The device.h header was including module.h, making it present for
most of these drivers.  But we want to clean that up.  Call out the
include of module.h in the modular network drivers.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Moves the Intel wired LAN drivers into drivers/net/ethernet/intel/ and
the necessary Kconfig and Makefile changes.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some minor comment errors and whitespace issues discovered while looking
into this are also addressed.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Correct error messages when setting up Rx resources and when checking
module parameters.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Most e1000e parts support batching writebacks.  The problem with this is
that when some of the TADV or TIDV timers are not set, Tx can sit forever.

This is solved in this patch with write flushes using the Flush Partial
Descriptors (FPD) bit in TIDV and RDTR.

This improves bus utilization and removes partial writes on e1000e,
particularly from 82571 parts in S5500 chipset based machines.

Only ES2LAN and 82571/2 parts are included in this optimization, to reduce
testing load.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As requested by Dave Miller.  A follow-on set of patches will allow for
ethtool to enable/disable the feature instead.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables IEEE802.3az (a.k.a. Energy Efficient Ethernet) on the
new 82579 LOMs.  An optional module parameter is provided to disable the
feature if desired.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A couple stack cleanups missed in an earlier patch from Jesse.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Back before e1000-7.3.20, the e1000 driver had a simple algorithm that
managed interrupt moderation.  The driver was updated in 7.3.20 to
have the new "adaptive" interrupt moderation but we have customer
requests to redeploy the old way as an option.  This patch adds the
old functionality back.  The new functionality can be enabled via
module parameter or at runtime via ethtool.
Module parameter: (InterruptThrottleRate=4) to use this new
moderation method.
Ethtool method: ethtool -C ethX rx-usecs 4
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

used a modified checkstack to get the 56 number
(normally checkstack wouldn't show this low a value)

checkstack before:
0x0000012f e1000e_check_options [e1000e]:               272

after:
0x0000012f e1000e_check_options [e1000e]:                56
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CRC stripping should be enabled by default but was not if it was not
specified as a module parameter.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some users reported that they have machines with BMCs enabled that cannot
receive IPMI traffic after e1000e is loaded.
http://marc.info/?l=e1000-devel&m=121909039127414&w=2
http://marc.info/?l=e1000-devel&m=121365543823387&w=2

This fixes the issue if they load with the new parameter = 0 by disabling
crc stripping, but leaves the performance feature on for most users.
Based on work done by Hong Zhang.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the hardware to ignore all write/erase cycles to the GbE region in
the ICHx NVM.  This feature can be disabled by the WriteProtectNVM module
parameter (enabled by default) only after a hardware reset, but
the machine must be power cycled before trying to enable writes.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
CC: arjan@linux.intel.com
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This new part has the same feature set as previous parts with the addition
of MSI-X support.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The removal of this bit of code was missed in an earlier patch submittal.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

During module load, seting the InterruptThrottleRate parameter to an
invalid value would result in the itr/itr_setting pair being set to
unexpected values which would result in poor performance.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The ndev_* printk's are too lenghty and we don't need to specify
the adapter/netdev struct at all, making this a lot more readable.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Adjusting the comment blocks here to be code-style compliant. no
code changes.

Changed some copyright dates to 2008.

Indentation fixes.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

L1 ASPM link (pci-e link power savings) has significant benefits
(~1W savings when link is active) but unfortunately does not work
correctly on any of the chipsets that have 82573 on mobile platforms
which causes various nuisances:
 - eeprom reads return garbage information leading to bad eeprom
   checksums
 - long ping times (up to 2 seconds)
 - complete system hangs (freeze/lockup)

A lot of T60 owners have been plagued by this, but other mobile
solutions also suffer from these symptoms.

Disabling L1 ASPM before we activate the PCI-E link fixes all of
these issues at the cost of some power consumption.

Remove a workaround RDTR adjustment that is no longer needed with
this new one.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix sparse warnings from e1000e driver in net-2.6.24.

Added a sparse fix for module param arrays which can have int values
but only the array index needs to be unsigned. --Auke
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This driver implements support for the ICH9 on-board LAN ethernet
device. The device is similar to ICH8.

The driver encompasses code to support 82571/2/3, es2lan and ICH8
devices as well, but those device IDs are disabled and will be
"lifted" from the e1000 driver over one at a time once this driver
receives some more live time.

Changes to the last snapshot posted are exclusively in the internal
hardware API organization. Many thanks to Jeff Garzik for jumping in
and getting this organized with a keen eye on the future layout.

[ Integrated napi_struct patch from Auke as well... -DaveM ]
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>