Signed-off-by: Nmajianpeng <majianpeng@gmail.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

There a two different irq variables ks->irq and netdev->irq.
Only ks->irq is set on probe, so disabling irq in ks_start_xmit fails.

This patches remove ks->irq from private data and use only netdev->irq.

Tested on a kernel 3.0 based OMAP4430 SMP Board
Signed-off-by: NJan Weitzel <j.weitzel@phytec.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VETH_INFO_PEER carries struct ifinfomsg plus optional IFLA
attributes. A minimal size of sizeof(struct ifinfomsg) must be
enforced or we may risk accessing that struct beyond the limits
of the netlink message.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the MAC HW initialization and
the HW feature verification from the open to the probe
function as D. Miller suggested.
So the patch actually reorganizes and tidies-up some parts of
the driver and indeed fixes some problem when tune its HW features.
These can be overwritten by looking at the HW cap register at
run-time and that generated problems.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: NFrancesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of we use an external Wake-Up IRQ line
(priv->wol_irq != dev->irq) we need to invoke the
request_irq.
Signed-off-by: NFrancesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If this bit is set and the CRC error is reset, then the packet is valid.
Only report this as stat info.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BugLink: http://bugs.launchpad.net/bugs/900802

Cc: stable@vger.kernel.org 3.2+
Signed-off-by: NTill Kamppeter <till.kamppeter@gmail.com>
Signed-off-by: NTim Gardner <tim.gardner@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add unicast steering entries to resource tracker.
Do qp_detach also for these entries when VF doesn't shut down gracefully.
Otherwise there is leakage of these resources, since they are not tracked.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When adding new unicast steer entry, before moving qp to state ready,
actually before calling mlx4_RST2INIT_QP_wrapper(), there were added
a lot of entries with local_qpn=0 into radix tree.
This fact impacted the get_res() function and proper functioning
of resource tracker in addition to adding trash entries into radix tree.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: NYevgeny Petrilin <yevgenyp@melllanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When passing MLX4_UC_STEER=1 it was translated to value 2
after mlx4_QP_ATTACH_wrapper. Therefore in new_steering_entry()
unicast steer entries were added to index 2 of array of size 2.
Fixing this bug by shift right to one position.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently registers with a value of 0 are ignored when initializing the register
defaults from raw defaults. This worked in the past, because registers without a
explicit default were assumed to have a default value of 0. This was changed in
commit b03622a8 ("regmap: Ensure rbtree syncs registers set to zero properly").
As a result registers, which have a raw default value of 0 are now assumed to
have no default. This again can result in unnecessary writes when syncing the
cache. It will also result in unnecessary reads for e.g. the first update
operation. In the case where readback is not possible this will even let the
update operation fail, if the register has not been written to before.

So this patch removes the check. Instead it adds a check to ignore raw defaults
for registers which are volatile, since those registers are not cached.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

Jean Delvare reported bonding on top of 3c59x adapters was not detecting
network cable removal fast enough.

3c59x indeed uses a 60 seconds timer to check link status if carrier is
on, and 5 seconds if carrier is off.

This patch reduces timer period to 5 seconds if device is a bonding
slave.
Reported-by: NJean Delvare <jdelvare@suse.de>
Acked-by: NJean Delvare <jdelvare@suse.de>
Acked-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'poll' was a debugging option, but turning it on these days leads to
kernel panic. Remove it.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MSI_REARM_EN register is a write only trigger register.
There is no need RMW when re-arming.

May fix:
https://bugs.freedesktop.org/show_bug.cgi?id=41668Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

- Add missing DFP6 connection state handling
- crtc routing bits not used on DCE4+

Noticed by sylware on phoronix.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Silly bad return path.

Reported-and-Tested-by: Mikko Vinni
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Current PIO mode makes a kernel crash with CONFIG_HIGHMEM.
Highmem pages have a NULL from sg_virt(sg).
This patch fixes the following problem.

Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 817 [#1] PREEMPT SMP
Modules linked in:
CPU: 0    Not tainted  (3.0.15-01423-gdbf465f #589)
PC is at dw_mci_pull_data32+0x4c/0x9c
LR is at dw_mci_read_data_pio+0x54/0x1f0
pc : [<c0358824>]    lr : [<c035988c>]    psr: 20000193
sp : c0619d48  ip : c0619d70  fp : c0619d6c
r10: 00000000  r9 : 00000002  r8 : 00001000
r7 : 00000200  r6 : 00000000  r5 : e1dd3100  r4 : 00000000
r3 : 65622023  r2 : 0000007f  r1 : eeb96000  r0 : e1dd3100
Flags: nzCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment
xkernel
Control: 10c5387d  Table: 61e2004a  DAC: 00000015
Process swapper (pid: 0, stack limit = 0xc06182f0)
Stack: (0xc0619d48 to 0xc061a000)
9d40:                   e1dd3100 e1a4f000 00000000 e1dd3100 e1a4f000 00000200
9d60: c0619da4 c0619d70 c035988c c03587e4 c0619d9c e18158f4 e1dd3100 e1dd3100
9d80: 00000020 00000000 00000000 00000020 c06e8a84 00000000 c0619e04 c0619da8
9da0: c0359b24 c0359844 e18158f4 e1dd3164 e1dd3168 e1dd3150 3d02fc79 e1dd3154
9dc0: e1dd3178 00000000 00000020 00000000 e1dd3150 00000000 c10dd7e8 e1a84900
9de0: c061e7cc 00000000 00000000 0000008d c06e8a84 c061e780 c0619e4c c0619e08
9e00: c00c4738 c0359a34 3d02fc79 00000000 c0619e4c c05a1698 c05a1670 c05a165c
9e20: c04de8b0 c061e780 c061e7cc e1a84900 ffffed68 0000008d c0618000 00000000
9e40: c0619e6c c0619e50 c00c48b4 c00c46c8 c061e780 c00423ac c061e7cc ffffed68
9e60: c0619e8c c0619e70 c00c7358 c00c487c 0000008d ffffee38 c0618000 ffffed68
9e80: c0619ea4 c0619e90 c00c4258 c00c72b0 c00423ac ffffee38 c0619ecc c0619ea8
9ea0: c004241c c00c4234 ffffffff f8810000 0000006d 00000002 00000001 7fffffff
9ec0: c0619f44 c0619ed0 c0048bc0 c00423c4 220ae7a9 00000000 386f0d30 0005d3a4
9ee0: c00423ac c10dd0b8 c06f2cd8 c0618000 c0594778 c003a674 7fffffff c0619f44
9f00: 386f0d30 c0619f18 c00a6f94 c005be3c 80000013 ffffffff 386f0d30 0005d3a4
9f20: 386f0d30 0005d2d1 c10dd0a8 c10dd0b8 c06f2cd8 c0618000 c0619f74 c0619f48
9f40: c0345858 c005be00 c00a2440 c0618000 c0618000 c00410d8 c06c1944 c00410fc
9f60: c0594778 c003a674 c0619f9c c0619f78 c004a7e8 c03457b4 c0618000 c06c18f8
9f80: 00000000 c0039c70 c06c18d4 c003a674 c0619fb4 c0619fa0 c04ceafc c004a714
9fa0: c06287b4 c06c18f8 c0619ff4 c0619fb8 c0008b68 c04cea68 c0008578 00000000
9fc0: 00000000 c003a674 00000000 10c5387d c0628658 c003aa78 c062f1c4 4000406a
9fe0: 413fc090 00000000 00000000 c0619ff8 40008044 c0008858 00000000 00000000
Backtrace:
[<c03587d8>] (dw_mci_pull_data32+0x0/0x9c) from [<c035988c>] (dw_mci_read_data_pio+0x54/0x1f0)
 r6:00000200 r5:e1a4f000 r4:e1dd3100
 [<c0359838>] (dw_mci_read_data_pio+0x0/0x1f0) from [<c0359b24>] (dw_mci_interrupt+0xfc/0x4a4)
[<c0359a28>] (dw_mci_interrupt+0x0/0x4a4) from [<c00c4738>] (handle_irq_event_percpu+0x7c/0x1b4)
[<c00c46bc>] (handle_irq_event_percpu+0x0/0x1b4) from [<c00c48b4>] (handle_irq_event+0x44/0x64)
[<c00c4870>] (handle_irq_event+0x0/0x64) from [<c00c7358>] (handle_fasteoi_irq+0xb4/0x124)
 r7:ffffed68 r6:c061e7cc r5:c00423ac r4:c061e780
 [<c00c72a4>] (handle_fasteoi_irq+0x0/0x124) from [<c00c4258>] (generic_handle_irq+0x30/0x38)
 r7:ffffed68 r6:c0618000 r5:ffffee38 r4:0000008d
 [<c00c4228>] (generic_handle_irq+0x0/0x38) from [<c004241c>] (asm_do_IRQ+0x64/0xe0)
 r5:ffffee38 r4:c00423ac
 [<c00423b8>] (asm_do_IRQ+0x0/0xe0) from [<c0048bc0>] (__irq_svc+0x80/0x14c)
Exception stack(0xc0619ed0 to 0xc0619f18)
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Sometimes a software reset is needed. Then some registers are saved and
restored but the interrupt mask register is missing. It causes issues
with sdio devices whose interrupts are masked after reset.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NJohan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: NUlf Hansson <ulf.hansson@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NNamjae Jeon <linkinjeon@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

If the driver is loaded with a card in the slot, mmc_add_host() will
schedule an immediate card-detection work, which will start IO and wait
for command completion. Usually the kernel first returns to the sh_mmcif
probe function, lets it finish and only then schedules the rescan work.
But sometimes, expecially under heavy system load, the work will be
scheduled immediately before returning to the probe method. In this case
it is important for the driver to be fully prepared for IO. For sh_mmcif
this means, that also the timeout work has to be initialised before
calling mmc_add_host(). It is also better to prepare interrupts
beforehand. Besides, since mmc_add_host() does card-detection itself,
there is no need to do it again immediately afterwards.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

When DMA is in use and the card is ejected during IO, DMA transfers have to
be terminated, otherwise the dmaengine driver fails to operate properly,
when the card is re-inserted.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Found this issue during code review. Actually, there are two issues which
both compensate together in lucky case.  In unlucky case the bus width
probing might not work as expected.
Signed-off-by: NJurgen Heeks <jurgen.heeks@nokia.com>
Reviewed-by: NNamjae Jeon <linkinjeon@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Modified the mmc_poweroff to resume before sending the poweroff
notification command. In sleep mode only AWAKE and RESET commands are
allowed, so before sending the poweroff notification command resume from
sleep mode and then send the notification command.

PowerOff Notify is tested on a Synopsis Designware Host Controller
(eMMC 4.5). The suspend to RAM and resume works fine.
Signed-off-by: NGirish K S <girish.shivananjappa@linaro.org>
Tested-by: NGirish K S <girish.shivananjappa@linaro.org>
Reviewed-by: NSaugata Das <saugata.das@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Set Medfield SDIO as non-removable to avoid un-necessary
card detect activity.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

There is an understood mismatch between the voltage the host controller is
set to and the voltage supplied to the card by a fixed voltage regulator.
Teaching the driver to accept the mismatch is overly complicated.  Instead
just accept the regulator's voltage.

This patch adds MMC_CAP2_BROKEN_VOLTAGE.

If the voltage didn't satisfy between min_uV and max_uV, try to change
the voltage in core.c.  When changing the voltage, maybe use
regulator_set_voltage().

In regulator_set_voltage(), check the below condition.

	/* sanity check */
	if (!rdev->desc->ops->set_voltage &&
	    !rdev->desc->ops->set_voltage_sel) {
		ret = -EINVAL;
		goto out;
	}

If some board should use the fixed-regulator, always return -EINVAL.
Then, eMMC didn't initialize always.

So if use a fixed-regulator, we need to add the MMC_CAP2_BROKEN_VOLTAGE.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch fixes the failure of low speed mmc card detection.
Signed-off-by: NGirish K S <girish.shivananjappa@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

When accessing the card on some FSL platform boards (e.g p2020, p1010,
mpc8536), the following error is reported with the timeout value calculated:

mmc0: Got data interrupt 0x00000020 even though no data operation was
in progress.
mmc0: Got data interrupt 0x00000020 even though no data operation was
in progress.

So we skip the calculation of timeout and use the max value to fix it.
Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: NGao Guanhua <B22826@freescale.com>
Signed-off-by: NXie Xiaobo <X.Xie@freescale.com>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

For some FSL ESDHC controllers (e.g. P2020E, Rev1.0), the SDHC can not
work on DMA mode because of the hardware bug, so we set a broken dma flag
and use PIO mode.
Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: NGao Guanhua <B22826@freescale.com>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Ensure clocks are always enabled before any interaction with the
host controller driver. This makes sure that there is no race
between host execution and the core layer turning off clocks
in different context with clock gating framework.
Signed-off-by: NSujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NPer Forlin <per.forlin@stericsson.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The voltage_ranges is supposed to switch from big endian to little endian.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NChris Ball <cjb@laptop.org>

A UHS sdio card that fails initialization at 1.8v signaling is not in
UHS mode.  We cannot use the speed in the the cis to reflect the bus
speed as this is the maxiumum value and will not reflect the fact
that the host is operating at a lower (non uhs) bus speed.
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Reviewed-by: NAaron Lu <aaron.lu@amd.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This fix a similar problem as in 72092cc4
and 481a8199 ("can:
fix NOHZ local_softirq_pending 08 warning"). This fix replaces netif_rx()
with netif_rx_ni() which has to be used from process/softirq context.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 619c5cb6 (New 7.0 FW: bnx2x, cnic, bnx2i, bnx2fc) added new
sparse warnings.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Vladislav Zolotarov <vladz@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 0869b3a4: ixp4xx-eth: use an unique MDIO bus name changed
the MDIO bus name from "0" to "ixp4xx-eth-0", as a result the PHY
name is not longer appropriate and will not match the MDIO bus name
so PHY connection will not succeed, fix that.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit "d6c25beb: mdio-octeon: use an unique MDIO bus name" changed the
octeon MDIO bus name from "0" to "mdio-octeon-0", change the PHY
formatting logic to account for that name change, so that PHY connection
on this bus succeeds.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit "391420f7: fec: use an unique MDIO bus name" first modified
the MDIO bus name to include the platform name, then in commit
"a7ed07d5: net: fec: correct phy_name buffer length when init phy_name"
the PHY name formatting was fixed in the case the PHY matches a PHY
driver.

The FEC driver however, also handles the case where we want to attach
to the fixed MDIO bus name, which was previously named "0", and now
"fixed-0". Change the PHY formatting logic to account for that.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 3e617506: bcm63xx_enet: use an unique MDIO bus name introduced
a regression in the PHY connection logic, since the PHY name was formatted
to expect the bus name to be "0" or "1", whereas it is now "bcm63xx-enet-0"
or "bcm63xx-enet-1".
Reported-by: NJoel EJC <joel_ejc@yahoofr>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit d1733f07: cpmac: use an unique MDIO bus name changed the MDIO bus
name from "1" to "cpmac-1", this breaks the PHY connection logic because
the PHY name still uses the old bus names "0" and "1", fix that to
always use the mdio bus id instead.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The first parameter should be "number of elements" and the second parameter
should be "element size".
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>