Skip to content

K
Kernel

openeuler / Kernel
大约 2 年 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
“1567f5cbe8e86d3437273d970c8d3f422ddf8f96”上不存在“...mapfiles/git@gitcode.net:openanolis/dragonwell8_jdk.git”
提交 16a5fd92 编写于 作者: Y Yuval Mintz 提交者： David S. Miller
浏览文件
操作

bnx2x: Revise comments and alignment 

This patch correct various typos, fix comments conventions and
adds/removes a few comments.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 d76a6111
显示空白变更内容
内联 并排
Showing with 251 addition and 307 deletion
drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
浏览文件 @ 16a5fd92
......@@ -362,7 +362,7 @@ union db_prod {
/*
* Number of required SGEs is the sum of two:
* 1. Number of possible opened aggregations (next packet for
* these aggregations will probably consume SGE immidiatelly)
* these aggregations will probably consume SGE immediately)
* 2. Rest of BRB blocks divided by 2 (block will consume new SGE only
* after placement on BD for new TPA aggregation)
*
......@@ -486,10 +486,10 @@ struct bnx2x_fastpath {
struct napi_struct napi;
union host_hc_status_block status_blk;
/* chip independed shortcuts into sb structure */
/* chip independent shortcuts into sb structure */
__le16 *sb_index_values;
__le16 *sb_running_index;
/* chip independed shortcut into rx_prods_offset memory */
/* chip independent shortcut into rx_prods_offset memory */
u32 ustorm_rx_prods_offset;
u32 rx_buf_size;
......@@ -603,7 +603,7 @@ struct bnx2x_fastpath {
* START_BD(splitted) - includes unpaged data segment for GSO
* PARSING_BD - for TSO and CSUM data
* PARSING_BD2 - for encapsulation data
* Frag BDs - decribes pages for frags
* Frag BDs - describes pages for frags
*/
#define BDS_PER_TX_PKT 4
#define MAX_BDS_PER_TX_PKT (MAX_SKB_FRAGS + BDS_PER_TX_PKT)
......@@ -886,14 +886,14 @@ struct bnx2x_common {
#define CHIP_IS_E3A0(bp) (CHIP_IS_E3(bp) && \
(CHIP_REV(bp) == CHIP_REV_Ax))
/* This define is used in two main places:
* 1. In the early stages of nic_load, to know if to configrue Parser / Searcher
* 1. In the early stages of nic_load, to know if to configure Parser / Searcher
* to nic-only mode or to offload mode. Offload mode is configured if either the
* chip is E1x (where MIC_MODE register is not applicable), or if cnic already
* registered for this port (which means that the user wants storage services).
* 2. During cnic-related load, to know if offload mode is already configured in
* the HW or needs to be configrued.
* the HW or needs to be configured.
* Since the transition from nic-mode to offload-mode in HW causes traffic
* coruption, nic-mode is configured only in ports on which storage services
* corruption, nic-mode is configured only in ports on which storage services
* where never requested.
*/
#define CONFIGURE_NIC_MODE(bp) (!CHIP_IS_E1x(bp) && !CNIC_ENABLED(bp))
......@@ -994,14 +994,14 @@ extern struct workqueue_struct *bnx2x_wq;
* If the maximum number of FP-SB available is X then:
* a. If CNIC is supported it consumes 1 FP-SB thus the max number of
* regular L2 queues is Y=X-1
* b. in MF mode the actual number of L2 queues is Y= (X-1/MF_factor)
* b. In MF mode the actual number of L2 queues is Y= (X-1/MF_factor)
* c. If the FCoE L2 queue is supported the actual number of L2 queues
* is Y+1
* d. The number of irqs (MSIX vectors) is either Y+1 (one extra for
* slow-path interrupts) or Y+2 if CNIC is supported (one additional
* FP interrupt context for the CNIC).
* e. The number of HW context (CID count) is always X or X+1 if FCoE
* L2 queue is supported. the cid for the FCoE L2 queue is always X.
* L2 queue is supported. The cid for the FCoE L2 queue is always X.
*/
/* fast-path interrupt contexts E1x */
......@@ -1568,7 +1568,7 @@ struct bnx2x {
struct mutex cnic_mutex;
struct bnx2x_vlan_mac_obj iscsi_l2_mac_obj;
/* Start index of the "special" (CNIC related) L2 cleints */
/* Start index of the "special" (CNIC related) L2 clients */
u8 cnic_base_cl_id;
int dmae_ready;
......@@ -1682,7 +1682,7 @@ struct bnx2x {
/* operation indication for the sp_rtnl task */
unsigned long sp_rtnl_state;
/* DCBX Negotation results */
/* DCBX Negotiation results */
struct dcbx_features dcbx_local_feat;
u32 dcbx_error;
......@@ -2042,7 +2042,8 @@ void bnx2x_igu_clear_sb_gen(struct bnx2x *bp, u8 func, u8 idu_sb_id,
#define DMAE_LEN32_WR_MAX(bp) (CHIP_IS_E1(bp) ? 0x400 : 0x2000)
#define DMAE_COMP_VAL 0x60d0d0ae /* E2 and on - upper bit
indicates eror */
* indicates error
*/
#define MAX_DMAE_C_PER_PORT 8
#define INIT_DMAE_C(bp) (BP_PORT(bp) * MAX_DMAE_C_PER_PORT + \
......
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
浏览文件 @ 16a5fd92
......@@ -124,7 +124,7 @@ static void bnx2x_shrink_eth_fp(struct bnx2x *bp, int delta)
int i, cos, old_eth_num = BNX2X_NUM_ETH_QUEUES(bp);
/* Queue pointer cannot be re-set on an fp-basis, as moving pointer
* backward along the array could cause memory to be overriden
* backward along the array could cause memory to be overridden
*/
for (cos = 1; cos < bp->max_cos; cos++) {
for (i = 0; i < old_eth_num - delta; i++) {
......@@ -258,7 +258,7 @@ int bnx2x_tx_int(struct bnx2x *bp, struct bnx2x_fp_txdata *txdata)
smp_mb();
if (unlikely(netif_tx_queue_stopped(txq))) {
/* Taking tx_lock() is needed to prevent reenabling the queue
/* Taking tx_lock() is needed to prevent re-enabling the queue
* while it's empty. This could have happen if rx_action() gets
* suspended in bnx2x_tx_int() after the condition before
* netif_tx_wake_queue(), while tx_action (bnx2x_start_xmit()):
......@@ -571,7 +571,7 @@ static int bnx2x_fill_frag_skb(struct bnx2x *bp, struct bnx2x_fastpath *fp,
return err;
}
/* Unmap the page as we r going to pass it to the stack */
/* Unmap the page as we're going to pass it to the stack */
dma_unmap_page(&bp->pdev->dev,
dma_unmap_addr(&old_rx_pg, mapping),
SGE_PAGES, DMA_FROM_DEVICE);
......@@ -1114,7 +1114,7 @@ static void bnx2x_fill_report_data(struct bnx2x *bp,
memset(data, 0, sizeof(*data));
/* Fill the report data: efective line speed */
/* Fill the report data: effective line speed */
data->line_speed = line_speed;
/* Link is down */
......@@ -1157,7 +1157,7 @@ void bnx2x_link_report(struct bnx2x *bp)
*
* @bp: driver handle
*
* None atomic inmlementation.
* None atomic implementation.
* Should be called under the phy_lock.
*/
void __bnx2x_link_report(struct bnx2x *bp)
......@@ -1300,7 +1300,7 @@ void bnx2x_init_rx_rings(struct bnx2x *bp)
"mtu %d rx_buf_size %d\n", bp->dev->mtu, fp->rx_buf_size);
if (!fp->disable_tpa) {
/* Fill the per-aggregtion pool */
/* Fill the per-aggregation pool */
for (i = 0; i < MAX_AGG_QS(bp); i++) {
struct bnx2x_agg_info *tpa_info =
&fp->tpa_info[i];
......@@ -1858,7 +1858,7 @@ void bnx2x_set_num_queues(struct bnx2x *bp)
*
* If the actual number of Tx queues (for each CoS) is less than 16 then there
* will be the holes at the end of each group of 16 ETh L2 indices (0..15,
* 16..31,...) with indicies that are not coupled with any real Tx queue.
* 16..31,...) with indices that are not coupled with any real Tx queue.
*
* The proper configuration of skb->queue_mapping is handled by
* bnx2x_select_queue() and __skb_tx_hash().
......@@ -1920,7 +1920,7 @@ static void bnx2x_set_rx_buf_size(struct bnx2x *bp)
ETH_OVREHEAD +
mtu +
BNX2X_FW_RX_ALIGN_END;
/* Note : rx_buf_size doesnt take into account NET_SKB_PAD */
/* Note : rx_buf_size doesn't take into account NET_SKB_PAD */
if (fp->rx_buf_size + NET_SKB_PAD <= PAGE_SIZE)
fp->rx_frag_size = fp->rx_buf_size + NET_SKB_PAD;
else
......@@ -1933,7 +1933,7 @@ static int bnx2x_init_rss_pf(struct bnx2x *bp)
int i;
u8 num_eth_queues = BNX2X_NUM_ETH_QUEUES(bp);
/* Prepare the initial contents fo the indirection table if RSS is
/* Prepare the initial contents for the indirection table if RSS is
* enabled
*/
for (i = 0; i < sizeof(bp->rss_conf_obj.ind_table); i++)
......@@ -2011,7 +2011,7 @@ static int bnx2x_init_hw(struct bnx2x *bp, u32 load_code)
/*
* Cleans the object that have internal lists without sending
* ramrods. Should be run when interrutps are disabled.
* ramrods. Should be run when interrupts are disabled.
*/
void bnx2x_squeeze_objects(struct bnx2x *bp)
{
......@@ -2347,8 +2347,7 @@ static void bnx2x_bz_fp(struct bnx2x *bp, int index)
fp->txdata_ptr[cos] = &bp->bnx2x_txq[cos *
BNX2X_NUM_ETH_QUEUES(bp) + index];
/*
* set the tpa flag for each queue. The tpa flag determines the queue
/* set the tpa flag for each queue. The tpa flag determines the queue
* minimal size so it must be set prior to queue memory allocation
*/
fp->disable_tpa = !(bp->flags & TPA_ENABLE_FLAG ||
......@@ -2473,6 +2472,7 @@ int bnx2x_nic_load(struct bnx2x *bp, int load_mode)
bp->state = BNX2X_STATE_OPENING_WAIT4_LOAD;
/* zero the structure w/o any lock, before SP handler is initialized */
memset(&bp->last_reported_link, 0, sizeof(bp->last_reported_link));
__set_bit(BNX2X_LINK_REPORT_LINK_DOWN,
&bp->last_reported_link.link_report_flags);
......@@ -2537,8 +2537,8 @@ int bnx2x_nic_load(struct bnx2x *bp, int load_mode)
}
/* configure multi cos mappings in kernel.
* this configuration may be overriden by a multi class queue discipline
* or by a dcbx negotiation result.
* this configuration may be overridden by a multi class queue
* discipline or by a dcbx negotiation result.
*/
bnx2x_setup_tc(bp->dev, bp->max_cos);
......@@ -2697,7 +2697,7 @@ int bnx2x_nic_load(struct bnx2x *bp, int load_mode)
/* Start the Tx */
switch (load_mode) {
case LOAD_NORMAL:
/* Tx queue should be only reenabled */
/* Tx queue should be only re-enabled */
netif_tx_wake_all_queues(bp->dev);
break;
......@@ -2842,7 +2842,7 @@ int bnx2x_nic_unload(struct bnx2x *bp, int unload_mode, bool keep_link)
}
/* Nothing to do during unload if previous bnx2x_nic_load()
* have not completed succesfully - all resourses are released.
* have not completed successfully - all resources are released.
*
* we can get here only after unsuccessful ndo_* callback, during which
* dev->IFF_UP flag is still on.
......@@ -2891,10 +2891,9 @@ int bnx2x_nic_unload(struct bnx2x *bp, int unload_mode, bool keep_link)
/* Send the UNLOAD_REQUEST to the MCP */
bnx2x_send_unload_req(bp, unload_mode);
/*
* Prevent transactions to host from the functions on the
/* Prevent transactions to host from the functions on the
* engine that doesn't reset global blocks in case of global
* attention once gloabl blocks are reset and gates are opened
* attention once global blocks are reset and gates are opened
* (the engine which leader will perform the recovery
* last).
*/
......@@ -2915,7 +2914,7 @@ int bnx2x_nic_unload(struct bnx2x *bp, int unload_mode, bool keep_link)
}
/*
* At this stage no more interrupts will arrive so we may safly clean
* At this stage no more interrupts will arrive so we may safely clean
* the queueable objects here in case they failed to get cleaned so far.
*/
if (IS_PF(bp))
......@@ -3587,7 +3586,7 @@ netdev_tx_t bnx2x_start_xmit(struct sk_buff *skb, struct net_device *dev)
DP(NETIF_MSG_TX_QUEUED, "indices: txq %d, fp %d, txdata %d\n",
txq_index, fp_index, txdata_index); */
/* enable this debug print to view the tranmission details
/* enable this debug print to view the transmission details
DP(NETIF_MSG_TX_QUEUED,
"transmitting packet cid %d fp index %d txdata_index %d tx_data ptr %p fp pointer %p\n",
txdata->cid, fp_index, txdata_index, txdata, fp); */
......@@ -3970,7 +3969,7 @@ int bnx2x_setup_tc(struct net_device *dev, u8 num_tc)
/* setup tc must be called under rtnl lock */
ASSERT_RTNL();
/* no traffic classes requested. aborting */
/* no traffic classes requested. Aborting */
if (!num_tc) {
netdev_reset_tc(dev);
return 0;
......@@ -3997,8 +3996,7 @@ int bnx2x_setup_tc(struct net_device *dev, u8 num_tc)
prio, bp->prio_to_cos[prio]);
}
/* Use this configuration to diffrentiate tc0 from other COSes
/* Use this configuration to differentiate tc0 from other COSes
This can be used for ets or pfc, and save the effort of setting
up a multio class queue disc or negotiating DCBX with a switch
netdev_set_prio_tc_map(dev, 0, 0);
......@@ -4629,7 +4627,7 @@ int bnx2x_set_features(struct net_device *dev, netdev_features_t features)
changes = flags ^ bp->flags;
/* if GRO is changed while LRO is enabled, dont force a reload */
/* if GRO is changed while LRO is enabled, don't force a reload */
if ((changes & GRO_ENABLE_FLAG) && (flags & TPA_ENABLE_FLAG))
changes &= ~GRO_ENABLE_FLAG;
......
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h
浏览文件 @ 16a5fd92
......@@ -1331,8 +1331,8 @@ static inline bool bnx2x_mtu_allows_gro(int mtu)
int fpp = SGE_PAGE_SIZE / (mtu - ETH_MAX_TPA_HEADER_SIZE);
/*
* 1. number of frags should not grow above MAX_SKB_FRAGS
* 2. frag must fit the page
* 1. Number of frags should not grow above MAX_SKB_FRAGS
* 2. Frag must fit the page
*/
return mtu <= SGE_PAGE_SIZE && (U_ETH_SGL_SIZE * fpp) <= MAX_SKB_FRAGS;
}
......
drivers/net/ethernet/broadcom/bnx2x/bnx2x_dcb.c
浏览文件 @ 16a5fd92
......@@ -687,7 +687,7 @@ static inline void bnx2x_dcbx_update_tc_mapping(struct bnx2x *bp)
}
/* setup tc must be called under rtnl lock, but we can't take it here
* as we are handling an attetntion on a work queue which must be
* as we are handling an attention on a work queue which must be
* flushed at some rtnl-locked contexts (e.g. if down)
*/
if (!test_and_set_bit(BNX2X_SP_RTNL_SETUP_TC, &bp->sp_rtnl_state))
......@@ -707,7 +707,7 @@ void bnx2x_dcbx_set_params(struct bnx2x *bp, u32 state)
*/
bnx2x_dcbnl_update_applist(bp, true);
/* Read rmeote mib if dcbx is in the FW */
/* Read remote mib if dcbx is in the FW */
if (bnx2x_dcbx_read_shmem_remote_mib(bp))
return;
#endif
......@@ -738,7 +738,7 @@ void bnx2x_dcbx_set_params(struct bnx2x *bp, u32 state)
bnx2x_dcbx_update_tc_mapping(bp);
/*
* allow other funtions to update their netdevices
* allow other functions to update their netdevices
* accordingly
*/
if (IS_MF(bp))
......@@ -860,7 +860,7 @@ static void bnx2x_dcbx_admin_mib_updated_params(struct bnx2x *bp,
i, DCBX_PRI_PG_GET(af->ets.pri_pg_tbl, i));
}
/*For IEEE admin_recommendation_bw_precentage
/*For IEEE admin_recommendation_bw_percentage
*For IEEE admin_recommendation_ets_pg */
af->pfc.pri_en_bitmap = (u8)dp->admin_pfc_bitmap;
for (i = 0; i < DCBX_CONFIG_MAX_APP_PROTOCOL; i++) {
......@@ -1070,7 +1070,7 @@ static void bnx2x_dcbx_get_num_pg_traf_type(struct bnx2x *bp,
bool pg_found = false;
u32 i, traf_type, add_traf_type, add_pg;
u32 *ttp = bp->dcbx_port_params.app.traffic_type_priority;
struct pg_entry_help_data *data = help_data->data; /*shotcut*/
struct pg_entry_help_data *data = help_data->data; /*shortcut*/
/* Set to invalid */
for (i = 0; i < LLFC_DRIVER_TRAFFIC_TYPE_MAX; i++)
......@@ -1166,7 +1166,8 @@ static void bnx2x_dcbx_separate_pauseable_from_non(struct bnx2x *bp,
DCBX_PG_BW_GET(ets->pg_bw_tbl, pg_entry));
else
/* If we join a group and one is strict
* than the bw rulls */
* than the bw rules
*/
cos_data->data[entry].strict =
BNX2X_DCBX_STRICT_COS_HIGHEST;
}
......@@ -1277,7 +1278,7 @@ static void bnx2x_dcbx_2cos_limit_cee_single_pg_to_cos_params(struct bnx2x *bp,
} else {
/* If there are only pauseable priorities or
* only non-pauseable,* the lower priorities go
* to the first queue and the higherpriorities go
* to the first queue and the higher priorities go
* to the second queue.
*/
cos_data->data[0].pausable =
......@@ -1477,7 +1478,7 @@ static void bnx2x_dcbx_2cos_limit_cee_three_pg_to_cos_params(
* queue and one priority goes to the second queue.
*
* We will join this two cases:
* if one is BW limited it will go to the secoend queue
* if one is BW limited it will go to the second queue
* otherwise the last priority will get it
*/
......@@ -1497,7 +1498,8 @@ static void bnx2x_dcbx_2cos_limit_cee_three_pg_to_cos_params(
false == b_found_strict)
/* last entry will be handled separately
* If no priority is strict than last
* enty goes to last queue.*/
* entry goes to last queue.
*/
entry = 1;
cos_data->data[entry].pri_join_mask |=
pri_tested;
......@@ -1509,7 +1511,8 @@ static void bnx2x_dcbx_2cos_limit_cee_three_pg_to_cos_params(
b_found_strict = true;
cos_data->data[1].pri_join_mask |= pri_tested;
/* If we join a group and one is strict
* than the bw rulls */
* than the bw rules
*/
cos_data->data[1].strict =
BNX2X_DCBX_STRICT_COS_HIGHEST;
}
......@@ -1838,7 +1841,7 @@ static void bnx2x_dcbx_fw_struct(struct bnx2x *bp,
void bnx2x_dcbx_pmf_update(struct bnx2x *bp)
{
/* if we need to syncronize DCBX result from prev PMF
/* if we need to synchronize DCBX result from prev PMF
* read it from shmem and update bp and netdev accordingly
*/
if (SHMEM2_HAS(bp, drv_flags) &&
......@@ -1932,14 +1935,14 @@ static void bnx2x_dcbnl_set_pg_tccfg_tx(struct net_device *netdev, int prio,
return;
/**
* bw_pct ingnored - band-width percentage devision between user
* bw_pct ignored - band-width percentage devision between user
* priorities within the same group is not
* standard and hence not supported
*
* prio_type igonred - priority levels within the same group are not
* prio_type ignored - priority levels within the same group are not
* standard and hence are not supported. According
* to the standard pgid 15 is dedicated to strict
* prioirty traffic (on the port level).
* priority traffic (on the port level).
*
* up_map ignored
*/
......@@ -1984,14 +1987,14 @@ static void bnx2x_dcbnl_get_pg_tccfg_tx(struct net_device *netdev, int prio,
DP(BNX2X_MSG_DCB, "prio = %d\n", prio);
/**
* bw_pct ingnored - band-width percentage devision between user
* bw_pct ignored - band-width percentage devision between user
* priorities within the same group is not
* standard and hence not supported
*
* prio_type igonred - priority levels within the same group are not
* prio_type ignored - priority levels within the same group are not
* standard and hence are not supported. According
* to the standard pgid 15 is dedicated to strict
* prioirty traffic (on the port level).
* priority traffic (on the port level).
*
* up_map ignored
*/
......
drivers/net/ethernet/broadcom/bnx2x/bnx2x_dump.h
浏览文件 @ 16a5fd92
......@@ -13,12 +13,6 @@
* consent.
*/
/* This struct holds a signature to ensure the dump returned from the driver
* match the meta data file inserted to grc_dump.tcl
* The signature is time stamp, diag version and grc_dump version
*/
#ifndef BNX2X_DUMP_H
#define BNX2X_DUMP_H
......
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c
浏览文件 @ 16a5fd92
......@@ -320,7 +320,7 @@ static int bnx2x_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
speed = ethtool_cmd_speed(cmd);
/* If recieved a request for an unknown duplex, assume full*/
/* If received a request for an unknown duplex, assume full*/
if (cmd->duplex == DUPLEX_UNKNOWN)
cmd->duplex = DUPLEX_FULL;
......@@ -849,7 +849,7 @@ static int __bnx2x_get_preset_regs(struct bnx2x *bp, u32 *p, u32 preset)
/* Paged registers are supported in E2 & E3 only */
if (CHIP_IS_E2(bp) || CHIP_IS_E3(bp)) {
/* Read "paged" registes */
/* Read "paged" registers */
bnx2x_read_pages_regs(bp, p, preset);
}
......@@ -1154,8 +1154,8 @@ static int bnx2x_get_eeprom_len(struct net_device *dev)
return bp->common.flash_size;
}
/* Per pf misc lock must be aquired before the per port mcp lock. Otherwise, had
* we done things the other way around, if two pfs from the same port would
/* Per pf misc lock must be acquired before the per port mcp lock. Otherwise,
* had we done things the other way around, if two pfs from the same port would
* attempt to access nvram at the same time, we could run into a scenario such
* as:
* pf A takes the port lock.
......@@ -2070,7 +2070,7 @@ static int bnx2x_set_eee(struct net_device *dev, struct ethtool_eee *edata)
EEE_MODE_OVERRIDE_NVRAM |
EEE_MODE_OUTPUT_TIME;
/* Restart link to propogate changes */
/* Restart link to propagate changes */
if (netif_running(dev)) {
bnx2x_stats_handle(bp, STATS_EVENT_STOP);
bnx2x_force_link_reset(bp);
......
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
浏览文件 @ 16a5fd92
......@@ -808,8 +808,8 @@ static void bnx2x_hc_int_disable(struct bnx2x *bp)
u32 val = REG_RD(bp, addr);
/* in E1 we must use only PCI configuration space to disable
* MSI/MSIX capablility
* It's forbitten to disable IGU_PF_CONF_MSI_MSIX_EN in HC block
* MSI/MSIX capability
* It's forbidden to disable IGU_PF_CONF_MSI_MSIX_EN in HC block
*/
if (CHIP_IS_E1(bp)) {
/* Since IGU_PF_CONF_MSI_MSIX_EN still always on
......@@ -1012,7 +1012,7 @@ void bnx2x_panic_dump(struct bnx2x *bp, bool disable_int)
hc_sm_p[j].timer_value);
}
/* Indecies data */
/* Indices data */
for (j = 0; j < loop; j++) {
pr_cont("INDEX[%d] flags (0x%x) timeout (0x%x)\n", j,
hc_index_p[j].flags,
......@@ -1107,7 +1107,7 @@ void bnx2x_panic_dump(struct bnx2x *bp, bool disable_int)
* bnx2x_pf_flr_clnup() is called during nic_load in the per function HW
* initialization.
*/
#define FLR_WAIT_USEC 10000 /* 10 miliseconds */
#define FLR_WAIT_USEC 10000 /* 10 milliseconds */
#define FLR_WAIT_INTERVAL 50 /* usec */
#define FLR_POLL_CNT (FLR_WAIT_USEC/FLR_WAIT_INTERVAL) /* 200 */
......@@ -1327,7 +1327,7 @@ int bnx2x_send_final_clnup(struct bnx2x *bp, u8 clnup_func, u32 poll_cnt)
bnx2x_panic();
return 1;
}
/* Zero completion for nxt FLR */
/* Zero completion for next FLR */
REG_WR(bp, comp_addr, 0);
return ret;
......@@ -2343,7 +2343,7 @@ u8 bnx2x_link_test(struct bnx2x *bp, u8 is_serdes)
sum of vn_min_rates.
or
0 - if all the min_rates are 0.
In the later case fainess algorithm should be deactivated.
In the later case fairness algorithm should be deactivated.
If not all min_rates are zero then those that are zeroes will be set to 1.
*/
static void bnx2x_calc_vn_min(struct bnx2x *bp,
......@@ -2423,7 +2423,7 @@ void bnx2x_read_mf_cfg(struct bnx2x *bp)
int vn, n = (CHIP_MODE_IS_4_PORT(bp) ? 2 : 1);
if (BP_NOMCP(bp))
return; /* what should be the default bvalue in this case */
return; /* what should be the default value in this case */
/* For 2 port configuration the absolute function number formula
* is:
......@@ -2922,7 +2922,7 @@ void bnx2x_func_init(struct bnx2x *bp, struct bnx2x_func_init_params *p)
}
/**
* bnx2x_get_tx_only_flags - Return common flags
* bnx2x_get_common_flags - Return common flags
*
* @bp device handle
* @fp queue handle
......@@ -3110,7 +3110,7 @@ static void bnx2x_pf_tx_q_prep(struct bnx2x *bp,
txq_init->fw_sb_id = fp->fw_sb_id;
/*
* set the tss leading client id for TX classfication ==
* set the tss leading client id for TX classification ==
* leading RSS client id
*/
txq_init->tss_leading_cl_id = bnx2x_fp(bp, 0, cl_id);
......@@ -3197,7 +3197,7 @@ static void bnx2x_e1h_enable(struct bnx2x *bp)
REG_WR(bp, NIG_REG_LLH0_FUNC_EN + port*8, 1);
/* Tx queue should be only reenabled */
/* Tx queue should be only re-enabled */
netif_tx_wake_all_queues(bp->dev);
/*
......@@ -3591,7 +3591,7 @@ int bnx2x_sp_post(struct bnx2x *bp, int command, int cid,
/*
* It's ok if the actual decrement is issued towards the memory
* somewhere between the spin_lock and spin_unlock. Thus no
* more explict memory barrier is needed.
* more explicit memory barrier is needed.
*/
if (common)
atomic_dec(&bp->eq_spq_left);
......@@ -3660,7 +3660,7 @@ static u16 bnx2x_update_dsb_idx(struct bnx2x *bp)
rc |= BNX2X_DEF_SB_IDX;
}
/* Do not reorder: indecies reading should complete before handling */
/* Do not reorder: indices reading should complete before handling */
barrier();
return rc;
}
......@@ -3809,8 +3809,7 @@ static void bnx2x_fan_failure(struct bnx2x *bp)
netdev_err(bp->dev, "Fan Failure on Network Controller has caused the driver to shutdown the card to prevent permanent damage.\n"
"Please contact OEM Support for assistance\n");
/*
* Schedule device reset (unload)
/* Schedule device reset (unload)
* This is due to some boards consuming sufficient power when driver is
* up to overheat if fan fails.
*/
......@@ -4987,7 +4986,7 @@ static void bnx2x_eq_int(struct bnx2x *bp)
hw_cons = le16_to_cpu(*bp->eq_cons_sb);
/* The hw_cos range is 1-255, 257 - the sw_cons range is 0-254, 256.
* when we get the the next-page we nned to adjust so the loop
* when we get the next-page we need to adjust so the loop
* condition below will be met. The next element is the size of a
* regular element and hence incrementing by 1
*/
......@@ -5194,7 +5193,7 @@ static void bnx2x_sp_task(struct work_struct *work)
DP(BNX2X_MSG_SP, "sp task invoked\n");
/* make sure the atomic interupt_occurred has been written */
/* make sure the atomic interrupt_occurred has been written */
smp_rmb();
if (atomic_read(&bp->interrupt_occurred)) {
......@@ -5670,7 +5669,7 @@ static void bnx2x_init_eq_ring(struct bnx2x *bp)
bp->eq_cons = 0;
bp->eq_prod = NUM_EQ_DESC;
bp->eq_cons_sb = BNX2X_EQ_INDEX;
/* we want a warning message before it gets rought... */
/* we want a warning message before it gets wrought... */
atomic_set(&bp->eq_spq_left,
min_t(int, MAX_SP_DESC_CNT - MAX_SPQ_PENDING, NUM_EQ_DESC) - 1);
}
......@@ -5754,7 +5753,7 @@ static int bnx2x_fill_accept_flags(struct bnx2x *bp, u32 rx_mode,
break;
case BNX2X_RX_MODE_PROMISC:
/* According to deffinition of SI mode, iface in promisc mode
/* According to definition of SI mode, iface in promisc mode
* should receive matched and unmatched (in resolution of port)
* unicast packets.
*/
......@@ -5897,7 +5896,7 @@ static void bnx2x_init_eth_fp(struct bnx2x *bp, int fp_idx)
/* init shortcut */
fp->ustorm_rx_prods_offset = bnx2x_rx_ustorm_prods_offset(fp);
/* Setup SB indicies */
/* Setup SB indices */
fp->rx_cons_sb = BNX2X_RX_SB_INDEX;
/* Configure Queue State object */
......@@ -6652,7 +6651,7 @@ static int bnx2x_init_hw_common(struct bnx2x *bp)
* stay set)
* f. If this is VNIC 3 of a port then also init
* first_timers_ilt_entry to zero and last_timers_ilt_entry
* to the last enrty in the ILT.
* to the last entry in the ILT.
*
* Notes:
* Currently the PF error in the PGLC is non recoverable.
......@@ -7118,8 +7117,8 @@ static int bnx2x_init_hw_port(struct bnx2x *bp)
bnx2x_init_block(bp, BLOCK_MISC_AEU, init_phase);
/* init aeu_mask_attn_func_0/1:
* - SF mode: bits 3-7 are masked. only bits 0-2 are in use
* - MF mode: bit 3 is masked. bits 0-2 are in use as in SF
* - SF mode: bits 3-7 are masked. Only bits 0-2 are in use
* - MF mode: bit 3 is masked. Bits 0-2 are in use as in SF
* bits 4-7 are used for "per vn group attention" */
val = IS_MF(bp) ? 0xF7 : 0x7;
/* Enable DCBX attention for all but E1 */
......@@ -7371,7 +7370,7 @@ int bnx2x_init_hw_func_cnic(struct bnx2x *bp)
bnx2x_ilt_init_op_cnic(bp, INITOP_SET);
if (CONFIGURE_NIC_MODE(bp)) {
/* Configrue searcher as part of function hw init */
/* Configure searcher as part of function hw init */
bnx2x_init_searcher(bp);
/* Reset NIC mode */
......@@ -7641,7 +7640,7 @@ static int bnx2x_init_hw_func(struct bnx2x *bp)
}
bnx2x_igu_clear_sb(bp, bp->igu_dsb_id);
/* !!! these should become driver const once
/* !!! These should become driver const once
rf-tool supports split-68 const */
REG_WR(bp, IGU_REG_SB_INT_BEFORE_MASK_LSB, 0);
REG_WR(bp, IGU_REG_SB_INT_BEFORE_MASK_MSB, 0);
......@@ -7755,7 +7754,7 @@ int bnx2x_alloc_mem_cnic(struct bnx2x *bp)
host_hc_status_block_e1x));
if (CONFIGURE_NIC_MODE(bp) && !bp->t2)
/* allocate searcher T2 table, as it wan't allocated before */
/* allocate searcher T2 table, as it wasn't allocated before */
BNX2X_PCI_ALLOC(bp->t2, &bp->t2_mapping, SRC_T2_SZ);
/* write address to which L5 should insert its values */
......@@ -8093,7 +8092,7 @@ static void bnx2x_pf_q_prep_init(struct bnx2x *bp,
__set_bit(BNX2X_Q_FLG_HC, &init_params->rx.flags);
__set_bit(BNX2X_Q_FLG_HC, &init_params->tx.flags);
/* If HC is supporterd, enable host coalescing in the transition
/* If HC is supported, enable host coalescing in the transition
* to INIT state.
*/
__set_bit(BNX2X_Q_FLG_HC_EN, &init_params->rx.flags);
......@@ -8579,14 +8578,14 @@ static int bnx2x_func_wait_started(struct bnx2x *bp)
/*
* (assumption: No Attention from MCP at this stage)
* PMF probably in the middle of TXdisable/enable transaction
* PMF probably in the middle of TX disable/enable transaction
* 1. Sync IRS for default SB
* 2. Sync SP queue - this guarantes us that attention handling started
* 3. Wait, that TXdisable/enable transaction completes
* 2. Sync SP queue - this guarantees us that attention handling started
* 3. Wait, that TX disable/enable transaction completes
*
* 1+2 guranty that if DCBx attention was scheduled it already changed
* pending bit of transaction from STARTED-->TX_STOPPED, if we alredy
* received complettion for the transaction the state is TX_STOPPED.
* 1+2 guarantee that if DCBx attention was scheduled it already changed
* pending bit of transaction from STARTED-->TX_STOPPED, if we already
* received completion for the transaction the state is TX_STOPPED.
* State will return to STARTED after completion of TX_STOPPED-->STARTED
* transaction.
*/
......@@ -8705,7 +8704,7 @@ void bnx2x_chip_cleanup(struct bnx2x *bp, int unload_mode, bool keep_link)
/*
* (assumption: No Attention from MCP at this stage)
* PMF probably in the middle of TXdisable/enable transaction
* PMF probably in the middle of TX disable/enable transaction
*/
rc = bnx2x_func_wait_started(bp);
if (rc) {
......@@ -9320,7 +9319,7 @@ static void bnx2x_parity_recover(struct bnx2x *bp)
* the first leader that performs a
* leader_reset() reset the global blocks in
* order to clear global attentions. Otherwise
* the the gates will remain closed for that
* the gates will remain closed for that
* engine.
*/
if (load_status ||
......@@ -10056,7 +10055,7 @@ static int bnx2x_prev_unload(struct bnx2x *bp)
break;
}
/* non-common reply from MCP night require looping */
/* non-common reply from MCP might require looping */
rc = bnx2x_prev_unload_uncommon(bp);
if (rc != BNX2X_PREV_WAIT_NEEDED)
break;
......@@ -11034,7 +11033,7 @@ static int bnx2x_get_hwinfo(struct bnx2x *bp)
} else {
bp->common.int_block = INT_BLOCK_IGU;
/* do not allow device reset during IGU info preocessing */
/* do not allow device reset during IGU info processing */
bnx2x_acquire_hw_lock(bp, HW_LOCK_RESOURCE_RESET);
val = REG_RD(bp, IGU_REG_BLOCK_CONFIGURATION);
......@@ -11113,7 +11112,7 @@ static int bnx2x_get_hwinfo(struct bnx2x *bp)
E1H_FUNC_MAX * sizeof(struct drv_func_mb);
/*
* get mf configuration:
* 1. existence of MF configuration
* 1. Existence of MF configuration
* 2. MAC address must be legal (check only upper bytes)
* for Switch-Independent mode;
* OVLAN must be legal for Switch-Dependent mode
......@@ -11490,7 +11489,7 @@ static int bnx2x_init_bp(struct bnx2x *bp)
/* We need at least one default status block for slow-path events,
* second status block for the L2 queue, and a third status block for
* CNIC if supproted.
* CNIC if supported.
*/
if (CNIC_SUPPORT(bp))
bp->min_msix_vec_cnt = 3;
......@@ -12874,7 +12873,7 @@ static pci_ers_result_t bnx2x_io_slot_reset(struct pci_dev *pdev)
bnx2x_prev_unload(bp);
/* We should have resetted the engine, so It's fair to
/* We should have reseted the engine, so It's fair to
* assume the FW will no longer write to the bnx2x driver.
*/
bnx2x_squeeze_objects(bp);
......@@ -12993,7 +12992,7 @@ static void __exit bnx2x_cleanup(void)
destroy_workqueue(bnx2x_wq);
/* Free globablly allocated resources */
/* Free globally allocated resources */
list_for_each_safe(pos, q, &bnx2x_prev_list) {
struct bnx2x_prev_path_list *tmp =
list_entry(pos, struct bnx2x_prev_path_list, list);
......@@ -13016,7 +13015,7 @@ module_exit(bnx2x_cleanup);
* @bp: driver handle
* @set: set or clear the CAM entry
*
* This function will wait until the ramdord completion returns.
* This function will wait until the ramrod completion returns.
* Return 0 if success, -ENODEV if ramrod doesn't return.
*/
static int bnx2x_set_iscsi_eth_mac_addr(struct bnx2x *bp)
......
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c
浏览文件 @ 16a5fd92
......@@ -35,9 +35,9 @@
/**
* bnx2x_exe_queue_init - init the Exe Queue object
*
* @o: poiter to the object
* @o: pointer to the object
* @exe_len: length
* @owner: poiter to the owner
* @owner: pointer to the owner
* @validate: validate function pointer
* @optimize: optimize function pointer
* @exec: execute function pointer
......@@ -176,7 +176,7 @@ static inline void bnx2x_exe_queue_reset_pending(struct bnx2x *bp,
* @o: queue
* @ramrod_flags: flags
*
* (Atomicy is ensured using the exe_queue->lock).
* (Atomicity is ensured using the exe_queue->lock).
*/
static inline int bnx2x_exe_queue_step(struct bnx2x *bp,
struct bnx2x_exe_queue_obj *o,
......@@ -189,8 +189,7 @@ static inline int bnx2x_exe_queue_step(struct bnx2x *bp,
spin_lock_bh(&o->lock);
/*
* Next step should not be performed until the current is finished,
/* Next step should not be performed until the current is finished,
* unless a DRV_CLEAR_ONLY bit is set. In this case we just want to
* properly clear object internals without sending any command to the FW
* which also implies there won't be any completion to clear the
......@@ -206,8 +205,7 @@ static inline int bnx2x_exe_queue_step(struct bnx2x *bp,
}
}
/*
* Run through the pending commands list and create a next
/* Run through the pending commands list and create a next
* execution chunk.
*/
while (!list_empty(&o->exe_queue)) {
......@@ -217,8 +215,7 @@ static inline int bnx2x_exe_queue_step(struct bnx2x *bp,
if (cur_len + elem->cmd_len <= o->exe_chunk_len) {
cur_len += elem->cmd_len;
/*
* Prevent from both lists being empty when moving an
/* Prevent from both lists being empty when moving an
* element. This will allow the call of
* bnx2x_exe_queue_empty() without locking.
*/
......@@ -238,14 +235,12 @@ static inline int bnx2x_exe_queue_step(struct bnx2x *bp,
rc = o->execute(bp, o->owner, &o->pending_comp, ramrod_flags);
if (rc < 0)
/*
* In case of an error return the commands back to the queue
/* In case of an error return the commands back to the queue
* and reset the pending_comp.
*/
list_splice_init(&o->pending_comp, &o->exe_queue);
else if (!rc)
/*
* If zero is returned, means there are no outstanding pending
/* If zero is returned, means there are no outstanding pending
* completions and we may dismiss the pending list.
*/
__bnx2x_exe_queue_reset_pending(bp, o);
......@@ -685,7 +680,7 @@ static inline void bnx2x_vlan_mac_set_cmd_hdr_e2(struct bnx2x *bp,
*
* @cid: connection id
* @type: BNX2X_FILTER_XXX_PENDING
* @hdr: poiter to header to setup
* @hdr: pointer to header to setup
* @rule_cnt:
*
* currently we always configure one rule and echo field to contain a CID and an
......@@ -714,8 +709,7 @@ static void bnx2x_set_one_mac_e2(struct bnx2x *bp,
unsigned long *vlan_mac_flags = &elem->cmd_data.vlan_mac.vlan_mac_flags;
u8 *mac = elem->cmd_data.vlan_mac.u.mac.mac;
/*
* Set LLH CAM entry: currently only iSCSI and ETH macs are
/* Set LLH CAM entry: currently only iSCSI and ETH macs are
* relevant. In addition, current implementation is tuned for a
* single ETH MAC.
*
......@@ -870,8 +864,7 @@ static void bnx2x_set_one_mac_e1x(struct bnx2x *bp,
struct bnx2x_raw_obj *raw = &o->raw;
struct mac_configuration_cmd *config =
(struct mac_configuration_cmd *)(raw->rdata);
/*
* 57710 and 57711 do not support MOVE command,
/* 57710 and 57711 do not support MOVE command,
* so it's either ADD or DEL
*/
bool add = (elem->cmd_data.vlan_mac.cmd == BNX2X_VLAN_MAC_ADD) ?
......@@ -959,7 +952,7 @@ static void bnx2x_set_one_vlan_mac_e2(struct bnx2x *bp,
bnx2x_vlan_mac_set_cmd_hdr_e2(bp, o, add, CLASSIFY_RULE_OPCODE_PAIR,
&rule_entry->pair.header);
/* Set VLAN and MAC themselvs */
/* Set VLAN and MAC themselves */
rule_entry->pair.vlan = cpu_to_le16(vlan);
bnx2x_set_fw_mac_addr(&rule_entry->pair.mac_msb,
&rule_entry->pair.mac_mid,
......@@ -1011,8 +1004,7 @@ static void bnx2x_set_one_vlan_mac_e1h(struct bnx2x *bp,
struct bnx2x_raw_obj *raw = &o->raw;
struct mac_configuration_cmd *config =
(struct mac_configuration_cmd *)(raw->rdata);
/*
* 57710 and 57711 do not support MOVE command,
/* 57710 and 57711 do not support MOVE command,
* so it's either ADD or DEL
*/
bool add = (elem->cmd_data.vlan_mac.cmd == BNX2X_VLAN_MAC_ADD) ?
......@@ -1036,7 +1028,7 @@ static void bnx2x_set_one_vlan_mac_e1h(struct bnx2x *bp,
*
* @bp: device handle
* @p: command parameters
* @ppos: pointer to the cooky
* @ppos: pointer to the cookie
*
* reconfigure next MAC/VLAN/VLAN-MAC element from the
* previously configured elements list.
......@@ -1044,7 +1036,7 @@ static void bnx2x_set_one_vlan_mac_e1h(struct bnx2x *bp,
* from command parameters only RAMROD_COMP_WAIT bit in ramrod_flags is taken
* into an account
*
* pointer to the cooky - that should be given back in the next call to make
* pointer to the cookie - that should be given back in the next call to make
* function handle the next element. If *ppos is set to NULL it will restart the
* iterator. If returned *ppos == NULL this means that the last element has been
* handled.
......@@ -1092,8 +1084,7 @@ static int bnx2x_vlan_mac_restore(struct bnx2x *bp,
return bnx2x_config_vlan_mac(bp, p);
}
/*
* bnx2x_exeq_get_mac/bnx2x_exeq_get_vlan/bnx2x_exeq_get_vlan_mac return a
/* bnx2x_exeq_get_mac/bnx2x_exeq_get_vlan/bnx2x_exeq_get_vlan_mac return a
* pointer to an element with a specific criteria and NULL if such an element
* hasn't been found.
*/
......@@ -1177,8 +1168,7 @@ static inline int bnx2x_validate_vlan_mac_add(struct bnx2x *bp,
return rc;
}
/*
* Check if there is a pending ADD command for this
/* Check if there is a pending ADD command for this
* MAC/VLAN/VLAN-MAC. Return an error if there is.
*/
if (exeq->get(exeq, elem)) {
......@@ -1186,8 +1176,7 @@ static inline int bnx2x_validate_vlan_mac_add(struct bnx2x *bp,
return -EEXIST;
}
/*
* TODO: Check the pending MOVE from other objects where this
/* TODO: Check the pending MOVE from other objects where this
* object is a destination object.
*/
......@@ -1230,8 +1219,7 @@ static inline int bnx2x_validate_vlan_mac_del(struct bnx2x *bp,
return -EEXIST;
}
/*
* Check if there are pending DEL or MOVE commands for this
/* Check if there are pending DEL or MOVE commands for this
* MAC/VLAN/VLAN-MAC. Return an error if so.
*/
memcpy(&query_elem, elem, sizeof(query_elem));
......@@ -1282,8 +1270,7 @@ static inline int bnx2x_validate_vlan_mac_move(struct bnx2x *bp,
struct bnx2x_exe_queue_obj *src_exeq = &src_o->exe_queue;
struct bnx2x_exe_queue_obj *dest_exeq = &dest_o->exe_queue;
/*
* Check if we can perform this operation based on the current registry
/* Check if we can perform this operation based on the current registry
* state.
*/
if (!src_o->check_move(bp, src_o, dest_o,
......@@ -1292,8 +1279,7 @@ static inline int bnx2x_validate_vlan_mac_move(struct bnx2x *bp,
return -EINVAL;
}
/*
* Check if there is an already pending DEL or MOVE command for the
/* Check if there is an already pending DEL or MOVE command for the
* source object or ADD command for a destination object. Return an
* error if so.
*/
......@@ -1382,7 +1368,7 @@ static int bnx2x_remove_vlan_mac(struct bnx2x *bp,
}
/**
* bnx2x_wait_vlan_mac - passivly wait for 5 seconds until all work completes.
* bnx2x_wait_vlan_mac - passively wait for 5 seconds until all work completes.
*
* @bp: device handle
* @o: bnx2x_vlan_mac_obj
......@@ -1540,9 +1526,8 @@ static inline int bnx2x_vlan_mac_get_registry_elem(
/* Get a new CAM offset */
if (!o->get_cam_offset(o, &reg_elem->cam_offset)) {
/*
* This shell never happen, because we have checked the
* CAM availiability in the 'validate'.
/* This shall never happen, because we have checked the
* CAM availability in the 'validate'.
*/
WARN_ON(1);
kfree(reg_elem);
......@@ -1589,8 +1574,7 @@ static int bnx2x_execute_vlan_mac(struct bnx2x *bp,
struct bnx2x_vlan_mac_registry_elem *reg_elem;
enum bnx2x_vlan_mac_cmd cmd;
/*
* If DRIVER_ONLY execution is requested, cleanup a registry
/* If DRIVER_ONLY execution is requested, cleanup a registry
* and exit. Otherwise send a ramrod to FW.
*/
if (!drv_only) {
......@@ -1599,11 +1583,10 @@ static int bnx2x_execute_vlan_mac(struct bnx2x *bp,
/* Set pending */
r->set_pending(r);
/* Fill tha ramrod data */
/* Fill the ramrod data */
list_for_each_entry(elem, exe_chunk, link) {
cmd = elem->cmd_data.vlan_mac.cmd;
/*
* We will add to the target object in MOVE command, so
/* We will add to the target object in MOVE command, so
* change the object for a CAM search.
*/
if (cmd == BNX2X_VLAN_MAC_MOVE)
......@@ -1636,8 +1619,7 @@ static int bnx2x_execute_vlan_mac(struct bnx2x *bp,
idx++;
}
/*
* No need for an explicit memory barrier here as long we would
/* No need for an explicit memory barrier here as long we would
* need to ensure the ordering of writing to the SPQ element
* and updating of the SPQ producer which involves a memory
* read and we will have to put a full memory barrier there
......@@ -1756,8 +1738,7 @@ int bnx2x_config_vlan_mac(
return rc;
}
/*
* If nothing will be executed further in this iteration we want to
/* If nothing will be executed further in this iteration we want to
* return PENDING if there are pending commands
*/
if (!bnx2x_exe_queue_empty(&o->exe_queue))
......@@ -1776,13 +1757,11 @@ int bnx2x_config_vlan_mac(
return rc;
}
/*
* RAMROD_COMP_WAIT is a superset of RAMROD_EXEC. If it was set
/* RAMROD_COMP_WAIT is a superset of RAMROD_EXEC. If it was set
* then user want to wait until the last command is done.
*/
if (test_bit(RAMROD_COMP_WAIT, &p->ramrod_flags)) {
/*
* Wait maximum for the current exe_queue length iterations plus
/* Wait maximum for the current exe_queue length iterations plus
* one (for the current pending command).
*/
int max_iterations = bnx2x_exe_queue_length(&o->exe_queue) + 1;
......@@ -1817,7 +1796,7 @@ int bnx2x_config_vlan_mac(
* @ramrod_flags: execution flags to be used for this deletion
*
* if the last operation has completed successfully and there are no
* moreelements left, positive value if the last operation has completed
* more elements left, positive value if the last operation has completed
* successfully and there are more previously configured elements, negative
* value is current operation has failed.
*/
......@@ -1858,8 +1837,7 @@ static int bnx2x_vlan_mac_del_all(struct bnx2x *bp,
p.ramrod_flags = *ramrod_flags;
p.user_req.cmd = BNX2X_VLAN_MAC_DEL;
/*
* Add all but the last VLAN-MAC to the execution queue without actually
/* Add all but the last VLAN-MAC to the execution queue without actually
* execution anything.
*/
__clear_bit(RAMROD_COMP_WAIT, &p.ramrod_flags);
......@@ -2035,8 +2013,7 @@ void bnx2x_init_vlan_mac_obj(struct bnx2x *bp,
/* CAM pool handling */
vlan_mac_obj->get_credit = bnx2x_get_credit_vlan_mac;
vlan_mac_obj->put_credit = bnx2x_put_credit_vlan_mac;
/*
* CAM offset is relevant for 57710 and 57711 chips only which have a
/* CAM offset is relevant for 57710 and 57711 chips only which have a
* single CAM for both MACs and VLAN-MAC pairs. So the offset
* will be taken from MACs' pool object only.
*/
......@@ -2103,12 +2080,12 @@ static int bnx2x_set_rx_mode_e1x(struct bnx2x *bp,
struct tstorm_eth_mac_filter_config *mac_filters =
(struct tstorm_eth_mac_filter_config *)p->rdata;
/* initial seeting is drop-all */
/* initial setting is drop-all */
u8 drop_all_ucast = 1, drop_all_mcast = 1;
u8 accp_all_ucast = 0, accp_all_bcast = 0, accp_all_mcast = 0;
u8 unmatched_unicast = 0;
/* In e1x there we only take into account rx acceot flag since tx switching
/* In e1x there we only take into account rx accept flag since tx switching
* isn't enabled. */
if (test_bit(BNX2X_ACCEPT_UNICAST, &p->rx_accept_flags))
/* accept matched ucast */
......@@ -2271,8 +2248,7 @@ static int bnx2x_set_rx_mode_e2(struct bnx2x *bp,
false);
}
/*
* If FCoE Queue configuration has been requested configure the Rx and
/* If FCoE Queue configuration has been requested configure the Rx and
* internal switching modes for this queue in separate rules.
*
* FCoE queue shell never be set to ACCEPT_ALL packets of any sort:
......@@ -2308,8 +2284,7 @@ static int bnx2x_set_rx_mode_e2(struct bnx2x *bp,
}
}
/*
* Set the ramrod header (most importantly - number of rules to
/* Set the ramrod header (most importantly - number of rules to
* configure).
*/
bnx2x_rx_mode_set_rdata_hdr_e2(p->cid, &data->header, rule_idx);
......@@ -2318,8 +2293,7 @@ static int bnx2x_set_rx_mode_e2(struct bnx2x *bp,
data->header.rule_cnt, p->rx_accept_flags,
p->tx_accept_flags);
/*
* No need for an explicit memory barrier here as long we would
/* No need for an explicit memory barrier here as long we would
* need to ensure the ordering of writing to the SPQ element
* and updating of the SPQ producer which involves a memory
* read and we will have to put a full memory barrier there
......@@ -2460,7 +2434,7 @@ static int bnx2x_mcast_enqueue_cmd(struct bnx2x *bp,
cur_mac = (struct bnx2x_mcast_mac_elem *)
((u8 *)new_cmd + sizeof(*new_cmd));
/* Push the MACs of the current command into the pendig command
/* Push the MACs of the current command into the pending command
* MACs list: FIFO
*/
list_for_each_entry(pos, &p->mcast_list, link) {
......@@ -3017,16 +2991,14 @@ static int bnx2x_mcast_setup_e2(struct bnx2x *bp,
if (!o->total_pending_num)
bnx2x_mcast_refresh_registry_e2(bp, o);
/*
* If CLEAR_ONLY was requested - don't send a ramrod and clear
/* If CLEAR_ONLY was requested - don't send a ramrod and clear
* RAMROD_PENDING status immediately.
*/
if (test_bit(RAMROD_DRV_CLR_ONLY, &p->ramrod_flags)) {
raw->clear_pending(raw);
return 0;
} else {
/*
* No need for an explicit memory barrier here as long we would
/* No need for an explicit memory barrier here as long we would
* need to ensure the ordering of writing to the SPQ element
* and updating of the SPQ producer which involves a memory
* read and we will have to put a full memory barrier there
......@@ -3104,7 +3076,7 @@ static inline void bnx2x_mcast_hdl_restore_e1h(struct bnx2x *bp,
}
}
/* On 57711 we write the multicast MACs' aproximate match
/* On 57711 we write the multicast MACs' approximate match
* table by directly into the TSTORM's internal RAM. So we don't
* really need to handle any tricks to make it work.
*/
......@@ -3227,7 +3199,7 @@ static void bnx2x_mcast_revert_e1(struct bnx2x *bp,
/* If current command hasn't been handled yet and we are
* here means that it's meant to be dropped and we have to
* update the number of outstandling MACs accordingly.
* update the number of outstanding MACs accordingly.
*/
if (p->mcast_list_len)
o->total_pending_num -= o->max_cmd_len;
......@@ -3503,16 +3475,14 @@ static int bnx2x_mcast_setup_e1(struct bnx2x *bp,
if (rc)
return rc;
/*
* If CLEAR_ONLY was requested - don't send a ramrod and clear
/* If CLEAR_ONLY was requested - don't send a ramrod and clear
* RAMROD_PENDING status immediately.
*/
if (test_bit(RAMROD_DRV_CLR_ONLY, &p->ramrod_flags)) {
raw->clear_pending(raw);
return 0;
} else {
/*
* No need for an explicit memory barrier here as long we would
/* No need for an explicit memory barrier here as long we would
* need to ensure the ordering of writing to the SPQ element
* and updating of the SPQ producer which involves a memory
* read and we will have to put a full memory barrier there
......@@ -3977,8 +3947,7 @@ void bnx2x_init_mac_credit_pool(struct bnx2x *bp,
} else {
/*
* CAM credit is equaly divided between all active functions
/* CAM credit is equaly divided between all active functions
* on the PATH.
*/
if ((func_num > 0)) {
......@@ -3987,8 +3956,7 @@ void bnx2x_init_mac_credit_pool(struct bnx2x *bp,
else
cam_sz = BNX2X_CAM_SIZE_EMUL;
/*
* No need for CAM entries handling for 57712 and
/* No need for CAM entries handling for 57712 and
* newer.
*/
bnx2x_init_credit_pool(p, -1, cam_sz);
......@@ -4005,14 +3973,12 @@ void bnx2x_init_vlan_credit_pool(struct bnx2x *bp,
u8 func_num)
{
if (CHIP_IS_E1x(bp)) {
/*
* There is no VLAN credit in HW on 57710 and 57711 only
/* There is no VLAN credit in HW on 57710 and 57711 only
* MAC / MAC-VLAN can be set
*/
bnx2x_init_credit_pool(p, 0, -1);
} else {
/*
* CAM credit is equaly divided between all active functions
/* CAM credit is equally divided between all active functions
* on the PATH.
*/
if (func_num > 0) {
......@@ -4028,7 +3994,7 @@ void bnx2x_init_vlan_credit_pool(struct bnx2x *bp,
/**
* bnx2x_debug_print_ind_table - prints the indirection table configuration.
*
* @bp: driver hanlde
* @bp: driver handle
* @p: pointer to rss configuration
*
* Prints it when NETIF_MSG_IFUP debug level is configured.
......@@ -4141,8 +4107,7 @@ static int bnx2x_setup_rss(struct bnx2x *bp,
data->capabilities |= ETH_RSS_UPDATE_RAMROD_DATA_UPDATE_RSS_KEY;
}
/*
* No need for an explicit memory barrier here as long we would
/* No need for an explicit memory barrier here as long we would
* need to ensure the ordering of writing to the SPQ element
* and updating of the SPQ producer which involves a memory
* read and we will have to put a full memory barrier there
......@@ -4312,7 +4277,7 @@ static int bnx2x_queue_comp_cmd(struct bnx2x *bp,
}
if (o->next_tx_only >= o->max_cos)
/* >= becuase tx only must always be smaller than cos since the
/* >= because tx only must always be smaller than cos since the
* primary connection supports COS 0
*/
BNX2X_ERR("illegal value for next tx_only: %d. max cos was %d",
......@@ -4625,8 +4590,7 @@ static inline int bnx2x_q_send_setup_e1x(struct bnx2x *bp,
/* Fill the ramrod data */
bnx2x_q_fill_setup_data_cmn(bp, params, rdata);
/*
* No need for an explicit memory barrier here as long we would
/* No need for an explicit memory barrier here as long we would
* need to ensure the ordering of writing to the SPQ element
* and updating of the SPQ producer which involves a memory
* read and we will have to put a full memory barrier there
......@@ -4654,8 +4618,7 @@ static inline int bnx2x_q_send_setup_e2(struct bnx2x *bp,
bnx2x_q_fill_setup_data_cmn(bp, params, rdata);
bnx2x_q_fill_setup_data_e2(bp, params, rdata);
/*
* No need for an explicit memory barrier here as long we would
/* No need for an explicit memory barrier here as long we would
* need to ensure the ordering of writing to the SPQ element
* and updating of the SPQ producer which involves a memory
* read and we will have to put a full memory barrier there
......@@ -4699,8 +4662,7 @@ static inline int bnx2x_q_send_setup_tx_only(struct bnx2x *bp,
o->cids[cid_index], rdata->general.client_id,
rdata->general.sp_client_id, rdata->general.cos);
/*
* No need for an explicit memory barrier here as long we would
/* No need for an explicit memory barrier here as long we would
* need to ensure the ordering of writing to the SPQ element
* and updating of the SPQ producer which involves a memory
* read and we will have to put a full memory barrier there
......@@ -4733,7 +4695,7 @@ static void bnx2x_q_fill_update_data(struct bnx2x *bp,
test_bit(BNX2X_Q_UPDATE_IN_VLAN_REM_CHNG,
&params->update_flags);
/* Outer VLAN sripping */
/* Outer VLAN stripping */
data->outer_vlan_removal_enable_flg =
test_bit(BNX2X_Q_UPDATE_OUT_VLAN_REM, &params->update_flags);
data->outer_vlan_removal_change_flg =
......@@ -4794,8 +4756,7 @@ static inline int bnx2x_q_send_update(struct bnx2x *bp,
/* Fill the ramrod data */
bnx2x_q_fill_update_data(bp, o, update_params, rdata);
/*
* No need for an explicit memory barrier here as long we would
/* No need for an explicit memory barrier here as long we would
* need to ensure the ordering of writing to the SPQ element
* and updating of the SPQ producer which involves a memory
* read and we will have to put a full memory barrier there
......@@ -5009,8 +4970,7 @@ static int bnx2x_queue_chk_transition(struct bnx2x *bp,
&params->params.update;
u8 next_tx_only = o->num_tx_only;
/*
* Forget all pending for completion commands if a driver only state
/* Forget all pending for completion commands if a driver only state
* transition has been requested.
*/
if (test_bit(RAMROD_DRV_CLR_ONLY, &params->ramrod_flags)) {
......@@ -5018,8 +4978,7 @@ static int bnx2x_queue_chk_transition(struct bnx2x *bp,
o->next_state = BNX2X_Q_STATE_MAX;
}
/*
* Don't allow a next state transition if we are in the middle of
/* Don't allow a next state transition if we are in the middle of
* the previous one.
*/
if (o->pending) {
......@@ -5228,8 +5187,7 @@ enum bnx2x_func_state bnx2x_func_get_state(struct bnx2x *bp,
if (o->pending)
return BNX2X_F_STATE_MAX;
/*
* unsure the order of reading of o->pending and o->state
/* unsure the order of reading of o->pending and o->state
* o->pending should be read first
*/
rmb();
......@@ -5327,8 +5285,7 @@ static int bnx2x_func_chk_transition(struct bnx2x *bp,
enum bnx2x_func_state state = o->state, next_state = BNX2X_F_STATE_MAX;
enum bnx2x_func_cmd cmd = params->cmd;
/*
* Forget all pending for completion commands if a driver only state
/* Forget all pending for completion commands if a driver only state
* transition has been requested.
*/
if (test_bit(RAMROD_DRV_CLR_ONLY, &params->ramrod_flags)) {
......@@ -5336,8 +5293,7 @@ static int bnx2x_func_chk_transition(struct bnx2x *bp,
o->next_state = BNX2X_F_STATE_MAX;
}
/*
* Don't allow a next state transition if we are in the middle of
/* Don't allow a next state transition if we are in the middle of
* the previous one.
*/
if (o->pending)
......@@ -5510,7 +5466,7 @@ static int bnx2x_func_hw_init(struct bnx2x *bp,
goto init_err;
}
/* Handle the beginning of COMMON_XXX pases separatelly... */
/* Handle the beginning of COMMON_XXX pases separately... */
switch (load_code) {
case FW_MSG_CODE_DRV_LOAD_COMMON_CHIP:
rc = bnx2x_func_init_cmn_chip(bp, drv);
......@@ -5544,7 +5500,7 @@ static int bnx2x_func_hw_init(struct bnx2x *bp,
init_err:
drv->gunzip_end(bp);
/* In case of success, complete the comand immediatelly: no ramrods
/* In case of success, complete the command immediately: no ramrods
* have been sent.
*/
if (!rc)
......@@ -5569,7 +5525,7 @@ static inline void bnx2x_func_reset_func(struct bnx2x *bp,
}
/**
* bnx2x_func_reset_port - reser HW at port stage
* bnx2x_func_reset_port - reset HW at port stage
*
* @bp: device handle
* @drv:
......@@ -5591,7 +5547,7 @@ static inline void bnx2x_func_reset_port(struct bnx2x *bp,
}
/**
* bnx2x_func_reset_cmn - reser HW at common stage
* bnx2x_func_reset_cmn - reset HW at common stage
*
* @bp: device handle
* @drv:
......@@ -5633,7 +5589,7 @@ static inline int bnx2x_func_hw_reset(struct bnx2x *bp,
break;
}
/* Complete the comand immediatelly: no ramrods have been sent. */
/* Complete the command immediately: no ramrods have been sent. */
o->complete_cmd(bp, o, BNX2X_F_CMD_HW_RESET);
return 0;
......
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.h
浏览文件 @ 16a5fd92
......@@ -34,8 +34,7 @@ enum {
RAMROD_RESTORE,
/* Execute the next command now */
RAMROD_EXEC,
/*
* Don't add a new command and continue execution of posponed
/* Don't add a new command and continue execution of postponed
* commands. If not set a new command will be added to the
* pending commands list.
*/
......@@ -129,8 +128,7 @@ enum bnx2x_vlan_mac_cmd {
struct bnx2x_vlan_mac_data {
/* Requested command: BNX2X_VLAN_MAC_XX */
enum bnx2x_vlan_mac_cmd cmd;
/*
* used to contain the data related vlan_mac_flags bits from
/* used to contain the data related vlan_mac_flags bits from
* ramrod parameters.
*/
unsigned long vlan_mac_flags;
......@@ -190,14 +188,10 @@ typedef struct bnx2x_exeq_elem *
struct bnx2x_exeq_elem *elem);
struct bnx2x_exe_queue_obj {
/*
* Commands pending for an execution.
*/
/* Commands pending for an execution. */
struct list_head exe_queue;
/*
* Commands pending for an completion.
*/
/* Commands pending for an completion. */
struct list_head pending_comp;
spinlock_t lock;
......@@ -245,14 +239,13 @@ struct bnx2x_exe_queue_obj {
};
/***************** Classification verbs: Set/Del MAC/VLAN/VLAN-MAC ************/
/*
* Element in the VLAN_MAC registry list having all currenty configured
* Element in the VLAN_MAC registry list having all currently configured
* rules.
*/
struct bnx2x_vlan_mac_registry_elem {
struct list_head link;
/*
* Used to store the cam offset used for the mac/vlan/vlan-mac.
/* Used to store the cam offset used for the mac/vlan/vlan-mac.
* Relevant for 57710 and 57711 only. VLANs and MACs share the
* same CAM for these chips.
*/
......@@ -310,7 +303,7 @@ struct bnx2x_vlan_mac_obj {
* @param n number of elements to get
* @param buf buffer preallocated by caller into which elements
* will be copied. Note elements are 4-byte aligned
* so buffer size must be able to accomodate the
* so buffer size must be able to accommodate the
* aligned elements.
*
* @return number of copied bytes
......@@ -395,7 +388,7 @@ struct bnx2x_vlan_mac_obj {
* @param bp
* @param p Command parameters (RAMROD_COMP_WAIT bit in
* ramrod_flags is only taken into an account)
* @param ppos a pointer to the cooky that should be given back in the
* @param ppos a pointer to the cookie that should be given back in the
* next call to make function handle the next element. If
* *ppos is set to NULL it will restart the iterator.
* If returned *ppos == NULL this means that the last
......@@ -408,7 +401,7 @@ struct bnx2x_vlan_mac_obj {
struct bnx2x_vlan_mac_registry_elem **ppos);
/**
* Should be called on a completion arival.
* Should be called on a completion arrival.
*
* @param bp
* @param o
......@@ -447,7 +440,7 @@ void bnx2x_set_mac_in_nig(struct bnx2x *bp,
/** RX_MODE verbs:DROP_ALL/ACCEPT_ALL/ACCEPT_ALL_MULTI/ACCEPT_ALL_VLAN/NORMAL */
/* RX_MODE ramrod spesial flags: set in rx_mode_flags field in
/* RX_MODE ramrod special flags: set in rx_mode_flags field in
* a bnx2x_rx_mode_ramrod_params.
*/
enum {
......@@ -475,8 +468,7 @@ struct bnx2x_rx_mode_ramrod_params {
unsigned long ramrod_flags;
unsigned long rx_mode_flags;
/*
* rdata is either a pointer to eth_filter_rules_ramrod_data(e2) or to
/* rdata is either a pointer to eth_filter_rules_ramrod_data(e2) or to
* a tstorm_eth_mac_filter_config (e1x).
*/
void *rdata;
......@@ -646,10 +638,9 @@ struct bnx2x_credit_pool_obj {
/* Maximum allowed credit. put() will check against it. */
int pool_sz;
/*
* Allocate a pool table statically.
/* Allocate a pool table statically.
*
* Currently the mamimum allowed size is MAX_MAC_CREDIT_E2(272)
* Currently the maximum allowed size is MAX_MAC_CREDIT_E2(272)
*
* The set bit in the table will mean that the entry is available.
*/
......@@ -832,7 +823,7 @@ enum {
BNX2X_Q_FLG_TUN_INC_INNER_IP_ID
};
/* Queue type options: queue type may be a compination of below. */
/* Queue type options: queue type may be a combination of below. */
enum bnx2x_q_type {
/** TODO: Consider moving both these flags into the init()
* ramrod params.
......@@ -1002,10 +993,9 @@ struct bnx2x_queue_sp_obj {
u8 cl_id;
u8 func_id;
/*
* number of traffic classes supported by queue.
* The primary connection of the queue suppotrs the first traffic
* class. Any further traffic class is suppoted by a tx-only
/* number of traffic classes supported by queue.
* The primary connection of the queue supports the first traffic
* class. Any further traffic class is supported by a tx-only
* connection.
*
* Therefore max_cos is also a number of valid entries in the cids
......@@ -1021,7 +1011,7 @@ struct bnx2x_queue_sp_obj {
/* BNX2X_Q_CMD_XX bits. This object implements "one
* pending" paradigm but for debug and tracing purposes it's
* more convinient to have different bits for different
* more convenient to have different bits for different
* commands.
*/
unsigned long pending;
......@@ -1210,7 +1200,7 @@ struct bnx2x_func_sp_obj {
/* BNX2X_FUNC_CMD_XX bits. This object implements "one
* pending" paradigm but for debug and tracing purposes it's
* more convinient to have different bits for different
* more convenient to have different bits for different
* commands.
*/
unsigned long pending;
......@@ -1329,7 +1319,7 @@ void bnx2x_init_rx_mode_obj(struct bnx2x *bp,
*
* @p: Command parameters
*
* Return: 0 - if operation was successfull and there is no pending completions,
* Return: 0 - if operation was successful and there is no pending completions,
* positive number - if there are pending completions,
* negative - if there were errors
*/
......@@ -1361,7 +1351,7 @@ void bnx2x_init_mcast_obj(struct bnx2x *bp,
* the current command will be enqueued to the tail of the
* pending commands list.
*
* Return: 0 is operation was successfull and there are no pending completions,
* Return: 0 is operation was successful and there are no pending completions,
* negative if there were errors, positive if there are pending
* completions.
*/
......
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c
浏览文件 @ 16a5fd92
......@@ -1341,7 +1341,7 @@ int bnx2x_vfop_qdown_cmd(struct bnx2x *bp,
*/
/* internal vf enable - until vf is enabled internally all transactions
* are blocked. this routine should always be called last with pretend.
* are blocked. This routine should always be called last with pretend.
*/
static void bnx2x_vf_enable_internal(struct bnx2x *bp, u8 enable)
{
......@@ -1743,7 +1743,7 @@ void bnx2x_iov_init_dq(struct bnx2x *bp)
REG_WR(bp, DORQ_REG_VF_TYPE_MIN_MCID_0, 0);
REG_WR(bp, DORQ_REG_VF_TYPE_MAX_MCID_0, 0x1ffff);
/* set the number of VF alllowed doorbells to the full DQ range */
/* set the number of VF allowed doorbells to the full DQ range */
REG_WR(bp, DORQ_REG_VF_NORM_MAX_CID_COUNT, 0x20000);
/* set the VF doorbell threshold */
......@@ -2403,7 +2403,7 @@ int bnx2x_iov_eq_sp_event(struct bnx2x *bp, union event_ring_elem *elem)
/* extract vf and rxq index from vf_cid - relies on the following:
* 1. vfid on cid reflects the true abs_vfid
* 2. the max number of VFs (per path) is 64
* 2. The max number of VFs (per path) is 64
*/
qidx = cid & ((1 << BNX2X_VF_CID_WND)-1);
abs_vfid = (cid >> BNX2X_VF_CID_WND) & (BNX2X_MAX_NUM_OF_VFS-1);
......@@ -2461,7 +2461,7 @@ static struct bnx2x_virtf *bnx2x_vf_by_cid(struct bnx2x *bp, int vf_cid)
{
/* extract the vf from vf_cid - relies on the following:
* 1. vfid on cid reflects the true abs_vfid
* 2. the max number of VFs (per path) is 64
* 2. The max number of VFs (per path) is 64
*/
int abs_vfid = (vf_cid >> BNX2X_VF_CID_WND) & (BNX2X_MAX_NUM_OF_VFS-1);
return bnx2x_vf_by_abs_fid(bp, abs_vfid);
......@@ -2480,7 +2480,7 @@ void bnx2x_iov_set_queue_sp_obj(struct bnx2x *bp, int vf_cid,
if (vf) {
/* extract queue index from vf_cid - relies on the following:
* 1. vfid on cid reflects the true abs_vfid
* 2. the max number of VFs (per path) is 64
* 2. The max number of VFs (per path) is 64
*/
int q_index = vf_cid & ((1 << BNX2X_VF_CID_WND)-1);
*q_obj = &bnx2x_vfq(vf, q_index, sp_obj);
......@@ -2705,7 +2705,7 @@ int bnx2x_vf_acquire(struct bnx2x *bp, struct bnx2x_virtf *vf,
}
/* static allocation:
* the global maximum number are fixed per VF. fail the request if
* the global maximum number are fixed per VF. Fail the request if
* requested number exceed these globals
*/
if (!bnx2x_vf_chk_avail_resc(bp, vf, resc)) {
......@@ -2890,7 +2890,7 @@ int bnx2x_vfop_close_cmd(struct bnx2x *bp,
return -ENOMEM;
}
/* VF release can be called either: 1. the VF was acquired but
/* VF release can be called either: 1. The VF was acquired but
* not enabled 2. the vf was enabled or in the process of being
* enabled
*/
......@@ -3140,7 +3140,7 @@ int bnx2x_get_vf_config(struct net_device *dev, int vfidx,
/* mac configured by ndo so its in bulletin board */
memcpy(&ivi->mac, bulletin->mac, ETH_ALEN);
else
/* funtion has not been loaded yet. Show mac as 0s */
/* function has not been loaded yet. Show mac as 0s */
memset(&ivi->mac, 0, ETH_ALEN);
/* vlan */
......@@ -3148,7 +3148,7 @@ int bnx2x_get_vf_config(struct net_device *dev, int vfidx,
/* vlan configured by ndo so its in bulletin board */
memcpy(&ivi->vlan, &bulletin->vlan, VLAN_HLEN);
else
/* funtion has not been loaded yet. Show vlans as 0s */
/* function has not been loaded yet. Show vlans as 0s */
memset(&ivi->vlan, 0, VLAN_HLEN);
}
......@@ -3188,7 +3188,7 @@ int bnx2x_set_vf_mac(struct net_device *dev, int vfidx, u8 *mac)
return -EINVAL;
}
/* update PF's copy of the VF's bulletin. will no longer accept mac
/* update PF's copy of the VF's bulletin. Will no longer accept mac
* configuration requests from vf unless match this mac
*/
bulletin->valid_bitmap |= 1 << MAC_ADDR_VALID;
......@@ -3357,8 +3357,11 @@ int bnx2x_set_vf_vlan(struct net_device *dev, int vfidx, u16 vlan, u8 qos)
return 0;
}
/* crc is the first field in the bulletin board. compute the crc over the
* entire bulletin board excluding the crc field itself
/* crc is the first field in the bulletin board. Compute the crc over the
* entire bulletin board excluding the crc field itself. Use the length field
* as the Bulletin Board was posted by a PF with possibly a different version
* from the vf which will sample it. Therefore, the length is computed by the
* PF and the used blindly by the VF.
*/
u32 bnx2x_crc_vf_bulletin(struct bnx2x *bp,
struct pf_vf_bulletin_content *bulletin)
......@@ -3451,7 +3454,7 @@ int bnx2x_open_epilog(struct bnx2x *bp)
* register_netdevice which must have rtnl lock taken. As we are holding
* the lock right now, that could only work if the probe would not take
* the lock. However, as the probe of the vf may be called from other
* contexts as well (such as passthrough to vm failes) it can't assume
* contexts as well (such as passthrough to vm fails) it can't assume
* the lock is being held for it. Using delayed work here allows the
* probe code to simply take the lock (i.e. wait for it to be released
* if it is being held). We only want to do this if the number of VFs
......
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h
浏览文件 @ 16a5fd92
......@@ -197,7 +197,7 @@ struct bnx2x_virtf {
u8 state;
#define VF_FREE 0 /* VF ready to be acquired holds no resc */
#define VF_ACQUIRED 1 /* VF aquired, but not initalized */
#define VF_ACQUIRED 1 /* VF acquired, but not initialized */
#define VF_ENABLED 2 /* VF Enabled */
#define VF_RESET 3 /* VF FLR'd, pending cleanup */
......
drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c
浏览文件 @ 16a5fd92
......@@ -233,7 +233,7 @@ int bnx2x_vfpf_acquire(struct bnx2x *bp, u8 tx_count, u8 rx_count)
attempts++;
/* test whether the PF accepted our request. If not, humble the
/* test whether the PF accepted our request. If not, humble
* the request and try again.
*/
if (bp->acquire_resp.hdr.status == PFVF_STATUS_SUCCESS) {
......@@ -787,7 +787,7 @@ static inline void bnx2x_set_vf_mbxs_valid(struct bnx2x *bp)
storm_memset_vf_mbx_valid(bp, bnx2x_vf(bp, i, abs_vfid));
}
/* enable vf_pf mailbox (aka vf-pf-chanell) */
/* enable vf_pf mailbox (aka vf-pf-channel) */
void bnx2x_vf_enable_mbx(struct bnx2x *bp, u8 abs_vfid)
{
bnx2x_vf_flr_clnup_epilog(bp, abs_vfid);
......@@ -1072,7 +1072,7 @@ static void bnx2x_vf_mbx_set_q_flags(struct bnx2x *bp, u32 mbx_q_flags,
if (mbx_q_flags & VFPF_QUEUE_FLG_DHC)
__set_bit(BNX2X_Q_FLG_DHC, sp_q_flags);
/* outer vlan removal is set according to the PF's multi fuction mode */
/* outer vlan removal is set according to PF's multi function mode */
if (IS_MF_SD(bp))
__set_bit(BNX2X_Q_FLG_OV, sp_q_flags);
}
......@@ -1104,7 +1104,7 @@ static void bnx2x_vf_mbx_setup_q(struct bnx2x *bp, struct bnx2x_virtf *vf,
struct bnx2x_queue_init_params *init_p;
struct bnx2x_queue_setup_params *setup_p;
/* reinit the VF operation context */
/* re-init the VF operation context */
memset(&vf->op_params.qctor, 0 , sizeof(vf->op_params.qctor));
setup_p = &vf->op_params.qctor.prep_qsetup;
init_p = &vf->op_params.qctor.qstate.params.init;
......
Markdown is supported
0% 或 .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑！
想要评论请 注册 或