diff --git a/drivers/usb/gadget/net2280.h b/drivers/usb/gadget/net2280.h index e195abec8d7f5f5ca2b89b67f437cdf0dfec395c..957d6df3401509c7c3c6af1b31874cf5fadf50fa 100644 --- a/drivers/usb/gadget/net2280.h +++ b/drivers/usb/gadget/net2280.h @@ -22,422 +22,7 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ -/*-------------------------------------------------------------------------*/ - -/* NET2280 MEMORY MAPPED REGISTERS - * - * The register layout came from the chip documentation, and the bit - * number definitions were extracted from chip specification. - * - * Use the shift operator ('<<') to build bit masks, with readl/writel - * to access the registers through PCI. - */ - -/* main registers, BAR0 + 0x0000 */ -struct net2280_regs { - // offset 0x0000 - u32 devinit; -#define LOCAL_CLOCK_FREQUENCY 8 -#define FORCE_PCI_RESET 7 -#define PCI_ID 6 -#define PCI_ENABLE 5 -#define FIFO_SOFT_RESET 4 -#define CFG_SOFT_RESET 3 -#define PCI_SOFT_RESET 2 -#define USB_SOFT_RESET 1 -#define M8051_RESET 0 - u32 eectl; -#define EEPROM_ADDRESS_WIDTH 23 -#define EEPROM_CHIP_SELECT_ACTIVE 22 -#define EEPROM_PRESENT 21 -#define EEPROM_VALID 20 -#define EEPROM_BUSY 19 -#define EEPROM_CHIP_SELECT_ENABLE 18 -#define EEPROM_BYTE_READ_START 17 -#define EEPROM_BYTE_WRITE_START 16 -#define EEPROM_READ_DATA 8 -#define EEPROM_WRITE_DATA 0 - u32 eeclkfreq; - u32 _unused0; - // offset 0x0010 - - u32 pciirqenb0; /* interrupt PCI master ... */ -#define SETUP_PACKET_INTERRUPT_ENABLE 7 -#define ENDPOINT_F_INTERRUPT_ENABLE 6 -#define ENDPOINT_E_INTERRUPT_ENABLE 5 -#define ENDPOINT_D_INTERRUPT_ENABLE 4 -#define ENDPOINT_C_INTERRUPT_ENABLE 3 -#define ENDPOINT_B_INTERRUPT_ENABLE 2 -#define ENDPOINT_A_INTERRUPT_ENABLE 1 -#define ENDPOINT_0_INTERRUPT_ENABLE 0 - u32 pciirqenb1; -#define PCI_INTERRUPT_ENABLE 31 -#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27 -#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26 -#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25 -#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20 -#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19 -#define PCI_TARGET_ABORT_ASSERTED_INTERRUPT_ENABLE 18 -#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17 -#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16 -#define GPIO_INTERRUPT_ENABLE 13 -#define DMA_D_INTERRUPT_ENABLE 12 -#define DMA_C_INTERRUPT_ENABLE 11 -#define DMA_B_INTERRUPT_ENABLE 10 -#define DMA_A_INTERRUPT_ENABLE 9 -#define EEPROM_DONE_INTERRUPT_ENABLE 8 -#define VBUS_INTERRUPT_ENABLE 7 -#define CONTROL_STATUS_INTERRUPT_ENABLE 6 -#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4 -#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3 -#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2 -#define RESUME_INTERRUPT_ENABLE 1 -#define SOF_INTERRUPT_ENABLE 0 - u32 cpu_irqenb0; /* ... or onboard 8051 */ -#define SETUP_PACKET_INTERRUPT_ENABLE 7 -#define ENDPOINT_F_INTERRUPT_ENABLE 6 -#define ENDPOINT_E_INTERRUPT_ENABLE 5 -#define ENDPOINT_D_INTERRUPT_ENABLE 4 -#define ENDPOINT_C_INTERRUPT_ENABLE 3 -#define ENDPOINT_B_INTERRUPT_ENABLE 2 -#define ENDPOINT_A_INTERRUPT_ENABLE 1 -#define ENDPOINT_0_INTERRUPT_ENABLE 0 - u32 cpu_irqenb1; -#define CPU_INTERRUPT_ENABLE 31 -#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27 -#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26 -#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25 -#define PCI_INTA_INTERRUPT_ENABLE 24 -#define PCI_PME_INTERRUPT_ENABLE 23 -#define PCI_SERR_INTERRUPT_ENABLE 22 -#define PCI_PERR_INTERRUPT_ENABLE 21 -#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20 -#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19 -#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17 -#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16 -#define GPIO_INTERRUPT_ENABLE 13 -#define DMA_D_INTERRUPT_ENABLE 12 -#define DMA_C_INTERRUPT_ENABLE 11 -#define DMA_B_INTERRUPT_ENABLE 10 -#define DMA_A_INTERRUPT_ENABLE 9 -#define EEPROM_DONE_INTERRUPT_ENABLE 8 -#define VBUS_INTERRUPT_ENABLE 7 -#define CONTROL_STATUS_INTERRUPT_ENABLE 6 -#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4 -#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3 -#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2 -#define RESUME_INTERRUPT_ENABLE 1 -#define SOF_INTERRUPT_ENABLE 0 - - // offset 0x0020 - u32 _unused1; - u32 usbirqenb1; -#define USB_INTERRUPT_ENABLE 31 -#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27 -#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26 -#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25 -#define PCI_INTA_INTERRUPT_ENABLE 24 -#define PCI_PME_INTERRUPT_ENABLE 23 -#define PCI_SERR_INTERRUPT_ENABLE 22 -#define PCI_PERR_INTERRUPT_ENABLE 21 -#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20 -#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19 -#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17 -#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16 -#define GPIO_INTERRUPT_ENABLE 13 -#define DMA_D_INTERRUPT_ENABLE 12 -#define DMA_C_INTERRUPT_ENABLE 11 -#define DMA_B_INTERRUPT_ENABLE 10 -#define DMA_A_INTERRUPT_ENABLE 9 -#define EEPROM_DONE_INTERRUPT_ENABLE 8 -#define VBUS_INTERRUPT_ENABLE 7 -#define CONTROL_STATUS_INTERRUPT_ENABLE 6 -#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4 -#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3 -#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2 -#define RESUME_INTERRUPT_ENABLE 1 -#define SOF_INTERRUPT_ENABLE 0 - u32 irqstat0; -#define INTA_ASSERTED 12 -#define SETUP_PACKET_INTERRUPT 7 -#define ENDPOINT_F_INTERRUPT 6 -#define ENDPOINT_E_INTERRUPT 5 -#define ENDPOINT_D_INTERRUPT 4 -#define ENDPOINT_C_INTERRUPT 3 -#define ENDPOINT_B_INTERRUPT 2 -#define ENDPOINT_A_INTERRUPT 1 -#define ENDPOINT_0_INTERRUPT 0 - u32 irqstat1; -#define POWER_STATE_CHANGE_INTERRUPT 27 -#define PCI_ARBITER_TIMEOUT_INTERRUPT 26 -#define PCI_PARITY_ERROR_INTERRUPT 25 -#define PCI_INTA_INTERRUPT 24 -#define PCI_PME_INTERRUPT 23 -#define PCI_SERR_INTERRUPT 22 -#define PCI_PERR_INTERRUPT 21 -#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT 20 -#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT 19 -#define PCI_RETRY_ABORT_INTERRUPT 17 -#define PCI_MASTER_CYCLE_DONE_INTERRUPT 16 -#define SOF_DOWN_INTERRUPT 14 -#define GPIO_INTERRUPT 13 -#define DMA_D_INTERRUPT 12 -#define DMA_C_INTERRUPT 11 -#define DMA_B_INTERRUPT 10 -#define DMA_A_INTERRUPT 9 -#define EEPROM_DONE_INTERRUPT 8 -#define VBUS_INTERRUPT 7 -#define CONTROL_STATUS_INTERRUPT 6 -#define ROOT_PORT_RESET_INTERRUPT 4 -#define SUSPEND_REQUEST_INTERRUPT 3 -#define SUSPEND_REQUEST_CHANGE_INTERRUPT 2 -#define RESUME_INTERRUPT 1 -#define SOF_INTERRUPT 0 - // offset 0x0030 - u32 idxaddr; - u32 idxdata; - u32 fifoctl; -#define PCI_BASE2_RANGE 16 -#define IGNORE_FIFO_AVAILABILITY 3 -#define PCI_BASE2_SELECT 2 -#define FIFO_CONFIGURATION_SELECT 0 - u32 _unused2; - // offset 0x0040 - u32 memaddr; -#define START 28 -#define DIRECTION 27 -#define FIFO_DIAGNOSTIC_SELECT 24 -#define MEMORY_ADDRESS 0 - u32 memdata0; - u32 memdata1; - u32 _unused3; - // offset 0x0050 - u32 gpioctl; -#define GPIO3_LED_SELECT 12 -#define GPIO3_INTERRUPT_ENABLE 11 -#define GPIO2_INTERRUPT_ENABLE 10 -#define GPIO1_INTERRUPT_ENABLE 9 -#define GPIO0_INTERRUPT_ENABLE 8 -#define GPIO3_OUTPUT_ENABLE 7 -#define GPIO2_OUTPUT_ENABLE 6 -#define GPIO1_OUTPUT_ENABLE 5 -#define GPIO0_OUTPUT_ENABLE 4 -#define GPIO3_DATA 3 -#define GPIO2_DATA 2 -#define GPIO1_DATA 1 -#define GPIO0_DATA 0 - u32 gpiostat; -#define GPIO3_INTERRUPT 3 -#define GPIO2_INTERRUPT 2 -#define GPIO1_INTERRUPT 1 -#define GPIO0_INTERRUPT 0 -} __attribute__ ((packed)); - -/* usb control, BAR0 + 0x0080 */ -struct net2280_usb_regs { - // offset 0x0080 - u32 stdrsp; -#define STALL_UNSUPPORTED_REQUESTS 31 -#define SET_TEST_MODE 16 -#define GET_OTHER_SPEED_CONFIGURATION 15 -#define GET_DEVICE_QUALIFIER 14 -#define SET_ADDRESS 13 -#define ENDPOINT_SET_CLEAR_HALT 12 -#define DEVICE_SET_CLEAR_DEVICE_REMOTE_WAKEUP 11 -#define GET_STRING_DESCRIPTOR_2 10 -#define GET_STRING_DESCRIPTOR_1 9 -#define GET_STRING_DESCRIPTOR_0 8 -#define GET_SET_INTERFACE 6 -#define GET_SET_CONFIGURATION 5 -#define GET_CONFIGURATION_DESCRIPTOR 4 -#define GET_DEVICE_DESCRIPTOR 3 -#define GET_ENDPOINT_STATUS 2 -#define GET_INTERFACE_STATUS 1 -#define GET_DEVICE_STATUS 0 - u32 prodvendid; -#define PRODUCT_ID 16 -#define VENDOR_ID 0 - u32 relnum; - u32 usbctl; -#define SERIAL_NUMBER_INDEX 16 -#define PRODUCT_ID_STRING_ENABLE 13 -#define VENDOR_ID_STRING_ENABLE 12 -#define USB_ROOT_PORT_WAKEUP_ENABLE 11 -#define VBUS_PIN 10 -#define TIMED_DISCONNECT 9 -#define SUSPEND_IMMEDIATELY 7 -#define SELF_POWERED_USB_DEVICE 6 -#define REMOTE_WAKEUP_SUPPORT 5 -#define PME_POLARITY 4 -#define USB_DETECT_ENABLE 3 -#define PME_WAKEUP_ENABLE 2 -#define DEVICE_REMOTE_WAKEUP_ENABLE 1 -#define SELF_POWERED_STATUS 0 - // offset 0x0090 - u32 usbstat; -#define HIGH_SPEED 7 -#define FULL_SPEED 6 -#define GENERATE_RESUME 5 -#define GENERATE_DEVICE_REMOTE_WAKEUP 4 - u32 xcvrdiag; -#define FORCE_HIGH_SPEED_MODE 31 -#define FORCE_FULL_SPEED_MODE 30 -#define USB_TEST_MODE 24 -#define LINE_STATE 16 -#define TRANSCEIVER_OPERATION_MODE 2 -#define TRANSCEIVER_SELECT 1 -#define TERMINATION_SELECT 0 - u32 setup0123; - u32 setup4567; - // offset 0x0090 - u32 _unused0; - u32 ouraddr; -#define FORCE_IMMEDIATE 7 -#define OUR_USB_ADDRESS 0 - u32 ourconfig; -} __attribute__ ((packed)); - -/* pci control, BAR0 + 0x0100 */ -struct net2280_pci_regs { - // offset 0x0100 - u32 pcimstctl; -#define PCI_ARBITER_PARK_SELECT 13 -#define PCI_MULTI LEVEL_ARBITER 12 -#define PCI_RETRY_ABORT_ENABLE 11 -#define DMA_MEMORY_WRITE_AND_INVALIDATE_ENABLE 10 -#define DMA_READ_MULTIPLE_ENABLE 9 -#define DMA_READ_LINE_ENABLE 8 -#define PCI_MASTER_COMMAND_SELECT 6 -#define MEM_READ_OR_WRITE 0 -#define IO_READ_OR_WRITE 1 -#define CFG_READ_OR_WRITE 2 -#define PCI_MASTER_START 5 -#define PCI_MASTER_READ_WRITE 4 -#define PCI_MASTER_WRITE 0 -#define PCI_MASTER_READ 1 -#define PCI_MASTER_BYTE_WRITE_ENABLES 0 - u32 pcimstaddr; - u32 pcimstdata; - u32 pcimststat; -#define PCI_ARBITER_CLEAR 2 -#define PCI_EXTERNAL_ARBITER 1 -#define PCI_HOST_MODE 0 -} __attribute__ ((packed)); - -/* dma control, BAR0 + 0x0180 ... array of four structs like this, - * for channels 0..3. see also struct net2280_dma: descriptor - * that can be loaded into some of these registers. - */ -struct net2280_dma_regs { /* [11.7] */ - // offset 0x0180, 0x01a0, 0x01c0, 0x01e0, - u32 dmactl; -#define DMA_SCATTER_GATHER_DONE_INTERRUPT_ENABLE 25 -#define DMA_CLEAR_COUNT_ENABLE 21 -#define DESCRIPTOR_POLLING_RATE 19 -#define POLL_CONTINUOUS 0 -#define POLL_1_USEC 1 -#define POLL_100_USEC 2 -#define POLL_1_MSEC 3 -#define DMA_VALID_BIT_POLLING_ENABLE 18 -#define DMA_VALID_BIT_ENABLE 17 -#define DMA_SCATTER_GATHER_ENABLE 16 -#define DMA_OUT_AUTO_START_ENABLE 4 -#define DMA_PREEMPT_ENABLE 3 -#define DMA_FIFO_VALIDATE 2 -#define DMA_ENABLE 1 -#define DMA_ADDRESS_HOLD 0 - u32 dmastat; -#define DMA_ABORT_DONE_INTERRUPT 27 -#define DMA_SCATTER_GATHER_DONE_INTERRUPT 25 -#define DMA_TRANSACTION_DONE_INTERRUPT 24 -#define DMA_ABORT 1 -#define DMA_START 0 - u32 _unused0 [2]; - // offset 0x0190, 0x01b0, 0x01d0, 0x01f0, - u32 dmacount; -#define VALID_BIT 31 -#define DMA_DIRECTION 30 -#define DMA_DONE_INTERRUPT_ENABLE 29 -#define END_OF_CHAIN 28 -#define DMA_BYTE_COUNT_MASK ((1<<24)-1) -#define DMA_BYTE_COUNT 0 - u32 dmaaddr; - u32 dmadesc; - u32 _unused1; -} __attribute__ ((packed)); - -/* dedicated endpoint registers, BAR0 + 0x0200 */ - -struct net2280_dep_regs { /* [11.8] */ - // offset 0x0200, 0x0210, 0x220, 0x230, 0x240 - u32 dep_cfg; - // offset 0x0204, 0x0214, 0x224, 0x234, 0x244 - u32 dep_rsp; - u32 _unused [2]; -} __attribute__ ((packed)); - -/* configurable endpoint registers, BAR0 + 0x0300 ... array of seven structs - * like this, for ep0 then the configurable endpoints A..F - * ep0 reserved for control; E and F have only 64 bytes of fifo - */ -struct net2280_ep_regs { /* [11.9] */ - // offset 0x0300, 0x0320, 0x0340, 0x0360, 0x0380, 0x03a0, 0x03c0 - u32 ep_cfg; -#define ENDPOINT_BYTE_COUNT 16 -#define ENDPOINT_ENABLE 10 -#define ENDPOINT_TYPE 8 -#define ENDPOINT_DIRECTION 7 -#define ENDPOINT_NUMBER 0 - u32 ep_rsp; -#define SET_NAK_OUT_PACKETS 15 -#define SET_EP_HIDE_STATUS_PHASE 14 -#define SET_EP_FORCE_CRC_ERROR 13 -#define SET_INTERRUPT_MODE 12 -#define SET_CONTROL_STATUS_PHASE_HANDSHAKE 11 -#define SET_NAK_OUT_PACKETS_MODE 10 -#define SET_ENDPOINT_TOGGLE 9 -#define SET_ENDPOINT_HALT 8 -#define CLEAR_NAK_OUT_PACKETS 7 -#define CLEAR_EP_HIDE_STATUS_PHASE 6 -#define CLEAR_EP_FORCE_CRC_ERROR 5 -#define CLEAR_INTERRUPT_MODE 4 -#define CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE 3 -#define CLEAR_NAK_OUT_PACKETS_MODE 2 -#define CLEAR_ENDPOINT_TOGGLE 1 -#define CLEAR_ENDPOINT_HALT 0 - u32 ep_irqenb; -#define SHORT_PACKET_OUT_DONE_INTERRUPT_ENABLE 6 -#define SHORT_PACKET_TRANSFERRED_INTERRUPT_ENABLE 5 -#define DATA_PACKET_RECEIVED_INTERRUPT_ENABLE 3 -#define DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE 2 -#define DATA_OUT_PING_TOKEN_INTERRUPT_ENABLE 1 -#define DATA_IN_TOKEN_INTERRUPT_ENABLE 0 - u32 ep_stat; -#define FIFO_VALID_COUNT 24 -#define HIGH_BANDWIDTH_OUT_TRANSACTION_PID 22 -#define TIMEOUT 21 -#define USB_STALL_SENT 20 -#define USB_IN_NAK_SENT 19 -#define USB_IN_ACK_RCVD 18 -#define USB_OUT_PING_NAK_SENT 17 -#define USB_OUT_ACK_SENT 16 -#define FIFO_OVERFLOW 13 -#define FIFO_UNDERFLOW 12 -#define FIFO_FULL 11 -#define FIFO_EMPTY 10 -#define FIFO_FLUSH 9 -#define SHORT_PACKET_OUT_DONE_INTERRUPT 6 -#define SHORT_PACKET_TRANSFERRED_INTERRUPT 5 -#define NAK_OUT_PACKETS 4 -#define DATA_PACKET_RECEIVED_INTERRUPT 3 -#define DATA_PACKET_TRANSMITTED_INTERRUPT 2 -#define DATA_OUT_PING_TOKEN_INTERRUPT 1 -#define DATA_IN_TOKEN_INTERRUPT 0 - // offset 0x0310, 0x0330, 0x0350, 0x0370, 0x0390, 0x03b0, 0x03d0 - u32 ep_avail; - u32 ep_data; - u32 _unused0 [2]; -} __attribute__ ((packed)); +#include /*-------------------------------------------------------------------------*/ diff --git a/include/linux/usb/net2280.h b/include/linux/usb/net2280.h new file mode 100644 index 0000000000000000000000000000000000000000..c602f884f182ee91c7ce2a71fe77ab4071fb0edd --- /dev/null +++ b/include/linux/usb/net2280.h @@ -0,0 +1,444 @@ +/* + * NetChip 2280 high/full speed USB device controller. + * Unlike many such controllers, this one talks PCI. + */ +#ifndef __LINUX_USB_NET2280_H +#define __LINUX_USB_NET2280_H + +/* + * Copyright (C) 2002 NetChip Technology, Inc. (http://www.netchip.com) + * Copyright (C) 2003 David Brownell + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +/*-------------------------------------------------------------------------*/ + +/* NET2280 MEMORY MAPPED REGISTERS + * + * The register layout came from the chip documentation, and the bit + * number definitions were extracted from chip specification. + * + * Use the shift operator ('<<') to build bit masks, with readl/writel + * to access the registers through PCI. + */ + +/* main registers, BAR0 + 0x0000 */ +struct net2280_regs { + // offset 0x0000 + u32 devinit; +#define LOCAL_CLOCK_FREQUENCY 8 +#define FORCE_PCI_RESET 7 +#define PCI_ID 6 +#define PCI_ENABLE 5 +#define FIFO_SOFT_RESET 4 +#define CFG_SOFT_RESET 3 +#define PCI_SOFT_RESET 2 +#define USB_SOFT_RESET 1 +#define M8051_RESET 0 + u32 eectl; +#define EEPROM_ADDRESS_WIDTH 23 +#define EEPROM_CHIP_SELECT_ACTIVE 22 +#define EEPROM_PRESENT 21 +#define EEPROM_VALID 20 +#define EEPROM_BUSY 19 +#define EEPROM_CHIP_SELECT_ENABLE 18 +#define EEPROM_BYTE_READ_START 17 +#define EEPROM_BYTE_WRITE_START 16 +#define EEPROM_READ_DATA 8 +#define EEPROM_WRITE_DATA 0 + u32 eeclkfreq; + u32 _unused0; + // offset 0x0010 + + u32 pciirqenb0; /* interrupt PCI master ... */ +#define SETUP_PACKET_INTERRUPT_ENABLE 7 +#define ENDPOINT_F_INTERRUPT_ENABLE 6 +#define ENDPOINT_E_INTERRUPT_ENABLE 5 +#define ENDPOINT_D_INTERRUPT_ENABLE 4 +#define ENDPOINT_C_INTERRUPT_ENABLE 3 +#define ENDPOINT_B_INTERRUPT_ENABLE 2 +#define ENDPOINT_A_INTERRUPT_ENABLE 1 +#define ENDPOINT_0_INTERRUPT_ENABLE 0 + u32 pciirqenb1; +#define PCI_INTERRUPT_ENABLE 31 +#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27 +#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26 +#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25 +#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20 +#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19 +#define PCI_TARGET_ABORT_ASSERTED_INTERRUPT_ENABLE 18 +#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17 +#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16 +#define GPIO_INTERRUPT_ENABLE 13 +#define DMA_D_INTERRUPT_ENABLE 12 +#define DMA_C_INTERRUPT_ENABLE 11 +#define DMA_B_INTERRUPT_ENABLE 10 +#define DMA_A_INTERRUPT_ENABLE 9 +#define EEPROM_DONE_INTERRUPT_ENABLE 8 +#define VBUS_INTERRUPT_ENABLE 7 +#define CONTROL_STATUS_INTERRUPT_ENABLE 6 +#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4 +#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3 +#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2 +#define RESUME_INTERRUPT_ENABLE 1 +#define SOF_INTERRUPT_ENABLE 0 + u32 cpu_irqenb0; /* ... or onboard 8051 */ +#define SETUP_PACKET_INTERRUPT_ENABLE 7 +#define ENDPOINT_F_INTERRUPT_ENABLE 6 +#define ENDPOINT_E_INTERRUPT_ENABLE 5 +#define ENDPOINT_D_INTERRUPT_ENABLE 4 +#define ENDPOINT_C_INTERRUPT_ENABLE 3 +#define ENDPOINT_B_INTERRUPT_ENABLE 2 +#define ENDPOINT_A_INTERRUPT_ENABLE 1 +#define ENDPOINT_0_INTERRUPT_ENABLE 0 + u32 cpu_irqenb1; +#define CPU_INTERRUPT_ENABLE 31 +#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27 +#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26 +#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25 +#define PCI_INTA_INTERRUPT_ENABLE 24 +#define PCI_PME_INTERRUPT_ENABLE 23 +#define PCI_SERR_INTERRUPT_ENABLE 22 +#define PCI_PERR_INTERRUPT_ENABLE 21 +#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20 +#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19 +#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17 +#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16 +#define GPIO_INTERRUPT_ENABLE 13 +#define DMA_D_INTERRUPT_ENABLE 12 +#define DMA_C_INTERRUPT_ENABLE 11 +#define DMA_B_INTERRUPT_ENABLE 10 +#define DMA_A_INTERRUPT_ENABLE 9 +#define EEPROM_DONE_INTERRUPT_ENABLE 8 +#define VBUS_INTERRUPT_ENABLE 7 +#define CONTROL_STATUS_INTERRUPT_ENABLE 6 +#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4 +#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3 +#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2 +#define RESUME_INTERRUPT_ENABLE 1 +#define SOF_INTERRUPT_ENABLE 0 + + // offset 0x0020 + u32 _unused1; + u32 usbirqenb1; +#define USB_INTERRUPT_ENABLE 31 +#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27 +#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26 +#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25 +#define PCI_INTA_INTERRUPT_ENABLE 24 +#define PCI_PME_INTERRUPT_ENABLE 23 +#define PCI_SERR_INTERRUPT_ENABLE 22 +#define PCI_PERR_INTERRUPT_ENABLE 21 +#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20 +#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19 +#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17 +#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16 +#define GPIO_INTERRUPT_ENABLE 13 +#define DMA_D_INTERRUPT_ENABLE 12 +#define DMA_C_INTERRUPT_ENABLE 11 +#define DMA_B_INTERRUPT_ENABLE 10 +#define DMA_A_INTERRUPT_ENABLE 9 +#define EEPROM_DONE_INTERRUPT_ENABLE 8 +#define VBUS_INTERRUPT_ENABLE 7 +#define CONTROL_STATUS_INTERRUPT_ENABLE 6 +#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4 +#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3 +#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2 +#define RESUME_INTERRUPT_ENABLE 1 +#define SOF_INTERRUPT_ENABLE 0 + u32 irqstat0; +#define INTA_ASSERTED 12 +#define SETUP_PACKET_INTERRUPT 7 +#define ENDPOINT_F_INTERRUPT 6 +#define ENDPOINT_E_INTERRUPT 5 +#define ENDPOINT_D_INTERRUPT 4 +#define ENDPOINT_C_INTERRUPT 3 +#define ENDPOINT_B_INTERRUPT 2 +#define ENDPOINT_A_INTERRUPT 1 +#define ENDPOINT_0_INTERRUPT 0 + u32 irqstat1; +#define POWER_STATE_CHANGE_INTERRUPT 27 +#define PCI_ARBITER_TIMEOUT_INTERRUPT 26 +#define PCI_PARITY_ERROR_INTERRUPT 25 +#define PCI_INTA_INTERRUPT 24 +#define PCI_PME_INTERRUPT 23 +#define PCI_SERR_INTERRUPT 22 +#define PCI_PERR_INTERRUPT 21 +#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT 20 +#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT 19 +#define PCI_RETRY_ABORT_INTERRUPT 17 +#define PCI_MASTER_CYCLE_DONE_INTERRUPT 16 +#define SOF_DOWN_INTERRUPT 14 +#define GPIO_INTERRUPT 13 +#define DMA_D_INTERRUPT 12 +#define DMA_C_INTERRUPT 11 +#define DMA_B_INTERRUPT 10 +#define DMA_A_INTERRUPT 9 +#define EEPROM_DONE_INTERRUPT 8 +#define VBUS_INTERRUPT 7 +#define CONTROL_STATUS_INTERRUPT 6 +#define ROOT_PORT_RESET_INTERRUPT 4 +#define SUSPEND_REQUEST_INTERRUPT 3 +#define SUSPEND_REQUEST_CHANGE_INTERRUPT 2 +#define RESUME_INTERRUPT 1 +#define SOF_INTERRUPT 0 + // offset 0x0030 + u32 idxaddr; + u32 idxdata; + u32 fifoctl; +#define PCI_BASE2_RANGE 16 +#define IGNORE_FIFO_AVAILABILITY 3 +#define PCI_BASE2_SELECT 2 +#define FIFO_CONFIGURATION_SELECT 0 + u32 _unused2; + // offset 0x0040 + u32 memaddr; +#define START 28 +#define DIRECTION 27 +#define FIFO_DIAGNOSTIC_SELECT 24 +#define MEMORY_ADDRESS 0 + u32 memdata0; + u32 memdata1; + u32 _unused3; + // offset 0x0050 + u32 gpioctl; +#define GPIO3_LED_SELECT 12 +#define GPIO3_INTERRUPT_ENABLE 11 +#define GPIO2_INTERRUPT_ENABLE 10 +#define GPIO1_INTERRUPT_ENABLE 9 +#define GPIO0_INTERRUPT_ENABLE 8 +#define GPIO3_OUTPUT_ENABLE 7 +#define GPIO2_OUTPUT_ENABLE 6 +#define GPIO1_OUTPUT_ENABLE 5 +#define GPIO0_OUTPUT_ENABLE 4 +#define GPIO3_DATA 3 +#define GPIO2_DATA 2 +#define GPIO1_DATA 1 +#define GPIO0_DATA 0 + u32 gpiostat; +#define GPIO3_INTERRUPT 3 +#define GPIO2_INTERRUPT 2 +#define GPIO1_INTERRUPT 1 +#define GPIO0_INTERRUPT 0 +} __attribute__ ((packed)); + +/* usb control, BAR0 + 0x0080 */ +struct net2280_usb_regs { + // offset 0x0080 + u32 stdrsp; +#define STALL_UNSUPPORTED_REQUESTS 31 +#define SET_TEST_MODE 16 +#define GET_OTHER_SPEED_CONFIGURATION 15 +#define GET_DEVICE_QUALIFIER 14 +#define SET_ADDRESS 13 +#define ENDPOINT_SET_CLEAR_HALT 12 +#define DEVICE_SET_CLEAR_DEVICE_REMOTE_WAKEUP 11 +#define GET_STRING_DESCRIPTOR_2 10 +#define GET_STRING_DESCRIPTOR_1 9 +#define GET_STRING_DESCRIPTOR_0 8 +#define GET_SET_INTERFACE 6 +#define GET_SET_CONFIGURATION 5 +#define GET_CONFIGURATION_DESCRIPTOR 4 +#define GET_DEVICE_DESCRIPTOR 3 +#define GET_ENDPOINT_STATUS 2 +#define GET_INTERFACE_STATUS 1 +#define GET_DEVICE_STATUS 0 + u32 prodvendid; +#define PRODUCT_ID 16 +#define VENDOR_ID 0 + u32 relnum; + u32 usbctl; +#define SERIAL_NUMBER_INDEX 16 +#define PRODUCT_ID_STRING_ENABLE 13 +#define VENDOR_ID_STRING_ENABLE 12 +#define USB_ROOT_PORT_WAKEUP_ENABLE 11 +#define VBUS_PIN 10 +#define TIMED_DISCONNECT 9 +#define SUSPEND_IMMEDIATELY 7 +#define SELF_POWERED_USB_DEVICE 6 +#define REMOTE_WAKEUP_SUPPORT 5 +#define PME_POLARITY 4 +#define USB_DETECT_ENABLE 3 +#define PME_WAKEUP_ENABLE 2 +#define DEVICE_REMOTE_WAKEUP_ENABLE 1 +#define SELF_POWERED_STATUS 0 + // offset 0x0090 + u32 usbstat; +#define HIGH_SPEED 7 +#define FULL_SPEED 6 +#define GENERATE_RESUME 5 +#define GENERATE_DEVICE_REMOTE_WAKEUP 4 + u32 xcvrdiag; +#define FORCE_HIGH_SPEED_MODE 31 +#define FORCE_FULL_SPEED_MODE 30 +#define USB_TEST_MODE 24 +#define LINE_STATE 16 +#define TRANSCEIVER_OPERATION_MODE 2 +#define TRANSCEIVER_SELECT 1 +#define TERMINATION_SELECT 0 + u32 setup0123; + u32 setup4567; + // offset 0x0090 + u32 _unused0; + u32 ouraddr; +#define FORCE_IMMEDIATE 7 +#define OUR_USB_ADDRESS 0 + u32 ourconfig; +} __attribute__ ((packed)); + +/* pci control, BAR0 + 0x0100 */ +struct net2280_pci_regs { + // offset 0x0100 + u32 pcimstctl; +#define PCI_ARBITER_PARK_SELECT 13 +#define PCI_MULTI LEVEL_ARBITER 12 +#define PCI_RETRY_ABORT_ENABLE 11 +#define DMA_MEMORY_WRITE_AND_INVALIDATE_ENABLE 10 +#define DMA_READ_MULTIPLE_ENABLE 9 +#define DMA_READ_LINE_ENABLE 8 +#define PCI_MASTER_COMMAND_SELECT 6 +#define MEM_READ_OR_WRITE 0 +#define IO_READ_OR_WRITE 1 +#define CFG_READ_OR_WRITE 2 +#define PCI_MASTER_START 5 +#define PCI_MASTER_READ_WRITE 4 +#define PCI_MASTER_WRITE 0 +#define PCI_MASTER_READ 1 +#define PCI_MASTER_BYTE_WRITE_ENABLES 0 + u32 pcimstaddr; + u32 pcimstdata; + u32 pcimststat; +#define PCI_ARBITER_CLEAR 2 +#define PCI_EXTERNAL_ARBITER 1 +#define PCI_HOST_MODE 0 +} __attribute__ ((packed)); + +/* dma control, BAR0 + 0x0180 ... array of four structs like this, + * for channels 0..3. see also struct net2280_dma: descriptor + * that can be loaded into some of these registers. + */ +struct net2280_dma_regs { /* [11.7] */ + // offset 0x0180, 0x01a0, 0x01c0, 0x01e0, + u32 dmactl; +#define DMA_SCATTER_GATHER_DONE_INTERRUPT_ENABLE 25 +#define DMA_CLEAR_COUNT_ENABLE 21 +#define DESCRIPTOR_POLLING_RATE 19 +#define POLL_CONTINUOUS 0 +#define POLL_1_USEC 1 +#define POLL_100_USEC 2 +#define POLL_1_MSEC 3 +#define DMA_VALID_BIT_POLLING_ENABLE 18 +#define DMA_VALID_BIT_ENABLE 17 +#define DMA_SCATTER_GATHER_ENABLE 16 +#define DMA_OUT_AUTO_START_ENABLE 4 +#define DMA_PREEMPT_ENABLE 3 +#define DMA_FIFO_VALIDATE 2 +#define DMA_ENABLE 1 +#define DMA_ADDRESS_HOLD 0 + u32 dmastat; +#define DMA_ABORT_DONE_INTERRUPT 27 +#define DMA_SCATTER_GATHER_DONE_INTERRUPT 25 +#define DMA_TRANSACTION_DONE_INTERRUPT 24 +#define DMA_ABORT 1 +#define DMA_START 0 + u32 _unused0 [2]; + // offset 0x0190, 0x01b0, 0x01d0, 0x01f0, + u32 dmacount; +#define VALID_BIT 31 +#define DMA_DIRECTION 30 +#define DMA_DONE_INTERRUPT_ENABLE 29 +#define END_OF_CHAIN 28 +#define DMA_BYTE_COUNT_MASK ((1<<24)-1) +#define DMA_BYTE_COUNT 0 + u32 dmaaddr; + u32 dmadesc; + u32 _unused1; +} __attribute__ ((packed)); + +/* dedicated endpoint registers, BAR0 + 0x0200 */ + +struct net2280_dep_regs { /* [11.8] */ + // offset 0x0200, 0x0210, 0x220, 0x230, 0x240 + u32 dep_cfg; + // offset 0x0204, 0x0214, 0x224, 0x234, 0x244 + u32 dep_rsp; + u32 _unused [2]; +} __attribute__ ((packed)); + +/* configurable endpoint registers, BAR0 + 0x0300 ... array of seven structs + * like this, for ep0 then the configurable endpoints A..F + * ep0 reserved for control; E and F have only 64 bytes of fifo + */ +struct net2280_ep_regs { /* [11.9] */ + // offset 0x0300, 0x0320, 0x0340, 0x0360, 0x0380, 0x03a0, 0x03c0 + u32 ep_cfg; +#define ENDPOINT_BYTE_COUNT 16 +#define ENDPOINT_ENABLE 10 +#define ENDPOINT_TYPE 8 +#define ENDPOINT_DIRECTION 7 +#define ENDPOINT_NUMBER 0 + u32 ep_rsp; +#define SET_NAK_OUT_PACKETS 15 +#define SET_EP_HIDE_STATUS_PHASE 14 +#define SET_EP_FORCE_CRC_ERROR 13 +#define SET_INTERRUPT_MODE 12 +#define SET_CONTROL_STATUS_PHASE_HANDSHAKE 11 +#define SET_NAK_OUT_PACKETS_MODE 10 +#define SET_ENDPOINT_TOGGLE 9 +#define SET_ENDPOINT_HALT 8 +#define CLEAR_NAK_OUT_PACKETS 7 +#define CLEAR_EP_HIDE_STATUS_PHASE 6 +#define CLEAR_EP_FORCE_CRC_ERROR 5 +#define CLEAR_INTERRUPT_MODE 4 +#define CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE 3 +#define CLEAR_NAK_OUT_PACKETS_MODE 2 +#define CLEAR_ENDPOINT_TOGGLE 1 +#define CLEAR_ENDPOINT_HALT 0 + u32 ep_irqenb; +#define SHORT_PACKET_OUT_DONE_INTERRUPT_ENABLE 6 +#define SHORT_PACKET_TRANSFERRED_INTERRUPT_ENABLE 5 +#define DATA_PACKET_RECEIVED_INTERRUPT_ENABLE 3 +#define DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE 2 +#define DATA_OUT_PING_TOKEN_INTERRUPT_ENABLE 1 +#define DATA_IN_TOKEN_INTERRUPT_ENABLE 0 + u32 ep_stat; +#define FIFO_VALID_COUNT 24 +#define HIGH_BANDWIDTH_OUT_TRANSACTION_PID 22 +#define TIMEOUT 21 +#define USB_STALL_SENT 20 +#define USB_IN_NAK_SENT 19 +#define USB_IN_ACK_RCVD 18 +#define USB_OUT_PING_NAK_SENT 17 +#define USB_OUT_ACK_SENT 16 +#define FIFO_OVERFLOW 13 +#define FIFO_UNDERFLOW 12 +#define FIFO_FULL 11 +#define FIFO_EMPTY 10 +#define FIFO_FLUSH 9 +#define SHORT_PACKET_OUT_DONE_INTERRUPT 6 +#define SHORT_PACKET_TRANSFERRED_INTERRUPT 5 +#define NAK_OUT_PACKETS 4 +#define DATA_PACKET_RECEIVED_INTERRUPT 3 +#define DATA_PACKET_TRANSMITTED_INTERRUPT 2 +#define DATA_OUT_PING_TOKEN_INTERRUPT 1 +#define DATA_IN_TOKEN_INTERRUPT 0 + // offset 0x0310, 0x0330, 0x0350, 0x0370, 0x0390, 0x03b0, 0x03d0 + u32 ep_avail; + u32 ep_data; + u32 _unused0 [2]; +} __attribute__ ((packed)); + +#endif /* __LINUX_USB_NET2280_H */