Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>

The patch extends card_detect and write_protect support to get mx5
family and more scenarios supported.  The changes include:

 * Turn platform_data from optional to mandatory
 * Add cd_types and wp_types into platform_data to cover more use
   cases
 * Remove the use of flag ESDHC_FLAG_GPIO_FOR_CD
 * Adjust some machine codes to adopt the platform_data changes
 * Work around the issue that software reset will get card detection
   circuit stop working

With this patch, card_detect and write_protect gets supported on
mx5 based platforms.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Tested-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: NChris Ball <cjb@laptop.org>

The patch makes necessary changes on gpio-mxc as below to turn it
into an upstanding gpio driver.

 * Add a list to save all mx2 ports references, so that
   mx2_gpio_irq_handler can walk through all interrupt status
   registers

 * Use readl/writel to replace mach-specific accessors
   __raw_readl/__raw_writel

 * Change mxc_gpio_init into mxc_gpio_probe function

 * Move "struct mxc_gpio_port" into gpio-mxc.c, as it needs not to
   be public at all, and also make some other cleanup on
   plat-mxc/include/mach/gpio.h at the same time

And the patch then migrates mach-imx and mach-mx5 to the updated
driver by adding corresponding platform devices.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Fixing a few "please, no space before tabs" and "empty line at end of
file" warnings on the way.

LAKML-Reference: 1299271882-2130-6-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

... together with the related devices "mx3_camera" and "mx3_sdc_fb".

"mx3_camera" doesn't fit the scheme of the other devices that just are
allocated and registered in a single function because it needs additional
care to get some dmaable memory. So currently imx31_alloc_mx3_camera
duplicates most of imx_add_platform_device_dmamask, but I'm not sure it's
worth to split the latter to be able to reuse more code.

This gets rid of mach-mx3/devices.[ch] and so several files need to be
adapted not to #include devices.h anymore.

LAKML-Reference: 1299271882-2130-5-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Most machine files include "devices-imxXX.h" which in turn includes
<mach/devices-common.h>.  The latter already includes many headers
that the machine files don't need to include again.

These were found by:

 $ grep \#include arch/arm/plat-mxc/include/mach/devices-common.h > tmpfile
 $ git grep -l 'devices-imx' arch/arm | xargs grep -f tmpfile -F

(but I kept linux/init.h, linux/kernel.h and linux/platform_device.h)

LAKML-Reference: 1298912674-15153-2-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The boards are currently using otg_ulpi_create and mxc_ulpi_access_ops,
both are only present if CONFIG_USB_ULPI is set. To remove the need of
ifdefs in the board code introduce a imx_otg_ulpi_create functions
which expands to a static inline function if compiled without ulpi.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The latter are error-prone because the bank number is one less than one
would read in the documentation.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NEric Benard <eric@eukrea.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

mxc_board_init is too generic to be useful.  Additionally change some
mxc_timer to ${machine}_timer, too.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The mxc-ehci driver calls SoC specific phy initialization right after
calling board specific initialization. To offer greater flexibility for
boards to setup the phy and to get rid of some unnecessary flags in
platform data this patch lets the boards call the SoC specific phy
initialization and remove it from the driver.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The usbh1 port of the pcm043 does not use ulpi, so put it outside
the corresponding ifdefs.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch actually replaces the 'struct pad_desc' with a u64 cookie
to facilitate adding platform specific pad_ctrl settings to an
existing pad definition.

So, instead of:
	iomux_v3_cfg_t power_key = MX51_PAD_EIM_A27__GPIO_2_21;
	power_key.pad_ctrl = MX51_GPIO_PAD_CTRL_2;
	mxc_iomux_v3_setup_pad(&power_key);
one can write:
	mxc_iomux_v3_setup_pad((MX51_PAD_EIM_A27__GPIO_2_21 & ~MUX_PAD_CTRL_MASK) | MX51_GPIO_PAD_CTRL_2);

Patch applies to branch 'imx-for-2.6.38' of git://git.pengutronix.de/git/imx/linux-2.6Signed-Off-By: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The following patch is a first step to convert the 'struct pad_desc'
to a bitmapped cookie to facilitate adding platform specific pullup or
drive strength definitions to existing pad definitions without need to
rewrite the complete pad def.

The patch wraps 'struct pad_desc' in an opaque data type and
introduces macros to access the individual members.
This patch does not constitute any functional change!
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

and restore alphabetic ordering.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

While adapting the #defines for this I noticed that the offset
used for USB HS on i.MX35 differs from the documented offset.
I kept the working offset and commented that the documentation
differs.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.

The various declarations were removed using the following script:

  grep -rl MACHINE_START arch/arm | xargs \
  sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'

[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>

Tested on i.MX25 and i.MX35 and i.MX51
Signed-off-by: NEric Bénard <eric@eukrea.com>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

1) Introduce ulpi specific flags for control of the ulpi phy
2) Extend the generic ulpi driver with support for Function and
Interface control of upli phy
3) Update the platforms using the generic ulpi driver with new ulpi
flags
4) Remove the otg control flags not in use
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Like this one (if CONFIG_USB_ULPI is not set):

arch/arm/mach-mx3/mach-pcm043.c:312: warning: 'otg_pdata' defined but not used
arch/arm/mach-mx3/mach-pcm043.c:317: warning: 'usbh1_pdata' defined but not used
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Make use of new mechanism to register a nand device.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

As the kernel contains a copy of the GPL anyhow just get rid of the address
specification instead of fixing it.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This is a further step in allowing to build a kernel image for more
than one imx SOC.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

While at it remove some superfluous parenthesis.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>

This just leaves cpu.c, devices.c and mm.c to clean up.  As these files
are used on more than one SOC they need some more work.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Guennadi Liakhovetski <lg@denx.de>
Cc: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Harro Haan <hrhaan@yahoo.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Luotao Fu <l.fu@pengutronix.de>
Cc: Ilya Yanok <yanok@emcraft.com>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NLuotao Fu <l.fu@pengutronix.de>