3c505.h 6.4 KB
Newer Older
L
Linus Torvalds 已提交
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74
/*****************************************************************
 *
 *  defines for 3Com Etherlink Plus adapter
 *
 *****************************************************************/

#define ELP_DMA       6
#define ELP_RX_PCBS   4
#define ELP_MAX_CARDS 4

/*
 * I/O register offsets
 */
#define	PORT_COMMAND	0x00	/* read/write, 8-bit */
#define	PORT_STATUS	0x02	/* read only, 8-bit */
#define	PORT_AUXDMA	0x02	/* write only, 8-bit */
#define	PORT_DATA	0x04	/* read/write, 16-bit */
#define	PORT_CONTROL	0x06	/* read/write, 8-bit */

#define ELP_IO_EXTENT	0x10	/* size of used IO registers */

/*
 * host control registers bits
 */
#define	ATTN	0x80	/* attention */
#define	FLSH	0x40	/* flush data register */
#define DMAE	0x20	/* DMA enable */
#define DIR	0x10	/* direction */
#define	TCEN	0x08	/* terminal count interrupt enable */
#define	CMDE	0x04	/* command register interrupt enable */
#define	HSF2	0x02	/* host status flag 2 */
#define	HSF1	0x01	/* host status flag 1 */

/*
 * combinations of HSF flags used for PCB transmission
 */
#define	HSF_PCB_ACK	HSF1
#define	HSF_PCB_NAK	HSF2
#define	HSF_PCB_END	(HSF2|HSF1)
#define	HSF_PCB_MASK	(HSF2|HSF1)

/*
 * host status register bits
 */
#define	HRDY	0x80	/* data register ready */
#define	HCRE	0x40	/* command register empty */
#define	ACRF	0x20	/* adapter command register full */
/* #define DIR 	0x10	direction - same as in control register */
#define	DONE	0x08	/* DMA done */
#define	ASF3	0x04	/* adapter status flag 3 */
#define	ASF2	0x02	/* adapter status flag 2 */
#define	ASF1	0x01	/* adapter status flag 1 */

/*
 * combinations of ASF flags used for PCB reception
 */
#define	ASF_PCB_ACK	ASF1
#define	ASF_PCB_NAK	ASF2
#define	ASF_PCB_END	(ASF2|ASF1)
#define	ASF_PCB_MASK	(ASF2|ASF1)

/*
 * host aux DMA register bits
 */
#define	DMA_BRST	0x01	/* DMA burst */

/*
 * maximum amount of data allowed in a PCB
 */
#define	MAX_PCB_DATA	62

/*****************************************************************
 *
 *  timeout value
75
 *	this is a rough value used for loops to stop them from
L
Linus Torvalds 已提交
76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292
 *	locking up the whole machine in the case of failure or
 *	error conditions
 *
 *****************************************************************/

#define	TIMEOUT	300

/*****************************************************************
 *
 * PCB commands
 *
 *****************************************************************/

enum {
  /*
   * host PCB commands
   */
  CMD_CONFIGURE_ADAPTER_MEMORY	= 0x01,
  CMD_CONFIGURE_82586		= 0x02,
  CMD_STATION_ADDRESS		= 0x03,
  CMD_DMA_DOWNLOAD		= 0x04,
  CMD_DMA_UPLOAD		= 0x05,
  CMD_PIO_DOWNLOAD		= 0x06,
  CMD_PIO_UPLOAD		= 0x07,
  CMD_RECEIVE_PACKET		= 0x08,
  CMD_TRANSMIT_PACKET		= 0x09,
  CMD_NETWORK_STATISTICS	= 0x0a,
  CMD_LOAD_MULTICAST_LIST	= 0x0b,
  CMD_CLEAR_PROGRAM		= 0x0c,
  CMD_DOWNLOAD_PROGRAM		= 0x0d,
  CMD_EXECUTE_PROGRAM		= 0x0e,
  CMD_SELF_TEST			= 0x0f,
  CMD_SET_STATION_ADDRESS	= 0x10,
  CMD_ADAPTER_INFO		= 0x11,
  NUM_TRANSMIT_CMDS,

  /*
   * adapter PCB commands
   */
  CMD_CONFIGURE_ADAPTER_RESPONSE	= 0x31,
  CMD_CONFIGURE_82586_RESPONSE		= 0x32,
  CMD_ADDRESS_RESPONSE			= 0x33,
  CMD_DOWNLOAD_DATA_REQUEST		= 0x34,
  CMD_UPLOAD_DATA_REQUEST		= 0x35,
  CMD_RECEIVE_PACKET_COMPLETE		= 0x38,
  CMD_TRANSMIT_PACKET_COMPLETE		= 0x39,
  CMD_NETWORK_STATISTICS_RESPONSE	= 0x3a,
  CMD_LOAD_MULTICAST_RESPONSE		= 0x3b,
  CMD_CLEAR_PROGRAM_RESPONSE		= 0x3c,
  CMD_DOWNLOAD_PROGRAM_RESPONSE		= 0x3d,
  CMD_EXECUTE_RESPONSE			= 0x3e,
  CMD_SELF_TEST_RESPONSE		= 0x3f,
  CMD_SET_ADDRESS_RESPONSE		= 0x40,
  CMD_ADAPTER_INFO_RESPONSE		= 0x41
};

/* Definitions for the PCB data structure */

/* Data units */
typedef unsigned char         byte;
typedef unsigned short int    word;
typedef unsigned long int     dword;

/* Data structures */
struct Memconf {
	word	cmd_q,
		rcv_q,
		mcast,
		frame,
		rcv_b,
		progs;
};

struct Rcv_pkt {
	word	buf_ofs,
		buf_seg,
		buf_len,
		timeout;
};

struct Xmit_pkt {
	word	buf_ofs,
		buf_seg,
		pkt_len;
};

struct Rcv_resp {
	word	buf_ofs,
		buf_seg,
		buf_len,
		pkt_len,
		timeout,
		status;
	dword	timetag;
};

struct Xmit_resp {
	word	buf_ofs,
		buf_seg,
		c_stat,
		status;
};


struct Netstat {
	dword	tot_recv,
		tot_xmit;
	word	err_CRC,
		err_align,
		err_res,
		err_ovrrun;
};


struct Selftest {
	word	error;
	union {
		word ROM_cksum;
		struct {
			word ofs, seg;
		} RAM;
		word i82586;
	} failure;
};

struct Info {
	byte	minor_vers,
		major_vers;
	word	ROM_cksum,
		RAM_sz,
		free_ofs,
		free_seg;
};

struct Memdump {
       word size,
            off,
            seg;
};

/*
Primary Command Block. The most important data structure. All communication
between the host and the adapter is done with these. (Except for the actual
Ethernet data, which has different packaging.)
*/
typedef struct {
	byte	command;
	byte	length;
	union	{
		struct Memconf		memconf;
		word			configure;
		struct Rcv_pkt		rcv_pkt;
		struct Xmit_pkt		xmit_pkt;
		byte			multicast[10][6];
		byte			eth_addr[6];
		byte			failed;
		struct Rcv_resp		rcv_resp;
		struct Xmit_resp	xmit_resp;
		struct Netstat		netstat;
		struct Selftest		selftest;
		struct Info		info;
		struct Memdump    	memdump;
		byte			raw[62];
	} data;
} pcb_struct;

/* These defines for 'configure' */
#define RECV_STATION	0x00
#define RECV_BROAD	0x01
#define RECV_MULTI	0x02
#define RECV_PROMISC	0x04
#define NO_LOOPBACK	0x00
#define INT_LOOPBACK	0x08
#define EXT_LOOPBACK	0x10

/*****************************************************************
 *
 *  structure to hold context information for adapter
 *
 *****************************************************************/

#define DMA_BUFFER_SIZE  1600
#define BACKLOG_SIZE      4

typedef struct {
	volatile short got[NUM_TRANSMIT_CMDS];	/* flags for
						   command completion */
	pcb_struct tx_pcb;	/* PCB for foreground sending */
	pcb_struct rx_pcb;	/* PCB for foreground receiving */
	pcb_struct itx_pcb;	/* PCB for background sending */
	pcb_struct irx_pcb;	/* PCB for background receiving */

	void *dma_buffer;

	struct {
		unsigned int length[BACKLOG_SIZE];
		unsigned int in;
		unsigned int out;
	} rx_backlog;

	struct {
		unsigned int direction;
		unsigned int length;
		struct sk_buff *skb;
	        void *target;
		unsigned long start_time;
	} current_dma;

	/* flags */
	unsigned long send_pcb_semaphore;
	unsigned long dmaing;
	unsigned long busy;

	unsigned int rx_active;  /* number of receive PCBs */
        volatile unsigned char hcr_val;  /* what we think the HCR contains */
        spinlock_t lock;	/* Interrupt v tx lock */
} elp_device;
反馈
建议
客服 返回
顶部