提交 c08b7b3e 编写于 作者: E Eric Miao 提交者: Russell King

[ARM] 4435/1: PXA: remove PXA_INTERNAL_IRQS

1. define PXA_GPIO_IRQ_BASE to be right after the internal IRQs,
   and define PXA_GPIO_IRQ_NUM to be 128 for all PXA2xx variants

2. make the code specific to the high IRQ numbers (32..64) to be
   PXA27x specific

3. add a function pxa_init_irq_high() to initialize the internal
   high IRQ chip, the invoke of this function could be moved to
   PXA27x specific initialization code
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
上级 486c9551
......@@ -67,7 +67,7 @@ static struct irq_chip pxa_internal_chip_low = {
.set_wake = pxa_set_wake,
};
#if PXA_INTERNAL_IRQS > 32
#ifdef CONFIG_PXA27x
/*
* This is for the second set of internal IRQs as found on the PXA27x.
......@@ -90,6 +90,19 @@ static struct irq_chip pxa_internal_chip_high = {
.unmask = pxa_unmask_high_irq,
};
void __init pxa_init_irq_high(void)
{
int irq;
ICMR2 = 0;
ICLR2 = 0;
for (irq = PXA_IRQ(32); irq < PXA_IRQ(64); irq++) {
set_irq_chip(irq, &pxa_internal_chip_high);
set_irq_handler(irq, handle_level_irq);
set_irq_flags(irq, IRQF_VALID);
}
}
#endif
/* Note that if an input/irq line ever gets changed to an output during
......@@ -314,7 +327,6 @@ static struct irq_chip pxa_muxed_gpio_chip = {
.set_wake = pxa_set_gpio_wake,
};
void __init pxa_init_irq(void)
{
int irq;
......@@ -338,8 +350,6 @@ void __init pxa_init_irq(void)
#ifdef CONFIG_PXA27x
/* And similarly for the extra regs on the PXA27x */
ICMR2 = 0;
ICLR2 = 0;
GFER3 = 0;
GRER3 = 0;
GEDR3 = GEDR3;
......@@ -357,12 +367,8 @@ void __init pxa_init_irq(void)
set_irq_flags(irq, IRQF_VALID);
}
#if PXA_INTERNAL_IRQS > 32
for (irq = PXA_IRQ(32); irq < PXA_IRQ(PXA_INTERNAL_IRQS); irq++) {
set_irq_chip(irq, &pxa_internal_chip_high);
set_irq_handler(irq, handle_level_irq);
set_irq_flags(irq, IRQF_VALID);
}
#ifdef CONFIG_PXA27x
pxa_init_irq_high();
#endif
for (irq = IRQ_GPIO0; irq <= IRQ_GPIO1; irq++) {
......
......@@ -55,18 +55,15 @@
#ifdef CONFIG_PXA27x
#define IRQ_TPM PXA_IRQ(32) /* TPM interrupt */
#define IRQ_CAMERA PXA_IRQ(33) /* Camera Interface */
#define PXA_INTERNAL_IRQS 34
#else
#define PXA_INTERNAL_IRQS 32
#endif
#define GPIO_2_x_TO_IRQ(x) \
PXA_IRQ((x) - 2 + PXA_INTERNAL_IRQS)
#define PXA_GPIO_IRQ_BASE (64)
#define PXA_GPIO_IRQ_NUM (128)
#define GPIO_2_x_TO_IRQ(x) (PXA_GPIO_IRQ_BASE + (x))
#define IRQ_GPIO(x) (((x) < 2) ? (IRQ_GPIO0 + (x)) : GPIO_2_x_TO_IRQ(x))
#define IRQ_TO_GPIO_2_x(i) \
((i) - IRQ_GPIO(2) + 2)
#define IRQ_TO_GPIO_2_x(i) ((i) - PXA_GPIO_IRQ_BASE)
#define IRQ_TO_GPIO(i) (((i) < IRQ_GPIO(2)) ? ((i) - IRQ_GPIO0) : IRQ_TO_GPIO_2_x(i))
#if defined(CONFIG_PXA25x)
......@@ -81,7 +78,7 @@
* these. If you need more, increase IRQ_BOARD_END, but keep it
* within sensible limits.
*/
#define IRQ_BOARD_START (IRQ_GPIO(PXA_LAST_GPIO) + 1)
#define IRQ_BOARD_START (PXA_GPIO_IRQ_BASE + PXA_GPIO_IRQ_NUM)
#define IRQ_BOARD_END (IRQ_BOARD_START + 16)
#define IRQ_SA1111_START (IRQ_BOARD_END)
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册