Self-explanatory.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The flash memory for the ice hardware contains a block of information
used for link management called the Netlist module.

As this essentially represents another section of firmware, add its
version information to the output of the driver's .info_get handler.

This includes both a version and the first few bytes of a hash of the
module contents.

  fw.netlist -> the version information extracted from the netlist module
  fw.netlist.build-> first 4 bytes of the hash of the contents, similar
                     to fw.mgmt.build
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When reading from the NVM using a flat address, it is useful to know the
upper bound on the size of the flash contents. This value is not stored
within the NVM.

We can determine the size by performing a bisection between upper and
lower bounds. It is known that the size cannot exceed 16 MB (offset of
0xFFFFFF).

Use a while loop to bisect the upper and lower bounds by reading one
byte at a time. On a failed read, lower the maximum bound. On
a successful read, increase the lower bound.

Save this as the flash_size in the ice_nvm_info structure that contains
data related to the NVM.

The size will be used in a future patch for implementing full NVM read
via ethtool's GEEPROM command.

The maximum possible size for the flash is bounded by the size limit for
the NVM AdminQ commands. Add a new macro, ICE_AQC_NVM_MAX_OFFSET, which
can be used to represent this upper bound.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The NVM contents are read via firmware by using the ice_aq_read_nvm
function. This function has a couple of limits:

1) The AdminQ commands can only take buffers sized up to 4Kb. Thus, any
   larger read must be split into multiple reads.
2) when reading from the Shadow RAM, reads must not cross sector
   boundaries. The sectors are also 4Kb in size.

Implement the ice_read_flat_nvm function to read portions of the NVM by
flat offset. That is, to read using offsets from the start of the NVM
rather than from a specific module.

This function will be able to read both from the NVM and from the Shadow
RAM. For simplicity NVM reads will always be broken up to not cross 4Kb
page boundaries, even though this is not required unless reading from
the Shadow RAM.

Use this new function as the implementation of ice_read_sr_word_aq.

The ice_read_sr_buf_aq function is not modified here. This is because
a following change will remove the only caller of that function in favor
of directly using ice_read_flat_nvm. Thus, there is little benefit to
changing it now only to remove it momentarily. At the same time, the
ice_read_sr_aq function will also be removed.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we are not handling LAN overflow events. There can be cases
where LAN overflow events occur on VF queues, especially with Link Flow
Control (LFC) enabled on the controlling PF. In order to recover from
the LAN overflow event caused by a VF we need to determine if the queue
belongs to a VF and reset that VF accordingly.

The struct ice_aqc_event_lan_overflow returns a copy of the GLDCB_RTCTQ
register, which tells us what the queue index is in the global/device
space. The global queue index needs to first be converted to a PF space
queue index and then it can be used to find if a VF owns it.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is a collection of trivial fixes including fixing whitespace, typos,
function headers, reverse Christmas tree, etc.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Write the hardware tables based on the populated software structures.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Store the TCAM entry with the profile data and the VSI group in the
respective SW structures. This will be subsequently used to write out
the tables to hardware.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Create an extraction sequence based on the packet header protocols to be
programmed and allocate a flow profile for the extraction sequence.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Allow for rate limiting Tx queues. Bitrate is set in
Mbps(megabits per second).

Mbps max-rate is set for the queue via sysfs:
/sys/class/net/<iface>/queues/tx-<queue>/tx_maxrate
ex: echo 100 >/sys/class/net/ens7/queues/tx-0/tx_maxrate
    echo 200 >/sys/class/net/ens7/queues/tx-1/tx_maxrate
Note: A value of zero for tx_maxrate means disabled,
default is disabled.
Signed-off-by: NUsha Ketineni <usha.k.ketineni@intel.com>
Co-developed-by: NTarun Singh <tarun.k.singh@intel.com>
Signed-off-by: NTarun Singh <tarun.k.singh@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Print message to inform user if unsupported module is inserted, and
extend the topology / configuration detection.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement ethtool -m support to read eeprom data from SFP/QSFP modules.
Signed-off-by: NScott W Taylor <scott.w.taylor@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the required defines, structures, and functions to enable downloading
a DDP package.  Before download, checks are performed to ensure the package
is valid and compatible.

Note that package download is not yet requested by the driver as further
initialization is required to utilize the package.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver is required to send a version to the firmware
to indicate that the driver is up. If the driver doesn't
do this the firmware doesn't behave properly.
Signed-off-by: NPaul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch limits the max TCs set by the driver to the value provided by
the firmware as per the capabilities of the device. Otherwise, hard coding
to 8 TC max would fail the device configurations with more than 4 ports.
Signed-off-by: NUsha Ketineni <usha.k.ketineni@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

According to recent specification versions, the field in the Queue Shutdown
AdminQ command consisting of the "driver unloading" indication is not a 4
byte field (it is byte.bit 16.0).  Change it to a byte and remove the
unnecessary endian conversion.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In some circumstances, VF devices can be deactivated while a message is
in-flight. In that case, a series of scary error message will be
printed in the log. Since these are actually harmless, check for this
case and suppress them. No harm, no foul.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch mostly capitalizes abbreviations in code comments. Fixed some
typos and removed some unnecessary newlines as well.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The define describing the bits for the struct field should be below
the field itself.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current specification has updates to the command formats for
manage MAC opcodes (opcodes 0x0107 and 0x0108) and get PHY caps
(opcode 0x0600). Update the code to reflect this.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds driver support for Forward Error Correction (FEC)
and ethtool handlers to set/get FEC params.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In order to initialize the current status of the FW logging,
this patch adds ice_get_fw_log_cfg. The function retrieves
the current setting of the FW logging from HW and updates the
ice_hw structure accordingly.
Signed-off-by: NDan Nowlin <dan.nowlin@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a handler for ethtool selftest. Selftest includes
testing link, interrupts, eeprom, registers and packet loopback.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support to set 52 byte RSS hash key.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds code to start or stop LLDP and DCBX in firmware through
use of ethtool private flags.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a new function ice_pf_dcb_cfg (and related helpers)
which applies the DCB configuration obtained from the firmware. As
part of this, VSIs/netdevs are updated with traffic class information.

This patch requires a bit of a refactor of existing code.

1. For a MIB change event, the associated VSI is closed and brought up
   again. The gap between closing and opening the VSI can cause a race
   condition. Fix this by grabbing the rtnl_lock prior to closing the
   VSI and then only free it after re-opening the VSI during a MIB
   change event.

2. ice_sched_query_elem is used in ice_sched.c and with this patch, in
   ice_dcb.c as well. However, ice_dcb.c is not built when CONFIG_DCB is
   unset. This results in namespace warnings (ice_sched.o: Externally
   defined symbols with no external references) when CONFIG_DCB is unset.
   To avoid this move ice_sched_query_elem from ice_sched.c to
   ice_common.c.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch introduces a new top level function ice_init_dcb (and
related lower level helper functions) which continues the DCB init
flow.

This function uses ice_get_dcb_cfg to get, parse and store the DCB
configuration. Once this is done, it sets itself up to be notified
by the firmware on LLDP MIB change events.
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch introduces a skeleton for ice_init_pf_dcb, the top level
function for DCB initialization. Subsequent patches will add to this
DCB init flow.

In this patch, ice_init_pf_dcb checks if DCB is a supported capability.
If so, an admin queue call to start the LLDP and DCBx in firmware is
issued. If not, an error is reported. Note that we don't fail the driver
init if DCB init fails.
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Capitalize abbreviations and spell out some that aren't obvious.
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In the ice_aq_set_phy_cfg AQ command, the 16.4 bit is reserved. This
patch will make sure that this bit will never be set to 1.
Signed-off-by: NChinh T Cao <chinh.t.cao@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds code for the detection and operation of several
additional PHY types that support higher link speeds.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When a netdev is set up/down we need to set the phsyical link state
accordingly. This patch adds that functionality by calling
ice_force_phys_link_state(vsi, link_up) in both the ice_stop() and
ice_open() paths.

In order to force link, ice_force_phys_link_state(vsi, link_up) will
first determine the current phy capabilities. If link has not changed
there is nothing to do. If link has changed, previous PHY capabilities
are saved and the "Enable Automatic Link Update" and "Link Establishment
State Machine (LESM)" enable bits are set. Then the new PHY config is
saved. The "Enable Automatic Link Update" will force the FW to execute
Setup link and restart auto-negotiation. This *should* then result in a
"Link Status Event (LSE)" which will cause the driver to get the current
link status.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add led blinking handler to ethtool. Since led blinking is
controlled by FW/HW only ETHTOOL_ID_ACTIVE and ETHTOOL_ID_INACTIVE
are really needed.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The following functions were refactored to call a new common function,
ice_aqc_send_sched_elem_cmd():

- ice_aq_add_sched_elems()
- ice_aq_delete_sched_elems()
- ice_aq_move_sched_elems()
- ice_aq_query_sched_elems()
- ice_aq_cfg_sched_elems()
- ice_aq_suspend_sched_elems()
- ice_aq_resume_sched_elems()
Signed-off-by: NGreg Priest <greg.priest@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

1. Fix several cases of double spacing
2. Fix typos
3. Capitalize abbreviations
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixes bad masks that would break compilation when evaluated.
Signed-off-by: NLev Faerman <lev.faerman@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we are setting the guar_num_vsi to equal to ICE_MAX_VSI
which is the device limit of 768. This is incorrect and could have
unintended consequences. To fix this use the valid_function's 8-bit
bitmap returned from discovering device capabilities to determine the
guar_num_vsi per function. guar_num_vsi value is then passed on to
pf->num_alloc_vsi.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

virtchnl is a protocol/interface specification that allows the Intel
"Adaptive Virtual Function (AVF)" driver (iavf.ko) to work with more than
one physical function driver. The AVF driver sends "virtchnl commands"
(control plane only) to the PF driver over mailbox queues and the PF driver
executes these commands and returns a result to the VF, again over mailbox.

This patch adds AVF support for the ice PF driver by implementing the
following virtchnl commands:

VIRTCHNL_OP_VERSION
VIRTCHNL_OP_GET_VF_RESOURCES
VIRTCHNL_OP_RESET_VF
VIRTCHNL_OP_ADD_ETH_ADDR
VIRTCHNL_OP_DEL_ETH_ADDR
VIRTCHNL_OP_CONFIG_VSI_QUEUES
VIRTCHNL_OP_ENABLE_QUEUES
VIRTCHNL_OP_DISABLE_QUEUES
VIRTCHNL_OP_ADD_ETH_ADDR
VIRTCHNL_OP_DEL_ETH_ADDR
VIRTCHNL_OP_CONFIG_VSI_QUEUES
VIRTCHNL_OP_ENABLE_QUEUES
VIRTCHNL_OP_DISABLE_QUEUES
VIRTCHNL_OP_REQUEST_QUEUES
VIRTCHNL_OP_CONFIG_IRQ_MAP
VIRTCHNL_OP_CONFIG_RSS_KEY
VIRTCHNL_OP_CONFIG_RSS_LUT
VIRTCHNL_OP_GET_STATS
VIRTCHNL_OP_ADD_VLAN
VIRTCHNL_OP_DEL_VLAN
VIRTCHNL_OP_ENABLE_VLAN_STRIPPING
VIRTCHNL_OP_DISABLE_VLAN_STRIPPING
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Post VF initialization, there are a couple of different ways in which a
VF reset can be triggered. One is when the underlying PF itself goes
through a reset and other is via a VFLR interrupt. ice_reset_vf introduced
in this patch handles both these cases.

Also introduced in this patch is a helper function ice_aq_send_msg_to_vf
to send messages to VF over the mailbox queue. The PF uses this to send
reset notifications to VFs.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Mailbox queue is a type of control queue that's used for communication
between PF and VF. This patch adds code to initialize, configure and
use mailbox queues.

This patch also adds support to detect and parse SR-IOV capabilities
returned by the hardware.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>