rt2x00: Only disable beaconing just before beacon update

We should not write 0 to the beacon sync register during
config_intf() since that will clear out the beacon interval
and forces the beacon to be send out at the lowest interval.
(reported by Mattias Nissler).

The side effect of the same bug was that while working with
multiple virtual AP interfaces a change for any of those
interfaces would disable beaconing untill an beacon update
was provided.

This is resolved by only updating the TSF_SYNC value during
config_intf(). In update_beacon() we disable beaconing
temporarily to prevent fake beacons to be transmitted.
Finally kick_tx_queue() will enable beaconing again.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/rt2x00/rt2400pci.c

@@ -279,8 +279,6 @@ static void rt2400pci_config_intf(struct rt2x00_dev *rt2x00dev,
 	u32 reg;
 
 	if (flags & CONFIG_UPDATE_TYPE) {
-		rt2x00pci_register_write(rt2x00dev, CSR14, 0);
-
 		/*
 		 * Enable beacon config
 		 */
@@ -293,10 +291,6 @@ static void rt2400pci_config_intf(struct rt2x00_dev *rt2x00dev,
 		 * Enable synchronisation.
 		 */
 		rt2x00pci_register_read(rt2x00dev, CSR14, &reg);
-		rt2x00_set_field32(&reg, CSR14_TSF_COUNT, 1);
-		rt2x00_set_field32(&reg, CSR14_TBCN,
-				   (conf->sync == TSF_SYNC_BEACON));
-		rt2x00_set_field32(&reg, CSR14_BEACON_GEN, 0);
 		rt2x00_set_field32(&reg, CSR14_TSF_SYNC, conf->sync);
 		rt2x00pci_register_write(rt2x00dev, CSR14, reg);
 	}
@@ -1040,6 +1034,8 @@ static void rt2400pci_kick_tx_queue(struct rt2x00_dev *rt2x00dev,
 	if (queue == RT2X00_BCN_QUEUE_BEACON) {
 		rt2x00pci_register_read(rt2x00dev, CSR14, &reg);
 		if (!rt2x00_get_field32(reg, CSR14_BEACON_GEN)) {
+			rt2x00_set_field32(&reg, CSR14_TSF_COUNT, 1);
+			rt2x00_set_field32(&reg, CSR14_TBCN, 1);
 			rt2x00_set_field32(&reg, CSR14_BEACON_GEN, 1);
 			rt2x00pci_register_write(rt2x00dev, CSR14, reg);
 		}
@@ -1517,10 +1513,10 @@ static int rt2400pci_beacon_update(struct ieee80211_hw *hw, struct sk_buff *skb,
 	struct rt2x00_intf *intf = vif_to_intf(control->vif);
 	struct queue_entry_priv_pci_tx *priv_tx;
 	struct skb_frame_desc *skbdesc;
+	u32 reg;
 
 	if (unlikely(!intf->beacon))
 		return -ENOBUFS;
-
 	priv_tx = intf->beacon->priv_data;
 
 	/*
@@ -1535,6 +1531,16 @@ static int rt2400pci_beacon_update(struct ieee80211_hw *hw, struct sk_buff *skb,
 	skbdesc->desc_len = intf->beacon->queue->desc_size;
 	skbdesc->entry = intf->beacon;
 
+	/*
+	 * Disable beaconing while we are reloading the beacon data,
+	 * otherwise we might be sending out invalid data.
+	 */
+	rt2x00pci_register_read(rt2x00dev, CSR14, &reg);
+	rt2x00_set_field32(&reg, CSR14_TSF_COUNT, 0);
+	rt2x00_set_field32(&reg, CSR14_TBCN, 0);
+	rt2x00_set_field32(&reg, CSR14_BEACON_GEN, 0);
+	rt2x00pci_register_write(rt2x00dev, CSR14, reg);
+
 	/*
 	 * mac80211 doesn't provide the control->queue variable
 	 * for beacons. Set our own queue identification so

drivers/net/wireless/rt2x00/rt2500pci.c

@@ -281,8 +281,6 @@ static void rt2500pci_config_intf(struct rt2x00_dev *rt2x00dev,
 	u32 reg;
 
 	if (flags & CONFIG_UPDATE_TYPE) {
-		rt2x00pci_register_write(rt2x00dev, CSR14, 0);
-
 		/*
 		 * Enable beacon config
 		 */
@@ -296,10 +294,6 @@ static void rt2500pci_config_intf(struct rt2x00_dev *rt2x00dev,
 		 * Enable synchronisation.
 		 */
 		rt2x00pci_register_read(rt2x00dev, CSR14, &reg);
-		rt2x00_set_field32(&reg, CSR14_TSF_COUNT, 1);
-		rt2x00_set_field32(&reg, CSR14_TBCN,
-				   (conf->sync == TSF_SYNC_BEACON));
-		rt2x00_set_field32(&reg, CSR14_BEACON_GEN, 0);
 		rt2x00_set_field32(&reg, CSR14_TSF_SYNC, conf->sync);
 		rt2x00pci_register_write(rt2x00dev, CSR14, reg);
 	}
@@ -1193,6 +1187,8 @@ static void rt2500pci_kick_tx_queue(struct rt2x00_dev *rt2x00dev,
 	if (queue == RT2X00_BCN_QUEUE_BEACON) {
 		rt2x00pci_register_read(rt2x00dev, CSR14, &reg);
 		if (!rt2x00_get_field32(reg, CSR14_BEACON_GEN)) {
+			rt2x00_set_field32(&reg, CSR14_TSF_COUNT, 1);
+			rt2x00_set_field32(&reg, CSR14_TBCN, 1);
 			rt2x00_set_field32(&reg, CSR14_BEACON_GEN, 1);
 			rt2x00pci_register_write(rt2x00dev, CSR14, reg);
 		}
@@ -1828,6 +1824,7 @@ static int rt2500pci_beacon_update(struct ieee80211_hw *hw, struct sk_buff *skb,
 	struct rt2x00_intf *intf = vif_to_intf(control->vif);
 	struct queue_entry_priv_pci_tx *priv_tx;
 	struct skb_frame_desc *skbdesc;
+	u32 reg;
 
 	if (unlikely(!intf->beacon))
 		return -ENOBUFS;
@@ -1846,6 +1843,16 @@ static int rt2500pci_beacon_update(struct ieee80211_hw *hw, struct sk_buff *skb,
 	skbdesc->desc_len = intf->beacon->queue->desc_size;
 	skbdesc->entry = intf->beacon;
 
+	/*
+	 * Disable beaconing while we are reloading the beacon data,
+	 * otherwise we might be sending out invalid data.
+	 */
+	rt2x00pci_register_read(rt2x00dev, CSR14, &reg);
+	rt2x00_set_field32(&reg, CSR14_TSF_COUNT, 0);
+	rt2x00_set_field32(&reg, CSR14_TBCN, 0);
+	rt2x00_set_field32(&reg, CSR14_BEACON_GEN, 0);
+	rt2x00pci_register_write(rt2x00dev, CSR14, reg);
+
 	/*
 	 * mac80211 doesn't provide the control->queue variable
 	 * for beacons. Set our own queue identification so

drivers/net/wireless/rt2x00/rt2500usb.c

@@ -324,8 +324,6 @@ static void rt2500usb_config_intf(struct rt2x00_dev *rt2x00dev,
 	u16 reg;
 
 	if (flags & CONFIG_UPDATE_TYPE) {
-		rt2500usb_register_write(rt2x00dev, TXRX_CSR19, 0);
-
 		/*
 		 * Enable beacon config
 		 */
@@ -344,10 +342,6 @@ static void rt2500usb_config_intf(struct rt2x00_dev *rt2x00dev,
 		rt2500usb_register_write(rt2x00dev, TXRX_CSR18, reg);
 
 		rt2500usb_register_read(rt2x00dev, TXRX_CSR19, &reg);
-		rt2x00_set_field16(&reg, TXRX_CSR19_TSF_COUNT, 1);
-		rt2x00_set_field16(&reg, TXRX_CSR19_TBCN,
-				   (conf->sync == TSF_SYNC_BEACON));
-		rt2x00_set_field16(&reg, TXRX_CSR19_BEACON_GEN, 0);
 		rt2x00_set_field16(&reg, TXRX_CSR19_TSF_SYNC, conf->sync);
 		rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg);
 	}
@@ -1092,6 +1086,8 @@ static void rt2500usb_kick_tx_queue(struct rt2x00_dev *rt2x00dev,
 
 	rt2500usb_register_read(rt2x00dev, TXRX_CSR19, &reg);
 	if (!rt2x00_get_field16(reg, TXRX_CSR19_BEACON_GEN)) {
+		rt2x00_set_field16(&reg, TXRX_CSR19_TSF_COUNT, 1);
+		rt2x00_set_field16(&reg, TXRX_CSR19_TBCN, 1);
 		rt2x00_set_field16(&reg, TXRX_CSR19_BEACON_GEN, 1);
 		/*
 		 * Beacon generation will fail initially.
@@ -1740,6 +1736,7 @@ static int rt2500usb_beacon_update(struct ieee80211_hw *hw,
 	struct skb_frame_desc *skbdesc;
 	int pipe = usb_sndbulkpipe(usb_dev, 1);
 	int length;
+	u16 reg;
 
 	if (unlikely(!intf->beacon))
 		return -ENOBUFS;
@@ -1764,6 +1761,16 @@ static int rt2500usb_beacon_update(struct ieee80211_hw *hw,
 	skbdesc->desc_len = intf->beacon->queue->desc_size;
 	skbdesc->entry = intf->beacon;
 
+	/*
+	 * Disable beaconing while we are reloading the beacon data,
+	 * otherwise we might be sending out invalid data.
+	 */
+	rt2500usb_register_read(rt2x00dev, TXRX_CSR19, &reg);
+	rt2x00_set_field16(&reg, TXRX_CSR19_TSF_COUNT, 0);
+	rt2x00_set_field16(&reg, TXRX_CSR19_TBCN, 0);
+	rt2x00_set_field16(&reg, TXRX_CSR19_BEACON_GEN, 0);
+	rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg);
+
 	/*
 	 * mac80211 doesn't provide the control->queue variable
 	 * for beacons. Set our own queue identification so

drivers/net/wireless/rt2x00/rt61pci.c

@@ -336,17 +336,12 @@ static void rt61pci_config_intf(struct rt2x00_dev *rt2x00dev,
 		 * bits which (when set to 0) will invalidate the entire beacon.
 		 */
 		beacon_base = HW_BEACON_OFFSET(intf->beacon->entry_idx);
-		rt2x00pci_register_write(rt2x00dev, TXRX_CSR9, 0);
 		rt2x00pci_register_write(rt2x00dev, beacon_base, 0);
 
 		/*
 		 * Enable synchronisation.
 		 */
 		rt2x00pci_register_read(rt2x00dev, TXRX_CSR9, &reg);
-		rt2x00_set_field32(&reg, TXRX_CSR9_TSF_TICKING, 1);
-		rt2x00_set_field32(&reg, TXRX_CSR9_TBTT_ENABLE,
-				  (conf->sync == TSF_SYNC_BEACON));
-		rt2x00_set_field32(&reg, TXRX_CSR9_BEACON_GEN, 0);
 		rt2x00_set_field32(&reg, TXRX_CSR9_TSF_SYNC, conf->sync);
 		rt2x00pci_register_write(rt2x00dev, TXRX_CSR9, reg);
 	}
@@ -1562,6 +1557,8 @@ static void rt61pci_kick_tx_queue(struct rt2x00_dev *rt2x00dev,
 
 		rt2x00pci_register_read(rt2x00dev, TXRX_CSR9, &reg);
 		if (!rt2x00_get_field32(reg, TXRX_CSR9_BEACON_GEN)) {
+			rt2x00_set_field32(&reg, TXRX_CSR9_TSF_TICKING, 1);
+			rt2x00_set_field32(&reg, TXRX_CSR9_TBTT_ENABLE, 1);
 			rt2x00_set_field32(&reg, TXRX_CSR9_BEACON_GEN, 1);
 			rt2x00pci_register_write(rt2x00dev, TXRX_CSR9, reg);
 		}
@@ -2373,6 +2370,7 @@ static int rt61pci_beacon_update(struct ieee80211_hw *hw, struct sk_buff *skb,
 	struct rt2x00_intf *intf = vif_to_intf(control->vif);
 	struct skb_frame_desc *skbdesc;
 	unsigned int beacon_base;
+	u32 reg;
 
 	if (unlikely(!intf->beacon))
 		return -ENOBUFS;
@@ -2407,6 +2405,16 @@ static int rt61pci_beacon_update(struct ieee80211_hw *hw, struct sk_buff *skb,
 	skbdesc->desc_len = intf->beacon->queue->desc_size;
 	skbdesc->entry = intf->beacon;
 
+	/*
+	 * Disable beaconing while we are reloading the beacon data,
+	 * otherwise we might be sending out invalid data.
+	 */
+	rt2x00pci_register_read(rt2x00dev, TXRX_CSR9, &reg);
+	rt2x00_set_field32(&reg, TXRX_CSR9_TSF_TICKING, 0);
+	rt2x00_set_field32(&reg, TXRX_CSR9_TBTT_ENABLE, 0);
+	rt2x00_set_field32(&reg, TXRX_CSR9_BEACON_GEN, 0);
+	rt2x00pci_register_write(rt2x00dev, TXRX_CSR9, reg);
+
 	/*
 	 * mac80211 doesn't provide the control->queue variable
 	 * for beacons. Set our own queue identification so

drivers/net/wireless/rt2x00/rt73usb.c

@@ -347,17 +347,12 @@ static void rt73usb_config_intf(struct rt2x00_dev *rt2x00dev,
 		 * bits which (when set to 0) will invalidate the entire beacon.
 		 */
 		beacon_base = HW_BEACON_OFFSET(intf->beacon->entry_idx);
-		rt73usb_register_write(rt2x00dev, TXRX_CSR9, 0);
 		rt73usb_register_write(rt2x00dev, beacon_base, 0);
 
 		/*
 		 * Enable synchronisation.
 		 */
 		rt73usb_register_read(rt2x00dev, TXRX_CSR9, &reg);
-		rt2x00_set_field32(&reg, TXRX_CSR9_TSF_TICKING, 1);
-		rt2x00_set_field32(&reg, TXRX_CSR9_TBTT_ENABLE,
-				  (conf->sync == TSF_SYNC_BEACON));
-		rt2x00_set_field32(&reg, TXRX_CSR9_BEACON_GEN, 0);
 		rt2x00_set_field32(&reg, TXRX_CSR9_TSF_SYNC, conf->sync);
 		rt73usb_register_write(rt2x00dev, TXRX_CSR9, reg);
 	}
@@ -1312,6 +1307,8 @@ static void rt73usb_kick_tx_queue(struct rt2x00_dev *rt2x00dev,
 
 	rt73usb_register_read(rt2x00dev, TXRX_CSR9, &reg);
 	if (!rt2x00_get_field32(reg, TXRX_CSR9_BEACON_GEN)) {
+		rt2x00_set_field32(&reg, TXRX_CSR9_TSF_TICKING, 1);
+		rt2x00_set_field32(&reg, TXRX_CSR9_TBTT_ENABLE, 1);
 		rt2x00_set_field32(&reg, TXRX_CSR9_BEACON_GEN, 1);
 		rt73usb_register_write(rt2x00dev, TXRX_CSR9, reg);
 	}
@@ -1987,6 +1984,7 @@ static int rt73usb_beacon_update(struct ieee80211_hw *hw, struct sk_buff *skb,
 	struct skb_frame_desc *skbdesc;
 	unsigned int beacon_base;
 	unsigned int timeout;
+	u32 reg;
 
 	if (unlikely(!intf->beacon))
 		return -ENOBUFS;
@@ -2009,6 +2007,16 @@ static int rt73usb_beacon_update(struct ieee80211_hw *hw, struct sk_buff *skb,
 	skbdesc->desc_len = intf->beacon->queue->desc_size;
 	skbdesc->entry = intf->beacon;
 
+	/*
+	 * Disable beaconing while we are reloading the beacon data,
+	 * otherwise we might be sending out invalid data.
+	 */
+	rt73usb_register_read(rt2x00dev, TXRX_CSR9, &reg);
+	rt2x00_set_field32(&reg, TXRX_CSR9_TSF_TICKING, 0);
+	rt2x00_set_field32(&reg, TXRX_CSR9_TBTT_ENABLE, 0);
+	rt2x00_set_field32(&reg, TXRX_CSR9_BEACON_GEN, 0);
+	rt73usb_register_write(rt2x00dev, TXRX_CSR9, reg);
+
 	/*
 	 * mac80211 doesn't provide the control->queue variable
 	 * for beacons. Set our own queue identification so