The default number of maximum channels should be limited to the
number of cpus available on the numa node of the primary channel.
This also makes sure maximum channels <= num_online_cpus
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If device is not up, then changing MTU (or number of channels)
should not re-enable the device.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using NAPI, the single stream performance declined signifcantly
because the poll routine was updating host after every burst
of packets. This excess signalling caused host throttling.

This fix restores the old behavior. Host is only signalled
after the ring has been emptied.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If there are no egress packets pending, then don't look for tx completions
in napi poll.  Also, fix broken tx queue wakeup logic.
Signed-off-by: NVSR Burru <veerasenareddy.burru@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NSatanand Burla <satananda.burla@cavium.com>
Signed-off-by: NDerek Chickles <derek.chickles@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add workqueue that is periodically run to try to allocate RX buffers in OOM
conditions in PF and VF.
Signed-off-by: NSatanand Burla <satananda.burla@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Iyappan Subramanian says:

====================
drivers: net: xgene-v2: Add MDIO and ethtool support

This patch set,

- adds phy management and ethtool support
- fixes ethernet reset
- addresses review comments from previous patch set

v2: Address review comments from v1
	- removed mdio_lock, since there is a top level lock in mdio_bus.c

v1:
	- Initial version
====================
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed review comments from the previous patch-set.

- changed return value check of platform_get_irq() to < 0
- replaced devm_request(free)_irq() calls by request(free)_irq() since
  they are called from open() and close()
- changed sizeof(struct mystruct) to sizeof(*mystruct)
- reduced indentation on tx_timeout()
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed port reset sequence by adding ECC init.
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added basic ethtool support.
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added phy management support by using phy abstraction layer APIs.
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Martin KaFai Lau says:

====================
bpf: Add map-in-map support

This patchset adds map-in-map support (map->map).
One use case is the (vips -> webservers) in the L4 load balancer so
that different vips can be backed by different set of webservers.

Please refer to the individual commit log for details.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Test cases for array of maps and hash of maps.
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds hash of maps support (hashmap->bpf_map).
BPF_MAP_TYPE_HASH_OF_MAPS is added.

A map-in-map contains a pointer to another map and lets call
this pointer 'inner_map_ptr'.

Notes on deleting inner_map_ptr from a hash map:

1. For BPF_F_NO_PREALLOC map-in-map, when deleting
   an inner_map_ptr, the htab_elem itself will go through
   a rcu grace period and the inner_map_ptr resides
   in the htab_elem.

2. For pre-allocated htab_elem (!BPF_F_NO_PREALLOC),
   when deleting an inner_map_ptr, the htab_elem may
   get reused immediately.  This situation is similar
   to the existing prealloc-ated use cases.

   However, the bpf_map_fd_put_ptr() calls bpf_map_put() which calls
   inner_map->ops->map_free(inner_map) which will go
   through a rcu grace period (i.e. all bpf_map's map_free
   currently goes through a rcu grace period).  Hence,
   the inner_map_ptr is still safe for the rcu reader side.

This patch also includes BPF_MAP_TYPE_HASH_OF_MAPS to the
check_map_prealloc() in the verifier.  preallocation is a
must for BPF_PROG_TYPE_PERF_EVENT.  Hence, even we don't expect
heavy updates to map-in-map, enforcing BPF_F_NO_PREALLOC for map-in-map
is impossible without disallowing BPF_PROG_TYPE_PERF_EVENT from using
map-in-map first.
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a few helper funcs to enable map-in-map
support (i.e. outer_map->inner_map).  The first outer_map type
BPF_MAP_TYPE_ARRAY_OF_MAPS is also added in this patch.
The next patch will introduce a hash of maps type.

Any bpf map type can be acted as an inner_map.  The exception
is BPF_MAP_TYPE_PROG_ARRAY because the extra level of
indirection makes it harder to verify the owner_prog_type
and owner_jited.

Multi-level map-in-map is not supported (i.e. map->map is ok
but not map->map->map).

When adding an inner_map to an outer_map, it currently checks the
map_type, key_size, value_size, map_flags, max_entries and ops.
The verifier also uses those map's properties to do static analysis.
map_flags is needed because we need to ensure BPF_PROG_TYPE_PERF_EVENT
is using a preallocated hashtab for the inner_hash also.  ops and
max_entries are needed to generate inlined map-lookup instructions.
For simplicity reason, a simple '==' test is used for both map_flags
and max_entries.  The equality of ops is implied by the equality of
map_type.

During outer_map creation time, an inner_map_fd is needed to create an
outer_map.  However, the inner_map_fd's life time does not depend on the
outer_map.  The inner_map_fd is merely used to initialize
the inner_map_meta of the outer_map.

Also, for the outer_map:

* It allows element update and delete from syscall
* It allows element lookup from bpf_prog

The above is similar to the current fd_array pattern.
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix in verifier:
For the same bpf_map_lookup_elem() instruction (i.e. "call 1"),
a broken case is "a different type of map could be used for the
same lookup instruction". For example, an array in one case and a
hashmap in another.  We have to resort to the old dynamic call behavior
in this case.  The fix is to check for collision on insn_aux->map_ptr.
If there is collision, don't inline the map lookup.

Please see the "do_reg_lookup()" in test_map_in_map_kern.c in the later
patch for how-to trigger the above case.

Simplifications on array_map_gen_lookup():
1. Calculate elem_size from map->value_size.  It removes the
   need for 'struct bpf_array' which makes the later map-in-map
   implementation easier.
2. Remove the 'elem_size == 1' test

Fixes: 81ed18ab ("bpf: add helper inlining infra and optimize map_array lookup")
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dma operation mode configuration routine was wrongly moved to a
function (stmmac_mtl_configuration) that is only executed if the
core version is >= 4.00.

Fixes: 6deee222 ("net: stmmac: prepare dma op mode config for multiple queues")
Reported-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: NThierry Reding <thierry.reding@gmail.com>
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Tested-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit adds a new sysctl accept_ra_rt_info_min_plen that
defines the minimum acceptable prefix length of Route Information
Options. The new sysctl is intended to be used together with
accept_ra_rt_info_max_plen to configure a range of acceptable
prefix lengths. It is useful to prevent misconfigurations from
unintentionally blackholing too much of the IPv6 address space
(e.g., home routers announcing RIOs for fc00::/7, which is
incorrect).
Signed-off-by: NJoel Scherpelz <jscherpelz@google.com>
Acked-by: NLorenzo Colitti <lorenzo@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: allow concurrency in core and minor fixes

The first 10 patches of this series prepare nfpcore for concurrent
accesses.  This will be needed by upcoming hwmon and devlink patches.
Most locking is already in place, the patches in this series iron out
a few bugs.

Last 5 patches are fixes and cleanups to the netdev code, including
removal of doorbell pointers used only on old versions of the chip,
removal of unnecessarily defensive code and flushing xmit_more more
carefully on error paths.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we no longer need to keep the FW enabled for .ndo_close()
to work we can always stop FW after reconfiguration failure.
This seems to make most FWs more resilient to faults (at least
in error injection scenarios).
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device open and close handlers check if the device is already
in the desired state.  Thanks to our reconfig infrastructure
this should not be necessary, there doesn't seem to be any
code in the driver which depends on it.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of ring full or DMA mapping error remember to flush xmit_more
delayed kicks.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NFP6000 doesn't use queue pointers/doorbells for RX, it uses
'done' bit in descriptors.  Remove the pointers from data structures.
Since we are saving space in rx_ring structure make fields we
previously compressed to 16bits word size again.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix warning which was using netdev_warn() instead of dev_warn()
to early.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When acquiring an area fails we can't call function doing both
release and free.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Core should detect when someone is trying to request an access
window which is too large for a given type of access.  Otherwise
the requester will be put on a wait queue for ever without any
error message.

Add const qualifiers to clarify that we are only looking at read-
-only members in relevant functions.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When signal interrupts waiting for an area to become available
we assume success.  Pay attention to the return code.  Unpack
the code a little bit to make it more readable.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

msleep_interruptible() returns time left to wait, not error
code.  Return ERESTARTSYS when interrupted.

While at it correct a comment and make the polling a bit
more aggressive.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We shouldn't access area_cache_list without its lock even
to check if it's empty.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Document which fields of nfp_cpp are protected by which locks.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After mutex cache removal we can put the mutex code in a separate
source file.  This makes it clear it doesn't play with internals
of struct nfp_cpp any more.

No functional changes.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CPP mutex cache was introduced to work around the fact that the
same host could successfully acquire a lock multiple times.  It
used to collapse multiple users to the same struct nfp_cpp_mutex
and track use count.  Unfortunately it's racy.  Since we now force
all nfp_mutex_lock() callers within the host to actually succeed
at acquiring the lock we no longer need the cache, let's remove it.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The global device lock is acquired to search the resource table.
The lock is actually itself part of the table (entry 0).
Therefore if someone asks for resource 0 we would deadlock since
double locking is no longer allowed.

Currently the driver doesn't try to lock that resource so let's
simply make sure we fail graciously and not add special handling
of this case until really need.  Hide the relevant defines in
the source file.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NFP can be connected to multiple machines via PCI or other buses.
Access to hardware resources is arbitrated using locks residing
in device memory.  Currently nfpcore only respects the mutexes
when it comes to inter-host locking, but if we try to acquire
the same lock again, on one host - it will simply return success
because owner of the lock is already set to that host.

This makes the locks useless for arbitration within one host
and unfair because whichever host grabbed the lock will have
a chance to reacquire it without others getting a shot.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dma_mapping_error() returns true if there is an error but we want
to return -ENOMEM and not 1.

Fixes: 65e0ace2 ("net: dwc-xlgmac: Initial driver for DesignWare Enterprise Ethernet")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NJie Deng <jiedeng@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the rtnl_dump_all to dump all netconf handlers that have been
registered. Allows userspace to send a dump request for PF_UNSPEC
and get all families.

Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Russell King says:

====================
Clean up PHY MMD accessors

This series cleans up phylib's MMD accessors, so that we have a common
way of accessing the Clause 45 register set.

The current situation is far from ideal - we have phy_(read|write)_mmd()
which accesses Clause 45 registers over Clause 45 accesses, and we have
phy_(read|write)_mmd_indirect(), which accesses Clause 45 registers via
Clause 22 register 13/14.

Generic code uses the indirect methods to access standard Clause 45
features, and when we come to add Clause 45 PHY support to phylib, we
would need to make these conditional upon the PHY type, or duplicate
these functions.

An alternative solution is to merge these accessors together, and select
the appropriate access method depending upon the 802.3 clause that the
PHY conforms with.  The result is that we have a single set of
phy_(read|write)_mmd() accessors.

For cases which require special handling, we still allow PHY drivers to
override all MMD accesses - except rather than just overriding the
indirect accesses.  This keeps existing overrides working.

Combining the two also has another beneficial side effect - we get rid
of similar functions that take arguments in different orders.  The
old direct accessors took the phy structure, devad and register number,
whereas the indirect accessors took the phy structure, register number
and devad in that order.  Care must be taken when updating future
drivers that the argument order is correct, and the function name is
not merely replaced.

This patch set is against net-next.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make mmd_phy_indirect() use the same terminology as the rest of the
code, making clear what each address is - phy address, devad, and
register number.

While here, remove the "inline" from this static function, leaving
it to the compiler to decide whether to inline this function, and
get rid of unnecessary parens.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the indirect MMD read/write methods which are now no longer
necessary.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>