/*
 * Copyright (C) 2012 Florian Vaussard, EPFL Mobots group
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

/*
 * The Gumstix Overo must be combined with an expansion board.
 */

/ {
	pwmleds {
		compatible = "pwm-leds";

		overo {
			label = "overo:blue:COM";
			pwms = <&twl_pwmled 1 7812500>;
			max-brightness = <127>;
			linux,default-trigger = "mmc0";
		};
	};

	sound {
		compatible = "ti,omap-twl4030";
		ti,model = "overo";

		ti,mcbsp = <&mcbsp2>;
		ti,codec = <&twl_audio>;
	};
};

&omap3_pmx_core {
	uart3_pins: pinmux_uart3_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0)	/* uart3_rx_irrx.uart3_rx_irrx */
			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)		/* uart3_tx_irtx.uart3_tx_irtx */
		>;
	};

	i2c1_pins: pinmux_i2c1_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0)		/* i2c1_scl.i2c1_scl */
			OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0)		/* i2c1_sda.i2c1_sda */
		>;
	};

	mmc1_pins: pinmux_mmc1_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_clk.sdmmc1_clk */
			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_cmd.sdmmc1_cmd */
			OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_dat0.sdmmc1_dat0 */
			OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_dat1.sdmmc1_dat1 */
			OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_dat2.sdmmc1_dat2 */
			OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_dat3.sdmmc1_dat3 */
		>;
	};
};

&i2c1 {
	pinctrl-names = "default";
	pinctrl-0 = <&i2c1_pins>;
	clock-frequency = <2600000>;

	twl: twl@48 {
		reg = <0x48>;
		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
		interrupt-parent = <&intc>;

		twl_audio: audio {
			compatible = "ti,twl4030-audio";
			codec {
			};
		};
	};
};

#include "twl4030.dtsi"
#include "twl4030_omap3.dtsi"

/* i2c2 pins are used for gpio */
&i2c2 {
	status = "disabled";
};

/* on board microSD slot */
&mmc1 {
	pinctrl-names = "default";
	pinctrl-0 = <&mmc1_pins>;
	vmmc-supply = <&vmmc1>;
	bus-width = <4>;
};

/* optional on board WiFi */
&mmc2 {
	bus-width = <4>;
};

&twl_gpio {
	ti,use-leds;
};

&usb_otg_hs {
	interface-type = <0>;
	usb-phy = <&usb2_phy>;
	phys = <&usb2_phy>;
	phy-names = "usb2-phy";
	mode = <3>;
	power = <50>;
};

&uart3 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart3_pins>;
};