC
 4. Any existing AC (there always is at least 1 DATA queue)

If any aggregations existed for any of the TIDs of the
shared queue - they are stopped (the FW is notified), but
no delBA is sent.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

"max_amsdu_len" isn't set if kstrtouint() fails.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We never initialize ampdu_status so it causes a static checker warning
when we pass it to iwl_mvm_pass_packet_to_mac80211().  Fortunately, it's
never used so we can just remove it.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Some transports may sleep when writing to registers, which is done
when calling iwl_force_nmi().  So we can't call iwl_force_nmi() in a
timer context.  To solve that, convert the scan timeout timer to a
delayed work.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Theoretically we may get only one IRQ from OS, in which
case we will have only 1 queue even in MSIx mode.
This will cause division by zero in the indirection table
calculation.
We do not need send the command in that case, as there is
only one queue so all RX traffic will be directed to it
anyway. Bail out early if there is only one queue.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support marking queues as inactive upon a timeout expiring,
and allow inactive queues to be re-assigned to other RA/TIDs
if no other queue is free.

This is done by keeping a timestamp of the latest frame TXed
for every RA/TID, and then going over the queues currently in
use when a new queue is needed, inactivating all those that
are inactive.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For some reason, the FRAME_RELEASE message handling for the
default queue ended up being in the only/default queue for
non-RSS devices; fix that and handle FRAME_RELEASE properly
on the default queue for RSS devices.

Fixes: 585a6fcc ("iwlwifi: mvm: infrastructure for frame-release message")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add support CSA countdown offloading. When CSA starts, the driver
specifies the offsets to the eCSA and CSA IEs in the beacon template
command and the fw performs the countdown.
The fw notifies the driver when the channel switch flow
should be performed.
Beacon sent notifications are not used anymore.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>