Staging: ipack/devices/ipoctal: remove ipoctal_config structure.

The configuration of the communication channel is handled by the tty
abstraction, so the ipoctal_config structure has become useless and it's
only used to store values that are never accesed. Remove it.
Signed-off-by: NMiguel Gómez <magomez@igalia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/staging/ipack/devices/ipoctal.c

@@ -49,7 +49,6 @@ struct ipoctal {
 	char				*buffer[NR_CHANNELS];
 	unsigned int			nb_bytes[NR_CHANNELS];
 	unsigned int			count_wr[NR_CHANNELS];
-	struct ipoctal_config		chan_config[NR_CHANNELS];
 	wait_queue_head_t		queue[NR_CHANNELS];
 	unsigned short			error_flag[NR_CHANNELS];
 	spinlock_t			lock[NR_CHANNELS];
@@ -671,22 +670,18 @@ static void ipoctal_set_termios(struct tty_struct *tty,
 		if (cflag & CRTSCTS) {
 			mr1 |= MR1_RxRTS_CONTROL_ON;
 			mr2 |= MR2_TxRTS_CONTROL_OFF | MR2_CTS_ENABLE_TX_ON;
-			ipoctal->chan_config[channel].flow_control = 1;
 		} else {
 			mr1 |= MR1_RxRTS_CONTROL_OFF;
 			mr2 |= MR2_TxRTS_CONTROL_OFF | MR2_CTS_ENABLE_TX_OFF;
-			ipoctal->chan_config[channel].flow_control = 0;
 		}
 		break;
 	case IP_OCTAL_422_ID:
 		mr1 |= MR1_RxRTS_CONTROL_OFF;
 		mr2 |= MR2_TxRTS_CONTROL_OFF | MR2_CTS_ENABLE_TX_OFF;
-		ipoctal->chan_config[channel].flow_control = 0;
 		break;
 	case IP_OCTAL_485_ID:
 		mr1 |= MR1_RxRTS_CONTROL_OFF;
 		mr2 |= MR2_TxRTS_CONTROL_ON | MR2_CTS_ENABLE_TX_OFF;
-		ipoctal->chan_config[channel].flow_control = 0;
 		break;
 	default:
 		return;
@@ -750,12 +745,6 @@ static void ipoctal_set_termios(struct tty_struct *tty,
 	ipoctal_write_io_reg(ipoctal, &ipoctal->chan_regs[channel].u.w.mr, mr2);
 	ipoctal_write_io_reg(ipoctal, &ipoctal->chan_regs[channel].u.w.csr, csr);
 
-	/* save the setup in the structure */
-	ipoctal->chan_config[channel].baud = tty_get_baud_rate(tty);
-	ipoctal->chan_config[channel].bits_per_char = cflag & CSIZE;
-	ipoctal->chan_config[channel].parity = cflag & PARENB;
-	ipoctal->chan_config[channel].stop_bits = cflag & CSTOPB;
-
 	/* Enable again the RX */
 	ipoctal_write_io_reg(ipoctal, &ipoctal->chan_regs[channel].u.w.cr,
 			     CR_ENABLE_RX);

drivers/staging/ipack/devices/ipoctal.h

@@ -41,23 +41,6 @@ enum uart_error	{
 	UART_BREAK   = 1 << 4, /* Received break */
 };
 
-/**
- * struct ipoctal_config - Serial configuration
- *
- * @baud: Baud rate
- * @stop_bits: Stop bits (1 or 2)
- * @bits_per_char: data size in bits
- * @parity
- * @flow_control: Flow control management (RTS/CTS) (0 disabled, 1 enabled)
- */
-struct ipoctal_config {
-	unsigned int baud;
-	unsigned int stop_bits;
-	unsigned int bits_per_char;
-	unsigned short parity;
-	unsigned int flow_control;
-};
-
 /**
  * struct ipoctal_stats -- Stats since last reset
  *