diff --git a/drivers/net/can/sja1000/Kconfig b/drivers/net/can/sja1000/Kconfig index 4c674927f2475da1c3109c59d796e81ce334f279..9e277d64a3183e1232b5ce604b80d7bdde635a79 100644 --- a/drivers/net/can/sja1000/Kconfig +++ b/drivers/net/can/sja1000/Kconfig @@ -44,4 +44,16 @@ config CAN_KVASER_PCI This driver is for the the PCIcanx and PCIcan cards (1, 2 or 4 channel) from Kvaser (http://www.kvaser.com). +config CAN_PLX_PCI + tristate "PLX90xx PCI-bridge based Cards" + depends on PCI + ---help--- + This driver is for CAN interface cards based on + the PLX90xx PCI bridge. + Driver supports now: + - Adlink PCI-7841/cPCI-7841 card (http://www.adlinktech.com/) + - Adlink PCI-7841/cPCI-7841 SE card + - Marathon CAN-bus-PCI card (http://www.marathon.ru/) + - TEWS TECHNOLOGIES TPMC810 card (http://www.tews.com/) + endif diff --git a/drivers/net/can/sja1000/Makefile b/drivers/net/can/sja1000/Makefile index 9d245ac0396571a6a838dca3eb7c68ee6cfa0d17..ce924553995d5d850c73f4e865a189f685795b18 100644 --- a/drivers/net/can/sja1000/Makefile +++ b/drivers/net/can/sja1000/Makefile @@ -8,5 +8,6 @@ obj-$(CONFIG_CAN_SJA1000_PLATFORM) += sja1000_platform.o obj-$(CONFIG_CAN_SJA1000_OF_PLATFORM) += sja1000_of_platform.o obj-$(CONFIG_CAN_EMS_PCI) += ems_pci.o obj-$(CONFIG_CAN_KVASER_PCI) += kvaser_pci.o +obj-$(CONFIG_CAN_PLX_PCI) += plx_pci.o ccflags-$(CONFIG_CAN_DEBUG_DEVICES) := -DDEBUG diff --git a/drivers/net/can/sja1000/plx_pci.c b/drivers/net/can/sja1000/plx_pci.c new file mode 100644 index 0000000000000000000000000000000000000000..6b46a6395f80218a76c1d1c5da70d24ab49b8b5e --- /dev/null +++ b/drivers/net/can/sja1000/plx_pci.c @@ -0,0 +1,472 @@ +/* + * Copyright (C) 2008-2010 Pavel Cheblakov + * + * Derived from the ems_pci.c driver: + * Copyright (C) 2007 Wolfgang Grandegger + * Copyright (C) 2008 Markus Plessing + * Copyright (C) 2008 Sebastian Haas + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the version 2 of the GNU General Public License + * as published by the Free Software Foundation + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software Foundation, + * Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "sja1000.h" + +#define DRV_NAME "sja1000_plx_pci" + +MODULE_AUTHOR("Pavel Cheblakov "); +MODULE_DESCRIPTION("Socket-CAN driver for PLX90xx PCI-bridge cards with " + "the SJA1000 chips"); +MODULE_SUPPORTED_DEVICE("Adlink PCI-7841/cPCI-7841, " + "Adlink PCI-7841/cPCI-7841 SE, " + "Marathon CAN-bus-PCI, " + "TEWS TECHNOLOGIES TPMC810"); +MODULE_LICENSE("GPL v2"); + +#define PLX_PCI_MAX_CHAN 2 + +struct plx_pci_card { + int channels; /* detected channels count */ + struct net_device *net_dev[PLX_PCI_MAX_CHAN]; + void __iomem *conf_addr; +}; + +#define PLX_PCI_CAN_CLOCK (16000000 / 2) + +/* PLX90xx registers */ +#define PLX_INTCSR 0x4c /* Interrupt Control/Status */ +#define PLX_CNTRL 0x50 /* User I/O, Direct Slave Response, + * Serial EEPROM, and Initialization + * Control register + */ + +#define PLX_LINT1_EN 0x1 /* Local interrupt 1 enable */ +#define PLX_LINT2_EN (1 << 3) /* Local interrupt 2 enable */ +#define PLX_PCI_INT_EN (1 << 6) /* PCI Interrupt Enable */ +#define PLX_PCI_RESET (1 << 30) /* PCI Adapter Software Reset */ + +/* + * The board configuration is probably following: + * RX1 is connected to ground. + * TX1 is not connected. + * CLKO is not connected. + * Setting the OCR register to 0xDA is a good idea. + * This means normal output mode, push-pull and the correct polarity. + */ +#define PLX_PCI_OCR (OCR_TX0_PUSHPULL | OCR_TX1_PUSHPULL) + +/* + * In the CDR register, you should set CBP to 1. + * You will probably also want to set the clock divider value to 7 + * (meaning direct oscillator output) because the second SJA1000 chip + * is driven by the first one CLKOUT output. + */ +#define PLX_PCI_CDR (CDR_CBP | CDR_CLKOUT_MASK) + +/* SJA1000 Control Register in the BasicCAN Mode */ +#define REG_CR 0x00 + +/* States of some SJA1000 registers after hardware reset in the BasicCAN mode*/ +#define REG_CR_BASICCAN_INITIAL 0x21 +#define REG_CR_BASICCAN_INITIAL_MASK 0xa1 +#define REG_SR_BASICCAN_INITIAL 0x0c +#define REG_IR_BASICCAN_INITIAL 0xe0 + +/* States of some SJA1000 registers after hardware reset in the PeliCAN mode*/ +#define REG_MOD_PELICAN_INITIAL 0x01 +#define REG_SR_PELICAN_INITIAL 0x3c +#define REG_IR_PELICAN_INITIAL 0x00 + +#define ADLINK_PCI_VENDOR_ID 0x144A +#define ADLINK_PCI_DEVICE_ID 0x7841 + +#define MARATHON_PCI_DEVICE_ID 0x2715 + +#define TEWS_PCI_VENDOR_ID 0x1498 +#define TEWS_PCI_DEVICE_ID_TMPC810 0x032A + +static void plx_pci_reset_common(struct pci_dev *pdev); +static void plx_pci_reset_marathon(struct pci_dev *pdev); + +struct plx_pci_channel_map { + u32 bar; + u32 offset; + u32 size; /* 0x00 - auto, e.g. length of entire bar */ +}; + +struct plx_pci_card_info { + const char *name; + int channel_count; + u32 can_clock; + u8 ocr; /* output control register */ + u8 cdr; /* clock divider register */ + + /* Parameters for mapping local configuration space */ + struct plx_pci_channel_map conf_map; + + /* Parameters for mapping the SJA1000 chips */ + struct plx_pci_channel_map chan_map_tbl[PLX_PCI_MAX_CHAN]; + + /* Pointer to device-dependent reset function */ + void (*reset_func)(struct pci_dev *pdev); +}; + +static struct plx_pci_card_info plx_pci_card_info_adlink __devinitdata = { + "Adlink PCI-7841/cPCI-7841", 2, + PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR, + {1, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x80, 0x80} }, + &plx_pci_reset_common + /* based on PLX9052 */ +}; + +static struct plx_pci_card_info plx_pci_card_info_adlink_se __devinitdata = { + "Adlink PCI-7841/cPCI-7841 SE", 2, + PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR, + {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x80, 0x80} }, + &plx_pci_reset_common + /* based on PLX9052 */ +}; + +static struct plx_pci_card_info plx_pci_card_info_marathon __devinitdata = { + "Marathon CAN-bus-PCI", 2, + PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR, + {0, 0x00, 0x00}, { {2, 0x00, 0x00}, {4, 0x00, 0x00} }, + &plx_pci_reset_marathon + /* based on PLX9052 */ +}; + +static struct plx_pci_card_info plx_pci_card_info_tews __devinitdata = { + "TEWS TECHNOLOGIES TPMC810", 2, + PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR, + {0, 0x00, 0x00}, { {2, 0x000, 0x80}, {2, 0x100, 0x80} }, + &plx_pci_reset_common + /* based on PLX9030 */ +}; + +static DEFINE_PCI_DEVICE_TABLE(plx_pci_tbl) = { + { + /* Adlink PCI-7841/cPCI-7841 */ + ADLINK_PCI_VENDOR_ID, ADLINK_PCI_DEVICE_ID, + PCI_ANY_ID, PCI_ANY_ID, + PCI_CLASS_NETWORK_OTHER << 8, ~0, + (kernel_ulong_t)&plx_pci_card_info_adlink + }, + { + /* Adlink PCI-7841/cPCI-7841 SE */ + ADLINK_PCI_VENDOR_ID, ADLINK_PCI_DEVICE_ID, + PCI_ANY_ID, PCI_ANY_ID, + PCI_CLASS_COMMUNICATION_OTHER << 8, ~0, + (kernel_ulong_t)&plx_pci_card_info_adlink_se + }, + { + /* Marathon CAN-bus-PCI card */ + PCI_VENDOR_ID_PLX, MARATHON_PCI_DEVICE_ID, + PCI_ANY_ID, PCI_ANY_ID, + 0, 0, + (kernel_ulong_t)&plx_pci_card_info_marathon + }, + { + /* TEWS TECHNOLOGIES TPMC810 card */ + TEWS_PCI_VENDOR_ID, TEWS_PCI_DEVICE_ID_TMPC810, + PCI_ANY_ID, PCI_ANY_ID, + 0, 0, + (kernel_ulong_t)&plx_pci_card_info_tews + }, + { 0,} +}; +MODULE_DEVICE_TABLE(pci, plx_pci_tbl); + +static u8 plx_pci_read_reg(const struct sja1000_priv *priv, int port) +{ + return ioread8(priv->reg_base + port); +} + +static void plx_pci_write_reg(const struct sja1000_priv *priv, int port, u8 val) +{ + iowrite8(val, priv->reg_base + port); +} + +/* + * Check if a CAN controller is present at the specified location + * by trying to switch 'em from the Basic mode into the PeliCAN mode. + * Also check states of some registers in reset mode. + */ +static inline int plx_pci_check_sja1000(const struct sja1000_priv *priv) +{ + int flag = 0; + + /* + * Check registers after hardware reset (the Basic mode) + * See states on p. 10 of the Datasheet. + */ + if ((priv->read_reg(priv, REG_CR) & REG_CR_BASICCAN_INITIAL_MASK) == + REG_CR_BASICCAN_INITIAL && + (priv->read_reg(priv, REG_SR) == REG_SR_BASICCAN_INITIAL) && + (priv->read_reg(priv, REG_IR) == REG_IR_BASICCAN_INITIAL)) + flag = 1; + + /* Bring the SJA1000 into the PeliCAN mode*/ + priv->write_reg(priv, REG_CDR, CDR_PELICAN); + + /* + * Check registers after reset in the PeliCAN mode. + * See states on p. 23 of the Datasheet. + */ + if (priv->read_reg(priv, REG_MOD) == REG_MOD_PELICAN_INITIAL && + priv->read_reg(priv, REG_SR) == REG_SR_PELICAN_INITIAL && + priv->read_reg(priv, REG_IR) == REG_IR_PELICAN_INITIAL) + return flag; + + return 0; +} + +/* + * PLX90xx software reset + * Also LRESET# asserts and brings to reset device on the Local Bus (if wired). + * For most cards it's enough for reset the SJA1000 chips. + */ +static void plx_pci_reset_common(struct pci_dev *pdev) +{ + struct plx_pci_card *card = pci_get_drvdata(pdev); + u32 cntrl; + + cntrl = ioread32(card->conf_addr + PLX_CNTRL); + cntrl |= PLX_PCI_RESET; + iowrite32(cntrl, card->conf_addr + PLX_CNTRL); + udelay(100); + cntrl ^= PLX_PCI_RESET; + iowrite32(cntrl, card->conf_addr + PLX_CNTRL); +}; + +/* Special reset function for Marathon card */ +static void plx_pci_reset_marathon(struct pci_dev *pdev) +{ + void __iomem *reset_addr; + int i; + int reset_bar[2] = {3, 5}; + + plx_pci_reset_common(pdev); + + for (i = 0; i < 2; i++) { + reset_addr = pci_iomap(pdev, reset_bar[i], 0); + if (!reset_addr) { + dev_err(&pdev->dev, "Failed to remap reset " + "space %d (BAR%d)\n", i, reset_bar[i]); + } else { + /* reset the SJA1000 chip */ + iowrite8(0x1, reset_addr); + udelay(100); + pci_iounmap(pdev, reset_addr); + } + } +} + +static void plx_pci_del_card(struct pci_dev *pdev) +{ + struct plx_pci_card *card = pci_get_drvdata(pdev); + struct net_device *dev; + struct sja1000_priv *priv; + int i = 0; + + for (i = 0; i < card->channels; i++) { + dev = card->net_dev[i]; + if (!dev) + continue; + + dev_info(&pdev->dev, "Removing %s\n", dev->name); + unregister_sja1000dev(dev); + priv = netdev_priv(dev); + if (priv->reg_base) + pci_iounmap(pdev, priv->reg_base); + free_sja1000dev(dev); + } + + plx_pci_reset_common(pdev); + + /* + * Disable interrupts from PCI-card (PLX90xx) and disable Local_1, + * Local_2 interrupts + */ + iowrite32(0x0, card->conf_addr + PLX_INTCSR); + + if (card->conf_addr) + pci_iounmap(pdev, card->conf_addr); + + kfree(card); + + pci_disable_device(pdev); + pci_set_drvdata(pdev, NULL); +} + +/* + * Probe PLX90xx based device for the SJA1000 chips and register each + * available CAN channel to SJA1000 Socket-CAN subsystem. + */ +static int __devinit plx_pci_add_card(struct pci_dev *pdev, + const struct pci_device_id *ent) +{ + struct sja1000_priv *priv; + struct net_device *dev; + struct plx_pci_card *card; + struct plx_pci_card_info *ci; + int err, i; + u32 val; + void __iomem *addr; + + ci = (struct plx_pci_card_info *)ent->driver_data; + + if (pci_enable_device(pdev) < 0) { + dev_err(&pdev->dev, "Failed to enable PCI device\n"); + return -ENODEV; + } + + dev_info(&pdev->dev, "Detected \"%s\" card at slot #%i\n", + ci->name, PCI_SLOT(pdev->devfn)); + + /* Allocate card structures to hold addresses, ... */ + card = kzalloc(sizeof(*card), GFP_KERNEL); + if (!card) { + dev_err(&pdev->dev, "Unable to allocate memory\n"); + pci_disable_device(pdev); + return -ENOMEM; + } + + pci_set_drvdata(pdev, card); + + card->channels = 0; + + /* Remap PLX90xx configuration space */ + addr = pci_iomap(pdev, ci->conf_map.bar, ci->conf_map.size); + if (!addr) { + err = -ENOMEM; + dev_err(&pdev->dev, "Failed to remap configuration space " + "(BAR%d)\n", ci->conf_map.bar); + goto failure_cleanup; + } + card->conf_addr = addr + ci->conf_map.offset; + + ci->reset_func(pdev); + + /* Detect available channels */ + for (i = 0; i < ci->channel_count; i++) { + struct plx_pci_channel_map *cm = &ci->chan_map_tbl[i]; + + dev = alloc_sja1000dev(0); + if (!dev) { + err = -ENOMEM; + goto failure_cleanup; + } + + card->net_dev[i] = dev; + priv = netdev_priv(dev); + priv->priv = card; + priv->irq_flags = IRQF_SHARED; + + dev->irq = pdev->irq; + + /* + * Remap IO space of the SJA1000 chips + * This is device-dependent mapping + */ + addr = pci_iomap(pdev, cm->bar, cm->size); + if (!addr) { + err = -ENOMEM; + dev_err(&pdev->dev, "Failed to remap BAR%d\n", cm->bar); + goto failure_cleanup; + } + + priv->reg_base = addr + cm->offset; + priv->read_reg = plx_pci_read_reg; + priv->write_reg = plx_pci_write_reg; + + /* Check if channel is present */ + if (plx_pci_check_sja1000(priv)) { + priv->can.clock.freq = ci->can_clock; + priv->ocr = ci->ocr; + priv->cdr = ci->cdr; + + SET_NETDEV_DEV(dev, &pdev->dev); + + /* Register SJA1000 device */ + err = register_sja1000dev(dev); + if (err) { + dev_err(&pdev->dev, "Registering device failed " + "(err=%d)\n", err); + free_sja1000dev(dev); + goto failure_cleanup; + } + + card->channels++; + + dev_info(&pdev->dev, "Channel #%d at 0x%p, irq %d " + "registered as %s\n", i + 1, priv->reg_base, + dev->irq, dev->name); + } else { + dev_err(&pdev->dev, "Channel #%d not detected\n", + i + 1); + free_sja1000dev(dev); + } + } + + if (!card->channels) { + err = -ENODEV; + goto failure_cleanup; + } + + /* + * Enable interrupts from PCI-card (PLX90xx) and enable Local_1, + * Local_2 interrupts from the SJA1000 chips + */ + val = ioread32(card->conf_addr + PLX_INTCSR); + val |= PLX_LINT1_EN | PLX_LINT2_EN | PLX_PCI_INT_EN; + iowrite32(val, card->conf_addr + PLX_INTCSR); + + return 0; + +failure_cleanup: + dev_err(&pdev->dev, "Error: %d. Cleaning Up.\n", err); + + plx_pci_del_card(pdev); + + return err; +} + +static struct pci_driver plx_pci_driver = { + .name = DRV_NAME, + .id_table = plx_pci_tbl, + .probe = plx_pci_add_card, + .remove = plx_pci_del_card, +}; + +static int __init plx_pci_init(void) +{ + return pci_register_driver(&plx_pci_driver); +} + +static void __exit plx_pci_exit(void) +{ + pci_unregister_driver(&plx_pci_driver); +} + +module_init(plx_pci_init); +module_exit(plx_pci_exit);