提交 e19499ae 编写于 作者: T Thomas Abraham 提交者: Chris Ball

mmc: sdhci-s3c: let device core setup the default pin configuration

With device core now able to setup the default pin configuration,
the call to devm_pinctrl_get_select_default can be removed. And
the pin configuration code based on the deprecated Samsung specific
gpio bindings is also removed.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>
上级 4a2d8ecc
......@@ -5,13 +5,6 @@ MMC, SD and eMMC storage mediums. This file documents differences between the
core mmc properties described by mmc.txt and the properties used by the
Samsung implmentation of the SDHCI controller.
Note: The mmc core bindings documentation states that if none of the core
card-detect bindings are used, then the standard sdhci card detect mechanism
is used. The Samsung's SDHCI controller bindings extends this as listed below.
[A] The property "samsung,cd-pinmux-gpio" can be used as stated in the
"Optional Board Specific Properties" section below.
Required SoC Specific Properties:
- compatible: should be one of the following
- "samsung,s3c6410-sdhci": For controllers compatible with s3c6410 sdhci
......@@ -20,18 +13,8 @@ Required SoC Specific Properties:
controller.
Required Board Specific Properties:
- Samsung GPIO variant (will be completely replaced by pinctrl):
- gpios: Should specify the gpios used for clock, command and data lines. The
gpio specifier format depends on the gpio controller.
- Pinctrl variant (preferred if available):
- pinctrl-0: Should specify pin control groups used for this controller.
- pinctrl-names: Should contain only one value - "default".
Optional Board Specific Properties:
- samsung,cd-pinmux-gpio: Specifies the card detect line that is routed
through a pinmux to the card-detect pin of the card slot. This property
should be used only if none of the mmc core card-detect properties are
used. Only for Samsung GPIO variant.
- pinctrl-0: Should specify pin control groups used for this controller.
- pinctrl-names: Should contain only one value - "default".
Example:
sdhci@12530000 {
......@@ -39,19 +22,9 @@ Example:
reg = <0x12530000 0x100>;
interrupts = <0 75 0>;
bus-width = <4>;
cd-gpios = <&gpk2 2 2 3 3>;
/* Samsung GPIO variant */
gpios = <&gpk2 0 2 0 3>, /* clock line */
<&gpk2 1 2 0 3>, /* command line */
<&gpk2 3 2 3 3>, /* data line 0 */
<&gpk2 4 2 3 3>, /* data line 1 */
<&gpk2 5 2 3 3>, /* data line 2 */
<&gpk2 6 2 3 3>; /* data line 3 */
/* Pinctrl variant */
pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>;
cd-gpios = <&gpk2 2 0>;
pinctrl-names = "default";
pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>;
};
Note: This example shows both SoC specific and board specific properties
......
......@@ -24,7 +24,6 @@
#include <linux/of_gpio.h>
#include <linux/pm.h>
#include <linux/pm_runtime.h>
#include <linux/pinctrl/consumer.h>
#include <linux/mmc/host.h>
......@@ -45,7 +44,6 @@
* @ioarea: The resource created when we claimed the IO area.
* @pdata: The platform data for this controller.
* @cur_clk: The index of the current bus clock.
* @gpios: List of gpio numbers parsed from device tree.
* @clk_io: The clock for the internal bus interface.
* @clk_bus: The clocks that are available for the SD/MMC bus clock.
*/
......@@ -57,8 +55,6 @@ struct sdhci_s3c {
unsigned int cur_clk;
int ext_cd_irq;
int ext_cd_gpio;
int *gpios;
struct pinctrl *pctrl;
struct clk *clk_io;
struct clk *clk_bus[MAX_BUS_CLK];
......@@ -447,88 +443,39 @@ static int sdhci_s3c_parse_dt(struct device *dev,
struct device_node *node = dev->of_node;
struct sdhci_s3c *ourhost = to_s3c(host);
u32 max_width;
int gpio, cnt, ret;
int gpio;
/* if the bus-width property is not specified, assume width as 1 */
if (of_property_read_u32(node, "bus-width", &max_width))
max_width = 1;
pdata->max_width = max_width;
ourhost->gpios = devm_kzalloc(dev, NUM_GPIOS(pdata->max_width) *
sizeof(int), GFP_KERNEL);
if (!ourhost->gpios)
return -ENOMEM;
/* get the card detection method */
if (of_get_property(node, "broken-cd", NULL)) {
pdata->cd_type = S3C_SDHCI_CD_NONE;
goto setup_bus;
return 0;
}
if (of_get_property(node, "non-removable", NULL)) {
pdata->cd_type = S3C_SDHCI_CD_PERMANENT;
goto setup_bus;
return 0;
}
gpio = of_get_named_gpio(node, "cd-gpios", 0);
if (gpio_is_valid(gpio)) {
pdata->cd_type = S3C_SDHCI_CD_GPIO;
goto found_cd;
} else if (gpio != -ENOENT) {
dev_err(dev, "invalid card detect gpio specified\n");
return -EINVAL;
}
gpio = of_get_named_gpio(node, "samsung,cd-pinmux-gpio", 0);
if (gpio_is_valid(gpio)) {
pdata->cd_type = S3C_SDHCI_CD_INTERNAL;
goto found_cd;
} else if (gpio != -ENOENT) {
dev_err(dev, "invalid card detect gpio specified\n");
return -EINVAL;
}
/* assuming internal card detect that will be configured by pinctrl */
pdata->cd_type = S3C_SDHCI_CD_INTERNAL;
goto setup_bus;
found_cd:
if (pdata->cd_type == S3C_SDHCI_CD_GPIO) {
pdata->ext_cd_gpio = gpio;
ourhost->ext_cd_gpio = -1;
if (of_get_property(node, "cd-inverted", NULL))
pdata->ext_cd_gpio_invert = 1;
} else if (pdata->cd_type == S3C_SDHCI_CD_INTERNAL) {
ret = devm_gpio_request(dev, gpio, "sdhci-cd");
if (ret) {
dev_err(dev, "card detect gpio request failed\n");
return -EINVAL;
}
ourhost->ext_cd_gpio = gpio;
}
setup_bus:
if (!IS_ERR(ourhost->pctrl))
return 0;
/* get the gpios for command, clock and data lines */
for (cnt = 0; cnt < NUM_GPIOS(pdata->max_width); cnt++) {
gpio = of_get_gpio(node, cnt);
if (!gpio_is_valid(gpio)) {
dev_err(dev, "invalid gpio[%d]\n", cnt);
return -EINVAL;
}
ourhost->gpios[cnt] = gpio;
}
for (cnt = 0; cnt < NUM_GPIOS(pdata->max_width); cnt++) {
ret = devm_gpio_request(dev, ourhost->gpios[cnt], "sdhci-gpio");
if (ret) {
dev_err(dev, "gpio[%d] request failed\n", cnt);
} else if (gpio != -ENOENT) {
dev_err(dev, "invalid card detect gpio specified\n");
return -EINVAL;
}
}
/* assuming internal card detect that will be configured by pinctrl */
pdata->cd_type = S3C_SDHCI_CD_INTERNAL;
return 0;
}
#else
......@@ -589,8 +536,6 @@ static int sdhci_s3c_probe(struct platform_device *pdev)
goto err_pdata_io_clk;
}
sc->pctrl = devm_pinctrl_get_select_default(&pdev->dev);
if (pdev->dev.of_node) {
ret = sdhci_s3c_parse_dt(&pdev->dev, host, pdata);
if (ret)
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册