rt2x00: Only configure hardware when radio is enabled

Some hardware configuration registers such as antenna and channel configuration
can only be written when the radio is enabled. Previously, we didn't consider
this, so some configuration items could be set inconsistently after reenabling
the radio. This patch changes the config() handler to only reprogram the
hardware when the radio is enabled. Configuration changes that are made while
the radio is off are postponed until the radio is switched back on. We also
leave the radio turned off during initialization and only enable it when
requested by mac80211. This allows us to get rid of the DIRTY_CONFIG flag,
because the device is now guaranteed to be completely initialized when brought
up by mac80211.
Signed-off-by: NMattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/rt2x00/rt2x00.h

@@ -636,7 +636,6 @@ enum rt2x00_flags {
 	DEVICE_STATE_STARTED_SUSPEND,
 	DEVICE_STATE_ENABLED_RADIO,
 	DEVICE_STATE_DISABLED_RADIO_HW,
-	DEVICE_STATE_DIRTY_CONFIG,
 
 	/*
 	 * Driver requirements

drivers/net/wireless/rt2x00/rt2x00dev.c

@@ -1014,21 +1014,11 @@ int rt2x00lib_start(struct rt2x00_dev *rt2x00dev)
 	if (retval)
 		return retval;
 
-	/*
-	 * Enable radio.
-	 */
-	retval = rt2x00lib_enable_radio(rt2x00dev);
-	if (retval) {
-		rt2x00lib_uninitialize(rt2x00dev);
-		return retval;
-	}
-
 	rt2x00dev->intf_ap_count = 0;
 	rt2x00dev->intf_sta_count = 0;
 	rt2x00dev->intf_associated = 0;
 
 	set_bit(DEVICE_STATE_STARTED, &rt2x00dev->flags);
-	set_bit(DEVICE_STATE_DIRTY_CONFIG, &rt2x00dev->flags);
 
 	return 0;
 }

drivers/net/wireless/rt2x00/rt2x00mac.c

@@ -338,7 +338,8 @@ EXPORT_SYMBOL_GPL(rt2x00mac_remove_interface);
 int rt2x00mac_config(struct ieee80211_hw *hw, struct ieee80211_conf *conf)
 {
 	struct rt2x00_dev *rt2x00dev = hw->priv;
-	int force_reconfig;
+	int radio_on;
+	int status;
 
 	/*
 	 * Mac80211 might be calling this function while we are trying
@@ -348,35 +349,34 @@ int rt2x00mac_config(struct ieee80211_hw *hw, struct ieee80211_conf *conf)
 		return 0;
 
 	/*
-	 * Check if we need to disable the radio,
-	 * if this is not the case, at least the RX must be disabled.
+	 * Only change device state when the radio is enabled. It does not
+	 * matter what parameters we have configured when the radio is disabled
+	 * because we won't be able to send or receive anyway. Also note that
+	 * some configuration parameters (e.g. channel and antenna values) can
+	 * only be set when the radio is enabled.
 	 */
-	if (test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags)) {
-		if (!conf->radio_enabled)
-			rt2x00lib_disable_radio(rt2x00dev);
-		else
+	radio_on = test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags);
+	if (conf->radio_enabled) {
+		/* For programming the values, we have to turn RX off */
 		rt2x00lib_toggle_rx(rt2x00dev, STATE_RADIO_RX_OFF);
-	}
-
-	/*
-	 * When the DEVICE_DIRTY_CONFIG flag is set, the device has recently
-	 * been started and the configuration must be forced upon the hardware.
-	 * Otherwise registers will not be intialized correctly and could
-	 * result in non-working hardware because essential registers aren't
-	 * initialized.
-	 */
-	force_reconfig =
-	    test_and_clear_bit(DEVICE_STATE_DIRTY_CONFIG, &rt2x00dev->flags);
 
-	rt2x00lib_config(rt2x00dev, conf, force_reconfig);
+		/* Enable the radio */
+		status = rt2x00lib_enable_radio(rt2x00dev);
+		if (unlikely(status))
+			return status;
 
 		/*
-	 * Reenable RX only if the radio should be on.
+		 * When we've just turned on the radio, we want to reprogram
+		 * everything to ensure a consistent state
 		 */
-	if (test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
+		rt2x00lib_config(rt2x00dev, conf, !radio_on);
+
+		/* Turn RX back on */
 		rt2x00lib_toggle_rx(rt2x00dev, STATE_RADIO_RX_ON);
-	else if (conf->radio_enabled)
-		return rt2x00lib_enable_radio(rt2x00dev);
+	} else {
+		/* Disable the radio */
+		rt2x00lib_disable_radio(rt2x00dev);
+	}
 
 	return 0;
 }