From 850a5b670af6293fcb1852af57567d19150ff638 Mon Sep 17 00:00:00 2001
From: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Date: Fri, 23 Nov 2012 13:44:39 +0100
Subject: [PATCH] spi/atmel: add DT support

Use the newly introduce cs-gpios dt support on atmel.
We do not use the hardware cs as it's wired and has bugs and limitations.
As the controller believes that only active-low devices/systems exists.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
---
 .../devicetree/bindings/spi/spi_atmel.txt     | 26 +++++++++++++++++++
 drivers/spi/spi-atmel.c                       | 17 +++++++++++-
 2 files changed, 42 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/spi/spi_atmel.txt

diff --git a/Documentation/devicetree/bindings/spi/spi_atmel.txt b/Documentation/devicetree/bindings/spi/spi_atmel.txt
new file mode 100644
index 000000000000..07e04cdc0c9e
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi_atmel.txt
@@ -0,0 +1,26 @@
+Atmel SPI device
+
+Required properties:
+- compatible : should be "atmel,at91rm9200-spi".
+- reg: Address and length of the register set for the device
+- interrupts: Should contain spi interrupt
+- cs-gpios: chipselects
+
+Example:
+
+spi1: spi@fffcc000 {
+	compatible = "atmel,at91rm9200-spi";
+	reg = <0xfffcc000 0x4000>;
+	interrupts = <13 4 5>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cs-gpios = <&pioB 3 0>;
+	status = "okay";
+
+	mmc-slot@0 {
+		compatible = "mmc-spi-slot";
+		reg = <0>;
+		gpios = <&pioC 4 0>;	/* CD */
+		spi-max-frequency = <25000000>;
+	};
+};
diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c
index 75c0c4f5fdf2..ab34497bcfee 100644
--- a/drivers/spi/spi-atmel.c
+++ b/drivers/spi/spi-atmel.c
@@ -20,6 +20,7 @@
 #include <linux/spi/spi.h>
 #include <linux/slab.h>
 #include <linux/platform_data/atmel.h>
+#include <linux/of.h>
 
 #include <asm/io.h>
 #include <asm/gpio.h>
@@ -768,6 +769,10 @@ static int atmel_spi_setup(struct spi_device *spi)
 
 	/* chipselect must have been muxed as GPIO (e.g. in board setup) */
 	npcs_pin = (unsigned int)spi->controller_data;
+
+	if (gpio_is_valid(spi->cs_gpio))
+		npcs_pin = spi->cs_gpio;
+
 	asd = spi->controller_state;
 	if (!asd) {
 		asd = kzalloc(sizeof(struct atmel_spi_device), GFP_KERNEL);
@@ -937,8 +942,9 @@ static int atmel_spi_probe(struct platform_device *pdev)
 	/* the spi->mode bits understood by this driver: */
 	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
 
+	master->dev.of_node = pdev->dev.of_node;
 	master->bus_num = pdev->id;
-	master->num_chipselect = 4;
+	master->num_chipselect = master->dev.of_node ? 0 : 4;
 	master->setup = atmel_spi_setup;
 	master->transfer = atmel_spi_transfer;
 	master->cleanup = atmel_spi_cleanup;
@@ -1064,11 +1070,20 @@ static int atmel_spi_resume(struct platform_device *pdev)
 #define	atmel_spi_resume	NULL
 #endif
 
+#if defined(CONFIG_OF)
+static const struct of_device_id atmel_spi_dt_ids[] = {
+	{ .compatible = "atmel,at91rm9200-spi" },
+	{ /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(of, atmel_spi_dt_ids);
+#endif
 
 static struct platform_driver atmel_spi_driver = {
 	.driver		= {
 		.name	= "atmel_spi",
 		.owner	= THIS_MODULE,
+		.of_match_table	= of_match_ptr(atmel_spi_dt_ids),
 	},
 	.suspend	= atmel_spi_suspend,
 	.resume		= atmel_spi_resume,
-- 
GitLab