drm/loongson: add kernel modesetting driver support for ls7a1000/ls7a2000

LoongArch inclusion
category: feature
bugzilla: https://gitee.com/openeuler/kernel/issues/I6BWFP

--------------------------------

 1) Support Double Screen HW Cursor
 2) Support LS7A1000/LS7A2000 + 3A5000
 3) CRTC's DMA Step is remain 256 bytes

Change-Id: Id3c3a7bebf1e95dcc882f69ba20ff3b7e57d275d
Signed-off-by: NJingfeng Sui <suijingfeng@loongson.cn>
Signed-off-by: NHuacai Chen <chenhuacai@loongson.cn>
(cherry picked from commit 80764bc7)

arch/loongarch/configs/loongson3_defconfig

@@ -594,6 +594,7 @@ CONFIG_DRM_AMDGPU_SI=y
 CONFIG_DRM_AMDGPU_CIK=y
 CONFIG_DRM_AMDGPU_USERPTR=y
 CONFIG_DRM_AST=y
+CONFIG_DRM_LOONGSON=y
 CONFIG_DRM_QXL=m
 CONFIG_DRM_VIRTIO_GPU=m
 CONFIG_FB_EFI=y

drivers/gpu/drm/Kconfig

@@ -312,6 +312,8 @@ source "drivers/gpu/drm/udl/Kconfig"
 
 source "drivers/gpu/drm/ast/Kconfig"
 
+source "drivers/gpu/drm/loongson/Kconfig"
+
 source "drivers/gpu/drm/mgag200/Kconfig"
 
 source "drivers/gpu/drm/armada/Kconfig"

drivers/gpu/drm/Makefile

@@ -86,6 +86,7 @@ obj-$(CONFIG_DRM_ROCKCHIP) +=rockchip/
 obj-$(CONFIG_DRM_GMA500) += gma500/
 obj-$(CONFIG_DRM_UDL) += udl/
 obj-$(CONFIG_DRM_AST) += ast/
+obj-$(CONFIG_DRM_LOONGSON) +=loongson/
 obj-$(CONFIG_DRM_ARMADA) += armada/
 obj-$(CONFIG_DRM_ATMEL_HLCDC)	+= atmel-hlcdc/
 obj-y			+= rcar-du/

drivers/gpu/drm/loongson/Kconfig

+# SPDX-License-Identifier: GPL-2.0
+
+config DRM_LOONGSON
+	tristate "DRM Support for loongson's display controller"
+	depends on DRM && PCI
+	depends on MACH_LOONGSON64 || LOONGARCH || MIPS || COMPILE_TEST
+	select OF
+	select CMA if HAVE_DMA_CONTIGUOUS
+	select DMA_CMA if HAVE_DMA_CONTIGUOUS
+	select DRM_KMS_HELPER
+	select DRM_KMS_FB_HELPER
+	select DRM_KMS_CMA_HELPER
+	select DRM_GEM_CMA_HELPER
+	select DRM_TTM
+	select DRM_TTM_HELPER
+	select DRM_VRAM_HELPER
+	select VIDEOMODE_HELPERS
+	select DRM_BRIDGE
+	select DRM_PANEL_BRIDGE
+	default y
+	help
+	  This is a KMS driver for the display controller in the LS7A1000
+	  bridge chip and LS2K1000/LS2K0500 SoC.
+	  If "M" is selected, the module will be called loongson.
+
+	  If in doubt, say "Y".

drivers/gpu/drm/loongson/Makefile

+# SPDX-License-Identifier: GPL-2.0
+
+loongson-y := \
+	lsdc_drv.o \
+	lsdc_crtc.o \
+	lsdc_irq.o \
+	lsdc_plane.o \
+	lsdc_pll.o \
+	lsdc_i2c.o \
+	lsdc_output.o \
+	lsdc_pci_drv.o \
+	lsdc_debugfs.o \
+
+lsdc-$(CONFIG_DEBUG_FS) += lsdc_debugfs.o
+
+obj-$(CONFIG_DRM_LOONGSON) += loongson.o

drivers/gpu/drm/loongson/lsdc_crtc.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Loongson Corporation
+ */
+
+/*
+ * Authors:
+ *      Sui Jingfeng <suijingfeng@loongson.cn>
+ */
+#include <drm/drm_vblank.h>
+#include <drm/drm_atomic.h>
+#include <drm/drm_atomic_helper.h>
+
+#include "lsdc_drv.h"
+#include "lsdc_regs.h"
+#include "lsdc_pll.h"
+
+static int lsdc_crtc_enable_vblank(struct drm_crtc *crtc)
+{
+	struct lsdc_device *ldev = to_lsdc(crtc->dev);
+	unsigned int index = drm_crtc_index(crtc);
+	struct drm_crtc_state *state = crtc->state;
+	u32 val;
+
+	if (state->enable) {
+		val = readl(ldev->reg_base + LSDC_INT_REG);
+
+		if (index == 0)
+			val |= INT_CRTC0_VS_EN;
+		else if (index == 1)
+			val |= INT_CRTC1_VS_EN;
+
+		writel(val, ldev->reg_base + LSDC_INT_REG);
+	}
+
+	return 0;
+}
+
+static void lsdc_crtc_disable_vblank(struct drm_crtc *crtc)
+{
+	struct lsdc_device *ldev = to_lsdc(crtc->dev);
+	unsigned int index = drm_crtc_index(crtc);
+	u32 val;
+
+	val = readl(ldev->reg_base + LSDC_INT_REG);
+
+	if (index == 0)
+		val &= ~INT_CRTC0_VS_EN;
+	else if (index == 1)
+		val &= ~INT_CRTC1_VS_EN;
+
+	writel(val, ldev->reg_base + LSDC_INT_REG);
+}
+
+static void lsdc_crtc_reset(struct drm_crtc *crtc)
+{
+	struct drm_device *ddev = crtc->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	unsigned int index = drm_crtc_index(crtc);
+	struct lsdc_crtc_state *priv_crtc_state;
+	u32 val = CFG_RESET_BIT | CFG_OUTPUT_EN_BIT | LSDC_PF_XRGB8888;
+
+	if (ldev->enable_gamma)
+		val |= CFG_GAMMAR_EN_BIT;
+
+	/* align to 64 */
+	if (ldev->desc->chip == LSDC_CHIP_7A2000) {
+		val &= ~LS7A2000_DMA_STEP_MASK;
+		val |= DMA_STEP_256_BYTE;
+	}
+
+	if (index == 0)
+		writel(val, ldev->reg_base + LSDC_CRTC0_CFG_REG);
+	else if (index == 1)
+		writel(val, ldev->reg_base + LSDC_CRTC1_CFG_REG);
+
+	if (crtc->state) {
+		priv_crtc_state = to_lsdc_crtc_state(crtc->state);
+		__drm_atomic_helper_crtc_destroy_state(&priv_crtc_state->base);
+		kfree(priv_crtc_state);
+	}
+
+	priv_crtc_state = kzalloc(sizeof(*priv_crtc_state), GFP_KERNEL);
+	if (!priv_crtc_state)
+		return;
+
+	__drm_atomic_helper_crtc_reset(crtc, &priv_crtc_state->base);
+
+	drm_dbg(ddev, "crtc%u reset\n", index);
+}
+
+static void lsdc_crtc_atomic_destroy_state(struct drm_crtc *crtc, struct drm_crtc_state *state)
+{
+	struct lsdc_crtc_state *priv_crtc_state = to_lsdc_crtc_state(state);
+
+	__drm_atomic_helper_crtc_destroy_state(&priv_crtc_state->base);
+
+	kfree(priv_crtc_state);
+}
+
+static struct drm_crtc_state *lsdc_crtc_atomic_duplicate_state(struct drm_crtc *crtc)
+{
+	struct lsdc_crtc_state *new_priv_state;
+	struct lsdc_crtc_state *old_priv_state;
+	struct drm_device *ddev = crtc->dev;
+
+	if (drm_WARN_ON(ddev, !crtc->state))
+		return NULL;
+
+	new_priv_state = kmalloc(sizeof(*new_priv_state), GFP_KERNEL);
+	if (!new_priv_state)
+		return NULL;
+
+	__drm_atomic_helper_crtc_duplicate_state(crtc, &new_priv_state->base);
+
+	old_priv_state = to_lsdc_crtc_state(crtc->state);
+
+	memcpy(&new_priv_state->pparams, &old_priv_state->pparams, sizeof(new_priv_state->pparams));
+
+	return &new_priv_state->base;
+}
+
+static const struct drm_crtc_funcs lsdc_crtc_funcs = {
+	.reset = lsdc_crtc_reset,
+	.destroy = drm_crtc_cleanup,
+	.set_config = drm_atomic_helper_set_config,
+	.page_flip = drm_atomic_helper_page_flip,
+	.atomic_duplicate_state = lsdc_crtc_atomic_duplicate_state,
+	.atomic_destroy_state = lsdc_crtc_atomic_destroy_state,
+	.enable_vblank = lsdc_crtc_enable_vblank,
+	.disable_vblank = lsdc_crtc_disable_vblank,
+};
+
+static enum drm_mode_status
+lsdc_crtc_helper_mode_valid(struct drm_crtc *crtc,
+			    const struct drm_display_mode *mode)
+{
+	struct drm_device *ddev = crtc->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	const struct lsdc_chip_desc * const descp = ldev->desc;
+
+	if (mode->hdisplay > descp->max_width)
+		return MODE_BAD_HVALUE;
+	if (mode->vdisplay > descp->max_height)
+		return MODE_BAD_VVALUE;
+
+	if (mode->clock > descp->max_pixel_clk) {
+		drm_dbg(ddev, "mode %dx%d, pixel clock=%d is too high\n",
+			mode->hdisplay, mode->vdisplay, mode->clock);
+		return MODE_CLOCK_HIGH;
+	}
+
+	/* The CRTC hardware dma take 256 bytes once a time,
+	 * this is a limitation of the CRTC.
+	 * TODO: check RGB565 support
+	 */
+	if (!ldev->relax_alignment) {
+		if ((mode->hdisplay * 4) % descp->stride_alignment) {
+			drm_dbg(ddev, "mode %dx%d, stride is not %u bytes aligned\n",
+				mode->hdisplay, mode->vdisplay, descp->stride_alignment);
+			return MODE_BAD;
+		}
+	}
+
+	return MODE_OK;
+}
+
+static int lsdc_pixpll_atomic_check(struct drm_crtc *crtc,
+				    struct drm_crtc_state *state)
+{
+	struct lsdc_display_pipe * const dispipe = drm_crtc_to_dispipe(crtc);
+	struct lsdc_pll * const pixpll = &dispipe->pixpll;
+	const struct lsdc_pixpll_funcs * const pfuncs = pixpll->funcs;
+	struct lsdc_crtc_state *priv_state = to_lsdc_crtc_state(state);
+	bool ret;
+
+	ret = pfuncs->compute(pixpll, state->mode.clock, &priv_state->pparams);
+	if (ret)
+		return 0;
+
+	drm_warn(crtc->dev, "failed find PLL parameters for %u\n", state->mode.clock);
+
+	return -EINVAL;
+}
+
+static int lsdc_crtc_helper_atomic_check(struct drm_crtc *crtc,
+					 struct drm_crtc_state *state)
+{
+	if (!state->enable)
+		return 0; /* no mode checks if CRTC is being disabled */
+
+	if (state->mode_changed || state->active_changed || state->connectors_changed)
+		return lsdc_pixpll_atomic_check(crtc, state);
+
+	return 0;
+}
+
+static void lsdc_update_pixclk(struct drm_crtc *crtc)
+{
+	struct lsdc_display_pipe * const dispipe = drm_crtc_to_dispipe(crtc);
+	struct lsdc_pll * const pixpll = &dispipe->pixpll;
+	const struct lsdc_pixpll_funcs * const clkfun = pixpll->funcs;
+	struct lsdc_crtc_state *priv_state = to_lsdc_crtc_state(crtc->state);
+
+	clkfun->update(pixpll, &priv_state->pparams);
+}
+
+static void lsdc_crtc_helper_mode_set_nofb(struct drm_crtc *crtc)
+{
+	struct drm_device *ddev = crtc->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	struct drm_display_mode *mode = &crtc->state->adjusted_mode;
+	unsigned int index = drm_crtc_index(crtc);
+	u32 h_sync, v_sync, h_val, v_val;
+
+	/* 26:16 total pixels, 10:0 visiable pixels, in horizontal */
+	h_val = (mode->crtc_htotal << 16) | mode->crtc_hdisplay;
+	/* Hack to support non 256 bytes aligned stride, for example:
+	 * 800x480 DPI panel. In this case userspace do the work to
+	 * guarantee the horizontal pixel size is aligned by padding it.
+	 * In actual, We allocate 832x480x4 bytes in size.
+	 */
+	if (ldev->relax_alignment)
+		h_val = (h_val + 63) & ~63;
+
+	/* 26:16 total pixels, 10:0 visiable pixels, in vertical */
+	v_val = (mode->crtc_vtotal << 16) | mode->crtc_vdisplay;
+	/* 26:16 hsync end, 10:0 hsync start, bit 30 is hsync enable */
+	h_sync = (mode->crtc_hsync_end << 16) | mode->crtc_hsync_start | EN_HSYNC_BIT;
+	if (mode->flags & DRM_MODE_FLAG_NHSYNC)
+		h_sync |= INV_HSYNC_BIT;
+
+	/* 26:16 vsync end, 10:0 vsync start, bit 30 is vsync enable */
+	v_sync = (mode->crtc_vsync_end << 16) | mode->crtc_vsync_start | EN_VSYNC_BIT;
+	if (mode->flags & DRM_MODE_FLAG_NVSYNC)
+		v_sync |= INV_VSYNC_BIT;
+
+	if (index == 0) {
+		writel(0, ldev->reg_base + LSDC_CRTC0_FB_ORIGIN_REG);
+		writel(h_val, ldev->reg_base + LSDC_CRTC0_HDISPLAY_REG);
+		writel(v_val, ldev->reg_base + LSDC_CRTC0_VDISPLAY_REG);
+		writel(h_sync, ldev->reg_base + LSDC_CRTC0_HSYNC_REG);
+		writel(v_sync, ldev->reg_base + LSDC_CRTC0_VSYNC_REG);
+	} else if (index == 1) {
+		writel(0, ldev->reg_base + LSDC_CRTC1_FB_ORIGIN_REG);
+		writel(h_val, ldev->reg_base + LSDC_CRTC1_HDISPLAY_REG);
+		writel(v_val, ldev->reg_base + LSDC_CRTC1_VDISPLAY_REG);
+		writel(h_sync, ldev->reg_base + LSDC_CRTC1_HSYNC_REG);
+		writel(v_sync, ldev->reg_base + LSDC_CRTC1_VSYNC_REG);
+	}
+
+	drm_dbg(ddev, "%s modeset: %ux%u\n", crtc->name, mode->hdisplay, mode->vdisplay);
+
+	lsdc_update_pixclk(crtc);
+}
+
+static void lsdc_enable_display(struct lsdc_device *ldev, unsigned int index)
+{
+	u32 val;
+
+	if (index == 0) {
+		val = readl(ldev->reg_base + LSDC_CRTC0_CFG_REG);
+		val |= CFG_OUTPUT_EN_BIT;
+		writel(val, ldev->reg_base + LSDC_CRTC0_CFG_REG);
+	} else if (index == 1) {
+		val = readl(ldev->reg_base + LSDC_CRTC1_CFG_REG);
+		val |= CFG_OUTPUT_EN_BIT;
+		writel(val, ldev->reg_base + LSDC_CRTC1_CFG_REG);
+	}
+}
+
+static void lsdc_disable_display(struct lsdc_device *ldev, unsigned int index)
+{
+	u32 val;
+
+	if (index == 0) {
+		val = readl(ldev->reg_base + LSDC_CRTC0_CFG_REG);
+		val &= ~CFG_OUTPUT_EN_BIT;
+		writel(val, ldev->reg_base + LSDC_CRTC0_CFG_REG);
+	} else if (index == 1) {
+		val = readl(ldev->reg_base + LSDC_CRTC1_CFG_REG);
+		val &= ~CFG_OUTPUT_EN_BIT;
+		writel(val, ldev->reg_base + LSDC_CRTC1_CFG_REG);
+	}
+}
+
+/*
+ * @lsdc_crtc_helper_atomic_enable:
+ *
+ * This callback should be used to enable the CRTC. With the atomic
+ * drivers it is called before all encoders connected to this CRTC are
+ * enabled through the encoder's own &drm_encoder_helper_funcs.enable
+ * hook.  If that sequence is too simple drivers can just add their own
+ * hooks and call it from this CRTC callback here by looping over all
+ * encoders connected to it using for_each_encoder_on_crtc().
+ *
+ * This hook is used only by atomic helpers, for symmetry with
+ * @atomic_disable. Atomic drivers don't need to implement it if there's
+ * no need to enable anything at the CRTC level. To ensure that runtime
+ * PM handling (using either DPMS or the new "ACTIVE" property) works
+ * @atomic_enable must be the inverse of @atomic_disable for atomic
+ * drivers.
+ *
+ * Drivers can use the @old_crtc_state input parameter if the operations
+ * needed to enable the CRTC don't depend solely on the new state but
+ * also on the transition between the old state and the new state.
+ *
+ * This function is optional.
+ */
+static void lsdc_crtc_helper_atomic_enable(struct drm_crtc *crtc,
+					   struct drm_crtc_state *old_crtc_state)
+{
+	struct drm_device *ddev = crtc->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+
+	drm_crtc_vblank_on(crtc);
+
+	lsdc_enable_display(ldev, drm_crtc_index(crtc));
+
+	drm_dbg(ddev, "%s: enabled\n", crtc->name);
+}
+
+static void lsdc_crtc_helper_atomic_disable(struct drm_crtc *crtc,
+					    struct drm_crtc_state *old_crtc_state)
+{
+	struct drm_device *ddev = crtc->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+
+	drm_crtc_vblank_off(crtc);
+
+	lsdc_disable_display(ldev, drm_crtc_index(crtc));
+
+	drm_dbg(ddev, "%s: disabled\n", crtc->name);
+}
+
+static void lsdc_crtc_update_clut(struct drm_crtc *crtc)
+{
+	struct lsdc_device *ldev = to_lsdc(crtc->dev);
+	unsigned int index = drm_crtc_index(crtc);
+	struct drm_color_lut *lut;
+	unsigned int i;
+
+	if (!ldev->enable_gamma)
+		return;
+
+	if (!crtc->state->color_mgmt_changed || !crtc->state->gamma_lut)
+		return;
+
+	lut = (struct drm_color_lut *)crtc->state->gamma_lut->data;
+
+	writel(0, ldev->reg_base + LSDC_CRTC0_GAMMA_INDEX_REG);
+
+	for (i = 0; i < 256; i++) {
+		u32 val = ((lut->red << 8) & 0xff0000) |
+			  (lut->green & 0xff00) |
+			  (lut->blue >> 8);
+
+		if (index == 0)
+			writel(val, ldev->reg_base + LSDC_CRTC0_GAMMA_DATA_REG);
+		else if (index == 1)
+			writel(val, ldev->reg_base + LSDC_CRTC1_GAMMA_DATA_REG);
+
+		lut++;
+	}
+}
+
+static void lsdc_crtc_atomic_flush(struct drm_crtc *crtc,
+				   struct drm_crtc_state *old_crtc_state)
+{
+	struct drm_pending_vblank_event *event = crtc->state->event;
+
+	lsdc_crtc_update_clut(crtc);
+
+	if (event) {
+		crtc->state->event = NULL;
+
+		spin_lock_irq(&crtc->dev->event_lock);
+		if (drm_crtc_vblank_get(crtc) == 0)
+			drm_crtc_arm_vblank_event(crtc, event);
+		else
+			drm_crtc_send_vblank_event(crtc, event);
+		spin_unlock_irq(&crtc->dev->event_lock);
+	}
+}
+
+static const struct drm_crtc_helper_funcs lsdc_crtc_helper_funcs = {
+	.mode_valid = lsdc_crtc_helper_mode_valid,
+	.mode_set_nofb = lsdc_crtc_helper_mode_set_nofb,
+	.atomic_enable = lsdc_crtc_helper_atomic_enable,
+	.atomic_disable = lsdc_crtc_helper_atomic_disable,
+	.atomic_check = lsdc_crtc_helper_atomic_check,
+	.atomic_flush = lsdc_crtc_atomic_flush,
+};
+
+int lsdc_crtc_init(struct drm_device *ddev,
+		   struct drm_crtc *crtc,
+		   unsigned int index,
+		   struct drm_plane *primary,
+		   struct drm_plane *cursor)
+{
+	int ret;
+
+	ret = drm_crtc_init_with_planes(ddev, crtc, primary, cursor,
+					&lsdc_crtc_funcs, "crtc-%d", index);
+
+	if (ret) {
+		drm_err(ddev, "crtc init with planes failed: %d\n", ret);
+		return ret;
+	}
+
+	drm_crtc_helper_add(crtc, &lsdc_crtc_helper_funcs);
+
+	ret = drm_mode_crtc_set_gamma_size(crtc, 256);
+	if (ret)
+		drm_warn(ddev, "set the gamma table size failed\n");
+
+	drm_crtc_enable_color_mgmt(crtc, 0, false, 256);
+
+	return 0;
+}

drivers/gpu/drm/loongson/lsdc_debugfs.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Loongson Corporation
+ */
+
+/*
+ * Authors:
+ *      Sui Jingfeng <suijingfeng@loongson.cn>
+ */
+
+#include <drm/drm_file.h>
+#include <drm/drm_device.h>
+#include <drm/drm_debugfs.h>
+#include <drm/drm_vma_manager.h>
+#include <drm/drm_gem_vram_helper.h>
+
+#include "lsdc_drv.h"
+#include "lsdc_pll.h"
+#include "lsdc_regs.h"
+#include "lsdc_debugfs.h"
+
+#ifdef CONFIG_DEBUG_FS
+
+static int lsdc_show_clock(struct seq_file *m, void *arg)
+{
+	struct drm_info_node *node = (struct drm_info_node *)m->private;
+	struct drm_device *ddev = node->minor->dev;
+	struct drm_crtc *crtc;
+
+	drm_for_each_crtc(crtc, ddev) {
+		struct lsdc_display_pipe *pipe;
+		struct lsdc_pll *pixpll;
+		const struct lsdc_pixpll_funcs *funcs;
+		struct lsdc_pll_core_values params;
+		unsigned int out_khz;
+		struct drm_display_mode *adj;
+
+		pipe = container_of(crtc, struct lsdc_display_pipe, crtc);
+		if (!pipe->available)
+			continue;
+
+		adj = &crtc->state->adjusted_mode;
+
+		pixpll = &pipe->pixpll;
+		funcs = pixpll->funcs;
+		out_khz = funcs->get_clock_rate(pixpll, &params);
+
+		seq_printf(m, "Display pipe %u: %dx%d\n",
+			   pipe->index, adj->hdisplay, adj->vdisplay);
+
+		seq_printf(m, "Frequency actually output: %u kHz\n", out_khz);
+		seq_printf(m, "Pixel clock required: %d kHz\n", adj->clock);
+		seq_printf(m, "diff: %d kHz\n", adj->clock);
+
+		seq_printf(m, "div_ref=%u, loopc=%u, div_out=%u\n",
+			   params.div_ref, params.loopc, params.div_out);
+
+		seq_printf(m, "hsync_start=%d, hsync_end=%d, htotal=%d\n",
+			   adj->hsync_start, adj->hsync_end, adj->htotal);
+		seq_printf(m, "vsync_start=%d, vsync_end=%d, vtotal=%d\n\n",
+			   adj->vsync_start, adj->vsync_end, adj->vtotal);
+	}
+
+	return 0;
+}
+
+static int lsdc_show_mm(struct seq_file *m, void *arg)
+{
+	struct drm_info_node *node = (struct drm_info_node *)m->private;
+	struct drm_device *ddev = node->minor->dev;
+	struct drm_printer p = drm_seq_file_printer(m);
+
+	drm_mm_print(&ddev->vma_offset_manager->vm_addr_space_mm, &p);
+
+	return 0;
+}
+
+#define REGDEF(reg) { __stringify_1(LSDC_##reg##_REG), LSDC_##reg##_REG }
+static const struct {
+	const char *name;
+	u32 reg_offset;
+} lsdc_regs_array[] = {
+	REGDEF(INT),
+	REGDEF(CRTC0_CFG),
+	REGDEF(CRTC0_FB_ADDR0),
+	REGDEF(CRTC0_FB_ADDR1),
+	REGDEF(CRTC0_FB_HI_ADDR),
+	REGDEF(CRTC0_STRIDE),
+	REGDEF(CRTC0_FB_ORIGIN),
+	REGDEF(CRTC0_HDISPLAY),
+	REGDEF(CRTC0_HSYNC),
+	REGDEF(CRTC0_VDISPLAY),
+	REGDEF(CRTC0_VSYNC),
+	REGDEF(CRTC0_GAMMA_INDEX),
+	REGDEF(CRTC0_GAMMA_DATA),
+	REGDEF(CRTC1_CFG),
+	REGDEF(CRTC1_FB_ADDR0),
+	REGDEF(CRTC1_FB_ADDR1),
+	REGDEF(CRTC1_FB_HI_ADDR),
+	REGDEF(CRTC1_STRIDE),
+	REGDEF(CRTC1_FB_ORIGIN),
+	REGDEF(CRTC1_HDISPLAY),
+	REGDEF(CRTC1_HSYNC),
+	REGDEF(CRTC1_VDISPLAY),
+	REGDEF(CRTC1_VSYNC),
+	REGDEF(CRTC1_GAMMA_INDEX),
+	REGDEF(CRTC1_GAMMA_DATA),
+	REGDEF(CURSOR0_CFG),
+	REGDEF(CURSOR0_ADDR),
+	REGDEF(CURSOR0_POSITION),
+	REGDEF(CURSOR0_BG_COLOR),
+	REGDEF(CURSOR0_FG_COLOR),
+};
+
+static int lsdc_show_regs(struct seq_file *m, void *arg)
+{
+	struct drm_info_node *node = (struct drm_info_node *)m->private;
+	struct drm_device *ddev = node->minor->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(lsdc_regs_array); i++) {
+		u32 offset = lsdc_regs_array[i].reg_offset;
+		const char *name = lsdc_regs_array[i].name;
+
+		seq_printf(m, "%s (0x%04x): 0x%08x\n",
+			   name, offset,
+			   readl(ldev->reg_base + offset));
+	}
+
+	return 0;
+}
+
+static const struct drm_info_list lsdc_debugfs_list[] = {
+	{ "clocks", lsdc_show_clock, 0 },
+	{ "mm",     lsdc_show_mm,   0, NULL },
+	{ "regs",   lsdc_show_regs, 0 },
+};
+
+void lsdc_debugfs_init(struct drm_minor *minor)
+{
+	drm_debugfs_create_files(lsdc_debugfs_list,
+				 ARRAY_SIZE(lsdc_debugfs_list),
+				 minor->debugfs_root,
+				 minor);
+}
+
+/*
+ * vram debugfs related.
+ */
+static int lsdc_vram_mm_show(struct seq_file *m, void *data)
+{
+	struct drm_info_node *node = (struct drm_info_node *)m->private;
+	struct drm_vram_mm *vmm = node->minor->dev->vram_mm;
+	struct ttm_resource_manager *man = ttm_manager_type(&vmm->bdev, TTM_PL_VRAM);
+	struct drm_printer p = drm_seq_file_printer(m);
+
+	ttm_resource_manager_debug(man, &p);
+	return 0;
+}
+
+static const struct drm_info_list lsdc_vram_mm_debugfs_list[] = {
+	{ "clocks", lsdc_show_clock, 0 },
+	{ "vram-mm", lsdc_vram_mm_show, 0, NULL },
+	{ "regs",   lsdc_show_regs, 0 },
+};
+
+void lsdc_vram_mm_debugfs_init(struct drm_minor *minor)
+{
+	drm_debugfs_create_files(lsdc_vram_mm_debugfs_list,
+				 ARRAY_SIZE(lsdc_vram_mm_debugfs_list),
+				 minor->debugfs_root,
+				 minor);
+}
+
+#endif

drivers/gpu/drm/loongson/lsdc_debugfs.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2022 Loongson Corporation
+ */
+
+/*
+ * Authors:
+ *      Sui Jingfeng <suijingfeng@loongson.cn>
+ */
+
+#ifndef __LSDC_DEBUGFS_H__
+#define __LSDC_DEBUGFS_H__
+
+void lsdc_debugfs_init(struct drm_minor *minor);
+void lsdc_vram_mm_debugfs_init(struct drm_minor *minor);
+
+#endif

drivers/gpu/drm/loongson/lsdc_drv.c

+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2022 Loongson Corporation
+ */
+
+/*
+ * Authors:
+ *      Sui Jingfeng <suijingfeng@loongson.cn>
+ */
+
+#include <linux/pci.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/platform_device.h>
+
+#include <drm/drm_vblank.h>
+#include <drm/drm_fb_helper.h>
+#include <drm/drm_gem_cma_helper.h>
+#include <drm/drm_fb_cma_helper.h>
+#include <drm/drm_gem_vram_helper.h>
+#include <drm/drm_gem_framebuffer_helper.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_probe_helper.h>
+
+#include "lsdc_drv.h"
+#include "lsdc_irq.h"
+#include "lsdc_output.h"
+#include "lsdc_debugfs.h"
+
+static const struct lsdc_chip_desc dc_in_ls2k1000 = {
+	.chip = LSDC_CHIP_2K1000,
+	.num_of_crtc = LSDC_NUM_CRTC,
+	/* ls2k1000 user manual say the max pixel clock can be about 200MHz */
+	.max_pixel_clk = 200000,
+	.max_width = 2560,
+	.max_height = 2048,
+	.num_of_hw_cursor = 1,
+	.hw_cursor_w = 32,
+	.hw_cursor_h = 32,
+	.stride_alignment = 256,
+	.has_builtin_i2c = false,
+	.has_vram = false,
+	.broken_gamma = true,
+};
+
+static const struct lsdc_chip_desc dc_in_ls2k0500 = {
+	.chip = LSDC_CHIP_2K0500,
+	.num_of_crtc = LSDC_NUM_CRTC,
+	.max_pixel_clk = 200000,
+	.max_width = 2048,
+	.max_height = 2048,
+	.num_of_hw_cursor = 1,
+	.hw_cursor_w = 32,
+	.hw_cursor_h = 32,
+	.stride_alignment = 256,
+	.has_builtin_i2c = false,
+	.has_vram = false,
+	.broken_gamma = true,
+};
+
+static const struct lsdc_chip_desc dc_in_ls7a1000 = {
+	.chip = LSDC_CHIP_7A1000,
+	.num_of_crtc = LSDC_NUM_CRTC,
+	.max_pixel_clk = 200000,
+	.max_width = 2048,
+	.max_height = 2048,
+	.num_of_hw_cursor = 1,
+	.hw_cursor_w = 32,
+	.hw_cursor_h = 32,
+	.stride_alignment = 256,
+	.has_builtin_i2c = true,
+	.has_vram = true,
+	.broken_gamma = true,
+};
+
+static const struct lsdc_chip_desc dc_in_ls7a2000 = {
+	.chip = LSDC_CHIP_7A2000,
+	.num_of_crtc = LSDC_NUM_CRTC,
+	.max_pixel_clk = 200000,
+	.max_width = 2048,
+	.max_height = 2048,
+	.num_of_hw_cursor = 2,
+	.hw_cursor_w = 64,
+	.hw_cursor_h = 64,
+	.stride_alignment = 256,
+	.has_builtin_i2c = true,
+	.has_vram = true,
+	.broken_gamma = true,
+};
+
+static enum drm_mode_status
+lsdc_device_mode_valid(struct drm_device *ddev, const struct drm_display_mode *mode)
+{
+	struct lsdc_device *ldev = to_lsdc(ddev);
+
+	if (ldev->use_vram_helper)
+		return drm_vram_helper_mode_valid(ddev, mode);
+
+	return MODE_OK;
+}
+
+static const struct drm_mode_config_funcs lsdc_mode_config_funcs = {
+	.fb_create = drm_gem_fb_create,
+	.output_poll_changed = drm_fb_helper_output_poll_changed,
+	.atomic_check = drm_atomic_helper_check,
+	.atomic_commit = drm_atomic_helper_commit,
+	.mode_valid = lsdc_device_mode_valid,
+};
+
+static int lsdc_gem_cma_dumb_create(struct drm_file *file,
+				    struct drm_device *ddev,
+				    struct drm_mode_create_dumb *args)
+{
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	const struct lsdc_chip_desc *desc = ldev->desc;
+	unsigned int bytes_per_pixel = (args->bpp + 7) / 8;
+	unsigned int pitch = bytes_per_pixel * args->width;
+
+	/*
+	 * The dc in ls7a1000/ls2k1000/ls2k0500 require the stride be a
+	 * multiple of 256 bytes which is for sake of optimize dma data
+	 * transfer.
+	 */
+	args->pitch = roundup(pitch, desc->stride_alignment);
+
+	return drm_gem_cma_dumb_create_internal(file, ddev, args);
+}
+
+DEFINE_DRM_GEM_CMA_FOPS(lsdc_drv_fops);
+
+static struct drm_driver lsdc_drm_driver_cma_stub = {
+	.driver_features = DRIVER_GEM | DRIVER_MODESET | DRIVER_ATOMIC,
+	.lastclose = drm_fb_helper_lastclose,
+	.fops = &lsdc_drv_fops,
+
+	.name = "lsdc",
+	.desc = DRIVER_DESC,
+	.date = DRIVER_DATE,
+	.major = DRIVER_MAJOR,
+	.minor = DRIVER_MINOR,
+	.patchlevel = DRIVER_PATCHLEVEL,
+
+	DRM_GEM_CMA_DRIVER_OPS_WITH_DUMB_CREATE(lsdc_gem_cma_dumb_create),
+
+#ifdef CONFIG_DEBUG_FS
+	.debugfs_init = lsdc_debugfs_init,
+#endif
+};
+
+DEFINE_DRM_GEM_FOPS(lsdc_gem_fops);
+
+static struct drm_driver lsdc_vram_driver_stub = {
+	.driver_features = DRIVER_MODESET | DRIVER_GEM | DRIVER_ATOMIC,
+	.fops = &lsdc_gem_fops,
+
+	.name = "loongson-drm",
+	.desc = DRIVER_DESC,
+	.date = DRIVER_DATE,
+	.major = DRIVER_MAJOR,
+	.minor = DRIVER_MINOR,
+	.patchlevel = DRIVER_PATCHLEVEL,
+#ifdef CONFIG_DEBUG_FS
+	.debugfs_init = lsdc_vram_mm_debugfs_init,
+#endif
+	.dumb_create = drm_gem_vram_driver_dumb_create,
+	.dumb_map_offset = drm_gem_vram_driver_dumb_mmap_offset,
+	.gem_prime_mmap = drm_gem_prime_mmap,
+};
+
+static int lsdc_modeset_init(struct lsdc_device *ldev, uint32_t num_crtc)
+{
+	struct drm_device *ddev = ldev->ddev;
+	unsigned int i;
+	int ret;
+
+	if (ldev->has_ports_node) {
+		drm_info(ddev, "Has OF graph support\n");
+		ret = lsdc_attach_output(ldev, num_crtc);
+		if (ret)
+			return ret;
+	} else {
+		drm_info(ddev, "No OF graph support\n");
+		for (i = 0; i < num_crtc; i++) {
+			ret = lsdc_create_output(ldev, i, num_crtc);
+			if (ret)
+				return ret;
+		}
+	}
+
+	for (i = 0; i < num_crtc; i++) {
+		struct lsdc_display_pipe * const dispipe = &ldev->dispipe[i];
+		struct drm_plane * const primary = &dispipe->primary;
+		struct drm_plane * const cursor = &dispipe->cursor;
+		struct drm_crtc * const crtc = &dispipe->crtc;
+		struct lsdc_pll * const pixpll = &dispipe->pixpll;
+
+		dispipe->index = i;
+
+		ret = lsdc_pixpll_init(pixpll, ddev, i);
+		if (ret)
+			return ret;
+
+		ret = lsdc_plane_init(ldev, primary, DRM_PLANE_TYPE_PRIMARY, i);
+		if (ret)
+			return ret;
+
+		ret = lsdc_plane_init(ldev, cursor, DRM_PLANE_TYPE_CURSOR, i);
+		if (ret)
+			return ret;
+
+		/*
+		 * Initial all of the CRTC available, in this way the crtc
+		 * index is equal to the hardware crtc index. That is:
+		 * display pipe 0 => crtc0 + dvo0 + encoder0
+		 * display pipe 1 => crtc1 + dvo1 + encoder1
+		 */
+		ret = lsdc_crtc_init(ddev, crtc, i, primary, cursor);
+		if (ret)
+			return ret;
+
+		drm_info(ddev, "display pipe %u initialized\n", i);
+	}
+
+	return 0;
+}
+
+static int lsdc_mode_config_init(struct lsdc_device *ldev)
+{
+	const struct lsdc_chip_desc * const descp = ldev->desc;
+	struct drm_device *ddev = ldev->ddev;
+	int ret;
+
+	ret = drmm_mode_config_init(ddev);
+	if (ret)
+		return ret;
+
+	ddev->mode_config.funcs = &lsdc_mode_config_funcs;
+	ddev->mode_config.min_width = 1;
+	ddev->mode_config.min_height = 1;
+	ddev->mode_config.max_width = 4096;
+	ddev->mode_config.max_height = 4096;
+	ddev->mode_config.preferred_depth = 24;
+	ddev->mode_config.prefer_shadow = ldev->use_vram_helper;
+
+	ddev->mode_config.cursor_width = descp->hw_cursor_h;
+	ddev->mode_config.cursor_height = descp->hw_cursor_h;
+
+	if (ldev->vram_base)
+		ddev->mode_config.fb_base = ldev->vram_base;
+
+	return lsdc_modeset_init(ldev, descp->num_of_crtc);
+}
+
+static void lsdc_mode_config_fini(struct drm_device *ddev)
+{
+	drm_atomic_helper_shutdown(ddev);
+
+	drm_mode_config_cleanup(ddev);
+}
+
+/*
+ * lsdc_detect_chip - a function to tell different chips apart.
+ */
+const struct lsdc_chip_desc *
+lsdc_detect_chip(struct pci_dev *pdev, const struct pci_device_id * const ent)
+{
+	static const struct lsdc_match {
+		char name[128];
+		const void *data;
+	} compat[] = {
+		{ .name = "loongson,ls7a1000-dc", .data = &dc_in_ls7a1000 },
+		{ .name = "loongson,ls2k1000-dc", .data = &dc_in_ls2k1000 },
+		{ .name = "loongson,ls2k0500-dc", .data = &dc_in_ls2k0500 },
+		{ .name = "loongson,ls7a2000-dc", .data = &dc_in_ls7a2000 },
+		{ .name = "loongson,loongson64c-4core-ls7a", .data = &dc_in_ls7a1000 },
+		{ .name = "loongson,loongson64g-4core-ls7a", .data = &dc_in_ls7a1000 },
+		{ .name = "loongson,loongson64-2core-2k1000", .data = &dc_in_ls2k1000 },
+		{ .name = "loongson,loongson2k1000", .data = &dc_in_ls2k1000 },
+		{ /* sentinel */ },
+	};
+
+	struct device_node *np;
+	unsigned int i;
+
+	if (ent->driver_data == LSDC_CHIP_7A2000)
+		return &dc_in_ls7a2000;
+
+	if (ent->driver_data == LSDC_CHIP_7A1000)
+		return &dc_in_ls7a1000;
+
+	/* Deduce DC variant information from the DC device node */
+	for (i = 0; i < ARRAY_SIZE(compat); ++i) {
+		np = of_find_compatible_node(NULL, NULL, compat[i].name);
+		if (!np)
+			continue;
+
+		of_node_put(np);
+
+		return compat[i].data;
+	}
+
+	dev_info(&pdev->dev, "No Compatible Device Node Found\n");
+
+	if (pci_get_device(PCI_VENDOR_ID_LOONGSON, 0x7A15, NULL))
+		return &dc_in_ls7a1000;
+	else if (pci_get_device(PCI_VENDOR_ID_LOONGSON, 0x7A05, NULL))
+		return &dc_in_ls2k1000;
+
+	return NULL;
+}
+
+static int lsdc_remove_conflicting_framebuffers(const struct drm_driver *drv)
+{
+	struct apertures_struct *ap;
+
+	ap = alloc_apertures(1);
+	if (!ap)
+		return -ENOMEM;
+
+	/* lsdc is a pci device, but it don't have a dedicate vram bar because
+	 * of historic reason. The display controller is ported from Loongson
+	 * 2H series SoC which date back to 2012.
+	 * And simplefb node may have been located anywhere in memory.
+	 */
+
+	ap->ranges[0].base = 0;
+	ap->ranges[0].size = ~0;
+
+	return drm_fb_helper_remove_conflicting_framebuffers(ap, "loongsondrmfb", false);
+}
+
+static int lsdc_platform_probe(struct platform_device *pdev)
+{
+	struct lsdc_device *ldev = dev_get_drvdata(pdev->dev.parent);
+	struct drm_driver *driver;
+	struct drm_device *ddev;
+	int ret;
+
+	if (ldev->use_vram_helper)
+		driver = &lsdc_vram_driver_stub;
+	else
+		driver = &lsdc_drm_driver_cma_stub;
+
+	lsdc_remove_conflicting_framebuffers(driver);
+
+	ddev = drm_dev_alloc(driver, &pdev->dev);
+	if (IS_ERR(ddev))
+		return PTR_ERR(ddev);
+
+	platform_set_drvdata(pdev, ddev);
+	ldev->ddev = ddev;
+	ddev->dev_private = ldev;
+
+	if (ldev->use_vram_helper) {
+		ret = drmm_vram_helper_init(ddev, ldev->vram_base, ldev->vram_size);
+		if (ret) {
+			drm_err(ddev, "vram helper init failed: %d\n", ret);
+			goto err_kms;
+		}
+	};
+
+	ret = lsdc_mode_config_init(ldev);
+	if (ret) {
+		drm_dbg(ddev, "%s: %d\n", __func__, ret);
+		goto err_kms;
+	}
+
+	ret = devm_request_threaded_irq(&pdev->dev, ldev->irq,
+					lsdc_irq_handler_cb,
+					lsdc_irq_thread_cb,
+					IRQF_ONESHOT, NULL,
+					ddev);
+	if (ret) {
+		drm_err(ddev, "Failed to register lsdc interrupt\n");
+		goto err_kms;
+	}
+
+	ret = drm_vblank_init(ddev, ldev->desc->num_of_crtc);
+	if (ret)
+		goto err_kms;
+
+	drm_mode_config_reset(ddev);
+
+	drm_kms_helper_poll_init(ddev);
+
+	ret = drm_dev_register(ddev, 0);
+	if (ret)
+		goto err_poll_fini;
+
+	drm_fbdev_generic_setup(ddev, 32);
+
+	return 0;
+
+err_poll_fini:
+	drm_kms_helper_poll_fini(ddev);
+err_kms:
+	drm_dev_put(ddev);
+
+	return ret;
+}
+
+static int lsdc_platform_remove(struct platform_device *pdev)
+{
+	struct drm_device *ddev = platform_get_drvdata(pdev);
+	struct lsdc_device *ldev = to_lsdc(ddev);
+
+	drm_dev_unregister(ddev);
+
+	drm_kms_helper_poll_fini(ddev);
+
+	devm_free_irq(ddev->dev, ldev->irq, ddev);
+
+	lsdc_mode_config_fini(ddev);
+
+	platform_set_drvdata(pdev, NULL);
+
+	drm_dev_put(ddev);
+
+	return 0;
+}
+
+struct platform_driver lsdc_platform_driver = {
+	.probe = lsdc_platform_probe,
+	.remove = lsdc_platform_remove,
+	.driver = {
+		.name = "lsdc",
+	},
+};

drivers/gpu/drm/loongson/lsdc_drv.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2022 Loongson Corporation
+ */
+
+/*
+ * Authors:
+ *      Sui Jingfeng <suijingfeng@loongson.cn>
+ */
+
+#ifndef __LSDC_DRV_H__
+#define __LSDC_DRV_H__
+
+#include <drm/drm_print.h>
+#include <drm/drm_device.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_plane.h>
+#include <drm/drm_connector.h>
+#include <drm/drm_encoder.h>
+#include <drm/drm_drv.h>
+#include <drm/drm_atomic.h>
+
+#include "lsdc_pll.h"
+
+#define DRIVER_AUTHOR		"Sui Jingfeng <suijingfeng@loongson.cn>"
+#define DRIVER_NAME		"lsdc"
+#define DRIVER_DESC		"drm driver for loongson's display controller"
+#define DRIVER_DATE		"20200701"
+#define DRIVER_MAJOR		1
+#define DRIVER_MINOR		0
+#define DRIVER_PATCHLEVEL	0
+
+#define LSDC_NUM_CRTC           2
+
+enum loongson_dc_family {
+	LSDC_CHIP_UNKNOWN = 0,
+	LSDC_CHIP_2K1000 = 1,  /* 2-Core Mips64r2 compatible SoC */
+	LSDC_CHIP_7A1000 = 2,  /* North bridge of LS3A3000/LS3A4000/LS3A5000 */
+	LSDC_CHIP_2K0500 = 3,  /* Single core, reduced version of LS2K1000 */
+	LSDC_CHIP_7A2000 = 4,  /* Enhancement version of LS7a1000 */
+	LSDC_CHIP_LAST,
+};
+
+struct lsdc_chip_desc {
+	enum loongson_dc_family chip;
+	u32 num_of_crtc;
+	u32 max_pixel_clk;
+	u32 max_width;
+	u32 max_height;
+	u32 num_of_hw_cursor;
+	u32 hw_cursor_w;
+	u32 hw_cursor_h;
+	/* DMA alignment constraint (must be multiple of 256 bytes) */
+	u32 stride_alignment;
+	bool has_builtin_i2c;
+	bool has_vram;
+	bool broken_gamma;
+};
+
+/* There is only a 1:1 mapping of encoders and connectors for lsdc */
+struct lsdc_output {
+	struct drm_encoder encoder;
+	struct drm_connector connector;
+	struct lsdc_i2c *li2c;
+};
+
+static inline struct lsdc_output *
+drm_connector_to_lsdc_output(struct drm_connector *connp)
+{
+	return container_of(connp, struct lsdc_output, connector);
+}
+
+/*
+ * struct lsdc_display_pipe - Abstraction of hardware display pipeline.
+ * @crtc: CRTC control structure
+ * @plane: Plane control structure
+ * @encoder: Encoder control structure
+ * @pixpll: Pll control structure
+ * @connector: point to connector control structure this display pipe bind
+ * @index: the index corresponding to the hardware display pipe
+ * @available: is this display pipe is available on the motherboard, The
+ *  downstream mother board manufacturer may use only one of them.
+ *  For example, LEMOTE LX-6901 board just has only one VGA output.
+ *
+ * Display pipeline with planes, crtc, pll and output collapsed into one entity.
+ */
+struct lsdc_display_pipe {
+	struct drm_crtc crtc;
+	struct drm_plane primary;
+	struct drm_plane cursor;
+	struct lsdc_pll pixpll;
+	struct lsdc_output *output;
+	int index;
+	bool available;
+};
+
+static inline struct lsdc_display_pipe *
+drm_crtc_to_dispipe(struct drm_crtc *crtc)
+{
+	return container_of(crtc, struct lsdc_display_pipe, crtc);
+}
+
+static inline struct lsdc_display_pipe *
+lsdc_cursor_to_dispipe(struct drm_plane *plane)
+{
+	return container_of(plane, struct lsdc_display_pipe, cursor);
+}
+
+struct lsdc_crtc_state {
+	struct drm_crtc_state base;
+	struct lsdc_pll_core_values pparams;
+};
+
+struct lsdc_device {
+	struct device *dev;
+	struct drm_device *ddev;
+	/* @dc: pointer to the platform device created at runtime */
+	struct platform_device *dc;
+	/* @desc: device dependent data and feature descriptions */
+	const struct lsdc_chip_desc *desc;
+
+	/* LS7A1000/LS7A2000 has a dediacted video RAM */
+	void __iomem *reg_base;
+	void __iomem *vram;
+	resource_size_t vram_base;
+	resource_size_t vram_size;
+
+	struct lsdc_display_pipe dispipe[LSDC_NUM_CRTC];
+
+	/*
+	 * @num_output: count the number of active display pipe.
+	 */
+	unsigned int num_output;
+
+	int irq;
+	u32 irq_status;
+
+	/*
+	 * @use_vram_helper: using vram helper base solution instead of
+	 * CMA helper based solution. The DC scanout from the VRAM is
+	 * proved to be more reliable, but graphic application is may
+	 * become slow when using this driver mode.
+	 */
+	bool use_vram_helper;
+	/*
+	 * @enable_gamma: control whether hardware gamma support should be
+	 * enabled or not. It is broken though, but you can know that only
+	 * when you can enable it.
+	 */
+	bool enable_gamma;
+	/* @relax_alignment: for 800x480, 1366x768 resulotion support */
+	bool relax_alignment;
+	/* @has_dt: true if there are DT support*/
+	bool has_dt;
+	/* @has_ports_node: true if there are OF graph in the DT */
+	bool has_ports_node;
+};
+
+static inline struct lsdc_device *to_lsdc(struct drm_device *ddev)
+{
+	return ddev->dev_private;
+}
+
+static inline struct lsdc_crtc_state *
+to_lsdc_crtc_state(struct drm_crtc_state *base)
+{
+	return container_of(base, struct lsdc_crtc_state, base);
+}
+
+int lsdc_crtc_init(struct drm_device *ddev,
+		   struct drm_crtc *crtc,
+		   unsigned int index,
+		   struct drm_plane *primary,
+		   struct drm_plane *cursor);
+
+int lsdc_plane_init(struct lsdc_device *ldev, struct drm_plane *plane,
+		    enum drm_plane_type type, unsigned int index);
+
+const struct lsdc_chip_desc *
+lsdc_detect_chip(struct pci_dev *pdev, const struct pci_device_id * const ent);
+
+extern struct platform_driver lsdc_platform_driver;
+
+#endif

drivers/gpu/drm/loongson/lsdc_i2c.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Loongson Corporation
+ */
+
+/*
+ * Authors:
+ *      Sui Jingfeng <suijingfeng@loongson.cn>
+ */
+
+#include <linux/i2c.h>
+
+#include <drm/drm_print.h>
+#include <drm/drm_device.h>
+#include <drm/drm_managed.h>
+
+#include "lsdc_regs.h"
+#include "lsdc_i2c.h"
+
+/*
+ * ls7a_gpio_i2c_set - set the state of a gpio pin, either high or low.
+ * @mask: gpio pin mask indicate which pin to set
+ */
+static void ls7a_gpio_i2c_set(struct lsdc_i2c * const li2c, int mask, int state)
+{
+	unsigned long flags;
+	u8 val;
+
+	spin_lock_irqsave(&li2c->reglock, flags);
+
+	if (state) {
+		/*
+		 * The high state is achieved by setting the direction as
+		 * input, because the GPIO is open drained with external
+		 * pull up resistance.
+		 */
+		val = readb(li2c->dir_reg);
+		val |= mask;
+		writeb(val, li2c->dir_reg);
+	} else {
+		/* First, set this pin as output */
+		val = readb(li2c->dir_reg);
+		val &= ~mask;
+		writeb(val, li2c->dir_reg);
+
+		/* Then, set the state to it */
+		val = readb(li2c->dat_reg);
+		val &= ~mask;
+		writeb(val, li2c->dat_reg);
+	}
+
+	spin_unlock_irqrestore(&li2c->reglock, flags);
+}
+
+/*
+ * ls7a_gpio_i2c_get - read value back from gpio pin
+ * @mask: gpio pin mask indicate which pin to read from
+ */
+static int ls7a_gpio_i2c_get(struct lsdc_i2c * const li2c, int mask)
+{
+	unsigned long flags;
+	u8 val;
+
+	spin_lock_irqsave(&li2c->reglock, flags);
+
+	/* First, set this pin as input */
+	val = readb(li2c->dir_reg);
+	val |= mask;
+	writeb(val, li2c->dir_reg);
+
+	/* Then, get level state from this pin */
+	val = readb(li2c->dat_reg);
+
+	spin_unlock_irqrestore(&li2c->reglock, flags);
+
+	return (val & mask) ? 1 : 0;
+}
+
+/* set the state on the i2c->sda pin */
+static void ls7a_i2c_set_sda(void *i2c, int state)
+{
+	struct lsdc_i2c * const li2c = (struct lsdc_i2c *)i2c;
+
+	return ls7a_gpio_i2c_set(li2c, li2c->sda, state);
+}
+
+/* set the state on the i2c->scl pin */
+static void ls7a_i2c_set_scl(void *i2c, int state)
+{
+	struct lsdc_i2c * const li2c = (struct lsdc_i2c *)i2c;
+
+	return ls7a_gpio_i2c_set(li2c, li2c->scl, state);
+}
+
+/* read the value from the i2c->sda pin */
+static int ls7a_i2c_get_sda(void *i2c)
+{
+	struct lsdc_i2c * const li2c = (struct lsdc_i2c *)i2c;
+
+	return ls7a_gpio_i2c_get(li2c, li2c->sda);
+}
+
+/* read the value from the i2c->scl pin */
+static int ls7a_i2c_get_scl(void *i2c)
+{
+	struct lsdc_i2c * const li2c = (struct lsdc_i2c *)i2c;
+
+	return ls7a_gpio_i2c_get(li2c, li2c->scl);
+}
+
+/*
+ * Mainly for dc in ls7a1000 which have dedicated gpio hardware
+ */
+static void lsdc_of_release_i2c_adapter(void *res)
+{
+	struct lsdc_i2c *li2c = res;
+	struct i2c_adapter *adapter;
+	struct device_node *i2c_np;
+
+	adapter = &li2c->adapter;
+	i2c_np = adapter->dev.of_node;
+	if (i2c_np)
+		of_node_put(i2c_np);
+
+	i2c_del_adapter(adapter);
+
+	kfree(li2c);
+}
+
+struct lsdc_i2c *lsdc_of_create_i2c_adapter(struct device *parent,
+					    void *reg_base,
+					    struct device_node *i2c_np)
+{
+	unsigned int udelay = 5;
+	unsigned int timeout = 2200;
+	int nr = -1;
+	struct i2c_adapter *adapter;
+	struct lsdc_i2c *li2c;
+	u32 sda, scl;
+	int ret;
+
+	li2c = kzalloc(sizeof(*li2c), GFP_KERNEL);
+	if (!li2c)
+		return ERR_PTR(-ENOMEM);
+
+	spin_lock_init(&li2c->reglock);
+
+	ret = of_property_read_u32(i2c_np, "loongson,sda", &sda);
+	if (ret) {
+		dev_err(parent, "No sda pin number provided\n");
+		return ERR_PTR(ret);
+	}
+
+	ret = of_property_read_u32(i2c_np, "loongson,scl", &scl);
+	if (ret) {
+		dev_err(parent, "No scl pin number provided\n");
+		return ERR_PTR(ret);
+	}
+
+	ret = of_property_read_u32(i2c_np, "loongson,nr", &nr);
+	if (ret) {
+		int id;
+
+		if (ret == -EINVAL)
+			dev_dbg(parent, "no nr provided\n");
+
+		id = of_alias_get_id(i2c_np, "i2c");
+		if (id >= 0)
+			nr = id;
+	}
+
+	li2c->sda = 1 << sda;
+	li2c->scl = 1 << scl;
+
+	/* Optional properties which made the driver more flexible */
+	of_property_read_u32(i2c_np, "loongson,udelay", &udelay);
+	of_property_read_u32(i2c_np, "loongson,timeout", &timeout);
+
+	li2c->dir_reg = reg_base + LS7A_DC_GPIO_DIR_REG;
+	li2c->dat_reg = reg_base + LS7A_DC_GPIO_DAT_REG;
+
+	li2c->bit.setsda = ls7a_i2c_set_sda;
+	li2c->bit.setscl = ls7a_i2c_set_scl;
+	li2c->bit.getsda = ls7a_i2c_get_sda;
+	li2c->bit.getscl = ls7a_i2c_get_scl;
+	li2c->bit.udelay = udelay;
+	li2c->bit.timeout = usecs_to_jiffies(timeout);
+	li2c->bit.data = li2c;
+
+	adapter = &li2c->adapter;
+	adapter->algo_data = &li2c->bit;
+	adapter->owner = THIS_MODULE;
+	adapter->class = I2C_CLASS_DDC;
+	adapter->dev.parent = parent;
+	adapter->nr = nr;
+	adapter->dev.of_node = i2c_np;
+
+	snprintf(adapter->name, sizeof(adapter->name), "gpio-i2c-%d", nr);
+
+	i2c_set_adapdata(adapter, li2c);
+
+	ret = i2c_bit_add_numbered_bus(adapter);
+	if (ret) {
+		if (i2c_np)
+			of_node_put(i2c_np);
+
+		kfree(li2c);
+		return ERR_PTR(ret);
+	}
+
+	dev_info(parent, "sda=%u, scl=%u, nr=%d, udelay=%u, timeout=%u\n",
+		 li2c->sda, li2c->scl, nr, udelay, timeout);
+
+	ret = devm_add_action_or_reset(parent, lsdc_of_release_i2c_adapter, li2c);
+	if (ret)
+		return NULL;
+
+	return li2c;
+}
+
+static void lsdc_release_i2c_chan(struct drm_device *dev, void *res)
+{
+	struct lsdc_i2c *li2c = res;
+
+	i2c_del_adapter(&li2c->adapter);
+
+	kfree(li2c);
+}
+
+struct lsdc_i2c *lsdc_create_i2c_chan(struct drm_device *ddev,
+				      void *reg_base,
+				      unsigned int index)
+{
+	struct i2c_adapter *adapter;
+	struct lsdc_i2c *li2c;
+	int ret;
+
+	li2c = kzalloc(sizeof(*li2c), GFP_KERNEL);
+	if (!li2c)
+		return ERR_PTR(-ENOMEM);
+
+	if (index == 0) {
+		li2c->sda = 0x01;
+		li2c->scl = 0x02;
+	} else if (index == 1) {
+		li2c->sda = 0x04;
+		li2c->scl = 0x08;
+	}
+
+	spin_lock_init(&li2c->reglock);
+
+	li2c->dir_reg = reg_base + LS7A_DC_GPIO_DIR_REG;
+	li2c->dat_reg = reg_base + LS7A_DC_GPIO_DAT_REG;
+
+	li2c->bit.setsda = ls7a_i2c_set_sda;
+	li2c->bit.setscl = ls7a_i2c_set_scl;
+	li2c->bit.getsda = ls7a_i2c_get_sda;
+	li2c->bit.getscl = ls7a_i2c_get_scl;
+	li2c->bit.udelay = 5;
+	li2c->bit.timeout = usecs_to_jiffies(2200);
+	li2c->bit.data = li2c;
+
+	adapter = &li2c->adapter;
+	adapter->algo_data = &li2c->bit;
+	adapter->owner = THIS_MODULE;
+	adapter->class = I2C_CLASS_DDC;
+	adapter->dev.parent = ddev->dev;
+	adapter->nr = -1;
+
+	snprintf(adapter->name, sizeof(adapter->name), "gpio-i2c-%d", index);
+
+	i2c_set_adapdata(adapter, li2c);
+
+	ret = i2c_bit_add_bus(adapter);
+	if (ret) {
+		kfree(li2c);
+		return ERR_PTR(ret);
+	}
+
+	ret = drmm_add_action_or_reset(ddev, lsdc_release_i2c_chan, li2c);
+	if (ret)
+		return NULL;
+
+	drm_info(ddev, "%s: sda=%u, scl=%u\n",
+		 adapter->name, li2c->sda, li2c->scl);
+
+	return li2c;
+}

drivers/gpu/drm/loongson/lsdc_i2c.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2022 Loongson Corporation
+ */
+
+/*
+ * Authors:
+ *      Sui Jingfeng <suijingfeng@loongson.cn>
+ */
+
+#ifndef __LSDC_I2C__
+#define __LSDC_I2C__
+
+#include <linux/i2c.h>
+#include <linux/i2c-algo-bit.h>
+#include <linux/of.h>
+
+struct lsdc_i2c {
+	struct i2c_adapter adapter;
+	struct i2c_algo_bit_data bit;
+	/* @reglock: protects concurrent register access */
+	spinlock_t reglock;
+	void __iomem *dir_reg;
+	void __iomem *dat_reg;
+	/* pin bit mask */
+	u8 sda;
+	u8 scl;
+};
+
+struct lsdc_i2c *lsdc_create_i2c_chan(struct drm_device *ddev,
+				      void *reg_base,
+				      unsigned int index);
+
+struct lsdc_i2c *lsdc_of_create_i2c_adapter(struct device *dev,
+					    void *reg_base,
+					    struct device_node *i2c_np);
+
+#endif

drivers/gpu/drm/loongson/lsdc_irq.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Loongson Corporation
+ */
+
+/*
+ * Authors:
+ *      Sui Jingfeng <suijingfeng@loongson.cn>
+ */
+
+#include <drm/drm_vblank.h>
+
+#include "lsdc_drv.h"
+#include "lsdc_regs.h"
+#include "lsdc_irq.h"
+
+/* Function to be called in a threaded interrupt context. */
+irqreturn_t lsdc_irq_thread_cb(int irq, void *arg)
+{
+	struct drm_device *ddev = arg;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	struct drm_crtc *crtc;
+
+	/* trigger the vblank event */
+	if (ldev->irq_status & INT_CRTC0_VS) {
+		crtc = drm_crtc_from_index(ddev, 0);
+		drm_crtc_handle_vblank(crtc);
+	}
+
+	if (ldev->irq_status & INT_CRTC1_VS) {
+		crtc = drm_crtc_from_index(ddev, 1);
+		drm_crtc_handle_vblank(crtc);
+	}
+
+	writel(INT_CRTC0_VS_EN | INT_CRTC1_VS_EN, ldev->reg_base + LSDC_INT_REG);
+
+	return IRQ_HANDLED;
+}
+
+/* Function to be called when the IRQ occurs */
+irqreturn_t lsdc_irq_handler_cb(int irq, void *arg)
+{
+	struct drm_device *ddev = arg;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+
+	/* Read & Clear the interrupt status */
+	ldev->irq_status = readl(ldev->reg_base + LSDC_INT_REG);
+	if ((ldev->irq_status & INT_STATUS_MASK) == 0) {
+		drm_warn(ddev, "no interrupt occurs\n");
+		return IRQ_NONE;
+	}
+
+	/* clear all interrupt */
+	writel(ldev->irq_status, ldev->reg_base + LSDC_INT_REG);
+
+	return IRQ_WAKE_THREAD;
+}

drivers/gpu/drm/loongson/lsdc_irq.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2022 Loongson Corporation
+ */
+
+/*
+ * Authors:
+ *      Sui Jingfeng <suijingfeng@loongson.cn>
+ */
+
+#ifndef __LSDC_IRQ_H__
+#define __LSDC_IRQ_H__
+
+irqreturn_t lsdc_irq_thread_cb(int irq, void *arg);
+irqreturn_t lsdc_irq_handler_cb(int irq, void *arg);
+
+#endif

drivers/gpu/drm/loongson/lsdc_output.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Loongson Corporation
+ */
+
+/*
+ * Authors:
+ *      Sui Jingfeng <suijingfeng@loongson.cn>
+ */
+
+#include <drm/drm_of.h>
+#include <drm/drm_edid.h>
+#include <drm/drm_probe_helper.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_connector.h>
+#include <drm/drm_bridge_connector.h>
+
+#include "lsdc_drv.h"
+#include "lsdc_i2c.h"
+#include "lsdc_output.h"
+#include "lsdc_regs.h"
+
+static int lsdc_get_modes(struct drm_connector *connector)
+{
+	unsigned int num = 0;
+	struct lsdc_output *lop = drm_connector_to_lsdc_output(connector);
+	struct lsdc_i2c *li2c = lop->li2c;
+	struct i2c_adapter *ddc = &li2c->adapter;
+
+	if (ddc) {
+		struct edid *edid;
+
+		edid = drm_get_edid(connector, ddc);
+		if (edid) {
+			drm_connector_update_edid_property(connector, edid);
+			num = drm_add_edid_modes(connector, edid);
+			kfree(edid);
+		}
+
+		return num;
+	}
+
+	drm_dbg(connector->dev, "Failed to get mode from ddc\n");
+
+	num = drm_add_modes_noedid(connector, 1920, 1200);
+
+	drm_set_preferred_mode(connector, 1024, 768);
+
+	return num;
+}
+
+static enum drm_connector_status
+lsdc_connector_detect(struct drm_connector *connector, bool force)
+{
+	struct lsdc_output *lop = drm_connector_to_lsdc_output(connector);
+	struct lsdc_i2c *li2c = lop->li2c;
+	struct i2c_adapter *ddc = &li2c->adapter;
+
+	if (ddc && drm_probe_ddc(ddc))
+		return connector_status_connected;
+
+	if (connector->connector_type == DRM_MODE_CONNECTOR_VIRTUAL)
+		return connector_status_connected;
+
+	if (connector->connector_type == DRM_MODE_CONNECTOR_DVIA ||
+	    connector->connector_type == DRM_MODE_CONNECTOR_DVID ||
+	    connector->connector_type == DRM_MODE_CONNECTOR_DVII)
+		return connector_status_disconnected;
+
+	if (connector->connector_type == DRM_MODE_CONNECTOR_HDMIA ||
+	    connector->connector_type == DRM_MODE_CONNECTOR_HDMIB)
+		return connector_status_disconnected;
+
+	return connector_status_unknown;
+}
+
+static void lsdc_connector_destroy(struct drm_connector *connector)
+{
+	drm_connector_cleanup(connector);
+}
+
+static const struct drm_connector_helper_funcs lsdc_connector_helpers = {
+	.get_modes = lsdc_get_modes,
+};
+
+static const struct drm_connector_funcs lsdc_connector_funcs = {
+	.dpms = drm_helper_connector_dpms,
+	.detect = lsdc_connector_detect,
+	.fill_modes = drm_helper_probe_single_connector_modes,
+	.destroy = lsdc_connector_destroy,
+	.reset = drm_atomic_helper_connector_reset,
+	.atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
+	.atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
+};
+
+static enum drm_mode_status
+ls7a2000_hdmi_encoder_mode_valid(struct drm_encoder *crtc,
+				  const struct drm_display_mode *mode)
+{
+	return MODE_OK;
+}
+
+static void ls7a2000_hdmi_encoder_disable(struct drm_encoder *encoder)
+{
+	int index = encoder->index;
+	struct lsdc_device *ldev = to_lsdc(encoder->dev);
+
+	if (index == 0) {
+		/* Enable hdmi */
+		writel(0, ldev->reg_base + HDMI0_CTRL_REG);
+
+	} else if (index == 1) {
+		/* Enable hdmi */
+		writel(0, ldev->reg_base + HDMI1_CTRL_REG);
+	}
+
+	drm_dbg(encoder->dev, "HDMI%d disable\n", index);
+}
+
+static void ls7a2000_hdmi_encoder_enable(struct drm_encoder *encoder)
+{
+	int index = encoder->index;
+	struct lsdc_device *ldev = to_lsdc(encoder->dev);
+
+	if (index == 0) {
+		/* Enable hdmi */
+		writel(0x280 | HDMI_EN | HDMI_PACKET_EN, ldev->reg_base + HDMI0_CTRL_REG);
+
+		/* hdmi zone idle */
+		writel(0x00400040, ldev->reg_base + HDMI0_ZONE_REG);
+	} else if (index == 1) {
+		/* Enable hdmi */
+		writel(0x280 | HDMI_EN | HDMI_PACKET_EN, ldev->reg_base + HDMI1_CTRL_REG);
+
+		/* hdmi zone idle */
+		writel(0x00400040, ldev->reg_base + HDMI1_ZONE_REG);
+	}
+
+	drm_dbg(encoder->dev, "HDMI%d enable\n", index);
+}
+
+static void
+ls7a2000_hdmi_encoder_mode_set(struct drm_encoder *encoder,
+			       struct drm_display_mode *mode,
+			       struct drm_display_mode *adjusted_mode)
+{
+	int index = encoder->index;
+	struct drm_device *ddev = encoder->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	int clock = mode->clock;
+	u32 val;
+	int counter;
+
+	if (index == 0) {
+		writel(0x0, ldev->reg_base + HDMI0_PLL_REG);
+		writel(0x0, ldev->reg_base + HDMI0_PHY_CTRL_REG);
+	} else {
+		writel(0x0, ldev->reg_base + HDMI1_PLL_REG);
+		writel(0x0, ldev->reg_base + HDMI1_PHY_CTRL_REG);
+	}
+
+	if (clock >= 170000)
+		val = (0x0 << 13) | (0x28 << 6) | (0x10 << 1) | HDMI_PLL_EN;
+	else if (clock >= 85000 && clock < 170000)
+		val = (0x1 << 13) | (0x28 << 6) | (0x8 << 1) | HDMI_PLL_EN;
+	else if (clock >= 42500 && clock < 85000)
+		val = (0x2 << 13) | (0x28 << 6) | (0x4 << 1) | HDMI_PLL_EN;
+	else if (clock >= 21250 && clock < 42500)
+		val = (0x3 << 13) | (0x28 << 6) | (0x2 << 1) | HDMI_PLL_EN;
+
+	if (index == 0) {
+		writel(val, ldev->reg_base + HDMI0_PLL_REG);
+	} else {
+		writel(val, ldev->reg_base + HDMI1_PLL_REG);
+	}
+
+	do {
+		/* wait pll lock */
+		if (index == 0)
+			val = readl(ldev->reg_base + HDMI0_PLL_REG);
+		else if (index == 1)
+			val = readl(ldev->reg_base + HDMI1_PLL_REG);
+
+		++counter;
+	} while (((val & HDMI_PLL_LOCKED) == 0) && (counter < 1000));
+
+	drm_dbg(ddev, "HDMI%d modeset, PLL: %u loop waited\n", index, counter);
+
+	if (index == 0) {
+		writel(0x0f03, ldev->reg_base + HDMI0_PHY_CTRL_REG);
+	} else if (index == 1) {
+		writel(0x0f03, ldev->reg_base + HDMI1_PHY_CTRL_REG);
+	}
+}
+
+static const struct drm_encoder_helper_funcs ls7a2000_hdmi_encoder_helper_funcs = {
+	.mode_valid = ls7a2000_hdmi_encoder_mode_valid,
+	.disable = ls7a2000_hdmi_encoder_disable,
+	.enable = ls7a2000_hdmi_encoder_enable,
+	.mode_set = ls7a2000_hdmi_encoder_mode_set,
+};
+
+static void lsdc_encoder_reset(struct drm_encoder *encoder)
+{
+	struct lsdc_device *ldev = to_lsdc(encoder->dev);
+
+	if (ldev->desc->chip == LSDC_CHIP_7A2000)
+		ls7a2000_hdmi_encoder_enable(encoder);
+}
+
+static const struct drm_encoder_funcs lsdc_encoder_funcs = {
+	.reset = lsdc_encoder_reset,
+	.destroy = drm_encoder_cleanup,
+};
+
+static int lsdc_attach_bridges(struct lsdc_device *ldev,
+			       struct device_node *ports,
+			       unsigned int i)
+{
+	struct lsdc_display_pipe * const dispipe = &ldev->dispipe[i];
+	struct drm_device *ddev = ldev->ddev;
+	struct drm_bridge *bridge;
+	struct drm_panel *panel;
+	struct drm_connector *connector;
+	struct drm_encoder *encoder;
+	struct lsdc_output *output;
+	int ret;
+
+	ret = drm_of_find_panel_or_bridge(ports, i, 0, &panel, &bridge);
+
+	if (panel) {
+		bridge = devm_drm_panel_bridge_add_typed(ddev->dev, panel, DRM_MODE_CONNECTOR_DPI);
+		drm_info(ddev, "output-%u is a DPI panel\n", i);
+	}
+
+	if (!bridge)
+		return ret;
+
+	output = devm_kzalloc(ddev->dev, sizeof(*output), GFP_KERNEL);
+	if (!output)
+		return -ENOMEM;
+
+	encoder = &output->encoder;
+
+	ret = drm_encoder_init(ddev, encoder, &lsdc_encoder_funcs,
+			       DRM_MODE_ENCODER_DPI, "encoder-%u", i);
+
+	if (ret) {
+		drm_err(ddev, "Failed to init encoder: %d\n", ret);
+		return ret;
+	}
+
+	encoder->possible_crtcs = BIT(i);
+
+	ret = drm_bridge_attach(encoder, bridge, NULL, DRM_BRIDGE_ATTACH_NO_CONNECTOR);
+	if (ret) {
+		drm_err(ddev,
+			"failed to attach bridge %pOF for output %u (%d)\n",
+			bridge->of_node, i, ret);
+		return ret;
+	}
+
+	connector = drm_bridge_connector_init(ddev, encoder);
+	if (IS_ERR(connector)) {
+		drm_err(ddev, "Unable to init connector\n");
+		return PTR_ERR(connector);
+	}
+
+	drm_connector_attach_encoder(connector, encoder);
+
+	drm_info(ddev, "bridge-%u attached to %s\n", i, encoder->name);
+
+	dispipe->output = output;
+
+	return 0;
+}
+
+int lsdc_attach_output(struct lsdc_device *ldev, uint32_t num_crtc)
+{
+	struct drm_device *ddev = ldev->ddev;
+	struct device_node *ports;
+	struct lsdc_display_pipe *disp;
+	unsigned int i;
+	int ret;
+
+	ldev->num_output = 0;
+
+	ports = of_get_child_by_name(ldev->dev->of_node, "ports");
+
+	for (i = 0; i < num_crtc; i++) {
+		struct drm_bridge *b;
+		struct drm_panel *p;
+
+		disp = &ldev->dispipe[i];
+		disp->available = false;
+
+		ret = drm_of_find_panel_or_bridge(ports, i, 0, &p, &b);
+		if (ret) {
+			if (ret == -ENODEV) {
+				drm_dbg(ddev, "No active panel or bridge for port%u\n", i);
+				disp->available = false;
+				continue;
+			}
+
+			if (ret == -EPROBE_DEFER)
+				drm_dbg(ddev, "Bridge for port%d is defer probed\n", i);
+
+			goto RET;
+		}
+
+		disp->available = true;
+		ldev->num_output++;
+	}
+
+	if (ldev->num_output == 0) {
+		drm_err(ddev, "No valid output, abort\n");
+		ret = -ENODEV;
+		goto RET;
+	}
+
+	for (i = 0; i < num_crtc; i++) {
+		disp = &ldev->dispipe[i];
+		if (disp->available) {
+			ret = lsdc_attach_bridges(ldev, ports, i);
+			if (ret)
+				goto RET;
+		} else {
+			drm_info(ddev, "output-%u is not available\n", i);
+		}
+	}
+
+	drm_info(ddev, "number of outputs: %u\n", ldev->num_output);
+RET:
+	of_node_put(ports);
+	return ret;
+}
+
+/* No DT support, provide a minimal support */
+int lsdc_create_output(struct lsdc_device *ldev,
+		       unsigned int index,
+		       unsigned int num_crtc)
+{
+	const struct lsdc_chip_desc * const descp = ldev->desc;
+	struct lsdc_display_pipe * const dispipe = &ldev->dispipe[index];
+	struct drm_device *ddev = ldev->ddev;
+	int encoder_type = DRM_MODE_ENCODER_DPI;
+	int connector_type = DRM_MODE_CONNECTOR_DPI;
+	struct lsdc_output *output;
+	struct drm_encoder *encoder;
+	struct drm_connector *connector;
+	int ret;
+
+	output = devm_kzalloc(ddev->dev, sizeof(*output), GFP_KERNEL);
+	if (!output)
+		return -ENOMEM;
+
+	encoder = &output->encoder;
+
+	if (descp->chip == LSDC_CHIP_7A2000) {
+		encoder_type = DRM_MODE_ENCODER_TMDS;
+		connector_type = DRM_MODE_CONNECTOR_HDMIA;
+	}
+
+	ret = drm_encoder_init(ddev, encoder, &lsdc_encoder_funcs,
+			       encoder_type, "encoder-%u", index);
+
+	if (ret) {
+		drm_err(ddev, "Failed to init encoder: %d\n", ret);
+		return ret;
+	}
+
+	if (descp->chip == LSDC_CHIP_7A2000)
+		drm_encoder_helper_add(encoder, &ls7a2000_hdmi_encoder_helper_funcs);
+
+	encoder->possible_crtcs = BIT(index);
+
+	if (descp->has_builtin_i2c) {
+		output->li2c = lsdc_create_i2c_chan(ddev, ldev->reg_base, index);
+		if (IS_ERR(output->li2c)) {
+			drm_err(ddev, "Failed to create i2c adapter\n");
+			return PTR_ERR(output->li2c);
+		}
+	} else {
+		drm_warn(ddev, "output-%u don't has ddc\n", index);
+		output->li2c = NULL;
+	}
+
+	connector = &output->connector;
+
+	ret = drm_connector_init_with_ddc(ddev,
+					  connector,
+					  &lsdc_connector_funcs,
+					  connector_type,
+					  &output->li2c->adapter);
+	if (ret) {
+		drm_err(ddev, "Init connector%d failed\n", index);
+		return ret;
+	}
+
+	drm_connector_helper_add(connector, &lsdc_connector_helpers);
+
+	connector->polled = DRM_CONNECTOR_POLL_CONNECT | DRM_CONNECTOR_POLL_DISCONNECT;
+
+	drm_connector_attach_encoder(connector, encoder);
+
+	dispipe->available = true;
+	dispipe->output = output;
+	ldev->num_output++;
+
+	return 0;
+}

drivers/gpu/drm/loongson/lsdc_output.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2022 Loongson Corporation
+ */
+
+/*
+ * Authors:
+ *      Sui Jingfeng <suijingfeng@loongson.cn>
+ */
+
+#ifndef __LSDC_OUTPUT_H__
+#define __LSDC_OUTPUT_H__
+
+#include <drm/drm_device.h>
+#include <drm/drm_connector.h>
+
+int lsdc_create_output(struct lsdc_device *ldev, unsigned int i, unsigned int num_crtc);
+
+int lsdc_attach_output(struct lsdc_device *ldev, uint32_t num_crtc);
+
+#endif

drivers/gpu/drm/loongson/lsdc_pci_drv.c

+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * KMS driver for Loongson display controller
+ * Copyright (C) 2022 Loongson Corporation
+ */
+
+/*
+ * Authors:
+ *      Sui Jingfeng <suijingfeng@loongson.cn>
+ */
+
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/platform_device.h>
+
+#include <drm/drm_modeset_helper.h>
+
+#include "lsdc_drv.h"
+#include "lsdc_i2c.h"
+
+static int lsdc_use_vram_helper = -1;
+MODULE_PARM_DESC(use_vram_helper, "Using vram helper based driver(0 = disabled)");
+module_param_named(use_vram_helper, lsdc_use_vram_helper, int, 0644);
+
+static int lsdc_gamma = -1;
+MODULE_PARM_DESC(gamma, "enable gamma (-1 = disabled (default), >0 = enabled)");
+module_param_named(gamma, lsdc_gamma, int, 0644);
+
+static int lsdc_relax_alignment = -1;
+MODULE_PARM_DESC(relax_alignment,
+		 "relax crtc stride alignment (-1 = disabled (default), >0 = enabled)");
+module_param_named(relax_alignment, lsdc_relax_alignment, int, 0644);
+
+
+static struct platform_device *
+lsdc_create_platform_device(const char *name,
+			    struct device *parent,
+			    const struct lsdc_chip_desc *descp,
+			    struct resource *res)
+{
+	struct device *dev;
+	struct platform_device *pdev;
+	int ret;
+
+	pdev = platform_device_alloc(name, PLATFORM_DEVID_NONE);
+	if (!pdev) {
+		dev_err(parent, "can not create platform device\n");
+		return ERR_PTR(-ENOMEM);
+	}
+
+	dev_info(parent, "platform device %s created\n", name);
+
+	dev = &pdev->dev;
+	dev->parent = parent;
+
+	if (descp) {
+		ret = platform_device_add_data(pdev, descp, sizeof(*descp));
+		if (ret) {
+			dev_err(parent, "add platform data failed: %d\n", ret);
+			goto ERROR_RET;
+		}
+	}
+
+	if (res) {
+		ret = platform_device_add_resources(pdev, res, 1);
+		if (ret) {
+			dev_err(parent, "add platform resources failed: %d\n", ret);
+			goto ERROR_RET;
+		}
+	}
+
+	ret = platform_device_add(pdev);
+	if (ret) {
+		dev_err(parent, "add platform device failed: %d\n", ret);
+		goto ERROR_RET;
+	}
+
+	return pdev;
+
+ERROR_RET:
+	platform_device_put(pdev);
+	return ERR_PTR(ret);
+}
+
+static int lsdc_vram_init(struct lsdc_device *ldev)
+{
+	const struct lsdc_chip_desc * const descp = ldev->desc;
+	struct pci_dev *gpu;
+	resource_size_t base, size;
+
+	if (descp->chip == LSDC_CHIP_7A2000) {
+		/* BAR 2 of LS7A2000's GPU contain VRAM */
+		gpu = pci_get_device(PCI_VENDOR_ID_LOONGSON, 0x7A25, NULL);
+	} else if (descp->chip == LSDC_CHIP_7A1000) {
+		/* BAR 2 of LS7A1000's GPU(GC1000) contain VRAM */
+		gpu = pci_get_device(PCI_VENDOR_ID_LOONGSON, 0x7A15, NULL);
+	} else {
+		dev_err(ldev->dev, "Unknown chip, the driver need update\n");
+		return -ENOENT;
+	}
+
+	if (IS_ERR_OR_NULL(gpu)) {
+		dev_err(ldev->dev, "Can not get VRAM\n");
+		return -ENOENT;
+	}
+
+	base = pci_resource_start(gpu, 2);
+	size =  pci_resource_len(gpu, 2);
+
+	ldev->vram_base = base;
+	ldev->vram_size = size;
+
+	dev_info(ldev->dev, "vram start: 0x%llx, size: %uMB\n",
+		 (u64)base, (u32)(size >> 20));
+
+	return 0;
+}
+
+static void lsdc_of_probe(struct lsdc_device *ldev, struct device_node *np)
+{
+	struct device_node *ports;
+
+	if (!np) {
+		ldev->has_dt = false;
+		ldev->has_ports_node = false;
+		dev_info(ldev->dev, "don't has DT support\n");
+		return;
+	}
+
+	ports = of_get_child_by_name(np, "ports");
+	ldev->has_ports_node = ports ? true : false;
+	of_node_put(ports);
+}
+
+static int lsdc_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+	struct device *dev = &pdev->dev;
+	const struct lsdc_chip_desc *descp;
+	struct lsdc_device *ldev;
+	int ret;
+
+	descp = lsdc_detect_chip(pdev, ent);
+	if (!descp) {
+		dev_info(dev, "unknown dc ip core, abort\n");
+		return -ENOENT;
+	}
+
+	ldev = devm_kzalloc(dev, sizeof(*ldev), GFP_KERNEL);
+	if (IS_ERR(ldev))
+		return PTR_ERR(ldev);
+
+	ldev->desc = descp;
+	ldev->dev = dev;
+
+	if (lsdc_use_vram_helper > 0)
+		ldev->use_vram_helper = true;
+	else if ((lsdc_use_vram_helper < 0) && descp->has_vram)
+		ldev->use_vram_helper = true;
+	else
+		ldev->use_vram_helper = false;
+
+	if (!descp->broken_gamma)
+		ldev->enable_gamma = true;
+	else
+		ldev->enable_gamma = lsdc_gamma > 0 ? true : false;
+
+	ldev->relax_alignment = lsdc_relax_alignment > 0 ? true : false;
+
+	lsdc_of_probe(ldev, dev->of_node);
+
+	ret = pcim_enable_device(pdev);
+	if (ret)
+		return ret;
+
+	pci_set_master(pdev);
+
+	/* BAR 0 contains registers */
+	ldev->reg_base = devm_ioremap_resource(dev, &pdev->resource[0]);
+	if (IS_ERR(ldev->reg_base))
+		return PTR_ERR(ldev->reg_base);
+
+	/* Create GPIO emulated i2c driver as early as possible */
+	if (descp->has_builtin_i2c && ldev->has_ports_node) {
+		struct device_node *i2c_node;
+
+		for_each_compatible_node(i2c_node, NULL, "loongson,gpio-i2c") {
+			if (!of_device_is_available(i2c_node))
+				continue;
+
+			lsdc_of_create_i2c_adapter(dev, ldev->reg_base, i2c_node);
+		}
+	}
+
+	if (ldev->has_dt) {
+		/* Get the optional framebuffer memory resource */
+		ret = of_reserved_mem_device_init(dev);
+		if (ret && (ret != -ENODEV))
+			return ret;
+	}
+
+	if (descp->has_vram && ldev->use_vram_helper) {
+		ret = lsdc_vram_init(ldev);
+		if (ret) {
+			dev_err(dev, "VRAM is unavailable\n");
+			ldev->use_vram_helper = false;
+		}
+	}
+
+	ldev->irq = pdev->irq;
+
+	dev_set_drvdata(dev, ldev);
+
+	if (descp->has_vram && ldev->use_vram_helper) {
+		struct resource res;
+
+		memset(&res, 0, sizeof(res));
+		res.flags = IORESOURCE_MEM;
+		res.name = "LS7A_VRAM";
+		res.start = ldev->vram_base;
+		res.end = ldev->vram_size;
+	}
+
+	ldev->dc = lsdc_create_platform_device("lsdc", dev, descp, NULL);
+	if (IS_ERR(ldev->dc))
+		return PTR_ERR(ldev->dc);
+
+	return platform_driver_register(&lsdc_platform_driver);
+}
+
+static void lsdc_pci_remove(struct pci_dev *pdev)
+{
+	struct lsdc_device *ldev = pci_get_drvdata(pdev);
+
+	platform_device_unregister(ldev->dc);
+
+	pci_set_drvdata(pdev, NULL);
+
+	pci_clear_master(pdev);
+
+	pci_release_regions(pdev);
+}
+
+static int lsdc_drm_suspend(struct device *dev)
+{
+	struct lsdc_device *ldev = dev_get_drvdata(dev);
+
+	return drm_mode_config_helper_suspend(ldev->ddev);
+}
+
+static int lsdc_drm_resume(struct device *dev)
+{
+	struct lsdc_device *ldev = dev_get_drvdata(dev);
+
+	return drm_mode_config_helper_resume(ldev->ddev);
+}
+
+static int lsdc_pm_freeze(struct device *dev)
+{
+	return lsdc_drm_suspend(dev);
+}
+
+static int lsdc_pm_thaw(struct device *dev)
+{
+	return lsdc_drm_resume(dev);
+}
+
+static int lsdc_pm_suspend(struct device *dev)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	int error;
+
+	error = lsdc_pm_freeze(dev);
+	if (error)
+		return error;
+
+	pci_save_state(pdev);
+	/* Shut down the device */
+	pci_disable_device(pdev);
+	pci_set_power_state(pdev, PCI_D3hot);
+
+	return 0;
+}
+
+static int lsdc_pm_resume(struct device *dev)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+
+	if (pcim_enable_device(pdev))
+		return -EIO;
+
+	pci_set_power_state(pdev, PCI_D0);
+
+	pci_restore_state(pdev);
+
+	return lsdc_pm_thaw(dev);
+}
+
+static const struct dev_pm_ops lsdc_pm_ops = {
+	.suspend = lsdc_pm_suspend,
+	.resume = lsdc_pm_resume,
+	.freeze = lsdc_pm_freeze,
+	.thaw = lsdc_pm_thaw,
+	.poweroff = lsdc_pm_freeze,
+	.restore = lsdc_pm_resume,
+};
+
+static const struct pci_device_id lsdc_pciid_list[] = {
+	{PCI_VENDOR_ID_LOONGSON, 0x7a06, PCI_ANY_ID, PCI_ANY_ID, 0, 0, (kernel_ulong_t)LSDC_CHIP_7A1000},
+	{PCI_VENDOR_ID_LOONGSON, 0x7a36, PCI_ANY_ID, PCI_ANY_ID, 0, 0, (kernel_ulong_t)LSDC_CHIP_7A2000},
+	{0, 0, 0, 0, 0, 0, 0}
+};
+
+static struct pci_driver lsdc_pci_driver = {
+	.name = DRIVER_NAME,
+	.id_table = lsdc_pciid_list,
+	.probe = lsdc_pci_probe,
+	.remove = lsdc_pci_remove,
+	.driver.pm = &lsdc_pm_ops,
+};
+
+static int __init lsdc_drm_init(void)
+{
+	struct pci_dev *pdev = NULL;
+
+	while ((pdev = pci_get_class(PCI_CLASS_DISPLAY_VGA << 8, pdev))) {
+		/*
+		 * Multiple video card workaround
+		 *
+		 * This integrated video card will always be selected as
+		 * default boot device by vgaarb subsystem.
+		 */
+		if (pdev->vendor != PCI_VENDOR_ID_LOONGSON) {
+			pr_info("Discrete graphic card detected, abort\n");
+			return 0;
+		}
+	}
+
+	return pci_register_driver(&lsdc_pci_driver);
+}
+module_init(lsdc_drm_init);
+
+static void __exit lsdc_drm_exit(void)
+{
+	pci_unregister_driver(&lsdc_pci_driver);
+}
+module_exit(lsdc_drm_exit);
+
+MODULE_DEVICE_TABLE(pci, lsdc_pciid_list);
+MODULE_AUTHOR(DRIVER_AUTHOR);
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE("GPL v2");

drivers/gpu/drm/loongson/lsdc_plane.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Loongson Corporation
+ */
+
+/*
+ * Authors:
+ *      Sui Jingfeng <suijingfeng@loongson.cn>
+ */
+#include <drm/drm_fourcc.h>
+#include <drm/drm_atomic.h>
+#include <drm/drm_format_helper.h>
+#include <drm/drm_plane_helper.h>
+#include <drm/drm_fb_cma_helper.h>
+#include <drm/drm_gem_cma_helper.h>
+#include <drm/drm_gem_vram_helper.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_gem_framebuffer_helper.h>
+
+#include "lsdc_drv.h"
+#include "lsdc_regs.h"
+
+static const u32 lsdc_primary_formats[] = {
+	DRM_FORMAT_RGB565,
+	DRM_FORMAT_XRGB8888,
+	DRM_FORMAT_ARGB8888,
+};
+
+static const u32 lsdc_cursor_formats[] = {
+	DRM_FORMAT_ARGB8888,
+};
+
+static const u64 lsdc_fb_format_modifiers[] = {
+	DRM_FORMAT_MOD_LINEAR,
+	DRM_FORMAT_MOD_INVALID
+};
+
+static void lsdc_update_fb_format(struct lsdc_device *ldev,
+				  struct drm_crtc *crtc,
+				  const struct drm_format_info *fmt_info)
+{
+	unsigned int index = drm_crtc_index(crtc);
+	u32 val = 0;
+	u32 fmt;
+
+	switch (fmt_info->format) {
+	case DRM_FORMAT_RGB565:
+		fmt = LSDC_PF_RGB565;
+		break;
+	case DRM_FORMAT_XRGB8888:
+		fmt = LSDC_PF_XRGB8888;
+		break;
+	case DRM_FORMAT_ARGB8888:
+		fmt = LSDC_PF_XRGB8888;
+		break;
+	default:
+		fmt = LSDC_PF_XRGB8888;
+		break;
+	}
+
+	if (index == 0) {
+		val = readl(ldev->reg_base + LSDC_CRTC0_CFG_REG);
+		val = (val & ~CFG_PIX_FMT_MASK) | fmt;
+		writel(val, ldev->reg_base + LSDC_CRTC0_CFG_REG);
+	} else if (index == 1) {
+		val = readl(ldev->reg_base + LSDC_CRTC1_CFG_REG);
+		val = (val & ~CFG_PIX_FMT_MASK) | fmt;
+		writel(val, ldev->reg_base + LSDC_CRTC1_CFG_REG);
+	}
+}
+
+static void lsdc_update_fb_start_addr(struct lsdc_device *ldev,
+				      struct drm_crtc *crtc,
+				      u64 paddr)
+{
+	unsigned int index = drm_crtc_index(crtc);
+	u32 lo32_addr_reg;
+	u32 hi32_addr_reg;
+	u32 cfg_reg;
+	u32 val;
+
+	/*
+	 * Find which framebuffer address register should update.
+	 * if FB_ADDR0_REG is in using, we write the addr to FB_ADDR1_REG,
+	 * if FB_ADDR1_REG is in using, we write the addr to FB_ADDR0_REG
+	 */
+	if (index == 0) {
+		/* CRTC0 */
+		val = readl(ldev->reg_base + LSDC_CRTC0_CFG_REG);
+
+		cfg_reg = LSDC_CRTC0_CFG_REG;
+		hi32_addr_reg = LSDC_CRTC0_FB_HI_ADDR_REG;
+
+		if (val & CFG_FB_IDX_BIT)
+			lo32_addr_reg = LSDC_CRTC0_FB_ADDR0_REG;
+		else
+			lo32_addr_reg = LSDC_CRTC0_FB_ADDR1_REG;
+	} else if (index == 1) {
+		/* CRTC1 */
+		val = readl(ldev->reg_base + LSDC_CRTC1_CFG_REG);
+
+		cfg_reg = LSDC_CRTC1_CFG_REG;
+		hi32_addr_reg = LSDC_CRTC1_FB_HI_ADDR_REG;
+
+		if (val & CFG_FB_IDX_BIT)
+			lo32_addr_reg = LSDC_CRTC1_FB_ADDR0_REG;
+		else
+			lo32_addr_reg = LSDC_CRTC1_FB_ADDR1_REG;
+	}
+
+	drm_dbg(ldev->ddev, "crtc%u scantout from 0x%llx\n", index, paddr);
+
+	/* The bridge's bus width is 40 */
+	writel(paddr, ldev->reg_base + lo32_addr_reg);
+	writel((paddr >> 32) & 0xFF, ldev->reg_base + hi32_addr_reg);
+	/*
+	 * Then, we triger the fb switch, the switch of the framebuffer
+	 * to be scanout will complete at the next vblank.
+	 */
+	writel(val | CFG_PAGE_FLIP_BIT, ldev->reg_base + cfg_reg);
+}
+
+static unsigned int lsdc_get_fb_offset(struct drm_framebuffer *fb,
+				       struct drm_plane_state *state,
+				       unsigned int plane)
+{
+	unsigned int offset = fb->offsets[plane];
+
+	offset += fb->format->cpp[plane] * (state->src_x >> 16);
+	offset += fb->pitches[plane] * (state->src_y >> 16);
+
+	return offset;
+}
+
+static s64 lsdc_get_vram_bo_offset(struct drm_framebuffer *fb)
+{
+	struct drm_gem_vram_object *gbo;
+	s64 gpu_addr;
+
+	gbo = drm_gem_vram_of_gem(fb->obj[0]);
+	gpu_addr = drm_gem_vram_offset(gbo);
+
+	return gpu_addr;
+}
+
+static int lsdc_primary_plane_atomic_check(struct drm_plane *plane,
+					   struct drm_plane_state *state)
+{
+	struct drm_crtc *crtc = state->crtc;
+	struct drm_crtc_state *crtc_state;
+	struct drm_framebuffer *fb = state->fb;
+
+	/* no need for further checks if the plane is being disabled */
+	if (!crtc || !fb)
+		return 0;
+
+	crtc_state = drm_atomic_get_crtc_state(state->state, crtc);
+	if (WARN_ON(!crtc_state))
+		return -EINVAL;
+
+	return drm_atomic_helper_check_plane_state(plane->state,
+						   crtc_state,
+						   DRM_PLANE_HELPER_NO_SCALING,
+						   DRM_PLANE_HELPER_NO_SCALING,
+						   false, true);
+}
+
+static void lsdc_update_stride(struct lsdc_device *ldev,
+			       struct drm_crtc *crtc,
+			       unsigned int stride)
+{
+	unsigned int index = drm_crtc_index(crtc);
+
+	if (index == 0)
+		writel(stride, ldev->reg_base + LSDC_CRTC0_STRIDE_REG);
+	else if (index == 1)
+		writel(stride, ldev->reg_base + LSDC_CRTC1_STRIDE_REG);
+
+	drm_dbg(ldev->ddev, "update stride to %u\n", stride);
+}
+
+static void lsdc_primary_plane_atomic_update(struct drm_plane *plane,
+					     struct drm_plane_state *old_state)
+{
+	struct drm_device *ddev = plane->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	struct drm_plane_state *new_plane_state = plane->state;
+	struct drm_crtc *crtc = new_plane_state->crtc;
+	struct drm_framebuffer *fb = new_plane_state->fb;
+	u32 fb_offset = lsdc_get_fb_offset(fb, new_plane_state, 0);
+	dma_addr_t fb_addr;
+
+	if (ldev->use_vram_helper) {
+		s64 gpu_addr;
+
+		gpu_addr = lsdc_get_vram_bo_offset(fb);
+		if (gpu_addr < 0)
+			return;
+
+		fb_addr = ldev->vram_base + gpu_addr + fb_offset;
+	} else {
+		struct drm_gem_cma_object *obj = drm_fb_cma_get_gem_obj(fb, 0);
+
+		fb_addr = obj->paddr + fb_offset;
+	}
+
+	lsdc_update_fb_start_addr(ldev, crtc, fb_addr);
+
+	lsdc_update_stride(ldev, crtc, fb->pitches[0]);
+
+	if (drm_atomic_crtc_needs_modeset(crtc->state))
+		lsdc_update_fb_format(ldev, crtc, fb->format);
+}
+
+static void lsdc_primary_plane_atomic_disable(struct drm_plane *plane,
+					      struct drm_plane_state *old_state)
+{
+	drm_dbg(plane->dev, "%s disabled\n", plane->name);
+}
+
+static int lsdc_plane_prepare_fb(struct drm_plane *plane,
+				 struct drm_plane_state *new_state)
+{
+	struct lsdc_device *ldev = to_lsdc(plane->dev);
+
+	if (ldev->use_vram_helper)
+		return drm_gem_vram_plane_helper_prepare_fb(plane, new_state);
+
+	return drm_gem_fb_prepare_fb(plane, new_state);
+}
+
+static void lsdc_plane_cleanup_fb(struct drm_plane *plane,
+				  struct drm_plane_state *old_state)
+{
+	struct drm_device *ddev = plane->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+
+	if (ldev->use_vram_helper)
+		return drm_gem_vram_plane_helper_cleanup_fb(plane, old_state);
+}
+
+static const struct drm_plane_helper_funcs lsdc_primary_plane_helpers = {
+	.prepare_fb = lsdc_plane_prepare_fb,
+	.cleanup_fb = lsdc_plane_cleanup_fb,
+	.atomic_check = lsdc_primary_plane_atomic_check,
+	.atomic_update = lsdc_primary_plane_atomic_update,
+	.atomic_disable = lsdc_primary_plane_atomic_disable,
+};
+
+static int lsdc_cursor_atomic_check(struct drm_plane *plane,
+				    struct drm_plane_state *state)
+{
+	struct drm_framebuffer *fb = state->fb;
+	struct drm_crtc *crtc = state->crtc;
+	struct drm_crtc_state *crtc_state;
+
+	/* no need for further checks if the plane is being disabled */
+	if (!crtc || !fb)
+		return 0;
+
+	if (!state->visible)
+		return 0;
+
+	crtc_state = drm_atomic_get_crtc_state(state->state, crtc);
+	if (WARN_ON(!crtc_state))
+		return -EINVAL;
+
+	return drm_atomic_helper_check_plane_state(state,
+						   crtc_state,
+						   DRM_PLANE_HELPER_NO_SCALING,
+						   DRM_PLANE_HELPER_NO_SCALING,
+						   true,
+						   true);
+}
+
+static void lsdc_cursor_atomic_update(struct drm_plane *plane,
+				      struct drm_plane_state *old_plane_state)
+{
+	struct lsdc_display_pipe * const dispipe = lsdc_cursor_to_dispipe(plane);
+	struct drm_device *ddev = plane->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	const struct lsdc_chip_desc * const descp = ldev->desc;
+	struct drm_plane_state *new_plane_state = plane->state;
+	struct drm_framebuffer *new_fb = new_plane_state->fb;
+	struct drm_framebuffer *old_fb = old_plane_state->fb;
+	int dst_x = new_plane_state->crtc_x;
+	int dst_y = new_plane_state->crtc_y;
+	u32 val;
+
+	if (new_fb != old_fb) {
+		u64 cursor_addr;
+
+		if (ldev->use_vram_helper) {
+			s64 offset;
+
+			offset = lsdc_get_vram_bo_offset(new_fb);
+			cursor_addr = ldev->vram_base + offset;
+
+			drm_dbg(ddev, "%s offset: %llx\n", plane->name, offset);
+		} else {
+			struct drm_gem_cma_object *cursor_obj;
+
+			cursor_obj = drm_fb_cma_get_gem_obj(new_fb, 0);
+			if (!cursor_obj)
+				return;
+
+			cursor_addr = cursor_obj->paddr;
+		}
+
+		if ((descp->chip == LSDC_CHIP_7A2000) && (dispipe->index == 1))
+			writel(cursor_addr, ldev->reg_base + LSDC_CURSOR1_ADDR_REG);
+		else
+			writel(cursor_addr, ldev->reg_base + LSDC_CURSOR0_ADDR_REG);
+	}
+
+	/* Update cursor's position */
+	if (dst_x < 0)
+		dst_x = 0;
+
+	if (dst_y < 0)
+		dst_y = 0;
+
+	val = (dst_y << 16) | dst_x;
+
+	if ((descp->chip == LSDC_CHIP_7A2000) && (dispipe->index == 1))
+		writel(val, ldev->reg_base + LSDC_CURSOR1_POSITION_REG);
+	else
+		writel(val, ldev->reg_base + LSDC_CURSOR0_POSITION_REG);
+
+	/* Update cursor's location and format */
+	val = CURSOR_FORMAT_ARGB8888;
+
+	if (descp->chip == LSDC_CHIP_7A2000) {
+		/* LS7A2000 support 64x64 and 32x32 */
+		val |= CURSOR_SIZE_64X64;
+		if (dispipe->index == 1) {
+			val |= CURSOR_LOCATION_BIT;
+			writel(val, ldev->reg_base + LSDC_CURSOR1_CFG_REG);
+		} else if (dispipe->index == 0) {
+			val &= ~CURSOR_LOCATION_BIT;
+			writel(val, ldev->reg_base + LSDC_CURSOR0_CFG_REG);
+		}
+	} else {
+		/*
+		 * Update the location of the cursor
+		 * if bit 4 of LSDC_CURSOR_CFG_REG is 1, then the cursor will be
+		 * locate at CRTC1, if bit 4 of LSDC_CURSOR_CFG_REG is 0, then
+		 * the cursor will be locate at CRTC0.
+		 */
+		if (dispipe->index)
+			val |= CURSOR_LOCATION_BIT;
+
+		writel(val, ldev->reg_base + LSDC_CURSOR0_CFG_REG);
+	}
+}
+
+static void lsdc_cursor_atomic_disable(struct drm_plane *plane,
+				       struct drm_plane_state *old_state)
+{
+	const struct lsdc_display_pipe * const dispipe = lsdc_cursor_to_dispipe(plane);
+	struct drm_device *ddev = plane->dev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	const struct lsdc_chip_desc * const descp = ldev->desc;
+	u32 val;
+
+	if ((descp->chip == LSDC_CHIP_7A2000) && (dispipe->index == 1)) {
+		val = readl(ldev->reg_base + LSDC_CURSOR1_CFG_REG);
+		val &= ~CURSOR_FORMAT_MASK;
+		val |= CURSOR_FORMAT_DISABLE;
+		writel(val, ldev->reg_base + LSDC_CURSOR1_CFG_REG);
+	} else {
+		val = readl(ldev->reg_base + LSDC_CURSOR0_CFG_REG);
+		val &= ~CURSOR_FORMAT_MASK;
+		val |= CURSOR_FORMAT_DISABLE;
+		writel(val, ldev->reg_base + LSDC_CURSOR0_CFG_REG);
+	}
+
+	drm_dbg(ddev, "%s disabled\n", plane->name);
+}
+
+static const struct drm_plane_helper_funcs lsdc_cursor_plane_helpers = {
+	.prepare_fb = lsdc_plane_prepare_fb,
+	.cleanup_fb = lsdc_plane_cleanup_fb,
+	.atomic_check = lsdc_cursor_atomic_check,
+	.atomic_update = lsdc_cursor_atomic_update,
+	.atomic_disable = lsdc_cursor_atomic_disable,
+};
+
+static int lsdc_plane_get_default_zpos(enum drm_plane_type type)
+{
+	switch (type) {
+	case DRM_PLANE_TYPE_PRIMARY:
+		return 0;
+	case DRM_PLANE_TYPE_OVERLAY:
+		return 1;
+	case DRM_PLANE_TYPE_CURSOR:
+		return 7;
+	}
+
+	return 0;
+}
+
+static void lsdc_plane_reset(struct drm_plane *plane)
+{
+	drm_atomic_helper_plane_reset(plane);
+
+	plane->state->zpos = lsdc_plane_get_default_zpos(plane->type);
+
+	drm_dbg(plane->dev, "%s reset\n", plane->name);
+}
+
+static const struct drm_plane_funcs lsdc_plane_funcs = {
+	.update_plane = drm_atomic_helper_update_plane,
+	.disable_plane = drm_atomic_helper_disable_plane,
+	.destroy = drm_plane_cleanup,
+	.reset = lsdc_plane_reset,
+	.atomic_duplicate_state = drm_atomic_helper_plane_duplicate_state,
+	.atomic_destroy_state = drm_atomic_helper_plane_destroy_state,
+};
+
+int lsdc_plane_init(struct lsdc_device *ldev,
+		    struct drm_plane *plane,
+		    enum drm_plane_type type,
+		    unsigned int index)
+{
+	struct drm_device *ddev = ldev->ddev;
+	int zpos = lsdc_plane_get_default_zpos(type);
+	unsigned int format_count;
+	const u32 *formats;
+	const char *name;
+	int ret;
+
+	switch (type) {
+	case DRM_PLANE_TYPE_PRIMARY:
+		formats = lsdc_primary_formats;
+		format_count = ARRAY_SIZE(lsdc_primary_formats);
+		name = "primary-%u";
+		break;
+	case DRM_PLANE_TYPE_CURSOR:
+		formats = lsdc_cursor_formats;
+		format_count = ARRAY_SIZE(lsdc_cursor_formats);
+		name = "cursor-%u";
+		break;
+	case DRM_PLANE_TYPE_OVERLAY:
+		drm_err(ddev, "overlay plane is not supported\n");
+		break;
+	}
+
+	ret = drm_universal_plane_init(ddev, plane, 1 << index,
+				       &lsdc_plane_funcs,
+				       formats, format_count,
+				       lsdc_fb_format_modifiers,
+				       type, name, index);
+	if (ret) {
+		drm_err(ddev, "%s failed: %d\n", __func__, ret);
+		return ret;
+	}
+
+	switch (type) {
+	case DRM_PLANE_TYPE_PRIMARY:
+		drm_plane_helper_add(plane, &lsdc_primary_plane_helpers);
+		drm_plane_create_zpos_property(plane, zpos, 0, 6);
+		break;
+	case DRM_PLANE_TYPE_CURSOR:
+		drm_plane_helper_add(plane, &lsdc_cursor_plane_helpers);
+		drm_plane_create_zpos_immutable_property(plane, zpos);
+		break;
+	case DRM_PLANE_TYPE_OVERLAY:
+		drm_err(ddev, "overlay plane is not supported\n");
+		break;
+	}
+
+	drm_plane_create_alpha_property(plane);
+
+	return 0;
+}

drivers/gpu/drm/loongson/lsdc_pll.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Loongson Corporation
+ */
+
+/*
+ * Authors:
+ *      Sui Jingfeng <suijingfeng@loongson.cn>
+ */
+
+#include "lsdc_drv.h"
+#include "lsdc_regs.h"
+#include "lsdc_pll.h"
+
+/*
+ * The structure of the pixel PLL register is evolved with times.
+ * All loongson's cpu is little endian.
+ */
+
+/* u64 */
+struct ls7a1000_pixpll_bitmap {
+	/* Byte 0 ~ Byte 3 */
+	unsigned div_out      : 7;   /*  0 : 6     output clock divider  */
+	unsigned reserved_1   : 14;  /*  7 : 20                          */
+	unsigned loopc        : 9;   /* 21 : 29                          */
+	unsigned reserved_2   : 2;   /* 30 : 31                          */
+
+	/* Byte 4 ~ Byte 7 */
+	unsigned div_ref      : 7;   /*  0 : 6     input clock divider   */
+	unsigned locked       : 1;   /*  7         PLL locked flag       */
+	unsigned sel_out      : 1;   /*  8         output clk selector   */
+	unsigned reserved_3   : 2;   /*  9 : 10    reserved              */
+	unsigned set_param    : 1;   /*  11        set pll param         */
+	unsigned bypass       : 1;   /*  12                              */
+	unsigned powerdown    : 1;   /*  13                              */
+	unsigned reserved_4   : 18;  /*  14 : 31                         */
+};
+
+/* u128 */
+struct ls2k1000_pixpll_bitmap {
+	/* Byte 0 ~ Byte 3 */
+	unsigned sel_out      :  1;  /*  0      select this PLL          */
+	unsigned reserved_1   :  1;  /*  1                               */
+	unsigned sw_adj_en    :  1;  /*  2      allow software adjust    */
+	unsigned bypass       :  1;  /*  3      bypass L1 PLL            */
+	unsigned reserved_2   :  3;  /*  4:6                             */
+	unsigned lock_en      :  1;  /*  7      enable lock L1 PLL       */
+	unsigned reserved_3   :  2;  /*  8:9                             */
+	unsigned lock_check   :  2;  /* 10:11   precision check          */
+	unsigned reserved_4   :  4;  /* 12:15                            */
+
+	unsigned locked       :  1;  /* 16      PLL locked flag bit      */
+	unsigned reserved_5   :  2;  /* 17:18                            */
+	unsigned powerdown    :  1;  /* 19      powerdown the pll if set */
+	unsigned reserved_6   :  6;  /* 20:25                            */
+	unsigned div_ref      :  6;  /* 26:31   L1 Prescaler             */
+
+	/* Byte 4 ~ Byte 7 */
+	unsigned loopc        : 10;  /* 32:41   Clock Multiplier         */
+	unsigned l1_div       :  6;  /* 42:47   not used                 */
+	unsigned reserved_7   : 16;  /* 48:63                            */
+
+	/* Byte 8 ~ Byte 15 */
+	unsigned div_out      :  6;  /* 0 : 5   output clock divider     */
+	unsigned reserved_8   : 26;  /* 6 : 31                           */
+	unsigned reserved_9   : 32;  /* 70: 127                          */
+};
+
+/* u32 */
+struct ls2k0500_pixpll_bitmap {
+	/* Byte 0 ~ Byte 1 */
+	unsigned sel_out      : 1;
+	unsigned reserved_1   : 2;
+	unsigned sw_adj_en    : 1;   /* allow software adjust              */
+	unsigned bypass       : 1;   /* bypass L1 PLL                      */
+	unsigned powerdown    : 1;   /* write 1 to powerdown the PLL       */
+	unsigned reserved_2   : 1;
+	unsigned locked       : 1;   /*  7     Is L1 PLL locked, read only */
+	unsigned div_ref      : 6;   /*  8:13  ref clock divider           */
+	unsigned reserved_3   : 2;   /* 14:15                              */
+	/* Byte 2 ~ Byte 3 */
+	unsigned loopc        : 8;   /* 16:23   Clock Multiplier           */
+	unsigned div_out      : 6;   /* 24:29   output clock divider       */
+	unsigned reserved_4   : 2;   /* 30:31                              */
+};
+
+union lsdc_pixpll_bitmap {
+	struct ls7a1000_pixpll_bitmap ls7a2000;
+	struct ls7a1000_pixpll_bitmap ls7a1000;
+	struct ls2k1000_pixpll_bitmap ls2k1000;
+	struct ls2k0500_pixpll_bitmap ls2k0500;
+
+	u32 dword[4];
+};
+
+struct pixclk_to_pll_parm {
+	/* kHz */
+	unsigned int clock;
+
+	/* unrelated information */
+	unsigned short width;
+	unsigned short height;
+	unsigned short vrefresh;
+
+	/* Stores parameters for programming the Hardware PLLs */
+	unsigned short div_out;
+	unsigned short loopc;
+	unsigned short div_ref;
+};
+
+/*
+ * Pixel clock to PLL parameters translation table.
+ * Small static cached value to speed up PLL parameters calculation.
+ */
+static const struct pixclk_to_pll_parm pll_param_table[] = {
+	{148500, 1920, 1080, 60, 11, 49,  3},   /* 1920x1080@60Hz */
+						/* 1920x1080@50Hz */
+	{174500, 1920, 1080, 75, 17, 89,  3},   /* 1920x1080@75Hz */
+	{181250, 2560, 1080, 75,  8, 58,  4},   /* 2560x1080@75Hz */
+	{146250, 1680, 1050, 60, 16, 117, 5},   /* 1680x1050@60Hz */
+	{135000, 1280, 1024, 75, 10, 54,  4},   /* 1280x1024@75Hz */
+
+	{108000, 1600, 900,  60, 15, 81,  5},   /* 1600x900@60Hz  */
+						/* 1280x1024@60Hz */
+						/* 1280x960@60Hz */
+						/* 1152x864@75Hz */
+
+	{106500, 1440, 900,  60, 19, 81,  4},   /* 1440x900@60Hz */
+	{88750,  1440, 900,  60, 16, 71,  5},   /* 1440x900@60Hz */
+	{83500,  1280, 800,  60, 17, 71,  5},   /* 1280x800@60Hz */
+	{71000,  1280, 800,  60, 20, 71,  5},   /* 1280x800@60Hz */
+
+	{74250,  1280, 720,  60, 22, 49,  3},   /* 1280x720@60Hz */
+						/* 1280x720@50Hz */
+
+	{78750,  1024, 768,  75, 16, 63,  5},   /* 1024x768@75Hz */
+	{75000,  1024, 768,  70, 29, 87,  4},   /* 1024x768@70Hz */
+	{65000,  1024, 768,  60, 20, 39,  3},   /* 1024x768@60Hz */
+
+	{51200,  1024, 600,  60, 25, 64,  5},   /* 1024x600@60Hz */
+
+	{57284,  832,  624,  75, 24, 55,  4},   /* 832x624@75Hz */
+	{49500,  800,  600,  75, 40, 99,  5},   /* 800x600@75Hz */
+	{50000,  800,  600,  72, 44, 88,  4},   /* 800x600@72Hz */
+	{40000,  800,  600,  60, 30, 36,  3},   /* 800x600@60Hz */
+	{36000,  800,  600,  56, 50, 72,  4},   /* 800x600@56Hz */
+	{31500,  640,  480,  75, 40, 63,  5},   /* 640x480@75Hz */
+						/* 640x480@73Hz */
+
+	{30240,  640,  480,  67, 62, 75,  4},   /* 640x480@67Hz */
+	{27000,  720,  576,  50, 50, 54,  4},   /* 720x576@60Hz */
+	{25175,  640,  480,  60, 85, 107, 5},   /* 640x480@60Hz */
+	{25200,  640,  480,  60, 50, 63,  5},   /* 640x480@60Hz */
+						/* 720x480@60Hz */
+};
+
+/**
+ * lsdc_pixpll_setup - ioremap the device dependent PLL registers
+ *
+ * @this: point to the object which this function is called from
+ */
+static int lsdc_pixpll_setup(struct lsdc_pll * const this)
+{
+	this->mmio = ioremap(this->reg_base, this->reg_size);
+
+	return 0;
+}
+
+/*
+ * Find a set of pll parameters (to generate pixel clock) from a static
+ * local table, which avoid to compute the pll parameter eachtime a
+ * modeset is triggered.
+ *
+ * @this: point to the object which this function is called from
+ * @clock: the desired output pixel clock, the unit is kHz
+ * @pout: point to where the parameters to store if found
+ *
+ *  Return true if hit, otherwise return false.
+ */
+static bool lsdc_pixpll_find(struct lsdc_pll * const this,
+			     unsigned int clock,
+			     struct lsdc_pll_core_values * const pout)
+{
+	unsigned int num = ARRAY_SIZE(pll_param_table);
+	unsigned int i;
+
+	for (i = 0; i < num; i++) {
+		if (clock != pll_param_table[i].clock)
+			continue;
+
+		pout->div_ref = pll_param_table[i].div_ref;
+		pout->loopc   = pll_param_table[i].loopc;
+		pout->div_out = pll_param_table[i].div_out;
+
+		return true;
+	}
+
+	drm_dbg(this->ddev, "pixel clock %u: miss\n", clock);
+
+	return false;
+}
+
+/*
+ * Find a set of pll parameters which have minimal difference with the desired
+ * pixel clock frequency. It does that by computing all of the possible
+ * combination. Compute the diff and find the combination with minimal diff.
+ *
+ *  clock_out = refclk / div_ref * loopc / div_out
+ *
+ *  refclk is fixed as 100MHz in ls7a1000, ls2k1000 and ls2k0500
+ *
+ * @this: point to the object from which this function is called
+ * @clk: the desired output pixel clock, the unit is kHz
+ * @pout: point to where the parameters to store if success
+ *
+ *  Return true if a parameter is found, otherwise return false
+ */
+static bool lsdc_pixpll_compute(struct lsdc_pll * const this,
+				unsigned int clk,
+				struct lsdc_pll_core_values *pout)
+{
+	unsigned int refclk = this->ref_clock;
+	const unsigned int tolerance = 1000;
+	unsigned int min = tolerance;
+	unsigned int div_out, loopc, div_ref;
+
+	if (lsdc_pixpll_find(this, clk, pout))
+		return true;
+
+	for (div_out = 6; div_out < 64; div_out++) {
+		for (div_ref = 3; div_ref < 6; div_ref++) {
+			for (loopc = 6; loopc < 161; loopc++) {
+				int diff;
+
+				if (loopc < 12 * div_ref)
+					continue;
+				if (loopc > 32 * div_ref)
+					continue;
+
+				diff = clk * div_out - refclk * loopc / div_ref;
+
+				if (diff < 0)
+					diff = -diff;
+
+				if (diff < min) {
+					min = diff;
+					pout->div_ref = div_ref;
+					pout->div_out = div_out;
+					pout->loopc = loopc;
+
+					if (diff == 0)
+						return true;
+				}
+			}
+		}
+	}
+
+	return min < tolerance;
+}
+
+/*
+ * Update the pll parameters to hardware, target to the pixpll in ls7a1000
+ *
+ * @this: point to the object from which this function is called
+ * @param: point to the core parameters passed in
+ *
+ * return 0 if successful.
+ */
+static int ls7a1000_pixpll_param_update(struct lsdc_pll * const this,
+					struct lsdc_pll_core_values const *param)
+{
+	void __iomem *reg = this->mmio;
+	unsigned int counter = 0;
+	bool locked;
+	u32 val;
+
+	/* Bypass the software configured PLL, using refclk directly */
+	val = readl(reg + 0x4);
+	val &= ~(1 << 8);
+	writel(val, reg + 0x4);
+
+	/* Powerdown the PLL */
+	val = readl(reg + 0x4);
+	val |= (1 << 13);
+	writel(val, reg + 0x4);
+
+	/* Clear the pll parameters */
+	val = readl(reg + 0x4);
+	val &= ~(1 << 11);
+	writel(val, reg + 0x4);
+
+	/* clear old value & config new value */
+	val = readl(reg + 0x04);
+	val &= ~0x7F;
+	val |= param->div_ref;        /* div_ref */
+	writel(val, reg + 0x4);
+
+	val = readl(reg);
+	val &= ~0x7f;
+	val |= param->div_out;        /* div_out */
+
+	val &= ~(0x1ff << 21);
+	val |= param->loopc << 21;    /* loopc */
+	writel(val, reg);
+
+	/* Set the pll the parameters */
+	val = readl(reg + 0x4);
+	val |= (1 << 11);
+	writel(val, reg + 0x4);
+
+	/* Powerup the PLL */
+	val = readl(reg + 0x4);
+	val &= ~(1 << 13);
+	writel(val, reg + 0x4);
+
+	/* Wait the PLL lock */
+	do {
+		val = readl(reg + 0x4);
+		locked = val & 0x80;
+		counter++;
+	} while (!locked && (counter < 10000));
+
+	drm_dbg(this->ddev, "%u loop waited\n", counter);
+
+	/* Switch to the software configured pll */
+	val = readl(reg + 0x4);
+	val |= (1UL << 8);
+	writel(val, reg + 0x4);
+
+	return 0;
+}
+
+/*
+ * Update the pll parameters to hardware, target to the pixpll in ls2k1000
+ *
+ * @this: point to the object from which this function is called
+ * @param: pointer to where the parameter is passed in
+ *
+ * return 0 if successful.
+ */
+static int ls2k1000_pixpll_param_update(struct lsdc_pll * const this,
+					struct lsdc_pll_core_values const *param)
+{
+	void __iomem *reg = this->mmio;
+	unsigned int counter = 0;
+	bool locked = false;
+	u32 val;
+
+	val = readl(reg);
+	/* Bypass the software configured PLL, using refclk directly */
+	val &= ~(1 << 0);
+	writel(val, reg);
+
+	/* Powerdown the PLL */
+	val |= (1 << 19);
+	writel(val, reg);
+
+	/* Allow the software configuration */
+	val &= ~(1 << 2);
+	writel(val, reg);
+
+	/* allow L1 PLL lock */
+	val = (1L << 7) | (3L << 10);
+	writel(val, reg);
+
+	/* clear div_ref bit field */
+	val &= ~(0x3f << 26);
+	/* set div_ref bit field */
+	val = val | (param->div_ref << 26);
+	writel(val, reg);
+
+	val = readl(reg + 4);
+	/* clear loopc bit field */
+	val &= ~0x0fff;
+	/* set loopc bit field */
+	val |= param->loopc;
+	writel(val, reg + 4);
+
+	/* set div_out */
+	writel(param->div_out, reg + 8);
+
+	val = readl(reg);
+	/* use the software configure param */
+	val |= (1 << 2);
+	/* powerup the PLL */
+	val &= ~(1 << 19);
+	writel(val, reg);
+
+	/* wait pll setup and locked */
+	do {
+		val = readl(reg);
+		locked = val & 0x10000;
+		counter++;
+	} while (!locked && (counter < 10000));
+
+	drm_dbg(this->ddev, "%u loop waited\n", counter);
+
+	/* Switch to the above software configured PLL instead of refclk */
+	val |= 1;
+	writel(val, reg);
+
+	return 0;
+}
+
+/*
+ * Update the pll parameters to hardware, target to the pixpll in ls2k0500
+ *
+ * @this: point to the object which calling this function
+ * @param: pointer to where the parameters passed in
+ *
+ * return 0 if successful.
+ */
+static int ls2k0500_pixpll_param_update(struct lsdc_pll * const this,
+					struct lsdc_pll_core_values const *param)
+{
+	void __iomem *reg = this->mmio;
+	unsigned int counter = 0;
+	bool locked = false;
+	u32 val;
+
+	/* Bypass the software configured PLL, using refclk directly */
+	val = readl(reg);
+	val &= ~(1 << 0);
+	writel(val, reg);
+
+	/* Powerdown the PLL */
+	val = readl(reg);
+	val |= (1 << 5);
+	writel(val, reg);
+
+	/* Allow the software configuration */
+	val |= (1 << 3);
+	writel(val, reg);
+
+	/* Update the pll params */
+	val = (param->div_out << 24) |
+	      (param->loopc << 16) |
+	      (param->div_ref << 8);
+
+	writel(val, reg);
+
+	/* Powerup the PLL */
+	val = readl(reg);
+	val &= ~(1 << 5);
+	writel(val, reg);
+
+	/* wait pll setup and locked */
+	do {
+		val = readl(reg);
+		locked = val & 0x80;
+		counter++;
+	} while (!locked && (counter < 10000));
+
+	drm_dbg(this->ddev, "%u loop waited\n", counter);
+
+	/* Switch to the above software configured PLL instead of refclk */
+	writel((val | 1), reg);
+
+	return 0;
+}
+
+static unsigned int lsdc_get_clock_rate(struct lsdc_pll * const this,
+					struct lsdc_pll_core_values *pout)
+{
+	struct drm_device *ddev = this->ddev;
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	const struct lsdc_chip_desc * const desc = ldev->desc;
+	unsigned int out;
+	union lsdc_pixpll_bitmap parms;
+
+	if (desc->chip == LSDC_CHIP_7A2000) {
+		struct ls7a1000_pixpll_bitmap *obj = &parms.ls7a2000;
+
+		parms.dword[0] = readl(this->mmio);
+		parms.dword[1] = readl(this->mmio + 4);
+		out = this->ref_clock / obj->div_ref * obj->loopc / obj->div_out;
+		if (pout) {
+			pout->div_ref = obj->div_ref;
+			pout->loopc = obj->loopc;
+			pout->div_out = obj->div_out;
+		}
+	} else if (desc->chip == LSDC_CHIP_7A1000) {
+		struct ls7a1000_pixpll_bitmap *obj = &parms.ls7a1000;
+
+		parms.dword[0] = readl(this->mmio);
+		parms.dword[1] = readl(this->mmio + 4);
+		out = this->ref_clock / obj->div_ref * obj->loopc / obj->div_out;
+		if (pout) {
+			pout->div_ref = obj->div_ref;
+			pout->loopc = obj->loopc;
+			pout->div_out = obj->div_out;
+		}
+	} else if (desc->chip == LSDC_CHIP_2K1000) {
+		struct ls2k1000_pixpll_bitmap *obj = &parms.ls2k1000;
+
+		parms.dword[0] = readl(this->mmio);
+		parms.dword[1] = readl(this->mmio + 4);
+		parms.dword[2] = readl(this->mmio + 8);
+		parms.dword[3] = readl(this->mmio + 12);
+		out = this->ref_clock / obj->div_ref * obj->loopc / obj->div_out;
+		if (pout) {
+			pout->div_ref = obj->div_ref;
+			pout->loopc = obj->loopc;
+			pout->div_out = obj->div_out;
+		}
+	} else if (desc->chip == LSDC_CHIP_2K0500) {
+		struct ls2k0500_pixpll_bitmap *obj = &parms.ls2k0500;
+
+		parms.dword[0] = readl(this->mmio);
+		out = this->ref_clock / obj->div_ref * obj->loopc / obj->div_out;
+		if (pout) {
+			pout->div_ref = obj->div_ref;
+			pout->loopc = obj->loopc;
+			pout->div_out = obj->div_out;
+		}
+	} else {
+		drm_err(ddev, "unknown chip, the driver need update\n");
+		return 0;
+	}
+
+	return out;
+}
+
+static const struct lsdc_pixpll_funcs ls7a2000_pixpll_funcs = {
+	.setup = lsdc_pixpll_setup,
+	.compute = lsdc_pixpll_compute,
+	.update = ls7a1000_pixpll_param_update,
+	.get_clock_rate = lsdc_get_clock_rate,
+};
+
+static const struct lsdc_pixpll_funcs ls7a1000_pixpll_funcs = {
+	.setup = lsdc_pixpll_setup,
+	.compute = lsdc_pixpll_compute,
+	.update = ls7a1000_pixpll_param_update,
+	.get_clock_rate = lsdc_get_clock_rate,
+};
+
+static const struct lsdc_pixpll_funcs ls2k1000_pixpll_funcs = {
+	.setup = lsdc_pixpll_setup,
+	.compute = lsdc_pixpll_compute,
+	.update = ls2k1000_pixpll_param_update,
+	.get_clock_rate = lsdc_get_clock_rate,
+};
+
+static const struct lsdc_pixpll_funcs ls2k0500_pixpll_funcs = {
+	.setup = lsdc_pixpll_setup,
+	.compute = lsdc_pixpll_compute,
+	.update = ls2k0500_pixpll_param_update,
+	.get_clock_rate = lsdc_get_clock_rate,
+};
+
+int lsdc_pixpll_init(struct lsdc_pll * const this,
+		     struct drm_device *ddev,
+		     unsigned int index)
+{
+	struct lsdc_device *ldev = to_lsdc(ddev);
+	const struct lsdc_chip_desc * const descp = ldev->desc;
+
+	this->ddev = ddev;
+	this->index = index;
+	this->ref_clock = LSDC_PLL_REF_CLK;
+
+	if (descp->chip == LSDC_CHIP_7A2000) {
+		if (index == 0)
+			this->reg_base = LS7A1000_CFG_REG_BASE + LS7A1000_PIX_PLL0_REG;
+		else if (index == 1)
+			this->reg_base = LS7A1000_CFG_REG_BASE + LS7A1000_PIX_PLL1_REG;
+		this->reg_size = 8;
+		this->funcs = &ls7a2000_pixpll_funcs;
+	} else if (descp->chip == LSDC_CHIP_7A1000) {
+		if (index == 0)
+			this->reg_base = LS7A1000_CFG_REG_BASE + LS7A1000_PIX_PLL0_REG;
+		else if (index == 1)
+			this->reg_base = LS7A1000_CFG_REG_BASE + LS7A1000_PIX_PLL1_REG;
+		this->reg_size = 8;
+		this->funcs = &ls7a1000_pixpll_funcs;
+	} else if (descp->chip == LSDC_CHIP_2K1000) {
+		if (index == 0)
+			this->reg_base = LS2K1000_CFG_REG_BASE + LS2K1000_PIX_PLL0_REG;
+		else if (index == 1)
+			this->reg_base = LS2K1000_CFG_REG_BASE + LS2K1000_PIX_PLL1_REG;
+
+		this->reg_size = 16;
+		this->funcs = &ls2k1000_pixpll_funcs;
+	} else if (descp->chip == LSDC_CHIP_2K0500) {
+		if (index == 0)
+			this->reg_base = LS2K0500_CFG_REG_BASE + LS2K0500_PIX_PLL0_REG;
+		else if (index == 1)
+			this->reg_base = LS2K0500_CFG_REG_BASE + LS2K0500_PIX_PLL1_REG;
+
+		this->reg_size = 4;
+		this->funcs = &ls2k0500_pixpll_funcs;
+	} else {
+		drm_err(this->ddev, "unknown chip, the driver need update\n");
+		return -ENOENT;
+	}
+
+	return this->funcs->setup(this);
+}

drivers/gpu/drm/loongson/lsdc_pll.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2022 Loongson Corporation
+ */
+
+/*
+ * Authors:
+ *      Sui Jingfeng <suijingfeng@loongson.cn>
+ */
+
+#ifndef __LSDC_PLL_H__
+#define __LSDC_PLL_H__
+
+#include <drm/drm_device.h>
+
+/*
+ * PIXEL PLL hardware structure
+ *
+ * refclk: reference frequency, 100 MHz from external oscillator
+ * outclk: output frequency desired.
+ *
+ *
+ *               L1       Fref                      Fvco     L2
+ * refclk   +-----------+      +------------------+      +---------+   outclk
+ * ---+---> | Prescaler | ---> | Clock Multiplier | ---> | divider | -------->
+ *    |     +-----------+      +------------------+      +---------+     ^
+ *    |           ^                      ^                    ^          |
+ *    |           |                      |                    |          |
+ *    |           |                      |                    |          |
+ *    |        div_ref                 loopc               div_out       |
+ *    |                                                                  |
+ *    +---- sel_out (bypass above software configurable clock if==1) ----+
+ *
+ *  sel_out: PLL clock output selector.
+ *
+ *  If sel_out == 1, it will take refclk as output directly,
+ *  the L1 Prescaler and the out divider is bypassed.
+ *
+ *  If sel_out == 0, then:
+ *  outclk = refclk / div_ref * loopc / div_out;
+ *
+ * PLL hardware working requirements:
+ *
+ *  1) 20 MHz <= refclk / div_ref <= 40Mhz
+ *  2) 1.2 GHz <= refclk /div_out * loopc <= 3.2 Ghz
+ *
+ */
+
+struct lsdc_pll_core_values {
+	unsigned int div_ref;
+	unsigned int loopc;
+	unsigned int div_out;
+};
+
+struct lsdc_pll;
+
+struct lsdc_pixpll_funcs {
+	int (*setup)(struct lsdc_pll * const this);
+	bool (*compute)(struct lsdc_pll * const this, unsigned int clock,
+			struct lsdc_pll_core_values *params_out);
+	int (*update)(struct lsdc_pll * const this,
+		      struct lsdc_pll_core_values const *params_in);
+	unsigned int (*get_clock_rate)(struct lsdc_pll * const this,
+				       struct lsdc_pll_core_values *pout);
+};
+
+struct lsdc_pll {
+	const struct lsdc_pixpll_funcs *funcs;
+	struct drm_device *ddev;
+	void __iomem *mmio;
+
+	/* PLL register offset */
+	u32 reg_base;
+	/* PLL register size in bytes */
+	u32 reg_size;
+
+	/* 100000kHz, fixed on all board found */
+	unsigned int ref_clock;
+
+	unsigned int index;
+};
+
+int lsdc_pixpll_init(struct lsdc_pll * const this,
+		     struct drm_device *ddev,
+		     unsigned int index);
+
+#endif

drivers/gpu/drm/loongson/lsdc_regs.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2022 Loongson Corporation
+ */
+
+/*
+ * Authors:
+ *      Sui Jingfeng <suijingfeng@loongson.cn>
+ */
+
+#ifndef __LSDC_REGS_H__
+#define __LSDC_REGS_H__
+
+#include <linux/bitops.h>
+#include <linux/types.h>
+
+/*
+ * PIXEL PLL
+ */
+#define LSDC_PLL_REF_CLK                100000           /* kHz */
+
+/*
+ * Those PLL registers are not located at DC reg bar space,
+ * there are relative to LSXXXXX_CFG_REG_BASE.
+ * XXXXX = 7A1000, 2K1000, 2K0500
+ */
+
+/* LS2K1000 */
+#define LS2K1000_PIX_PLL0_REG           0x04B0
+#define LS2K1000_PIX_PLL1_REG           0x04C0
+#define LS2K1000_CFG_REG_BASE           0x1fe10000
+
+/* LS7A1000 */
+#define LS7A1000_PIX_PLL0_REG           0x04B0
+#define LS7A1000_PIX_PLL1_REG           0x04C0
+#define LS7A1000_CFG_REG_BASE           0x10010000
+
+/* LS2K0500 */
+#define LS2K0500_PIX_PLL0_REG           0x0418
+#define LS2K0500_PIX_PLL1_REG           0x0420
+#define LS2K0500_CFG_REG_BASE           0x1fe10000
+
+/*
+ *  CRTC CFG REG
+ */
+#define CFG_PIX_FMT_MASK                GENMASK(2, 0)
+
+enum lsdc_pixel_format {
+	LSDC_PF_NONE = 0,
+	LSDC_PF_ARGB4444 = 1,  /* ARGB A:4 bits R/G/B: 4 bits each [16 bits] */
+	LSDC_PF_ARGB1555 = 2,  /* ARGB A:1 bit RGB:15 bits [16 bits] */
+	LSDC_PF_RGB565 = 3,    /* RGB [16 bits] */
+	LSDC_PF_XRGB8888 = 4,  /* XRGB [32 bits] */
+};
+
+/* Each CRTC has two FB address registers, CFG_FB_IDX_BIT specify
+ * which fb address register is currently in using by the CRTC.
+ * Setting CFG_PAGE_FLIP_BIT bit will triger the switch. The switch
+ * finished at the vblank and if you want switch back you can set
+ * CFG_PAGE_FLIP_BIT again.
+ */
+#define CFG_PAGE_FLIP_BIT               BIT(7)
+#define CFG_OUTPUT_EN_BIT               BIT(8)
+/* CRTC0 clone from CRTC1 or CRTC1 clone from CRTC0 using hardware logic */
+#define CFG_PANEL_SWITCH                BIT(9)
+/* Indicate witch fb addr reg is in using, currently */
+#define CFG_FB_IDX_BIT                  BIT(11)
+#define CFG_GAMMAR_EN_BIT               BIT(12)
+
+/* CRTC get soft reset if voltage level change from 1 -> 0 */
+#define CFG_RESET_BIT                   BIT(20)
+
+#define EN_HSYNC_BIT                    BIT(30)
+#define INV_HSYNC_BIT                   BIT(31)
+#define EN_VSYNC_BIT                    BIT(30)
+#define INV_VSYNC_BIT                   BIT(31)
+
+/******** CRTC0 & DVO0 ********/
+#define LSDC_CRTC0_CFG_REG              0x1240
+#define LSDC_CRTC0_FB_ADDR0_REG         0x1260
+#define LSDC_CRTC0_FB_ADDR1_REG         0x1580
+#define LSDC_CRTC0_FB_HI_ADDR_REG       0x15A0
+#define LSDC_CRTC0_STRIDE_REG           0x1280
+#define LSDC_CRTC0_FB_ORIGIN_REG        0x1300
+#define LSDC_CRTC0_HDISPLAY_REG         0x1400
+#define LSDC_CRTC0_HSYNC_REG            0x1420
+#define LSDC_CRTC0_VDISPLAY_REG         0x1480
+#define LSDC_CRTC0_VSYNC_REG            0x14A0
+#define LSDC_CRTC0_GAMMA_INDEX_REG      0x14E0
+#define LSDC_CRTC0_GAMMA_DATA_REG       0x1500
+
+/******** CTRC1 & DVO1 ********/
+#define LSDC_CRTC1_CFG_REG              0x1250
+#define LSDC_CRTC1_FB_ADDR0_REG         0x1270
+#define LSDC_CRTC1_FB_ADDR1_REG         0x1590
+#define LSDC_CRTC1_FB_HI_ADDR_REG       0x15C0
+#define LSDC_CRTC1_STRIDE_REG           0x1290
+#define LSDC_CRTC1_FB_ORIGIN_REG        0x1310
+#define LSDC_CRTC1_HDISPLAY_REG         0x1410
+#define LSDC_CRTC1_HSYNC_REG            0x1430
+#define LSDC_CRTC1_VDISPLAY_REG         0x1490
+#define LSDC_CRTC1_VSYNC_REG            0x14B0
+#define LSDC_CRTC1_GAMMA_INDEX_REG      0x14F0
+#define LSDC_CRTC1_GAMMA_DATA_REG       0x1510
+
+#define LSDC_REGS_OFFSET                0x0010
+
+/*
+ * Hardware cursor
+ * There is only one hardware cursor shared by two CRTC in ls7a1000,
+ * ls2k1000 and ls2k0500.
+ */
+#define LSDC_CURSOR0_CFG_REG             0x1520
+#define LSDC_CURSOR0_ADDR_REG            0x1530
+#define LSDC_CURSOR0_POSITION_REG        0x1540
+#define LSDC_CURSOR0_BG_COLOR_REG        0x1550  /* background color */
+#define LSDC_CURSOR0_FG_COLOR_REG        0x1560  /* foreground color */
+
+#define LSDC_CURS_MIN_SIZE              1
+#define LSDC_CURS_MAX_SIZE              64
+#define CURSOR_FORMAT_MASK              GENMASK(1, 0)
+#define CURSOR_FORMAT_DISABLE           0
+#define CURSOR_FORMAT_MONOCHROME        1
+#define CURSOR_FORMAT_ARGB8888          2
+#define CURSOR_SIZE_64X64               BIT(2)
+#define CURSOR_LOCATION_BIT             BIT(4)
+
+/* LS7A2000 have two hardware cursor */
+
+#define LSDC_CURSOR1_CFG_REG            0x1670
+#define LSDC_CURSOR1_ADDR_REG           0x1680
+#define LSDC_CURSOR1_POSITION_REG       0x1690
+#define LSDC_CURSOR1_BG_COLOR_REG       0x16A0  /* background color */
+#define LSDC_CURSOR1_FG_COLOR_REG       0x16B0  /* foreground color */
+
+/*
+ * DC Interrupt Control Register, 32bit, Address Offset: 1570
+ *
+ * Bits  0:10 inidicate the interrupt type, read only
+ * Bits 16:26 control if the specific interrupt corresponding to bit 0~10
+ * is enabled or not. Write 1 to enable, write 0 to disable
+ *
+ * RF: Read Finished
+ * IDBU : Internal Data Buffer Underflow
+ * IDBFU : Internal Data Buffer Fatal Underflow
+ *
+ *
+ * +-------+-------------------------------+-------+--------+--------+-------+
+ * | 31:27 |            26:16              | 15:11 |   10   |   9    |   8   |
+ * +-------+-------------------------------+-------+--------+--------+-------+
+ * |  N/A  | Interrupt Enable Control Bits |  N/A  | IDBFU0 | IDBFU1 | IDBU0 |
+ * +-------+-------------------------------+-------+--------+--------+-------+
+ *
+ * Bit 4 is cursor buffer read finished, no use.
+ *
+ * +-------+-----+-----+-----+--------+--------+--------+--------+
+ * |   7   |  6  |  5  |  4  |   3    |   2    |   1    |   0    |
+ * +-------+-----+-----+-----+--------+--------+--------+--------+
+ * | IDBU1 | RF0 | RF1 |     | HSYNC0 | VSYNC0 | HSYNC1 | VSYNC1 |
+ * +-------+-----+-----+-----+--------+--------+--------+--------+
+ *
+ */
+
+#define LSDC_INT_REG                           0x1570
+
+#define INT_CRTC0_VS                           BIT(2)
+#define INT_CRTC0_HS                           BIT(3)
+#define INT_CRTC0_RF                           BIT(6)
+#define INT_CRTC0_IDBU                         BIT(8)
+#define INT_CRTC0_IDBFU                        BIT(10)
+
+#define INT_CURSOR_RF                          BIT(4)
+
+#define INT_CRTC1_VS                           BIT(0)
+#define INT_CRTC1_HS                           BIT(1)
+#define INT_CRTC1_RF                           BIT(5)
+#define INT_CRTC1_IDBU                         BIT(7)
+#define INT_CRTC1_IDBFU                        BIT(9)
+
+#define INT_CRTC0_VS_EN                        BIT(18)
+#define INT_CRTC0_HS_EN                        BIT(19)
+#define INT_CRTC0_RF_EN                        BIT(22)
+#define INT_CRTC0_IDBU_EN                      BIT(24)
+#define INT_CRTC0_IDBFU_EN                     BIT(26)
+
+#define INT_CURSOR_RF_EN                       BIT(20)
+
+#define INT_CRTC1_VS_EN                        BIT(16)
+#define INT_CRTC1_HS_EN                        BIT(17)
+#define INT_CRTC1_RF_EN                        BIT(21)
+#define INT_CRTC1_IDBU_EN                      BIT(23)
+#define INT_CRTC1_IDBFU_EN                     BIT(25)
+
+#define INT_STATUS_MASK                        GENMASK(10, 0)
+
+/*
+ * LS7A1000 have 4 gpios which is under control of the LS7A_DC_GPIO_DAT_REG
+ * and LS7A_DC_GPIO_DIR_REG register, it has no relationship whth the general
+ * GPIO hardware. Those registers are in the DC register space on LS7A1000.
+ *
+ * Those GPIOs are used to emulated I2C, for reading edid and monitor detection
+ *
+ * LS2k1000 and LS2K0500 don't have those registers, they use hardware i2c or
+ * generial GPIO emulated i2c from other module.
+ *
+ * GPIO data register
+ *  Address offset: 0x1650
+ *   +---------------+-----------+-----------+
+ *   | 7 | 6 | 5 | 4 |  3  |  2  |  1  |  0  |
+ *   +---------------+-----------+-----------+
+ *   |               |    DVO1   |    DVO0   |
+ *   +      N/A      +-----------+-----------+
+ *   |               | SCL | SDA | SCL | SDA |
+ *   +---------------+-----------+-----------+
+ */
+#define LS7A_DC_GPIO_DAT_REG                   0x1650
+
+/*
+ *  GPIO Input/Output direction control register
+ *  Address offset: 0x1660
+ *  write 1 for Input, 0 for Output.
+ */
+#define LS7A_DC_GPIO_DIR_REG                   0x1660
+
+/*
+ *  LS7A2000 Built-in HDMI Encoder
+ */
+#define HDMI_EN                 BIT(0)
+#define HDMI_PACKET_EN          BIT(1)
+
+#define HDMI0_ZONE_REG          0x1700
+#define HDMI1_ZONE_REG          0x1710
+
+#define HDMI0_CTRL_REG          0x1720
+#define HDMI1_CTRL_REG          0x1730
+
+#define HDMI_PLL_EN             BIT(0)
+#define HDMI_PLL_LOCKED         BIT(16)
+
+#define HDMI0_PHY_CTRL_REG      0x1800
+#define HDMI0_PLL_REG           0x1820
+
+#define HDMI1_PHY_CTRL_REG      0x1810
+#define HDMI1_PLL_REG           0x1830
+
+#define LS7A2000_DMA_STEP_MASK  GENMASK(17, 16)
+#define DMA_STEP_256_BYTE       (0 << 16)
+#define DMA_STEP_128_BYTE       (1 << 16)
+#define DMA_STEP_64_BYTE        (2 << 16)
+#define DMA_STEP_32_BYTE        (3 << 16)
+
+#endif