TIF_NOTIFY_RESUME added (as bit 5).  That way nommu glue needs no changes at
all; mmu one needs just to replace jmi do_signal_return to jne do_signal_return
There we have flags shifted up, until bit 6 (SIGPENDING) is in MSBit; instead
of checking that MSBit is set (jmi) we check that MSBit or something below it
is set (jne); bits 0..4 are never set, so that's precisely "bit 6 or bit 5 is
set".

Usual handling of NOTIFY_RESUME/SIGPENDING is done in do_notify_resume(); glue
calls it instead of do_signal().
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

The changes in the mmu version of entry.h (entry_mm.h) and the non-mmu
version (entry_no.h) are not about the presence or use of an MMU at all.
The main changes are to support the ColdFire processors. The code for
trap entry and exit for all types of 68k processor outside coldfire is
the same.

So merge the files back to a single entry.h and share the common 68k
entry/exit code. Some changes are required for the non-mmu entry
handlers to adopt the differing macros for system call and interrupt
entry, but this is quite strait forward. The changes for the ColdFire
remove a couple of instructions for the separate a7 register case, and
are no worse for the older single a7 register case.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

commit 2502b667 ("Change the m68knommu irq
handling to use the generic irq framework.") removed the reporting of spurious
interrupts on nommu (68328 and 68360).

Bring it back in a generic way, using "atomic_t irq_err_count", as that's what
most of the other architectures are using.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The non-MMU m68k targets can use the same asm/system.h as the MMU
targets. So switch the current system_mm.h to be system.h and remove
system_no.h.

The assembly support code for the non-MMU resume functions needs to
be modified to match the now common switch_to() macro. Specifically
this means correctly saving and restoring the status flags in the case
of the ColdFire resume, and some reordering of the code to not use
registers before they are saved or after they are restored.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

It is strait forward to merge the mmu and non-mmu versions of
asm-offstes.c. Some name changes are required for the preempt and
thread_info.flags in the non-mmu entry.S assembler to make them
consistent for both setups.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

There is a lot of common code that could be shared between the m68k
and m68knommu arch branches. It makes sense to merge the two branches
into a single directory structure so that we can more easily share
that common code.

This is a brute force merge, based on a script from Stephen King
<sfking@fdwdc.com>, which was originally written by Arnd Bergmann
<arnd@arndb.de>.

> The script was inspired by the script Sam Ravnborg used to merge the
> includes from m68knommu. For those files common to both arches but
> differing in content, the m68k version of the file is renamed to
> <file>_mm.<ext> and the m68knommu version of the file is moved into the
> corresponding m68k directory and renamed <file>_no.<ext> and a small
> wrapper file <file>.<ext> is used to select between the two version. Files
> that are common to both but don't differ are removed from the m68knommu
> tree and files and directories that are unique to the m68knommu tree are
> moved to the m68k tree. Finally, the arch/m68knommu tree is removed.
>
> To select between the the versions of the files, the wrapper uses
>
> #ifdef CONFIG_MMU
> #include <file>_mm.<ext>
> #else
> #include <file>_no.<ext>
> #endif

On top of this file merge I have done a simplistic merge of m68k and
m68knommu Kconfig, which primarily attempts to keep existing options and
menus in place. Other than a handful of options being moved it produces
identical .config outputs on m68k and m68knommu targets I tested it on.

With this in place there is now quite a bit of scope for merge cleanups
in future patches.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The _TIF_WORK_MASK definition was removed in the clean up of MMU and
non-MMU arch/m68k/include/asm/thread_info*.h files (this was commit
cddafa35, "merge MMU and non-MMU
thread_info.h").

It didn't get cleaned out of the entry.S code for the 68328 and 68360
based platforms. And it was replaced by a hard coded constant mask for
coldfire platforms. There is currently no need to mask any of these bits,
so fix all uses (and former uses) to check for any non-zero value.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

we shouldn't bugger off to userland when there still are
pending signals; among other things it makes e.g. SIGSEGV
triggered by failure to build a sigframe to be delivered
_now_ and not when we hit the next syscall or interrupt.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>

Break up syscall_trace() into separate entry and exit routines that use
tracehook_report_syscall_entry() and tracehook_report_syscall_exit().
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

In m68k/m68knommu assembly files, the same value is called sometimes
PT_OFF_VECTOR, but more frequently PT_OFF_FORMATVEC.  Standardize
name to PT_OFF_FORMATVEC.
Signed-off-by: NPhilippe De Muyter <phdm@macqel.be>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Signed-off-by: NPhilippe De Muyter <phdm@macqel.be>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

strace enabled is marked using the `flags' field of the `thread_info' struct.
68360 version of entry.S did test a wrong bit in a wrong structure
(task_struct).

68328 version of entry.S did test the right bit in the right structure,
but wrongly, because the `flags' field is 32 bit wide, while the used
assembler insn (btst) only accesses a 8 bit byte in memory.

Fix both using code already used in the coldfire version of entry.S
Signed-off-by: NPhilippe De Muyter <phdm@macqel.be>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Commit f159ee78 ("locking,
m68k/asm-offsets: Rename pt_regs offset defines") breaks the
m68knommu entry code that relies on these define names.
Fix the files to match the new define names.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Change the m68knommu irq handling to use the generic irq framework.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

Use the THREAD_SIZE define when manipulating the stack instead of
hard coded values (for the 68328 and 68360 sub-architectures).
Signed-off-by: NGreg Ungerer <gerg@uclinux.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!