提交 6c4ba00c 编写于 作者: L Linus Torvalds

Merge tag 'hsi-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi

Pull HSI updates from Sebastian Reichel:

 - add HSI OMAP4 bindings

 - misc small fixes

* tag 'hsi-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi:
  dt-bindings: hsi: add omap4 hsi controller bindings
  HSI: hsi_char: pr_err() strings should end with newlines
  HSI: omap_ssi_core: fix kilo to be "k" not "K"
OMAP SSI controller bindings
OMAP Synchronous Serial Interface (SSI) controller implements a legacy
variant of MIPI's High Speed Synchronous Serial Interface (HSI).
OMAP3's Synchronous Serial Interface (SSI) controller implements a
legacy variant of MIPI's High Speed Synchronous Serial Interface (HSI),
while the controller found inside OMAP4 is supposed to be fully compliant
with the HSI standard.
Required properties:
- compatible: Should include "ti,omap3-ssi".
- compatible: Should include "ti,omap3-ssi" or "ti,omap4-hsi"
- reg-names: Contains the values "sys" and "gdd" (in this order).
- reg: Contains a matching register specifier for each entry
in reg-names.
......@@ -27,6 +29,7 @@ Each port is represented as a sub-node of the ti,omap3-ssi device.
Required Port sub-node properties:
- compatible: Should be set to the following value
ti,omap3-ssi-port (applicable to OMAP34xx devices)
ti,omap4-hsi-port (applicable to OMAP44xx devices)
- reg-names: Contains the values "tx" and "rx" (in this order).
- reg: Contains a matching register specifier for each entry
in reg-names.
......@@ -38,6 +41,10 @@ Required Port sub-node properties:
property. If it's missing the port will not be
enabled.
Optional properties:
- ti,hwmods: Shall contain TI interconnect module name if needed
by the SoC
Example for Nokia N900:
ssi-controller@48058000 {
......
......@@ -773,13 +773,13 @@ static int __init hsc_init(void)
if ((max_data_size < 4) || (max_data_size > 0x10000) ||
(max_data_size & (max_data_size - 1))) {
pr_err("Invalid max read/write data size");
pr_err("Invalid max read/write data size\n");
return -EINVAL;
}
ret = hsi_register_client_driver(&hsc_driver);
if (ret) {
pr_err("Error while registering HSI/SSI driver %d", ret);
pr_err("Error while registering HSI/SSI driver %d\n", ret);
return ret;
}
......
......@@ -334,7 +334,7 @@ static int ssi_clk_event(struct notifier_block *nb, unsigned long event,
case POST_RATE_CHANGE:
dev_dbg(&ssi->device, "post rate change (%lu -> %lu)\n",
clk_data->old_rate, clk_data->new_rate);
omap_ssi->fck_rate = DIV_ROUND_CLOSEST(clk_data->new_rate, 1000); /* KHz */
omap_ssi->fck_rate = DIV_ROUND_CLOSEST(clk_data->new_rate, 1000); /* kHz */
for (i = 0; i < ssi->num_ports; i++) {
omap_port = omap_ssi->port[i];
......@@ -467,9 +467,9 @@ static int ssi_hw_init(struct hsi_controller *ssi)
}
/* Resetting GDD */
writel_relaxed(SSI_SWRESET, omap_ssi->gdd + SSI_GDD_GRST_REG);
/* Get FCK rate in KHz */
/* Get FCK rate in kHz */
omap_ssi->fck_rate = DIV_ROUND_CLOSEST(ssi_get_clk_rate(ssi), 1000);
dev_dbg(&ssi->device, "SSI fck rate %lu KHz\n", omap_ssi->fck_rate);
dev_dbg(&ssi->device, "SSI fck rate %lu kHz\n", omap_ssi->fck_rate);
writel_relaxed(SSI_CLK_AUTOGATING_ON, omap_ssi->sys + SSI_GDD_GCR_REG);
omap_ssi->gdd_gcr = SSI_CLK_AUTOGATING_ON;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册