This is the driver for latest Blackfin on-chip nand flash controller

 - use nand_chip and mtd_info common nand driver interface
 - provide both PIO and dma operation
 - compiled with ezkit bf548 configuration
 - use hardware 1-bit ECC
 - tested with YAFFS2 and can mount YAFFS2 filesystem as rootfs

ChangeLog from try#1
 - use hweight32() instead of count_bits()
 - replace bf54x with bf5xx and BF54X with BF5XX
 - compare against plat->page_size in 2 cases when enable hardware ECC

ChangeLog from try#2
 - passed nand_test suites
 - use cpu_relax() instead of busy wait loop
 - some coding style issue pointed out by Andrew
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

When we press ctrl-alt-del,kernel_restart_prepare will invoke 
cfi_intelext_reboot which will set flash to read array mode, but later 
when device_shutdown is invoked which may put current work queue to 
sleep and other process may be scheduled to running and programming 
flash in not FL_READY mode again. So we can't boot up if this flash is 
used for bootloader.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

drivers/mtd/nand/alauda.c: In function 'alauda_bounce_read':
drivers/mtd/nand/alauda.c:412: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

In three places: summary scan, normal scan, REF_PRISTINE GC.

Just truncate at the NUL, since that was the correct thing to do in the
only case where this (inexplicable) breakage has been seen.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

I have no idea how this happened, but OLPC trac #4184 suggests that it
did. Catch it early.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

... where we'll actually print the count in a debug message.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

In OLPC trac #4184 we found a case where a corrupted node didn't
actually get obsoleted when we tried to garbage-collect it. So we wrote
out many million copies of it, in repeated attempts to obsolete it,
until the flash became full. Don't Do That.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Instead of matching resv_blocks_gcmerge, which is only about 3, instead
match resv_blocks_gctrigger, which includes a proportion of the total
device size.

These ought to become tunable from userspace, at some point.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

With huge amounts of free space, we weren't bothering to GC for while a
while, and pathological numbers of obsolete nodes were accumulating,
seriously affecting performance on NAND flash (OLPC trac #3978)
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

When the erase callback performs some other action on the flash, it's
highly likely to deadlock unless we actually release the chip lock
before calling it.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Originally from Marcelo; modified to put the original timing registers
back instead of 0xFFFFFFFF.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

It was only the very early prototypes which made the mistake of using
the same device ident for all three functions on the device -- don't
bother trying to express that in the PCI match table, since the tools
don't cope. We can check in the probe routine instead, just in case.
Also remember to terminate the table.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Fixup the includes which have been moved around
when changing the s3c24xx arch support.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This patch make the OneNAND driver much less racy. It fixes
our "onenand_wait: read timeout!" heisenbugs. The reason of
these bugs was that the driver did not lock the chip when
accessing OTP, and it screwed up OneNAND state when the OTP
was read while JFFS2 was doing FS checking.

This patch also fixes other races I spotted:
1. BBT was not protected
2. Access to ecc_stats was not protected

Now the chip is locked when BBT is accessed.

To fix all of these I basically split all interface functions
on 'function()' and 'function_nolock()' parts.

I tested this patch on N800 hardware - it fixes our problems.
But I tested a little different version because our OneNAND
codebase is slightly out-of-date. But it should be OK.

This patch also includes the prin fixes I posted before.
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

The Vermilion Range Expansion Bus supports four chip selects, each of which
has 64MiB of address space.  The 2nd BAR of the Expansion Bus PCI Device
is a 256MiB memory region containing the address spaces for all four of
the chip selects, with start addresses hardcoded on 64MiB boundaries.

This map driver only supports NOR flash on chip select 0.  The buswidth
(either 8 bits or 16 bits) is determined by reading the Expansion Bus Timing
and Control Register for Chip Select 0 (EXP_TIMING_CS0).
Signed-off-by: NAndy Lowe <alowe@mvista.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Fix a couple of instances in JFFS2 where the unpoint() routine is
being called with the wrong length in cases where the point() routine
truncated a request.
Signed-off-by: NAndy Lowe <alowe@mvista.com>
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

The CFI probe routine is capable of detecting flash banks consisting of
identical chips mapped to physically discontiguous addresses.  (One
common way this can occur is if a flash bank is populated with chips of
less capacity than the hardware was designed to support.)  The CFI
point() routine currently ignores any such gaps.  This patch fixes
the CFI point() routine so that it truncates any request that would
span a gap.
Signed-off-by: NAndy Lowe <alowe@mvista.com>
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Replace Lubbock and Mainstone board drivers with common PXA2xx driver,
convert to platform driver (corresponding platform device changes merged
to kernel.org for 2.6.15), add power management callbacks.
Signed-off-by: NTodd Poynor <tpoynor@mvista.com>
Signed-off-by: NNicolas Pitre <npitre@mvista.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Document mtd erase interface.
Signed-off-by: NJörn Engel <joern@logfs.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This patch has removed Momenco Ocelot support from MTD.
Ocelot support has already removed.
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Make nandsim use GFP_NOFS when allocating memory, because it might
be used by a file-system (e.g. UBIFS2) which means, if we are short
of memory, we may deadlock. Indee, UBIFS is holding a lock, writes
to the media, reaches this place in NANDsim, kmalloc does not find
the requested amount of RAM, calls memory shrinker, which decides
to writeback inodes, calls FS, and it deadlocks on the lock which
is already being held. Below is the UBIFS backtrace which
demonstrates that:

[<c03717dc>] __mutex_lock_slowpath+0xc8/0x2e6
[<c0371a16>] mutex_lock+0x1c/0x1f
[<f8b9d076>] reserve_space+0x3d/0xa9 [ubifs]
[<f8b9d1bd>] make_one_reservation+0x2b/0x86 [ubifs]
[<f8b9d3fc>] ubifs_jrn_write_block+0xda/0x12f [ubifs]
[<f8b9ff3a>] ubifs_writepage+0x11d/0x1ec [ubifs]
[<c015d6ab>] shrink_inactive_list+0x7fa/0x969
[<c015d8c8>] shrink_zone+0xae/0x10c
[<c015e3b4>] try_to_free_pages+0x159/0x251
[<c015980a>] __alloc_pages+0x125/0x2f0
[<c016ff6a>] cache_alloc_refill+0x380/0x6ba
[<c01703f3>] __kmalloc+0x14f/0x157
[<f885722a>] do_state_action+0xab7/0xc74 [nandsim]
[<f885760c>] switch_state+0x225/0x402 [nandsim]
[<f8857e7e>] ns_hwcontrol+0x3e2/0x620 [nandsim]
[<f8862f53>] nand_command+0x2e/0x1a5 [nand]
[<f8861ad8>] nand_write_page+0x4a/0x9a [nand]
[<f88617b4>] nand_do_write_ops+0x1cf/0x343 [nand]
[<f8861a70>] nand_write+0x88/0xa6 [nand]
[<f8850b0e>] part_write+0x72/0x8b [mtd]
[<f88e19c5>] ubi_io_write+0x189/0x29c [ubi]
[<f88dfb98>] ubi_eba_write_leb+0xb6/0x699 [ubi]
[<f88def93>] ubi_leb_write+0xe4/0xe9 [ubi]
[<f8ba3b82>] ubifs_wbuf_write_nolock+0x333/0x4c9 [ubifs]
[<f8b9d28c>] write_node+0x74/0x8e [ubifs]
[<f8b9d422>] ubifs_jrn_write_block+0x100/0x12f [ubifs]
[<f8b9ff3a>] ubifs_writepage+0x11d/0x1ec [ubifs]
[<c0159e5b>] __writepage+0xb/0x26
[<c015a318>] write_cache_pages+0x203/0x2d9
[<c015a411>] generic_writepages+0x23/0x2d
[<c015a452>] do_writepages+0x37/0x39
[<c018e24a>] __writeback_single_inode+0x96/0x399
[<c018e903>] sync_sb_inodes+0x1a3/0x274
[<c018ebf3>] writeback_inodes+0xa6/0xd8
[<c015a9dd>] background_writeout+0x86/0x9e
[<c015ae9c>] pdflush+0xfb/0x1b6
[<c01387d7>] kthread+0x37/0x59
[<c0104dc3>] kernel_thread_helper+0x7/0x14

The deadlock is funny because it starts in pdflush/writeback,
and comes back to writeback, then deadlocks. It seems we should look
carefully for other places in UBI and MTD and use GFP_NOFS instead
of GFP_KERNEL.
Caught-by: NAdrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

When building NOR flash support, you have compile-time options for the
bus width and the number of individual chips which are interleaved
together onto that bus. The code to deal with arbitrary geometry is a
bit convoluted, and people want to just configure it for the specific
hardware they have, to avoid the runtime overhead.

Selecting _none_ of the available options doesn't make any sense. You
should have at least one. This makes it build though, since people
persist in trying.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Now we can use yaffs2 on OneNAND
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

To enable the main read/write at oob ops

Next time we will commit the main read/write support for yaffs2
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Unlike most stuff on the market the chip inside these two allows raw
flash access and doesn't implement and FTL, leaving that functionality
to the device driver.

Raw flash access in a cheap USB cardreader!  An MTD test device one can
attach to a PC!  What a deal!

The command set of the chip is not documented, so information was
obtained from the existing mass-storage driver
(drivers/usb/storage/alauda.c), its documentation
(http://alauda.sourceforge.net/wikka.php?wakka=BulkCommandReference),
additional reverse engineering and comparison with a vendor driver for a
related chip
(http://www.ratocsystems.com/english/download/driver/linux/sma03u.html).
Signed-off-by: NJoern Engel <joern@logfs.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

The tqm834x map Kconfig options depends on TQM834x which does not
exist anywhere else in the kernel.

The pq2fads map Kconfig/makefile support was removed a while ago but
the actual file persisted.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

These drivers are specific to 4xx support in arch/ppc at the moment.  Make
sure they don't get built on arch/powerpc.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The NUMA layer only supports NUMA policies for the highest zone.  When
ZONE_MOVABLE is configured with kernelcore=, the the highest zone becomes
ZONE_MOVABLE.  The result is that policies are only applied to allocations
like anonymous pages and page cache allocated from ZONE_MOVABLE when the
zone is used.

This patch applies policies to the two highest zones when the highest zone
is ZONE_MOVABLE.  As ZONE_MOVABLE consists of pages from the highest "real"
zone, it's always functionally equivalent.

The patch has been tested on a variety of machines both NUMA and non-NUMA
covering x86, x86_64 and ppc64.  No abnormal results were seen in
kernbench, tbench, dbench or hackbench.  It passes regression tests from
the numactl package with and without kernelcore= once numactl tests are
patched to wait for vmstat counters to update.

akpm: this is the nasty hack to fix NUMA mempolicies in the presence of
ZONE_MOVABLE and kernelcore= in 2.6.23.  Christoph says "For .24 either merge
the mobility or get the other solution that Mel is working on.  That solution
would only use a single zonelist per node and filter on the fly.  That may
help performance and also help to make memory policies work better."
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Acked-by: NLee Schermerhorn <lee.schermerhorn@hp.com>
Tested-by: NLee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: NChristoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

au1100fb_fb_blank() should come before au1100fb_setmode().

drivers/video/au1100fb.c: In function 'au1100fb_setmode':
drivers/video/au1100fb.c:211: error: implicit declaration of function 'au1100fb_fb_blank'
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

drivers/video/console/newport_con.c: In function `newport_console_init':
drivers/video/console/newport_con.c:743: warning: return makes integer from pointer without a cast

Although one wonders whether that should have been -ENODEV...

Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In file included from drivers/video/console/newport_con.c:16:
include/linux/selection.h:16: warning: "struct tty_struct" declared inside parameter list
include/linux/selection.h:16: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is the correct fix according to Paul Mackerras and allows an
allyesconfig on PPC64 to build.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Xen i386 xen-head.S fix sections mixup

xen-head.S does not come back to the data section, leaving the text section
as current section. It causes problems with a slightly enhanced DEBUG_RODATA
that supports CONFIG_HOTPLUG and bringing a CPU up after the text has been
marked read-only: reference to early_gdt_descr causes a page fault.

Updates:

- It should be using pushsection/popsection.
- Actually, the push/popsections around the ELFNOTEs are redundant; ELFNOTE()
  does its own push/popsection to put things into the appropriate .note* section
  anyway.
Signed-off-by: NMathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: NJeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

de_thread:

	if (atomic_read(&oldsighand->count) <= 1)
		BUG_ON(atomic_read(&sig->count) != 1);

This is not safe without the rmb() in between.  The results of two
correctly ordered __exit_signal()->atomic_dec_and_test()'s could be seen
out of order on our CPU.

The same is true for the "thread_group_empty()" case, __unhash_process()'s
changes could be seen before atomic_dec_and_test(&sig->count).

On some platforms (including i386) atomic_read() doesn't provide even the
compiler barrier, in that case these checks are simply racy.

Remove these BUG_ON()'s. Alternatively, we can do something like

	BUG_ON( ({ smp_rmb(); atomic_read(&sig->count) != 1; }) );
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Minor tweaks to rtc-max6902: make it hotplug correctly, and fix a few
space-before-tab whitespace botches.  This driver has no current in-tree
users, so the hotplug fix changes the driver name.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>