media: atomisp: fix dummy_ptr check to avoid duplicate active_bo
stable inclusion from stable-v5.10.110 commit 41082d6432e5d8cfaaa49a3864c88a16535f8e95 bugzilla: https://gitee.com/openeuler/kernel/issues/I574AL Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=41082d6432e5d8cfaaa49a3864c88a16535f8e95 -------------------------------- [ Upstream commit 127efdbc ] The dummy_ptr check in hmm_init() [1] results in the following "hmm_init Failed to create sysfs" error exactly once every two times on atomisp reload by rmmod/insmod (although atomisp module loads and works fine regardless of this error): [ 140.230662] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:03.0/active_bo' [ 140.230668] CPU: 1 PID: 2502 Comm: insmod Tainted: G C OE 5.15.0-rc4-1-surface-mainline #1 b8acf6eb64994414b2e20bad312a7a2c45f748f9 [ 140.230675] Hardware name: OEMB OEMB/OEMB, BIOS 1.51116.238 03/09/2015 [ 140.230678] Call Trace: [ 140.230687] dump_stack_lvl+0x46/0x5a [ 140.230702] sysfs_warn_dup.cold+0x17/0x24 [ 140.230710] sysfs_add_file_mode_ns+0x160/0x170 [ 140.230717] internal_create_group+0x126/0x390 [ 140.230723] hmm_init+0x5c/0x70 [atomisp 7a6a680bf400629363d2a6f58fd10e7299678b99] [ 140.230811] atomisp_pci_probe.cold+0x1136/0x148e [atomisp 7a6a680bf400629363d2a6f58fd10e7299678b99] [ 140.230875] local_pci_probe+0x45/0x80 [ 140.230882] ? pci_match_device+0xd7/0x130 [ 140.230887] pci_device_probe+0xfa/0x1b0 [ 140.230892] really_probe+0x1f5/0x3f0 [ 140.230899] __driver_probe_device+0xfe/0x180 [ 140.230903] driver_probe_device+0x1e/0x90 [ 140.230908] __driver_attach+0xc0/0x1c0 [ 140.230912] ? __device_attach_driver+0xe0/0xe0 [ 140.230915] ? __device_attach_driver+0xe0/0xe0 [ 140.230919] bus_for_each_dev+0x89/0xd0 [ 140.230924] bus_add_driver+0x12b/0x1e0 [ 140.230929] driver_register+0x8f/0xe0 [ 140.230933] ? 0xffffffffc153f000 [ 140.230937] do_one_initcall+0x57/0x220 [ 140.230945] do_init_module+0x5c/0x260 [ 140.230952] load_module+0x24bd/0x26a0 [ 140.230962] ? __do_sys_finit_module+0xae/0x110 [ 140.230966] __do_sys_finit_module+0xae/0x110 [ 140.230972] do_syscall_64+0x5c/0x80 [ 140.230979] ? syscall_exit_to_user_mode+0x23/0x40 [ 140.230983] ? do_syscall_64+0x69/0x80 [ 140.230988] ? exc_page_fault+0x72/0x170 [ 140.230991] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 140.230997] RIP: 0033:0x7f7fd5d8718d [ 140.231003] Code: b4 0c 00 0f 05 eb a9 66 0f 1f 44 00 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d b3 6c 0c 00 f7 d8 64 89 01 48 [ 140.231006] RSP: 002b:00007ffefc25f0e8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139 [ 140.231012] RAX: ffffffffffffffda RBX: 000055ac3edcd7f0 RCX: 00007f7fd5d8718d [ 140.231015] RDX: 0000000000000000 RSI: 000055ac3d723270 RDI: 0000000000000003 [ 140.231017] RBP: 0000000000000000 R08: 0000000000000000 R09: 00007f7fd5e52380 [ 140.231019] R10: 0000000000000003 R11: 0000000000000246 R12: 000055ac3d723270 [ 140.231021] R13: 0000000000000000 R14: 000055ac3edd06e0 R15: 0000000000000000 [ 140.231038] atomisp-isp2 0000:00:03.0: hmm_init Failed to create sysfs The problem is that dummy_ptr == 0 is a valid value. So, change the logic which checks if dummy_ptr was allocated. At this point, atomisp now gives WARN_ON() in hmm_free() [2] on atomisp reload by rmmod/insmod. Again, the check is wrong there. So, change both checks for mmgr_EXCEPTION, which is the error value when HMM allocation fails, and initialize dummy_ptr with such value. [1] added on commit d9ab8395 ("media: atomisp: don't cause a warn if probe failed") [2] added on commit b83cc378 ("atomisp: clean up the hmm init/cleanup indirections") Link: https://lore.kernel.org/linux-media/20211017162337.44860-3-kitakar@gmail.comSigned-off-by: NTsuchiya Yuto <kitakar@gmail.com> Co-developed-by: NMauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: NSasha Levin <sashal@kernel.org> Signed-off-by: NYu Liao <liaoyu15@huawei.com> Reviewed-by: NWei Li <liwei391@huawei.com> Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>
Showing
想要评论请 注册 或 登录