According Documentation/timers/timers-howto.txt the usually case for
setting up a hrtimer takes > ~10us. So we should use udelay in this
case so we are sure that the state change was done, before doing the
state change assert.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

There is no need to use the safe version of list_for_each here.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

btusb currently has a generic match on USB device descriptors:
        { USB_DEVICE_INFO(0xe0, 0x01, 0x01) },

However, http://www.usb.org/developers/defined_class states:

  Base Class E0h (Wireless Controller)
  This base class is defined for devices that are Wireless controllers.
  Values not shown in the table below are reserved. These class codes are
  to be used in Interface Descriptors, with the exception of the Bluetooth
  class code which can also be used in a Device Descriptor.

Add a match on the interface descriptors accordingly.

This fixes compatibility with the RTL8723AU device shown below.
This device conforms to the USB Interface Association Descriptor
specification, which requires the device to have class ef/02/01.
The extra IAD descriptor then specifies that interfaces 0 and 1
belong to the same function/driver, which is true. Provided that
the Bluetooth device class spec accepts use of the IAD, I imagine that
technically, all btusb devices should be configured like this.

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0bda ProdID=0724 Rev= 2.00
S:  Manufacturer=Realtek
S:  Product=802.11n WLAN Adapter
S:  SerialNumber=00e04c000001
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 4 Cls=ff(vend.) Sub=ff Prot=ff Driver=rtl8723au
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=03(Int.) MxPS=  64 Ivl=500us
Signed-off-by: NDaniel Drake <drake@endlessm.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

To avoid amp module hooks from hci_event.c
Signed-off-by: NArron Wang <arron.wang@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

To avoid amp module hooks from hci_event.c
Signed-off-by: NArron Wang <arron.wang@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

To avoid a2mp module hooks from hci_event.c and send
getinfo response operation only required by a2mp module,
we can move this callback to a2mp.c
Signed-off-by: NArron Wang <arron.wang@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Signed-off-by: NArron Wang <arron.wang@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Move A2MP Module under BT_HS config option and allow
the user have flexible option to choose the feature only
they need

a2mp_discover_amp() & a2mp_channel_create() are a2mp module
entry point for master and slave, and this is dynamic
invoked depends on the userspace or remote request, then
we defined their implementation depends on BT_HS config
Signed-off-by: NArron Wang <arron.wang@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add "waiting for configuration" address.
Add lmp_subver and firmware name for BCM4330B1 controller.
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Cleanedup "Unnecessary space before function pointer arguments" warning
reported by Checkpatch
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Fix for Cleanpatch warning:
Space prohibited between function name and open parenthesis '('
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Fix for "Unnecessary space before function pointer arguments" reported
by checkpatch.
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Move IRK checking logic in preparation to new connect method. Also
make sure that MGMT_STATUS_INVALID_PARAMS is returned when non
identity address is passed to ADD_DEVICE. Right now MGMT_STATUS_FAILED
is returned, which might be misleading.
Signed-off-by: NJakub Pawlowski <jpawlowski@google.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Slave latency range has been changed in Core Spec. 4.2 by Erratum 5419
of ESR08_V1.0.0. And it should be applied to Core Spec. 4.0 and 4.1.

Before:
   connSlaveLatency <= ((connSupervisionTimeout / connIntervalMax) - 1)

After:
   connSlaveLatency <= ((connSupervisionTimeout / (connIntervalMax*2)) - 1)

This patch makes hci_check_conn_params() check the allowable slave
latency range using the changed way.
Signed-off-by: NSeungyoun Ju <sy39.ju@samsung.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

In ancient times it was necessary to manually initialize the bus
field of an spi_driver to spi_bus_type. These days this is done in
spi_register_driver(), so we can drop the manual assignment.
Signed-off-by: NAntonio Borneo <borneo.antonio@gmail.com>
Acked-by: NVarka Bhadram <varkabhadram@gmail.com>
Acked-by: NAlan Ott <alan@signal11.us>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add a timeout to prevent the do while loop running in an
infinite loop. This ensures that the channel will be
instructed to close within 10 seconds so prevents
l2cap_sock_shutdown() getting stuck forever.

Returns -ENOLINK when the timeout is reached. The channel
will be subequently closed and not all data will be ACK'ed.
Signed-off-by: NDean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Use msecs_to_jiffies() instead of using HZ so that it
is easier to specify the time in milliseconds.

Also add a #define L2CAP_WAIT_ACK_POLL_PERIOD to specify the 200ms
polling period so that it is defined in a single place.
Signed-off-by: NDean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add helpful BT_DBG debug to l2cap_sock_shutdown()
and __l2cap_wait_ack() so that the code flow can
be analysed.
Signed-off-by: NDean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Use chan->state instead of chan->conn because waiting
for ACK's is only possible in the BT_CONNECTED state.
Also avoids reference to the conn structure so makes
locking easier.

Only call __l2cap_wait_ack() when the needed condition
of chan->unacked_frames > 0 && chan->state == BT_CONNECTED
is true and convert the while loop to a do while loop.

__l2cap_wait_ack() change the function prototype to
pass in the chan variable as chan is already available
in the calling function l2cap_sock_shutdown(). Avoids
locking issues.
Signed-off-by: NDean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

During execution of l2cap_sock_shutdown() which might
sleep, the sk and chan structures can be in an unlocked
condition which potentially allows the structures to be
freed by other running threads. Therefore, there is a
possibility of a malfunction or memory reuse after being
freed.

Keep the sk and chan structures alive during the
execution of l2cap_sock_shutdown() by using their
respective hold and put functions. This allows the structures
to be freeable at the end of l2cap_sock_shutdown().
Signed-off-by: NKautuk Consul <Kautuk_Consul@mentor.com>
Signed-off-by: NDean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Instead of passing ieee802154_hw pointer to ieee802154_rx,
we can directly pass the ieee802154_local pointer.
Signed-off-by: NVarka Bhadram <varkabhadram@gmail.com>
Acked-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Right now there are no other users for ieee802154_rx()
in kernel. So lets remove EXPORT_SYMBOL() for this.

Also it moves the function prototype from global header
file to local header file.
Signed-off-by: NVarka Bhadram <varkabhadram@gmail.com>
Acked-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Remove semicolon in switch statement, reported by coccinelle
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Intel version information is shared between USB and UART drivers
and with that move it into a generic function of the Intel module.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The Intel Secure Send command is used the same in USB and UART drivers
and with that move a generic version into the Intel module.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The Intel specific Bluetooth module provides support for pubic address
configuration. So make sure that it is enabled for Intel UART devices.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The Intel specific Bluetooth module provides now an exported function
for the hardware error. Use that instead of duplicating it inside the
driver.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The handling of hardware error has support for providing a vendor
specific callback to deal with the error. Move the Intel specific
function out of the USB driver into the generic module so that it
can also be utilized by the UART driver.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Removed semicolon at end of switch statement,error reported by Coccinelle
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Removed semicolon at the end of switch case statement
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Intel Lightning Peak devices do not come with Bluetooth firmware
loaded and thus require a full download of the operational Bluetooth
firmware when the device is attached via the Bluetooth line discipline.

Lightning Peak devices start with a bootloader mode that only accepts
a very limited set of HCI commands. The supported commands are enough
to identify the hardware and select the right firmware to load.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch introduces suspend and resume callbacks to mac802154. When
doing suspend we calling the stop driver callback which should stop the
receiving of frames. A transceiver should go into low-power mode then.
Calling resume will call the start driver callback, which starts receiving
again and allow to transmit frames.

This was tested only with the fakelb driver and a qemu vm by doing the
following commands:

echo "devices" > /sys/power/pm_test
echo "freeze" > /sys/power/state

while doing some high traffic between two fakelb phys.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch help to implement suspend/resume in mac802154, these
hooks will be run before the device is suspended and after it
resumes.
Signed-off-by: NVarka Bhadram <varkab@cdac.in>
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds ieee802154_stop_device for preparing a utility function
to stop the ieee802154 device.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch removes the unused macro which was removed
with the rework of linux-wpan kernel.
Signed-off-by: NVarka Bhadram <varkab@cdac.in>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch will generate the warning if the required driver ops
were not defined. Also it removes unnecessary debug message.
Signed-off-by: NVarka Bhadram <varkab@cdac.in>
Acked-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The iphc module depends on CONFIG_IPV6, because it's not very useful to
build the module without IPv6 support. Recently an user reported about
issues for setting an IPv6 address to a 6LoWPAN interface. The issues
was solved by modprobe the ipv6 module before. To avoid such user issues
we try to request the ipv6 module when the 6LoWPAN module is loaded.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Acked-by: NJukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds a workaround for using the new nl802154 netlink
interface with the old ieee802154 netlink interface togehter. The
nl802154 currently supports no access for llsec layer, currently there
are users outside which are using both interfaces at the same time. This
patch adds a necessary call when addresses are updated.
Reported-by: NSimon Vincent <simon.vincent@xsilon.com>
Suggested-by: NPhoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Braces {} are not necessary for single statement blocks reported by
checkpatch
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Convert the module_init() to a invocation from inet_init() since
ip_tunnel_core is part of the INET built-in.

Fixes: 3093fbe7 ("route: Per route IP tunnel metadata via lightweight tunnel")
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>