Pull i915 drm fixes from Dave Airlie:
 "These should be the last two fixes for i915, one is for a fence leak
  killing X on some older GPUs, and one is a late regression partial
  revert for an swiotlb/xen/i915 interaction, Konrad has promised to
  figure out the proper answer, and this patch is the best thing to do
  at this stage to avoid regressing"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: make compact dma scatter lists creation work with SWIOTLB backend.
  drm/i915: Restore fences after resume and GPU resets

Pull regulator fix from Mark Brown:
 "Fix module loading for tps6586x.

  A simple one liner fix to make module loading work for distros
  (product specific kernels tend to have things built in)"

* tag 'regulator-v3.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  mfd: tps6586x: correct device name of the regulator cell

Pull GPIO regression fix from Grant Likely:
 "It took a while to work out the correct solution to this regression.
  It is sorted now.  This branch was constructed and tested by Tony.
  I've verified that it builds and signed the tag"

* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
  gpio/omap: don't use linear domain mapping for OMAP1

Pull late power management and ACPI fixes from Rafael Wysocki:
 "Sorry about the timing of this, but ACPI-based docking stations with
  PCI devices on them and ATA bays would be hardly usable with 3.10
  without it.  We've been working on these fixes for the last couple of
  weeks and everyone involved appears to be reasonably comfortable with
  them now.

  The PM part is one fix for a cpufreq regression introduced recently

   - Fix for an ACPI dock regression introduced by the recent rework of
     the ACPI-based PCI hotplug code (acpiphp) that caused it to be
     initialized before the ACPI dock driver, which is incorrect (ACPI
     dock has to be initialized before acpiphp so that acpiphp can
     register PCI devices on docking stations with it for PCI hotplug on
     re-dock to work).  From Jiang Liu.

   - Fix for PCI resources allocation in the ACPI-based PCI hotplug code
     (acpiphp) that makes it use the same PCI resources assignment rules
     during runtime hotplug that are used during boot (the BIOS' choices
     are now respected in both cases).  This prevents PCI resource
     allocation failures during hotplug from happening in some cases.
     From Jiang Liu.

   - Fix for ordering and synchronization issues during hot-removal of
     PCI devices on docking stations.  It makes the ACPI dock code carry
     out the PCI devices removal synchronously during undock instead of
     spawning a separate asynchronous work item to remove each of them
     without even bothering to wait for all those work items to
     complete.  The hot-addition part is changed analogously.

   - Fix for a regression (introduced a few releases ago) that removed
     the code to register a hotplug notificaion handler for for ATA
     ports/devices inadvertently which prevented ATA bays hotplug from
     working.  The missing code is added back with some improvements.
     From Aaron Lu.

   - Fix for a recent cpufreq regression causing a NULL pointer
     dereference to trigger in od_set_powersave_bias() in some
     situations from Jacob Shin"

* tag 'pm+acpi-3.10-late' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: fix NULL pointer deference at od_set_powersave_bias()
  libata-acpi: add back ACPI based hotplug functionality
  ACPI / dock / PCI: Synchronous handling of dock events for PCI devices
  PCI / ACPI: Use boot-time resource allocation rules during hotplug
  ACPI / dock: Initialize ACPI dock subsystem upfront

Pull perf fixes from Ingo Molnar:
 "Three small fixlets"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  hw_breakpoint: Use cpu_possible_mask in {reserve,release}_bp_slot()
  hw_breakpoint: Fix cpu check in task_bp_pinned(cpu)
  kprobes: Fix arch_prepare_kprobe to handle copy insn failures

Pull ARM fixes from Russell King:
 "Another round of ARM fixes.  Largest one is the second half of the
  PJ4B fix which was pushed in the previous -rc - this one was delayed
  because its original caused a build regression while trying to fix a
  regression!

  As ever, noMMU gets forgotten when fixing problems on MMU, so we have
  a noMMU fix for a previous fix included in this set.

  A couple of fixes from Lorenzo for problems with the ARM DT CPU code,
  and a one liner to remove the buggy 'wait for interrupt' with FA526
  cores"

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7773/1: PJ4B: Add support for errata 4742
  ARM: 7772/1: Fix missing flush_kernel_dcache_page() for noMMU
  ARM: 7763/1: kernel: fix __cpu_logical_map default initialization
  ARM: 7762/1: kernel: fix arm_dt_init_cpu_maps() to skip non-cpu nodes
  ARM: 7760/1: cpu_fa526_do_idle: remove WFI

Pull FCoE fix from Robert W Love:
 "This patch fixes a critical bug that was introduced in 3.9 related to
  VLAN tagging FCoE frames"

* tag 'critical_fix_for_3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/rwlove/fcoe:
  fcoe: Use correct API to set vlan tag for FCoE Ethertype skbs

Pull Ceph fix from Sage Weil:
 "This fixes another problem with using v2 images on 3.10 due to the
  order in which fields are read from the image header.

  Hopefully this is the last one"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: fetch object order before using it

Commit ede4d7a5 ("gpio/omap: convert gpio irq domain to linear mapping")
converted the OMAP GPIO driver to use a linear mapping for the GPIO IRQ
domain instead of using a legacy mapping. Not using a legacy mapping has
a number of benefits but it requires the platform to support SPARSE_IRQ
which currently is not supported on OMAP1.

So this change caused a regression on OMAP1 platforms [1].

Since this issue is not present on all OMAP2+ platforms, there is no need to
revert the driver to use legacy domain mapping for all the platforms.

[1]: http://www.mail-archive.com/linux-omap@vger.kernel.org/msg89005.htmlSigned-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

* pm-fixes:
  cpufreq: fix NULL pointer deference at od_set_powersave_bias()

* acpi-fixes:
  libata-acpi: add back ACPI based hotplug functionality
  ACPI / dock / PCI: Synchronous handling of dock events for PCI devices
  PCI / ACPI: Use boot-time resource allocation rules during hotplug
  ACPI / dock: Initialize ACPI dock subsystem upfront

When initializing the default powersave_bias value, we need to first
make sure that this policy is running the ondemand governor.
Reported-and-tested-by: NTim Gardner <tim.gardner@canonical.com>
Signed-off-by: NJacob Shin <jacob.shin@amd.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

rbd_dev_v2_header_onetime() fetches striping information, and
checks whether the image can be read by compariing the stripe unit
to the object size. It determines the object size by shifting
the object order, which is 0 at this point since it has not been
read yet. Move the call to get the image size and object order
before rbd_dev_v2_header_onetime() so it is set before use.
Signed-off-by: NJosh Durgin <josh.durgin@inktank.com>
Reviewed-by: NSage Weil <sage@inktank.com>

fcoe_xmit was coded such that it would skip the vlan net device/layer
and instead set some vlan flags and transmit on the real net device.
The real net device has code that would add the vlan tag for fcoe skbs.
This avoids some extra processing for data frames and provides a small
performance improvement.

Since fcoe_xmit was not using the vlan net device, __vlan_put_tag
within the real net device's xmit routine was ultimately being
called to set the vlan tag.

With the below change the behavior of __vlan_put_tag changed slightly,
it now sets the skb->protocol = vlan_proto. vlan_proto was not a field
being set by fcoe_xmit, so the skb->protocol is now not being set to
ETH_P_8021Q, as it should be.

This patch converts fcoe_xmit to use the vlan_put_tag routine which
will tag the skb and fcoe will continue to transmit fcoe skbs on the
real net device.

For reference, the below change was the one that altered the
__vlan_put_tag behavior.

  commit 86a9bad3
  Author: Patrick McHardy <kaber@trash.net>
  Date:   Fri Apr 19 02:04:30 2013 +0000

      net: vlan: add protocol argument to packet tagging functions

      Add a protocol argument to the VLAN packet tagging functions. In case of HW
      tagging, we need that protocol available in the ndo_start_xmit functions,
      so it is stored in a new field in the skb. The new field fits into a hole
      (on 64 bit) and doesn't increase the sks's size.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>

Pull s390 fixes from Martin Schwidefsky:
 "A couple of last-minute fixes: a build regression for !SMP, a recent
  memory detection patch caused kdump to break, a regression in regard
  to sscanf vs reboot from FCP, and two fixes in the DMA mapping code
  for PCI"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/ipl: Fix FCP WWPN and LUN format strings for read
  s390/mem_detect: fix memory hole handling
  s390/dma: support debug_dma_mapping_error
  s390/dma: fix mapping_error detection
  s390/irq: Only define synchronize_irq() on SMP

Pull powerpc bugfix from Ben Herrenschmidt:
 "This is a fix for a regression causing a freescale "83xx" based
  platforms to crash on boot due to some PCI breakage"

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/pci: Fix boot panic on mpc83xx (regression)

Pull fuse bugfix from Miklos Szeredi:
 "This fixes a race between fallocate() and truncate()"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: hold i_mutex in fuse_file_fallocate()

Pull spi updates from Mark Brown:
 "A few last minute SPI updates: fix a missized allocation and use
  atomic allocations in atomic context in the PXA driver, and fix the
  checking of return codes in the S3C64xx driver which caused spurious
  errors under heavy load."

* tag 'spi-v3.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi/pxa2xx: fix memory corruption due to wrong size used in devm_kzalloc()
  spi/pxa2xx: use GFP_ATOMIC in sg table allocation
  spi: s3c64xx: Fix pm_runtime_get_sync() return value check

Git commit 90797e6d
("drm/i915: create compact dma scatter lists for gem objects") makes
certain assumptions about the under laying DMA API that are not always
correct.

On a ThinkPad X230 with an Intel HD 4000 with Xen during the bootup
I see:

[drm:intel_pipe_set_base] *ERROR* pin & fence failed
[drm:intel_crtc_set_config] *ERROR* failed to set mode on [CRTC:3], err = -28

Bit of debugging traced it down to dma_map_sg failing (in
i915_gem_gtt_prepare_object) as some of the SG entries were huge (3MB).

That unfortunately are sizes that the SWIOTLB is incapable of handling -
the maximum it can handle is a an entry of 512KB of virtual contiguous
memory for its bounce buffer. (See IO_TLB_SEGSIZE).

Previous to the above mention git commit the SG entries were of 4KB, and
the code introduced by above git commit squashed the CPU contiguous PFNs
in one big virtual address provided to DMA API.

This patch is a simple semi-revert - were we emulate the old behavior
if we detect that SWIOTLB is online. If it is not online then we continue
on with the new compact scatter gather mechanism.

An alternative solution would be for the the '.get_pages' and the
i915_gem_gtt_prepare_object to retry with smaller max gap of the
amount of PFNs that can be combined together - but with this issue
discovered during rc7 that might be too risky.
Reported-and-Tested-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Imre Deak <imre.deak@intel.com>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
CC: David Airlie <airlied@linux.ie>
CC: <dri-devel@lists.freedesktop.org>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Merge tag 'drm-intel-fixes-2013-06-24' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes

One remaining regression fix for i915. I've left it in -fixes for more
than a week since it's in tricky code, and it took us a few kernel
releases to notice the regression at all. The fence leak is especially
annoying on gen2/3 and will kill userspace there quickly. For extra
paranoia we've added a WARN in -next to catch this, things seem to be
solid now.

* tag 'drm-intel-fixes-2013-06-24' of git://people.freedesktop.org/~danvet/drm-intel:
  drm/i915: Restore fences after resume and GPU resets

Commit 30dcf76a "libata: migrate ACPI code over to new bindings"
mistakenly dropped the code to register hotplug notificaion handler
for ATA port/devices, causing regression for people using ATA bay,
as kernel bug #59871 shows.

Fix this by adding back the hotplug notification handler registration
code.  Since this code has to be run once and notification needs to
be installed on every ATA port/devices handle no matter if there is
actual device attached, we can't do this in binding time for ATA
device ACPI handle, as the binding only occurs when a SCSI device is
created, i.e. there is device attached.  So introduce the
ata_acpi_hotplug_init() function to loop scan all ATA ACPI handles
and if it is available, install the notificaion handler for it during
ATA init time.

With the ATA ACPI handle binding to SCSI device tree, it is possible
now that when the SCSI hotplug work removes the SCSI device, the ACPI
unbind function will find that the corresponding ACPI device has
already been deleted by dock driver, causing a scaring message like:
[  128.263966] scsi 4:0:0:0: Oops, 'acpi_handle' corrupt
Fix this by waiting for SCSI hotplug task finish in our notificaion
handler, so that the removal of ACPI device done in ACPI unbind
function triggered by the removal of SCSI device is run earlier when
ACPI device is still available.

[rjw: Rebased]
References: https://bugzilla.kernel.org/show_bug.cgi?id=59871Reported-bisected-and-tested-by: NDirk Griesbach <spamthis@freenet.de>
Signed-off-by: NAaron Lu <aaron.lu@intel.com>
Acked-by: NTejun Heo <tj@kernel.org>
Cc: 3.6+ <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The following commit caused a fatal oops when booting on mpc83xx with
a non-express PCI bus (regardless of whether a PCI device is present):

commit 50d8f87d
Author: Rojhalat Ibrahim <imr@rtschenk.de>
Date:   Mon Apr 8 10:15:28 2013 +0200

    powerpc/fsl-pci Make PCIe hotplug work with Freescale PCIe controllers

    Up to now the PCIe link status on Freescale PCIe controllers was only
    checked once at boot time. So hotplug did not work. With this patch the
    link status is checked on every config read. PCIe devices not present at
    boot time are found after doing 'echo 1 >/sys/bus/pci/rescan'.
Signed-off-by: NRojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch fixes the issue by calling setup_indirect_pci for all device types.
fsl_indirect_read_config is now only used for booke/86xx PCIe controllers.
Reported-by: NMichael Guntsche <mike@it-loops.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: NRojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: NScott Wood <scottwood@freescale.com>

This commit fixes the regression on Armada 370 (the kernal hang during
boot) introduced by the commit: "ARM: 7691/1: mm: kill unused
TLB_CAN_READ_FROM_L1_CACHE and use ALT_SMP instead".

When coming out of either a Wait for Interrupt (WFI) or a Wait for
Event (WFE) IDLE states, a specific timing sensitivity exists between
the retiring WFI/WFE instructions and the newly issued subsequent
instructions. This sensitivity can result in a CPU hang scenario.  The
workaround is to insert either a Data Synchronization Barrier (DSB) or
Data Memory Barrier (DMB) command immediately after the WFI/WFE
instruction.

This commit was based on the work of Lior Amsalem, but heavily
modified to apply the errata fix dynamically according to the
processor type thanks to the suggestions of Russell King and Nicolas
Pitre.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: NWill Deacon <will.deacon@arm.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Tested-by: NWilly Tarreau <w@1wt.eu>
Cc: <stable@vger.kernel.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Commit 1bc39742 (ARM: 7755/1: handle user space mapped pages in
flush_kernel_dcache_page) moved the implementation of
flush_kernel_dcache_page() into mm/flush.c but did not implement it
on noMMU ARM.
Signed-off-by: NSimon Baatz <gmbnomis@gmail.com>
Acked-by: NKevin Hilman <khilman@linaro.org>
Cc: <stable@vger.kernel.org> # 3.2+: 1bc39742: ARM: 7755/1
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The __cpu_logical_map array is statically initialized to 0, which is a valid
MPIDR value. To prevent issues with the current implementation, this patch
defines an MPIDR_INVALID value, and statically initializes the
__cpu_logical_map[] array to it. Entries in the arm_dt_init_cpu_maps()
tmp_map array used to stash DT reg properties while parsing DT are initialized
with the MPIDR_INVALID value as well for consistency.
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The introduction of the cpu-map topology node in the cpus node implies
that cpus node might have children that are not cpu nodes. The DT
parsing code needs updating otherwise it would check for cpu nodes
properties in nodes that are not required to contain them, resulting
in warnings that have no bearing on bindings defined in the dts source file.

Cc: <stable@vger.kernel.org> [3.8+]
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As it was already suggested by Russell King and Arnd Bergmann:

https://lkml.org/lkml/2013/5/16/133

moxart and gemini seem to be the only platforms using CPU_FA526,
and instead of pointing arm_pm_idle to an empty function from
platform code, it makes sense to remove WFI code from the processor
specific idle function.

Applies to arm-soc/for-next (and 3.10-rc1).

Changes since v1:

1. remove WFI but make sure cpu_fa526_do_idle do not fall through
   to cpu_fa526_dcache_clean_area

Note: moxart boots and prints to UART without this patch, but input is broken.
Signed-off-by: NJonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Change the device name of the regulator function to the one chosen for
MODULE_ALIAS. This fixes kernel auto-module loading for the regulator function.
Signed-off-by: NMarc Dietrich <marvin24@gmx.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

The interactions between the ACPI dock driver and the ACPI-based PCI
hotplug (acpiphp) are currently problematic because of ordering
issues during hot-remove operations.

First of all, the current ACPI glue code expects that physical
devices will always be deleted before deleting the companion ACPI
device objects.  Otherwise, acpi_unbind_one() will fail with a
warning message printed to the kernel log, for example:

[  185.026073] usb usb5: Oops, 'acpi_handle' corrupt
[  185.035150] pci 0000:1b:00.0: Oops, 'acpi_handle' corrupt
[  185.035515] pci 0000:18:02.0: Oops, 'acpi_handle' corrupt
[  180.013656]  port1: Oops, 'acpi_handle' corrupt

This means, in particular, that struct pci_dev objects have to
be deleted before the struct acpi_device objects they are "glued"
with.

Now, the following happens the during the undocking of an ACPI-based
dock station:
 1) hotplug_dock_devices() invokes registered hotplug callbacks to
    destroy physical devices associated with the ACPI device objects
    depending on the dock station.  It calls dd->ops->handler() for
    each of those device objects.
 2) For PCI devices dd->ops->handler() points to
    handle_hotplug_event_func() that queues up a separate work item
    to execute _handle_hotplug_event_func() for the given device and
    returns immediately.  That work item will be executed later.
 3) hotplug_dock_devices() calls dock_remove_acpi_device() for each
    device depending on the dock station.  This runs acpi_bus_trim()
    for each of them, which causes the underlying ACPI device object
    to be destroyed, but the work items queued up by
    handle_hotplug_event_func() haven't been started yet.
 4) _handle_hotplug_event_func() queued up in step 2) are executed
    and cause the above failure to happen, because the PCI devices
    they handle do not have the companion ACPI device objects any
    more (those objects have been deleted in step 3).

The possible breakage doesn't end here, though, because
hotplug_dock_devices() may return before at least some of the
_handle_hotplug_event_func() work items spawned by it have a
chance to complete and then undock() will cause _DCK to be
evaluated and that will cause the devices handled by the
_handle_hotplug_event_func() to go away possibly while they are
being accessed.

This means that dd->ops->handler() for PCI devices should not point
to handle_hotplug_event_func().  Instead, it should point to a
function that will do the work of _handle_hotplug_event_func()
synchronously.  For this reason, introduce such a function,
hotplug_event_func(), and modity acpiphp_dock_ops to point to
it as the handler.

Unfortunately, however, this is not sufficient, because if the dock
code were not changed further, hotplug_event_func() would now
deadlock with hotplug_dock_devices() that called it, since it would
run unregister_hotplug_dock_device() which in turn would attempt to
acquire the dock station's hp_lock mutex already acquired by
hotplug_dock_devices().

To resolve that deadlock use the observation that
unregister_hotplug_dock_device() won't need to acquire hp_lock
if PCI bridges the devices on the dock station depend on are
prevented from being removed prematurely while the first loop in
hotplug_dock_devices() is in progress.

To make that possible, introduce a mechanism by which the callers of
register_hotplug_dock_device() can provide "init" and "release"
routines that will be executed, respectively, during the addition
and removal of the physical device object associated with the
given ACPI device handle.  Make acpiphp use two new functions,
acpiphp_dock_init() and acpiphp_dock_release(), that call
get_bridge() and put_bridge(), respectively, on the acpiphp bridge
holding the given device, for this purpose.

In addition to that, remove the dock station's list of
"hotplug devices" and make the dock code always walk the whole list
of "dependent devices" instead in such a way that the loops in
hotplug_dock_devices() and dock_event() (replacing the loops over
"hotplug devices") will take references to the list entries that
register_hotplug_dock_device() has been called for.  That prevents
the "release" routines associated with those entries from being
called while the given entry is being processed and for PCI
devices this means that their bridges won't be removed (by a
concurrent thread) while hotplug_event_func() handling them is
being executed.

This change is based on two earlier patches from Jiang Liu.

References: https://bugzilla.kernel.org/show_bug.cgi?id=59501Reported-and-tested-by: NAlexander E. Patrakov <patrakov@gmail.com>
Tracked-down-by: NJiang Liu <jiang.liu@huawei.com>
Tested-by: NIllya Klymov <xanf@xanf.me>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NYinghai Lu <yinghai@kernel.org>
Cc: 3.9+ <stable@vger.kernel.org>

The following git commit changed the behavior of sscanf:

commit 53809751
Author: Jan Beulich <JBeulich@suse.com>
Date:   Mon Dec 17 16:01:31 2012 -0800
    sscanf: don't ignore field widths for numeric conversions

This broke the WWPN and LUN sysfs attributes for s390 reipl and dump
on panic.

Example:

$ echo 0x0123456701234567 > /sys/firmware/reipl/fcp/wwpn
$ cat /sys/firmware/reipl/fcp/wwpn
0x0001234567012345

So fix this and use format strings that work also with the
new sscanf implementation:

$ echo 0x012345670123456789 > /sys/firmware/reipl/fcp/wwpn
$ cat /sys/firmware/reipl/fcp/wwpn
0x0123456701234567

Cc: stable@vger.kernel.org # 3.8+
Reviewed-by: NSteffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: NMichael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Fix new kernel-doc warning in fs/splice.c:

  Warning(fs/splice.c:1298): No description found for parameter 'opos'
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull input subsystem updates from Dmitry Torokhov:
 "A few small fixups for cyttsp, wacom and xpad drivers"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: xpad - fix for "Mad Catz Street Fighter IV FightPad" controllers
  Input: wacom - add a new stylus (0x100802) for Intuos5 and Cintiqs
  Input: add missing dependencies on CONFIG_HAS_IOMEM
  Input: cyttsp - fix swapped mfg_stat and mfg_cmd registers
  Input: cyttsp - add missing handshake
  Input: cyttsp - fix memcpy size param

On x86 platforms, the kernel respects PCI resource assignments from
the BIOS and only reassigns resources for unassigned BARs at boot
time.  However, with the ACPI-based hotplug (acpiphp), it ignores the
BIOS' PCI resource assignments completely and reassigns all resources
by itself.  This causes differences in PCI resource allocation
between boot time and runtime hotplug to occur, which is generally
undesirable and sometimes actively breaks things.

Namely, if there are enough resources, reassigning all PCI resources
during runtime hotplug should work, but it may fail if the resources
are constrained.  This may happen, for instance, when some PCI
devices with huge MMIO BARs are involved in the runtime hotplug
operations, because the current PCI MMIO alignment algorithm may
waste huge chunks of MMIO address space in those cases.

On the Alexander's Sony VAIO VPCZ23A4R the BIOS allocates limited
MMIO resources for the dock station which contains a device
(graphics adapter) with a 256MB MMIO BAR.  An attempt to reassign
that during runtime hotplug causes the dock station MMIO window to be
exhausted and acpiphp fails to allocate resources for the majority
of devices on the dock station as a result.

To prevent that from happening, modify acpiphp to follow the boot
time resources allocation behavior so that the BIOS' resource
assignments are respected during runtime hotplug too.

[rjw: Changelog]
References: https://bugzilla.kernel.org/show_bug.cgi?id=56531Reported-and-tested-by: NAlexander E. Patrakov <patrakov@gmail.com>
Tested-by: NIllya Klymov <xanf@xanf.me>
Signed-off-by: NJiang Liu <jiang.liu@huawei.com>
Acked-by: NYinghai Lu <yinghai@kernel.org>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Commit 3b63aaa7 (PCI: acpiphp: Do not use ACPI PCI subdriver
mechanism) introduced an ACPI dock support regression, because it
changed the relative initialization order of the ACPI dock subsystem
and the ACPI-based PCI hotplug (acpiphp).

Namely, the ACPI dock subsystem has to be initialized before
acpiphp_enumerate_slots() is first run, which after commit
3b63aaa7 happens during the initial enumeration of the PCI
hierarchy triggered by the initial ACPI namespace scan in
acpi_scan_init().  For this reason, the dock subsystem has to be
initialized before the initial ACPI namespace scan in
acpi_scan_init().

To make that happen, modify the ACPI dock subsystem to be
non-modular and add the invocation of its initialization routine,
acpi_dock_init(), to acpi_scan_init() directly before the initial
namespace scan.

[rjw: Changelog, removal of dock_exit().]
References: https://bugzilla.kernel.org/show_bug.cgi?id=59501Reported-and-tested-by: NAlexander E. Patrakov <patrakov@gmail.com>
Tested-by: NIllya Klymov <xanf@xanf.me>
Signed-off-by: NJiang Liu <jiang.liu@huawei.com>
Acked-by: NYinghai Lu <yinghai@kernel.org>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull ARM SoC fixes from Arnd Bergmann:
 "These are two fixes that came in this week, one for a regression we
  introduced in 3.10 in the GIC interrupt code, and the other one fixes
  a typo in newly introduced code"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  irqchip: gic: call gic_cpu_init() as well in CPU_STARTING_FROZEN case
  ARM: dts: Correct the base address of pinctrl_3 on Exynos5250

Merge tag 'driver-core-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fix from Greg Kroah-Hartman:
 "Here's a single patch for the firmware core that resolves a reported
  oops in the firmware core that people have been hitting."

* tag 'driver-core-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  firmware loader: fix use-after-free by double abort

Pull USB fixes from Greg Kroah-Hartman:
 "Here are two USB patches for 3.10.

  One updates the Kconfig wording for CONFIG_USB_PHY to make it,
  hopefully, more obvious what this option is (I know you complained
  about this when it hit the tree.) The other is a new device id for a
  driver"

* tag 'usb-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: serial: ti_usb_3410_5052: new device id for Abbot strip port cable
  usb: phy: Improve Kconfig help for CONFIG_USB_PHY