提交 accb1eb5 编写于 作者: J Jani Nikula

drm/i915/dvo: switch to kernel unsigned int types

We have fairly mixed uintN_t vs. uN usage throughout the driver, but try
to stick to kernel types at least where it's more prevalent.

v2: fix checkpatch warning on indentation
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612095621.21101-1-jani.nikula@intel.com
上级 93383b57
......@@ -159,7 +159,7 @@
#define CH7017_BANG_LIMIT_CONTROL 0x7f
struct ch7017_priv {
uint8_t dummy;
u8 dummy;
};
static void ch7017_dump_regs(struct intel_dvo_device *dvo);
......@@ -186,7 +186,7 @@ static bool ch7017_read(struct intel_dvo_device *dvo, u8 addr, u8 *val)
static bool ch7017_write(struct intel_dvo_device *dvo, u8 addr, u8 val)
{
uint8_t buf[2] = { addr, val };
u8 buf[2] = { addr, val };
struct i2c_msg msg = {
.addr = dvo->slave_addr,
.flags = 0,
......@@ -258,11 +258,11 @@ static void ch7017_mode_set(struct intel_dvo_device *dvo,
const struct drm_display_mode *mode,
const struct drm_display_mode *adjusted_mode)
{
uint8_t lvds_pll_feedback_div, lvds_pll_vco_control;
uint8_t outputs_enable, lvds_control_2, lvds_power_down;
uint8_t horizontal_active_pixel_input;
uint8_t horizontal_active_pixel_output, vertical_active_line_output;
uint8_t active_input_line_output;
u8 lvds_pll_feedback_div, lvds_pll_vco_control;
u8 outputs_enable, lvds_control_2, lvds_power_down;
u8 horizontal_active_pixel_input;
u8 horizontal_active_pixel_output, vertical_active_line_output;
u8 active_input_line_output;
DRM_DEBUG_KMS("Registers before mode setting\n");
ch7017_dump_regs(dvo);
......@@ -333,7 +333,7 @@ static void ch7017_mode_set(struct intel_dvo_device *dvo,
/* set the CH7017 power state */
static void ch7017_dpms(struct intel_dvo_device *dvo, bool enable)
{
uint8_t val;
u8 val;
ch7017_read(dvo, CH7017_LVDS_POWER_DOWN, &val);
......@@ -361,7 +361,7 @@ static void ch7017_dpms(struct intel_dvo_device *dvo, bool enable)
static bool ch7017_get_hw_state(struct intel_dvo_device *dvo)
{
uint8_t val;
u8 val;
ch7017_read(dvo, CH7017_LVDS_POWER_DOWN, &val);
......@@ -373,7 +373,7 @@ static bool ch7017_get_hw_state(struct intel_dvo_device *dvo)
static void ch7017_dump_regs(struct intel_dvo_device *dvo)
{
uint8_t val;
u8 val;
#define DUMP(reg) \
do { \
......
......@@ -85,7 +85,7 @@ SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
*/
static struct ch7xxx_id_struct {
uint8_t vid;
u8 vid;
char *name;
} ch7xxx_ids[] = {
{ CH7011_VID, "CH7011" },
......@@ -96,7 +96,7 @@ static struct ch7xxx_id_struct {
};
static struct ch7xxx_did_struct {
uint8_t did;
u8 did;
char *name;
} ch7xxx_dids[] = {
{ CH7xxx_DID, "CH7XXX" },
......@@ -107,7 +107,7 @@ struct ch7xxx_priv {
bool quiet;
};
static char *ch7xxx_get_id(uint8_t vid)
static char *ch7xxx_get_id(u8 vid)
{
int i;
......@@ -119,7 +119,7 @@ static char *ch7xxx_get_id(uint8_t vid)
return NULL;
}
static char *ch7xxx_get_did(uint8_t did)
static char *ch7xxx_get_did(u8 did)
{
int i;
......@@ -132,7 +132,7 @@ static char *ch7xxx_get_did(uint8_t did)
}
/** Reads an 8 bit register */
static bool ch7xxx_readb(struct intel_dvo_device *dvo, int addr, uint8_t *ch)
static bool ch7xxx_readb(struct intel_dvo_device *dvo, int addr, u8 *ch)
{
struct ch7xxx_priv *ch7xxx = dvo->dev_priv;
struct i2c_adapter *adapter = dvo->i2c_bus;
......@@ -170,11 +170,11 @@ static bool ch7xxx_readb(struct intel_dvo_device *dvo, int addr, uint8_t *ch)
}
/** Writes an 8 bit register */
static bool ch7xxx_writeb(struct intel_dvo_device *dvo, int addr, uint8_t ch)
static bool ch7xxx_writeb(struct intel_dvo_device *dvo, int addr, u8 ch)
{
struct ch7xxx_priv *ch7xxx = dvo->dev_priv;
struct i2c_adapter *adapter = dvo->i2c_bus;
uint8_t out_buf[2];
u8 out_buf[2];
struct i2c_msg msg = {
.addr = dvo->slave_addr,
.flags = 0,
......@@ -201,7 +201,7 @@ static bool ch7xxx_init(struct intel_dvo_device *dvo,
{
/* this will detect the CH7xxx chip on the specified i2c bus */
struct ch7xxx_priv *ch7xxx;
uint8_t vendor, device;
u8 vendor, device;
char *name, *devid;
ch7xxx = kzalloc(sizeof(struct ch7xxx_priv), GFP_KERNEL);
......@@ -244,7 +244,7 @@ static bool ch7xxx_init(struct intel_dvo_device *dvo,
static enum drm_connector_status ch7xxx_detect(struct intel_dvo_device *dvo)
{
uint8_t cdet, orig_pm, pm;
u8 cdet, orig_pm, pm;
ch7xxx_readb(dvo, CH7xxx_PM, &orig_pm);
......@@ -276,7 +276,7 @@ static void ch7xxx_mode_set(struct intel_dvo_device *dvo,
const struct drm_display_mode *mode,
const struct drm_display_mode *adjusted_mode)
{
uint8_t tvco, tpcp, tpd, tlpf, idf;
u8 tvco, tpcp, tpd, tlpf, idf;
if (mode->clock <= 65000) {
tvco = 0x23;
......@@ -336,7 +336,7 @@ static void ch7xxx_dump_regs(struct intel_dvo_device *dvo)
int i;
for (i = 0; i < CH7xxx_NUM_REGS; i++) {
uint8_t val;
u8 val;
if ((i % 8) == 0)
DRM_DEBUG_KMS("\n %02X: ", i);
ch7xxx_readb(dvo, i, &val);
......
......@@ -161,7 +161,7 @@
* instead. The following list contains all registers that
* require saving.
*/
static const uint16_t backup_addresses[] = {
static const u16 backup_addresses[] = {
0x11, 0x12,
0x18, 0x19, 0x1a, 0x1f,
0x20, 0x21, 0x22, 0x23, 0x24, 0x25, 0x26, 0x27,
......@@ -174,11 +174,11 @@ static const uint16_t backup_addresses[] = {
struct ivch_priv {
bool quiet;
uint16_t width, height;
u16 width, height;
/* Register backup */
uint16_t reg_backup[ARRAY_SIZE(backup_addresses)];
u16 reg_backup[ARRAY_SIZE(backup_addresses)];
};
......@@ -188,7 +188,7 @@ static void ivch_dump_regs(struct intel_dvo_device *dvo);
*
* Each of the 256 registers are 16 bits long.
*/
static bool ivch_read(struct intel_dvo_device *dvo, int addr, uint16_t *data)
static bool ivch_read(struct intel_dvo_device *dvo, int addr, u16 *data)
{
struct ivch_priv *priv = dvo->dev_priv;
struct i2c_adapter *adapter = dvo->i2c_bus;
......@@ -231,7 +231,7 @@ static bool ivch_read(struct intel_dvo_device *dvo, int addr, uint16_t *data)
}
/* Writes a 16-bit register on the ivch */
static bool ivch_write(struct intel_dvo_device *dvo, int addr, uint16_t data)
static bool ivch_write(struct intel_dvo_device *dvo, int addr, u16 data)
{
struct ivch_priv *priv = dvo->dev_priv;
struct i2c_adapter *adapter = dvo->i2c_bus;
......@@ -263,7 +263,7 @@ static bool ivch_init(struct intel_dvo_device *dvo,
struct i2c_adapter *adapter)
{
struct ivch_priv *priv;
uint16_t temp;
u16 temp;
int i;
priv = kzalloc(sizeof(struct ivch_priv), GFP_KERNEL);
......@@ -342,7 +342,7 @@ static void ivch_reset(struct intel_dvo_device *dvo)
static void ivch_dpms(struct intel_dvo_device *dvo, bool enable)
{
int i;
uint16_t vr01, vr30, backlight;
u16 vr01, vr30, backlight;
ivch_reset(dvo);
......@@ -379,7 +379,7 @@ static void ivch_dpms(struct intel_dvo_device *dvo, bool enable)
static bool ivch_get_hw_state(struct intel_dvo_device *dvo)
{
uint16_t vr01;
u16 vr01;
ivch_reset(dvo);
......@@ -398,9 +398,9 @@ static void ivch_mode_set(struct intel_dvo_device *dvo,
const struct drm_display_mode *adjusted_mode)
{
struct ivch_priv *priv = dvo->dev_priv;
uint16_t vr40 = 0;
uint16_t vr01 = 0;
uint16_t vr10;
u16 vr40 = 0;
u16 vr01 = 0;
u16 vr10;
ivch_reset(dvo);
......@@ -416,7 +416,7 @@ static void ivch_mode_set(struct intel_dvo_device *dvo,
if (mode->hdisplay != adjusted_mode->crtc_hdisplay ||
mode->vdisplay != adjusted_mode->crtc_vdisplay) {
uint16_t x_ratio, y_ratio;
u16 x_ratio, y_ratio;
vr01 |= VR01_PANEL_FIT_ENABLE;
vr40 |= VR40_CLOCK_GATING_ENABLE;
......@@ -438,7 +438,7 @@ static void ivch_mode_set(struct intel_dvo_device *dvo,
static void ivch_dump_regs(struct intel_dvo_device *dvo)
{
uint16_t val;
u16 val;
ivch_read(dvo, VR00, &val);
DRM_DEBUG_KMS("VR00: 0x%04x\n", val);
......
......@@ -191,8 +191,8 @@ enum {
};
struct ns2501_reg {
uint8_t offset;
uint8_t value;
u8 offset;
u8 value;
};
/*
......@@ -202,23 +202,23 @@ struct ns2501_reg {
* read all this with a grain of salt.
*/
struct ns2501_configuration {
uint8_t sync; /* configuration of the C0 register */
uint8_t conf; /* configuration register 8 */
uint8_t syncb; /* configuration register 41 */
uint8_t dither; /* configuration of the dithering */
uint8_t pll_a; /* PLL configuration, register A, 1B */
uint16_t pll_b; /* PLL configuration, register B, 1C/1D */
uint16_t hstart; /* horizontal start, registers C1/C2 */
uint16_t hstop; /* horizontal total, registers C3/C4 */
uint16_t vstart; /* vertical start, registers C5/C6 */
uint16_t vstop; /* vertical total, registers C7/C8 */
uint16_t vsync; /* manual vertical sync start, 80/81 */
uint16_t vtotal; /* number of lines generated, 82/83 */
uint16_t hpos; /* horizontal position + 256, 98/99 */
uint16_t vpos; /* vertical position, 8e/8f */
uint16_t voffs; /* vertical output offset, 9c/9d */
uint16_t hscale; /* horizontal scaling factor, b8/b9 */
uint16_t vscale; /* vertical scaling factor, 10/11 */
u8 sync; /* configuration of the C0 register */
u8 conf; /* configuration register 8 */
u8 syncb; /* configuration register 41 */
u8 dither; /* configuration of the dithering */
u8 pll_a; /* PLL configuration, register A, 1B */
u16 pll_b; /* PLL configuration, register B, 1C/1D */
u16 hstart; /* horizontal start, registers C1/C2 */
u16 hstop; /* horizontal total, registers C3/C4 */
u16 vstart; /* vertical start, registers C5/C6 */
u16 vstop; /* vertical total, registers C7/C8 */
u16 vsync; /* manual vertical sync start, 80/81 */
u16 vtotal; /* number of lines generated, 82/83 */
u16 hpos; /* horizontal position + 256, 98/99 */
u16 vpos; /* vertical position, 8e/8f */
u16 voffs; /* vertical output offset, 9c/9d */
u16 hscale; /* horizontal scaling factor, b8/b9 */
u16 vscale; /* vertical scaling factor, 10/11 */
};
/*
......@@ -389,7 +389,7 @@ struct ns2501_priv {
** If it returns false, it might be wise to enable the
** DVO with the above function.
*/
static bool ns2501_readb(struct intel_dvo_device *dvo, int addr, uint8_t * ch)
static bool ns2501_readb(struct intel_dvo_device *dvo, int addr, u8 *ch)
{
struct ns2501_priv *ns = dvo->dev_priv;
struct i2c_adapter *adapter = dvo->i2c_bus;
......@@ -434,11 +434,11 @@ static bool ns2501_readb(struct intel_dvo_device *dvo, int addr, uint8_t * ch)
** If it returns false, it might be wise to enable the
** DVO with the above function.
*/
static bool ns2501_writeb(struct intel_dvo_device *dvo, int addr, uint8_t ch)
static bool ns2501_writeb(struct intel_dvo_device *dvo, int addr, u8 ch)
{
struct ns2501_priv *ns = dvo->dev_priv;
struct i2c_adapter *adapter = dvo->i2c_bus;
uint8_t out_buf[2];
u8 out_buf[2];
struct i2c_msg msg = {
.addr = dvo->slave_addr,
......
......@@ -65,7 +65,7 @@ struct sil164_priv {
#define SILPTR(d) ((SIL164Ptr)(d->DriverPrivate.ptr))
static bool sil164_readb(struct intel_dvo_device *dvo, int addr, uint8_t *ch)
static bool sil164_readb(struct intel_dvo_device *dvo, int addr, u8 *ch)
{
struct sil164_priv *sil = dvo->dev_priv;
struct i2c_adapter *adapter = dvo->i2c_bus;
......@@ -102,11 +102,11 @@ static bool sil164_readb(struct intel_dvo_device *dvo, int addr, uint8_t *ch)
return false;
}
static bool sil164_writeb(struct intel_dvo_device *dvo, int addr, uint8_t ch)
static bool sil164_writeb(struct intel_dvo_device *dvo, int addr, u8 ch)
{
struct sil164_priv *sil = dvo->dev_priv;
struct i2c_adapter *adapter = dvo->i2c_bus;
uint8_t out_buf[2];
u8 out_buf[2];
struct i2c_msg msg = {
.addr = dvo->slave_addr,
.flags = 0,
......@@ -173,7 +173,7 @@ static bool sil164_init(struct intel_dvo_device *dvo,
static enum drm_connector_status sil164_detect(struct intel_dvo_device *dvo)
{
uint8_t reg9;
u8 reg9;
sil164_readb(dvo, SIL164_REG9, &reg9);
......@@ -243,7 +243,7 @@ static bool sil164_get_hw_state(struct intel_dvo_device *dvo)
static void sil164_dump_regs(struct intel_dvo_device *dvo)
{
uint8_t val;
u8 val;
sil164_readb(dvo, SIL164_FREQ_LO, &val);
DRM_DEBUG_KMS("SIL164_FREQ_LO: 0x%02x\n", val);
......
......@@ -90,7 +90,7 @@ struct tfp410_priv {
bool quiet;
};
static bool tfp410_readb(struct intel_dvo_device *dvo, int addr, uint8_t *ch)
static bool tfp410_readb(struct intel_dvo_device *dvo, int addr, u8 *ch)
{
struct tfp410_priv *tfp = dvo->dev_priv;
struct i2c_adapter *adapter = dvo->i2c_bus;
......@@ -127,11 +127,11 @@ static bool tfp410_readb(struct intel_dvo_device *dvo, int addr, uint8_t *ch)
return false;
}
static bool tfp410_writeb(struct intel_dvo_device *dvo, int addr, uint8_t ch)
static bool tfp410_writeb(struct intel_dvo_device *dvo, int addr, u8 ch)
{
struct tfp410_priv *tfp = dvo->dev_priv;
struct i2c_adapter *adapter = dvo->i2c_bus;
uint8_t out_buf[2];
u8 out_buf[2];
struct i2c_msg msg = {
.addr = dvo->slave_addr,
.flags = 0,
......@@ -155,7 +155,7 @@ static bool tfp410_writeb(struct intel_dvo_device *dvo, int addr, uint8_t ch)
static int tfp410_getid(struct intel_dvo_device *dvo, int addr)
{
uint8_t ch1, ch2;
u8 ch1, ch2;
if (tfp410_readb(dvo, addr+0, &ch1) &&
tfp410_readb(dvo, addr+1, &ch2))
......@@ -203,7 +203,7 @@ static bool tfp410_init(struct intel_dvo_device *dvo,
static enum drm_connector_status tfp410_detect(struct intel_dvo_device *dvo)
{
enum drm_connector_status ret = connector_status_disconnected;
uint8_t ctl2;
u8 ctl2;
if (tfp410_readb(dvo, TFP410_CTL_2, &ctl2)) {
if (ctl2 & TFP410_CTL_2_RSEN)
......@@ -236,7 +236,7 @@ static void tfp410_mode_set(struct intel_dvo_device *dvo,
/* set the tfp410 power state */
static void tfp410_dpms(struct intel_dvo_device *dvo, bool enable)
{
uint8_t ctl1;
u8 ctl1;
if (!tfp410_readb(dvo, TFP410_CTL_1, &ctl1))
return;
......@@ -251,7 +251,7 @@ static void tfp410_dpms(struct intel_dvo_device *dvo, bool enable)
static bool tfp410_get_hw_state(struct intel_dvo_device *dvo)
{
uint8_t ctl1;
u8 ctl1;
if (!tfp410_readb(dvo, TFP410_CTL_1, &ctl1))
return false;
......@@ -264,7 +264,7 @@ static bool tfp410_get_hw_state(struct intel_dvo_device *dvo)
static void tfp410_dump_regs(struct intel_dvo_device *dvo)
{
uint8_t val, val2;
u8 val, val2;
tfp410_readb(dvo, TFP410_REV, &val);
DRM_DEBUG_KMS("TFP410_REV: 0x%02X\n", val);
......
......@@ -438,7 +438,7 @@ void intel_dvo_init(struct drm_i915_private *dev_priv)
int gpio;
bool dvoinit;
enum pipe pipe;
uint32_t dpll[I915_MAX_PIPES];
u32 dpll[I915_MAX_PIPES];
enum port port;
/*
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册