extcon: usbc-tusb320: Add support for mode setting and reset

Reset the chip and set its mode to default (maintain mode set by PORT pin)
during probe to make sure it comes up in the default state.
Signed-off-by: NYassine Oudjana <y.oudjana@protonmail.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>

drivers/extcon/extcon-usbc-tusb320.c

@@ -19,15 +19,32 @@
 #define TUSB320_REG9_ATTACHED_STATE_MASK	0x3
 #define TUSB320_REG9_CABLE_DIRECTION		BIT(5)
 #define TUSB320_REG9_INTERRUPT_STATUS		BIT(4)
-#define TUSB320_ATTACHED_STATE_NONE		0x0
-#define TUSB320_ATTACHED_STATE_DFP		0x1
-#define TUSB320_ATTACHED_STATE_UFP		0x2
-#define TUSB320_ATTACHED_STATE_ACC		0x3
+
+#define TUSB320_REGA				0xa
+#define TUSB320_REGA_I2C_SOFT_RESET		BIT(3)
+#define TUSB320_REGA_MODE_SELECT_SHIFT		4
+#define TUSB320_REGA_MODE_SELECT_MASK		0x3
+
+enum tusb320_attached_state {
+	TUSB320_ATTACHED_STATE_NONE,
+	TUSB320_ATTACHED_STATE_DFP,
+	TUSB320_ATTACHED_STATE_UFP,
+	TUSB320_ATTACHED_STATE_ACC,
+};
+
+enum tusb320_mode {
+	TUSB320_MODE_PORT,
+	TUSB320_MODE_UFP,
+	TUSB320_MODE_DFP,
+	TUSB320_MODE_DRP,
+};
 
 struct tusb320_priv {
 	struct device *dev;
 	struct regmap *regmap;
 	struct extcon_dev *edev;
+
+	enum tusb320_attached_state state;
 };
 
 static const char * const tusb_attached_states[] = {
@@ -62,6 +79,53 @@ static int tusb320_check_signature(struct tusb320_priv *priv)
 	return 0;
 }
 
+static int tusb320_set_mode(struct tusb320_priv *priv, enum tusb320_mode mode)
+{
+	int ret;
+
+	/* Mode cannot be changed while cable is attached */
+	if (priv->state != TUSB320_ATTACHED_STATE_NONE)
+		return -EBUSY;
+
+	/* Write mode */
+	ret = regmap_write_bits(priv->regmap, TUSB320_REGA,
+		TUSB320_REGA_MODE_SELECT_MASK << TUSB320_REGA_MODE_SELECT_SHIFT,
+		mode << TUSB320_REGA_MODE_SELECT_SHIFT);
+	if (ret) {
+		dev_err(priv->dev, "failed to write mode: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int tusb320_reset(struct tusb320_priv *priv)
+{
+	int ret;
+
+	/* Set mode to default (follow PORT pin) */
+	ret = tusb320_set_mode(priv, TUSB320_MODE_PORT);
+	if (ret && ret != -EBUSY) {
+		dev_err(priv->dev,
+			"failed to set mode to PORT: %d\n", ret);
+		return ret;
+	}
+
+	/* Perform soft reset */
+	ret = regmap_write_bits(priv->regmap, TUSB320_REGA,
+			TUSB320_REGA_I2C_SOFT_RESET, 1);
+	if (ret) {
+		dev_err(priv->dev,
+			"failed to write soft reset bit: %d\n", ret);
+		return ret;
+	}
+
+	/* Wait for chip to go through reset */
+	msleep(95);
+
+	return 0;
+}
+
 static irqreturn_t tusb320_irq_handler(int irq, void *dev_id)
 {
 	struct tusb320_priv *priv = dev_id;
@@ -96,6 +160,8 @@ static irqreturn_t tusb320_irq_handler(int irq, void *dev_id)
 	extcon_sync(priv->edev, EXTCON_USB);
 	extcon_sync(priv->edev, EXTCON_USB_HOST);
 
+	priv->state = state;
+
 	regmap_write(priv->regmap, TUSB320_REG9, reg);
 
 	return IRQ_HANDLED;
@@ -145,6 +211,17 @@ static int tusb320_extcon_probe(struct i2c_client *client,
 	/* update initial state */
 	tusb320_irq_handler(client->irq, priv);
 
+	/* Reset chip to its default state */
+	ret = tusb320_reset(priv);
+	if (ret)
+		dev_warn(priv->dev, "failed to reset chip: %d\n", ret);
+	else
+		/*
+		 * State and polarity might change after a reset, so update
+		 * them again and make sure the interrupt status bit is cleared.
+		 */
+		tusb320_irq_handler(client->irq, priv);
+
 	ret = devm_request_threaded_irq(priv->dev, client->irq, NULL,
 					tusb320_irq_handler,
 					IRQF_TRIGGER_FALLING | IRQF_ONESHOT,