- 28 1月, 2012 1 次提交
-
-
由 Sekhar Nori 提交于
Commit 5a05a820 ("davinci_emac: use an unique MDIO bus name") introduced during the v3.3 merge window updated the davinci mdio bus name to make it unique. Update the bus name in board files which use DaVinci MDIO bus to match the new name. Without this PHY is not detected with error like: PHY 0:01 not found net eth0: could not connect to phy 0:01 Tested on DM365 and DA850 EVMs. Cc: Florian Fainelli <florian@openwrt.org> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: NSekhar Nori <nsekhar@ti.com>
-
- 05 1月, 2012 1 次提交
-
-
由 Sekhar Nori 提交于
Rather than using DaVinci specific davinci_soc_info based restart hook, use the restart hook available in the machine descriptor instead. Tested on DM365 and AM18x EVMs. v2: Changed to use restart hook in machine descriptor per Russell's comment. Signed-off-by: NSekhar Nori <nsekhar@ti.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 11 9月, 2011 2 次提交
-
-
由 Brian Norris 提交于
Recall the recently added prefix requirements: * "NAND_" for flags in nand.h, used in nand_chip.options * "NAND_BBT_" for flags in bbm.h, used in nand_chip.bbt_options or in nand_bbt_descr.options Thus, I am changing NAND_USE_FLASH_BBT to NAND_BBT_USE_FLASH. Again, this flag is found in bbm.h and so should NOT be used in the "nand_chip.options" field. Signed-off-by: NBrian Norris <computersforpeace@gmail.com> Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
-
由 Brian Norris 提交于
This patch works with the following three flags from two headers (nand.h and bbm.h): (1) NAND_USE_FLASH_BBT (nand.h) (2) NAND_USE_FLASH_BBT_NO_OOB (nand.h) (3) NAND_BBT_NO_OOB (bbm.h) These flags are all related and interdependent, yet they were in different headers. Flag (2) is simply the combination of (1) and (3) and can be eliminated. This patch accomplishes the following: * eliminate NAND_USE_FLASH_BBT_NO_OOB (i.e., flag (2)) * move NAND_USE_FLASH_BBT (i.e., flag (1)) to bbm.h It's important to note that because (1) and (3) are now both found in bbm.h, they should NOT be used in the "nand_chip.options" field. I removed a small section from the mtdnand DocBook because it referes to NAND_USE_FLASH_BBT in nand.h, which has been moved to bbm.h. Signed-off-by: NBrian Norris <computersforpeace@gmail.com> Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
-
- 22 8月, 2011 1 次提交
-
-
由 Nicolas Pitre 提交于
Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org> Acked-by: NArnd Bergmann <arnd@arndb.de>
-
- 19 7月, 2011 1 次提交
-
-
由 Nicolas Pitre 提交于
Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
-
- 31 3月, 2011 1 次提交
-
-
由 Lucas De Marchi 提交于
Fixes generated by 'codespell' and manually reviewed. Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>
-
- 20 10月, 2010 1 次提交
-
-
由 Nicolas Pitre 提交于
Since we're now using addruart to establish the debug mapping, we can remove the io_pg_offst and phys_io members of struct machine_desc. The various declarations were removed using the following script: grep -rl MACHINE_START arch/arm | xargs \ sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }' [ Initial patch was from Jeremy Kerr, example script from Russell King ] Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org> Acked-by: Eric Miao <eric.miao at canonical.com>
-
- 24 9月, 2010 1 次提交
-
-
由 Cyril Chemparathy 提交于
This patch removes davinci architecture code that has now been rendered useless by the previous patches in the MDIO separation series. In addition, the earlier phy_mask definitions have been replaced with corresponding phy_id definitions. Signed-off-by: NCyril Chemparathy <cyril@ti.com> Tested-by: NMichael Williamson <michael.williamson@criticallink.com> Tested-by: NCaglar Akyuz <caglarakyuz@gmail.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
- 14 5月, 2010 1 次提交
-
-
由 Cyril Chemparathy 提交于
This patch implements the following: - interrupt initialization uses ioremap() instead of passing a virtual address via davinci_soc_info. - machine definitions directly point to cp_intc_init() or davinci_irq_init() - davinci_intc_type and davinci_intc_base now get initialized in controller specific init functions instead of davinci_common_init() - minor fix in davinci_irq_init() to use intc_irq_num instead of DAVINCI_N_AINTC_IRQ Signed-off-by: NCyril Chemparathy <cyril@ti.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
- 07 5月, 2010 3 次提交
-
-
由 Sergei Shtylyov 提交于
The IDE platform device is registered in three different places (2 board files for DM644x and in dm646x.c for DM646x) while both the IDE base address and the IDE IRQ are the same for both SoCs -- therefore, the proper place for the IDE platform seems to be in devices.c. Merge the IDE platform data and registration code and create davinci_init_ide() in place of dm646x_init_ide()... Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
由 Sergei Shtylyov 提交于
Currently each DaVinci board file #define's its own version of the EMIFA base addresses (all named DAVINCI_ASYNC_EMIF_*_BASE), which leads to duplication. Move these #define's to the SoC specific headers, changing their prefixes from 'DAVINCI' to the 'DM355', 'DM644X', and 'DM646X' since all these base addresses are SoC specific... And while at it, rename DM646X_ASYNC_EMIF_DATA_CE0_BASE to DM646X_ASYNC_EMIF_CS2_SPACE_BASE in order to match the DM646x datasheet. Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
由 Kevin Hilman 提交于
- Convert data/functions to static - include headers for missing declarations - pointer cleanups: struct foo *__iomem f --> struct foo __iomem *f; Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
- 26 11月, 2009 1 次提交
-
-
由 Andrey Porodko 提交于
The Neuros OSD 2.0 is the hardware component of the Neuros Open Internet Television Platform. Hardware is very close to Ti DM644X-EVM board. It has: DM6446M02 module with 256MB NAND, 256MB RAM, TLV320AIC32 AIC, USB, Ethernet, SD/MMC, UART, THS8200, TVP7000 for video. Additionaly realtime clock, IR remote control receiver, IR Blaster based on MSP430 (firmware although is different from used in DM644X-EVM), internal ATA-6 3.5” HDD drive with PATA interface, two muxed red-green leds. For more information please refer to http://wiki.neurostechnology.com/index.php/OSD_2.0_HDSigned-off-by: NAndrey Porodko <panda@chelcom.ru> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-