From e9dbadf7881375ebb234ff579838f85df2abe4cf Mon Sep 17 00:00:00 2001 From: Ondrej Zary Date: Mon, 3 Jul 2017 03:59:05 -0400 Subject: [PATCH] scsi: g_NCR5380: End PDMA transfer correctly on target disconnection When an IRQ arrives during PDMA transfer, pread() and pwrite() return without waiting for the 53C80 registers to be ready and this ends up messing up the chip state. This was observed with SONY CDU-55S which is slow enough to disconnect during 4096-byte reads. IRQ during PDMA is not an error so don't return -1. Instead, store the remaining byte count for use by NCR5380_dma_residual(). [Poll for the BASR_END_DMA_TRANSFER condition rather than remove the error message -- F.T.] Signed-off-by: Ondrej Zary Signed-off-by: Finn Thain Tested-by: Ondrej Zary Signed-off-by: Martin K. Petersen --- drivers/scsi/g_NCR5380.c | 48 ++++++++++++++++++++++++++-------------- 1 file changed, 31 insertions(+), 17 deletions(-) diff --git a/drivers/scsi/g_NCR5380.c b/drivers/scsi/g_NCR5380.c index fbb28ed0fce8..f209b12280cc 100644 --- a/drivers/scsi/g_NCR5380.c +++ b/drivers/scsi/g_NCR5380.c @@ -44,12 +44,13 @@ int c400_ctl_status; \ int c400_blk_cnt; \ int c400_host_buf; \ - int io_width + int io_width; \ + int pdma_residual #define NCR5380_dma_xfer_len generic_NCR5380_dma_xfer_len #define NCR5380_dma_recv_setup generic_NCR5380_pread #define NCR5380_dma_send_setup generic_NCR5380_pwrite -#define NCR5380_dma_residual NCR5380_dma_residual_none +#define NCR5380_dma_residual generic_NCR5380_dma_residual #define NCR5380_intr generic_NCR5380_intr #define NCR5380_queue_command generic_NCR5380_queue_command @@ -500,10 +501,8 @@ static inline int generic_NCR5380_pread(struct NCR5380_hostdata *hostdata, while (1) { if (NCR5380_read(hostdata->c400_blk_cnt) == 0) break; - if (NCR5380_read(hostdata->c400_ctl_status) & CSR_GATED_53C80_IRQ) { - printk(KERN_ERR "53C400r: Got 53C80_IRQ start=%d, blocks=%d\n", start, blocks); - return -1; - } + if (NCR5380_read(hostdata->c400_ctl_status) & CSR_GATED_53C80_IRQ) + goto out_wait; while (NCR5380_read(hostdata->c400_ctl_status) & CSR_HOST_BUF_NOT_RDY) ; /* FIXME - no timeout */ @@ -542,13 +541,19 @@ static inline int generic_NCR5380_pread(struct NCR5380_hostdata *hostdata, if (!(NCR5380_read(hostdata->c400_ctl_status) & CSR_GATED_53C80_IRQ)) printk("53C400r: no 53C80 gated irq after transfer"); +out_wait: + hostdata->pdma_residual = len - start; + /* wait for 53C80 registers to be available */ while (!(NCR5380_read(hostdata->c400_ctl_status) & CSR_53C80_REG)) ; - if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER)) - printk(KERN_ERR "53C400r: no end dma signal\n"); - + if (NCR5380_poll_politely(hostdata, BUS_AND_STATUS_REG, + BASR_END_DMA_TRANSFER, BASR_END_DMA_TRANSFER, + HZ / 64) < 0) + scmd_printk(KERN_ERR, hostdata->connected, "%s: End of DMA timeout (%d)\n", + __func__, hostdata->pdma_residual); + return 0; } @@ -571,10 +576,8 @@ static inline int generic_NCR5380_pwrite(struct NCR5380_hostdata *hostdata, NCR5380_write(hostdata->c400_ctl_status, CSR_BASE); NCR5380_write(hostdata->c400_blk_cnt, blocks); while (1) { - if (NCR5380_read(hostdata->c400_ctl_status) & CSR_GATED_53C80_IRQ) { - printk(KERN_ERR "53C400w: Got 53C80_IRQ start=%d, blocks=%d\n", start, blocks); - return -1; - } + if (NCR5380_read(hostdata->c400_ctl_status) & CSR_GATED_53C80_IRQ) + goto out_wait; if (NCR5380_read(hostdata->c400_blk_cnt) == 0) break; @@ -612,18 +615,24 @@ static inline int generic_NCR5380_pwrite(struct NCR5380_hostdata *hostdata, blocks--; } +out_wait: + hostdata->pdma_residual = len - start; + /* wait for 53C80 registers to be available */ while (!(NCR5380_read(hostdata->c400_ctl_status) & CSR_53C80_REG)) { udelay(4); /* DTC436 chip hangs without this */ /* FIXME - no timeout */ } - if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER)) { - printk(KERN_ERR "53C400w: no end dma signal\n"); - } - while (!(NCR5380_read(TARGET_COMMAND_REG) & TCR_LAST_BYTE_SENT)) ; // TIMEOUT + + if (NCR5380_poll_politely(hostdata, BUS_AND_STATUS_REG, + BASR_END_DMA_TRANSFER, BASR_END_DMA_TRANSFER, + HZ / 64) < 0) + scmd_printk(KERN_ERR, hostdata->connected, "%s: End of DMA timeout (%d)\n", + __func__, hostdata->pdma_residual); + return 0; } @@ -642,6 +651,11 @@ static int generic_NCR5380_dma_xfer_len(struct NCR5380_hostdata *hostdata, return min(transfersize, DMA_MAX_SIZE); } +static int generic_NCR5380_dma_residual(struct NCR5380_hostdata *hostdata) +{ + return hostdata->pdma_residual; +} + /* * Include the NCR5380 core code that we build our driver around */ -- GitLab