Removed semicolon at end of switch statement,error reported by Coccinelle
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Removed semicolon at the end of switch case statement
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Intel Lightning Peak devices do not come with Bluetooth firmware
loaded and thus require a full download of the operational Bluetooth
firmware when the device is attached via the Bluetooth line discipline.

Lightning Peak devices start with a bootloader mode that only accepts
a very limited set of HCI commands. The supported commands are enough
to identify the hardware and select the right firmware to load.
Signed-off-by: NLoic Poulain <loic.poulain@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch introduces suspend and resume callbacks to mac802154. When
doing suspend we calling the stop driver callback which should stop the
receiving of frames. A transceiver should go into low-power mode then.
Calling resume will call the start driver callback, which starts receiving
again and allow to transmit frames.

This was tested only with the fakelb driver and a qemu vm by doing the
following commands:

echo "devices" > /sys/power/pm_test
echo "freeze" > /sys/power/state

while doing some high traffic between two fakelb phys.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch help to implement suspend/resume in mac802154, these
hooks will be run before the device is suspended and after it
resumes.
Signed-off-by: NVarka Bhadram <varkab@cdac.in>
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds ieee802154_stop_device for preparing a utility function
to stop the ieee802154 device.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch removes the unused macro which was removed
with the rework of linux-wpan kernel.
Signed-off-by: NVarka Bhadram <varkab@cdac.in>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch will generate the warning if the required driver ops
were not defined. Also it removes unnecessary debug message.
Signed-off-by: NVarka Bhadram <varkab@cdac.in>
Acked-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The iphc module depends on CONFIG_IPV6, because it's not very useful to
build the module without IPv6 support. Recently an user reported about
issues for setting an IPv6 address to a 6LoWPAN interface. The issues
was solved by modprobe the ipv6 module before. To avoid such user issues
we try to request the ipv6 module when the 6LoWPAN module is loaded.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Acked-by: NJukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds a workaround for using the new nl802154 netlink
interface with the old ieee802154 netlink interface togehter. The
nl802154 currently supports no access for llsec layer, currently there
are users outside which are using both interfaces at the same time. This
patch adds a necessary call when addresses are updated.
Reported-by: NSimon Vincent <simon.vincent@xsilon.com>
Suggested-by: NPhoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Braces {} are not necessary for single statement blocks reported by
checkpatch
Signed-off-by: NPrasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Convert the module_init() to a invocation from inet_init() since
ip_tunnel_core is part of the INET built-in.

Fixes: 3093fbe7 ("route: Per route IP tunnel metadata via lightweight tunnel")
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	net/bridge/br_mdb.c

br_mdb.c conflict was a function call being removed to fix a bug in
'net' but whose signature was changed in 'net-next'.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Don't use shared bluetooth antenna in iwlwifi driver for management
    frames, from Emmanuel Grumbach.

 2) Fix device ID check in ath9k driver, from Felix Fietkau.

 3) Off by one in xen-netback BUG checks, from Dan Carpenter.

 4) Fix IFLA_VF_PORT netlink attribute validation, from Daniel Borkmann.

 5) Fix races in setting peeked bit flag in SKBs during datagram
    receive.  If it's shared we have to clone it otherwise the value can
    easily be corrupted.  Fix from Herbert Xu.

 6) Revert fec clock handling change, causes regressions.  From Fabio
    Estevam.

 7) Fix use after free in fq_codel and sfq packet schedulers, from WANG
    Cong.

 8) ipvlan bug fixes (memory leaks, missing rcu_dereference_bh, etc.)
    from WANG Cong and Konstantin Khlebnikov.

 9) Memory leak in act_bpf packet action, from Alexei Starovoitov.

10) ARM bpf JIT bug fixes from Nicolas Schichan.

11) Fix backwards compat of ANY_LAYOUT in virtio_net driver, from
    Michael S Tsirkin.

12) Destruction of bond with different ARP header types not handled
    correctly, fix from Nikolay Aleksandrov.

13) Revert GRO receive support in ipv6 SIT tunnel driver, causes
    regressions because the GRO packets created cannot be processed
    properly on the GSO side if we forward the frame.  From Herbert Xu.

14) TCCR update race and other fixes to ravb driver from Sergei
    Shtylyov.

15) Fix SKB leaks in caif_queue_rcv_skb(), from Eric Dumazet.

16) Fix panics on packet scheduler filter replace, from Daniel Borkmann.

17) Make sure AF_PACKET sees properly IP headers in defragmented frames
    (via PACKET_FANOUT_FLAG_DEFRAG option), from Edward Hyunkoo Jee.

18) AF_NETLINK cannot hold mutex in RCU callback, fix from Florian
    Westphal.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (84 commits)
  ravb: fix ring memory allocation
  net: phy: dp83867: Fix warning check for setting the internal delay
  openvswitch: allocate nr_node_ids flow_stats instead of num_possible_nodes
  netlink: don't hold mutex in rcu callback when releasing mmapd ring
  ARM: net: fix vlan access instructions in ARM JIT.
  ARM: net: handle negative offsets in BPF JIT.
  ARM: net: fix condition for load_order > 0 when translating load instructions.
  tcp: suppress a division by zero warning
  drivers: net: cpsw: remove tx event processing in rx napi poll
  inet: frags: fix defragmented packet's IP header for af_packet
  net: mvneta: fix refilling for Rx DMA buffers
  stmmac: fix setting of driver data in stmmac_dvr_probe
  sched: cls_flow: fix panic on filter replace
  sched: cls_flower: fix panic on filter replace
  sched: cls_bpf: fix panic on filter replace
  net/mdio: fix mdio_bus_match for c45 PHY
  net: ratelimit warnings about dst entry refcount underflow or overflow
  caif: fix leaks and race in caif_queue_rcv_skb()
  qmi_wwan: add the second QMI/network interface for Sierra Wireless MC7305/MC7355
  ravb: fix race updating TCCR
  ...

Account for the configuration FIB_RULES=y && INET=n as FIB_RULES can
be selected by IPV6 or DECNET without INET.

Fixes: e7030878 ("fib: Add fib rule match on tunnel id")
Fixes: 3093fbe7 ("route: Per route IP tunnel metadata via lightweight tunnel")
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Per RFC 6724, section 4, "Candidate Source Addresses":

    It is RECOMMENDED that the candidate source addresses be the set
    of unicast addresses assigned to the interface that will be used
    to send to the destination (the "outgoing" interface).

Add a sysctl to enable this behaviour.
Signed-off-by: NErik Kline <ek@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support the new USB gigabit ethernet.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fix for:
net/mpls/mpls_iptunnel.c:73:19: sparse: incompatible types in comparison
expression (different address spaces)

remove incorrect rcu_dereference possibly left over from
earlier revisions of the code.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
bnx2x: update FW, rebrand and more

This patch series does several things - it updates the bnx2x FW into
7.12.30 which both contains some small fixes as well as opening the door
for several new features for the device - mainly vxlan/geneve offloads
and vlan filtering offload.
It then adds a new Multi-function mode [BD] which requires this FW in
order to operate.

In addition, this finally rebrands the driver from a 'broadcom' driver
into a 'qlogic' driver [although it would still reside under Broadcom's
tree in the kernel].
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Devices with up-to-date management FW will be able to store register dumps
on their persistent storage - in case management FW identifies a fatal
error it would gather and store such dumps, which could later be retrieved
using specific debug tools.

This patch adds the necessary part in the driver in order to make the
feature operational, as well as update users [under debug] during load
in case their device contains a dump of a previous crash.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support to a new multi-function mode, enabling driver to
initialize such devices and correctly interacting with management FW
for fully utilizing their features.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support to a new copper phy.
Signed-off-by: NYaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x still appears as a Broadcom driver even though the devices it
utilizes belong to Qlogic for more than a year.

This patch changes the various headers and the device strings to indicate
the correct ownership of the device.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This moves bnx2x into using 7.12.30 FW. Said firmware fixes the following:

 - Packets from a VF with pvid configured which were sent with a
   different vlan were transmitted instead of being discarded.

 - FCoE traffic might not recover after a failue while there's traffic
   to another function.

In addition, this FW opens the door for the driver to implement several
new features; Specifically, this enhances the device's support for
encapsulated packets and will allow vxlan/geneve offloads to be added in
the future, as well as vlan filtering offload.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull ARM64 fixes from Catalin Marinas:

 - arm64 build fix following the move of the thread_struct to the end of
   task_struct and the asm offsets becoming too large for the AArch64
   ISA

 - preparatory patch for moving irq_data struct members (applied now to
   reduce dependency for the next merging window)

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  ARM64/irq: Use access helper irq_data_get_affinity_mask()
  arm64: switch_to: calculate cpu context pointer using separate register

This is a preparatory patch for moving irq_data struct members.
Signed-off-by: NJiang Liu <jiang.liu@linux.intel.com>
Reviewed-by: NHanjun Guo <hanjun.guo@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Commit 0c8c0f03 ("x86/fpu, sched: Dynamically allocate 'struct fpu'")
moved the thread_struct to the bottom of task_struct. As a result, the
offset is now too large to be used in an immediate add on arm64 with
some kernel configs:

arch/arm64/kernel/entry.S: Assembler messages:
arch/arm64/kernel/entry.S:588: Error: immediate out of range
arch/arm64/kernel/entry.S:597: Error: immediate out of range

This patch calculates the offset using an additional register instead of
an immediate offset.

Fixes: 0c8c0f03 ("x86/fpu, sched: Dynamically allocate 'struct fpu'")
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Tested-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Track success and failure of TCP PMTU probing.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver is written as if it can adapt to a low memory situation  allocating
less RX  skbs and TX aligned buffers than the respective RX/TX ring sizes.  In
reality  though  the driver  would malfunction in this case. Stop being overly
smart and just fail in such situation -- this is achieved by moving the memory
allocation from ravb_ring_format() to ravb_ring_init().

We leave dma_map_single() calls in place but make their failure non-fatal
by marking the corresponding RX descriptors  with zero data size which should
prevent DMA to an invalid addresses.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add debugfs entry 'use_backdoor' to enable backdoor access to read sge
context. By default, we read sge context's via firmware. In case of FW
issues, one can enable backdoor access via debugfs to dump sge context
for debugging purpose.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix warning: logical ‘or’ of collectively exhaustive tests is always true

Change the internal delay check from an 'or' condition to an 'and'
condition.
Reported-by: NDavid Binderman <dcb314@hotmail.com>
Signed-off-by: NDan Murphy <dmurphy@ti.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If user did not specify an oif, try and get it from the via address.
If failed to get device, return with -ENODEV.
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some architectures like POWER can have a NUMA node_possible_map that
contains sparse entries. This causes memory corruption with openvswitch
since it allocates flow_cache with a multiple of num_possible_nodes() and
assumes the node variable returned by for_each_node will index into
flow->stats[node].

Use nr_node_ids to allocate a maximal sparse array instead of
num_possible_nodes().

The crash was noticed after 3af229f2 was applied as it changed the
node_possible_map to match node_online_map on boot.
Fixes: 3af229f2Signed-off-by: NChris J Arges <chris.j.arges@canonical.com>
Acked-by: NPravin B Shelar <pshelar@nicira.com>
Acked-by: NNishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Kirill A. Shutemov says:

This simple test-case trigers few locking asserts in kernel:

int main(int argc, char **argv)
{
        unsigned int block_size = 16 * 4096;
        struct nl_mmap_req req = {
                .nm_block_size          = block_size,
                .nm_block_nr            = 64,
                .nm_frame_size          = 16384,
                .nm_frame_nr            = 64 * block_size / 16384,
        };
        unsigned int ring_size;
	int fd;

	fd = socket(AF_NETLINK, SOCK_RAW, NETLINK_GENERIC);
        if (setsockopt(fd, SOL_NETLINK, NETLINK_RX_RING, &req, sizeof(req)) < 0)
                exit(1);
        if (setsockopt(fd, SOL_NETLINK, NETLINK_TX_RING, &req, sizeof(req)) < 0)
                exit(1);

	ring_size = req.nm_block_nr * req.nm_block_size;
	mmap(NULL, 2 * ring_size, PROT_READ|PROT_WRITE, MAP_SHARED, fd, 0);
	return 0;
}

+++ exited with 0 +++
BUG: sleeping function called from invalid context at /home/kas/git/public/linux-mm/kernel/locking/mutex.c:616
in_atomic(): 1, irqs_disabled(): 0, pid: 1, name: init
3 locks held by init/1:
 #0:  (reboot_mutex){+.+...}, at: [<ffffffff81080959>] SyS_reboot+0xa9/0x220
 #1:  ((reboot_notifier_list).rwsem){.+.+..}, at: [<ffffffff8107f379>] __blocking_notifier_call_chain+0x39/0x70
 #2:  (rcu_callback){......}, at: [<ffffffff810d32e0>] rcu_do_batch.isra.49+0x160/0x10c0
Preemption disabled at:[<ffffffff8145365f>] __delay+0xf/0x20

CPU: 1 PID: 1 Comm: init Not tainted 4.1.0-00009-gbddf4c4818e0 #253
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS Debian-1.8.2-1 04/01/2014
 ffff88017b3d8000 ffff88027bc03c38 ffffffff81929ceb 0000000000000102
 0000000000000000 ffff88027bc03c68 ffffffff81085a9d 0000000000000002
 ffffffff81ca2a20 0000000000000268 0000000000000000 ffff88027bc03c98
Call Trace:
 <IRQ>  [<ffffffff81929ceb>] dump_stack+0x4f/0x7b
 [<ffffffff81085a9d>] ___might_sleep+0x16d/0x270
 [<ffffffff81085bed>] __might_sleep+0x4d/0x90
 [<ffffffff8192e96f>] mutex_lock_nested+0x2f/0x430
 [<ffffffff81932fed>] ? _raw_spin_unlock_irqrestore+0x5d/0x80
 [<ffffffff81464143>] ? __this_cpu_preempt_check+0x13/0x20
 [<ffffffff8182fc3d>] netlink_set_ring+0x1ed/0x350
 [<ffffffff8182e000>] ? netlink_undo_bind+0x70/0x70
 [<ffffffff8182fe20>] netlink_sock_destruct+0x80/0x150
 [<ffffffff817e484d>] __sk_free+0x1d/0x160
 [<ffffffff817e49a9>] sk_free+0x19/0x20
[..]

Cong Wang says:

We can't hold mutex lock in a rcu callback, [..]

Thomas Graf says:

The socket should be dead at this point. It might be simpler to
add a netlink_release_ring() function which doesn't require
locking at all.
Reported-by: N"Kirill A. Shutemov" <kirill@shutemov.name>
Diagnosed-by: NCong Wang <cwang@twopensource.com>
Suggested-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Edward Cree says:

====================
sfc: support for cascaded multicast filtering

Recent versions of firmware for SFC9100 adapters add support for filter
 chaining, in which packets matching multiple filters are delivered to all
 filters' recipients, rather than only the highest match-priority filter as was
 previously the case.
This patch series enables this feature and redesigns the filter handling code
 to make use of it; in particular, subscribing to a multicast address on one
 function no longer prevents traffic to that address reaching another function
 which is in promiscuous or allmulti mode.
If the firmware does not support filter chaining, the driver will fall back to
 the old behaviour.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Separate functions for inserting individual and promisc filters; explicit
 fallback logic in efx_ef10_filter_sync_rx_mode(), in order not to overload
 the 'promisc' flag as also meaning "fall back to promisc".
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the workaround to support cascaded multicast filters ("workaround_26807") is
enabled, the broadcast filter and individual multicast filters are not inserted
when in promiscuous or allmulti mode.

There is a race while inserting and removing filters when entering and leaving
promiscuous mode.  When changing promiscuous state with cascaded multicast
filters, the old multicast filters are removed before inserting the new filters
to avoid duplicating packets; this can lead to dropped packets until all
filters have been inserted.

The efx_nic:mc_promisc flag is added to record the presence of a multicast
promiscuous filter; this gives a simple way to tell if the promiscuous state is
changing.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change is only re-factoring; there are no changes to functionality
 except for a slight elaboration of an error message (on mismatch filter
 insertion failure).
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a function is in promiscuous mode and another function has a broadcast or
 multicast filter inserted, the function in promiscuous mode won't see that
 broadcast or multicast traffic.
Most notably this breaks broadcast, which means ARP doesn't work. Less
 show-stoppingly, a function listening on a multicast address that's also in
 promiscuous mode will not see that multicast traffic if another function is
 also listening on that multicast address.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>