# # USB Host Controller Drivers # comment "USB Host Controller Drivers" config USB_C67X00_HCD tristate "Cypress C67x00 HCD support" help The Cypress C67x00 (EZ-Host/EZ-OTG) chips are dual-role host/peripheral/OTG USB controllers. Enable this option to support this chip in host controller mode. If unsure, say N. To compile this driver as a module, choose M here: the module will be called c67x00. config USB_XHCI_HCD tristate "xHCI HCD (USB 3.0) support" ---help--- The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0 "SuperSpeed" host controller hardware. To compile this driver as a module, choose M here: the module will be called xhci-hcd. if USB_XHCI_HCD config USB_XHCI_PLATFORM tristate endif # USB_XHCI_HCD config USB_EHCI_HCD tristate "EHCI HCD (USB 2.0) support" ---help--- The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0 "high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware. If your USB host controller supports USB 2.0, you will likely want to configure this Host Controller Driver. EHCI controllers are packaged with "companion" host controllers (OHCI or UHCI) to handle USB 1.1 devices connected to root hub ports. Ports will connect to EHCI if the device is high speed, otherwise they connect to a companion controller. If you configure EHCI, you should probably configure the OHCI (for NEC and some other vendors) USB Host Controller Driver or UHCI (for Via motherboards) Host Controller Driver too. You may want to read . To compile this driver as a module, choose M here: the module will be called ehci-hcd. config USB_EHCI_ROOT_HUB_TT bool "Root Hub Transaction Translators" depends on USB_EHCI_HCD || USB_CHIPIDEA_HOST ---help--- Some EHCI chips have vendor-specific extensions to integrate transaction translators, so that no OHCI or UHCI companion controller is needed. It's safe to say "y" even if your controller doesn't support this feature. This supports the EHCI implementation that's originally from ARC, and has since changed hands a few times. config USB_EHCI_TT_NEWSCHED bool "Improved Transaction Translator scheduling" depends on USB_EHCI_HCD || USB_CHIPIDEA_HOST default y ---help--- This changes the periodic scheduling code to fill more of the low and full speed bandwidth available from the Transaction Translator (TT) in USB 2.0 hubs. Without this, only one transfer will be issued in each microframe, significantly reducing the number of periodic low/fullspeed transfers possible. If you have multiple periodic low/fullspeed devices connected to a highspeed USB hub which is connected to a highspeed USB Host Controller, and some of those devices will not work correctly (possibly due to "ENOSPC" or "-28" errors), say Y. Conversely, if you have only one such device and it doesn't work, you could try saying N. If unsure, say Y. config USB_FSL_MPH_DR_OF tristate if USB_EHCI_HCD config USB_EHCI_PCI tristate depends on PCI default y config USB_EHCI_HCD_PMC_MSP tristate "EHCI support for on-chip PMC MSP71xx USB controller" depends on MSP_HAS_USB default n select USB_EHCI_BIG_ENDIAN_DESC select USB_EHCI_BIG_ENDIAN_MMIO ---help--- Enables support for the onchip USB controller on the PMC_MSP7100 Family SoC's. If unsure, say N. config USB_EHCI_BIG_ENDIAN_MMIO bool config USB_EHCI_BIG_ENDIAN_DESC bool config XPS_USB_HCD_XILINX bool "Use Xilinx usb host EHCI controller core" depends on (PPC32 || MICROBLAZE) select USB_EHCI_BIG_ENDIAN_DESC select USB_EHCI_BIG_ENDIAN_MMIO ---help--- Xilinx xps USB host controller core is EHCI compilant and has transaction translator built-in. It can be configured to either support both high speed and full speed devices, or high speed devices only. config USB_EHCI_FSL bool "Support for Freescale PPC on-chip EHCI USB controller" depends on FSL_SOC select USB_EHCI_ROOT_HUB_TT select USB_FSL_MPH_DR_OF if OF ---help--- Variation of ARC USB block used in some Freescale chips. config USB_EHCI_MXC tristate "Support for Freescale i.MX on-chip EHCI USB controller" depends on ARCH_MXC select USB_EHCI_ROOT_HUB_TT ---help--- Variation of ARC USB block used in some Freescale chips. config USB_EHCI_HCD_OMAP tristate "EHCI support for OMAP3 and later chips" depends on ARCH_OMAP default y ---help--- Enables support for the on-chip EHCI controller on OMAP3 and later chips. If your system uses a PHY on the USB port, you will need to enable USB_PHY and the appropriate PHY driver as well. Most boards need the NOP_USB_XCEIV PHY driver. config USB_EHCI_HCD_ORION tristate "Support for Marvell EBU on-chip EHCI USB controller" depends on USB_EHCI_HCD && PLAT_ORION default y ---help--- Enables support for the on-chip EHCI controller on Marvell's embedded ARM SoCs, including Orion, Kirkwood, Dove, Armada XP, Armada 370. This is different from the EHCI implementation on Marvell's mobile PXA and MMP SoC, see "EHCI support for Marvell PXA/MMP USB controller" for those. config USB_EHCI_HCD_SPEAR tristate "Support for ST SPEAr on-chip EHCI USB controller" depends on USB_EHCI_HCD && PLAT_SPEAR default y ---help--- Enables support for the on-chip EHCI controller on ST SPEAr chips. config USB_EHCI_HCD_AT91 tristate "Support for Atmel on-chip EHCI USB controller" depends on USB_EHCI_HCD && ARCH_AT91 default y ---help--- Enables support for the on-chip EHCI controller on Atmel chips. config USB_EHCI_MSM tristate "Support for Qualcomm QSD/MSM on-chip EHCI USB controller" depends on ARCH_MSM depends on USB_PHY select USB_EHCI_ROOT_HUB_TT select USB_MSM_OTG ---help--- Enables support for the USB Host controller present on the Qualcomm chipsets. Root Hub has inbuilt TT. This driver depends on OTG driver for PHY initialization, clock management, powering up VBUS, and power management. This driver is not supported on boards like trout which has an external PHY. config USB_EHCI_TEGRA tristate "NVIDIA Tegra HCD support" depends on ARCH_TEGRA select USB_EHCI_ROOT_HUB_TT select USB_PHY help This driver enables support for the internal USB Host Controllers found in NVIDIA Tegra SoCs. The controllers are EHCI compliant. config USB_EHCI_HCD_PPC_OF bool "EHCI support for PPC USB controller on OF platform bus" depends on PPC_OF default y ---help--- Enables support for the USB controller present on the PowerPC OpenFirmware platform bus. config USB_EHCI_SH bool "EHCI support for SuperH USB controller" depends on SUPERH ---help--- Enables support for the on-chip EHCI controller on the SuperH. If you use the PCI EHCI controller, this option is not necessary. config USB_EHCI_S5P tristate "EHCI support for Samsung S5P/EXYNOS SoC Series" depends on PLAT_S5P || ARCH_EXYNOS help Enable support for the Samsung S5Pxxxx and Exynos3/4/5 SOC's on-chip EHCI controller. config USB_EHCI_MV bool "EHCI support for Marvell PXA/MMP USB controller" depends on (ARCH_PXA || ARCH_MMP) select USB_EHCI_ROOT_HUB_TT ---help--- Enables support for Marvell (including PXA and MMP series) on-chip USB SPH and OTG controller. SPH is a single port host, and it can only be EHCI host. OTG is controller that can switch to host mode. Note that this driver will not work on Marvell's other EHCI controller used by the EBU-type SoCs including Orion, Kirkwood, Dova, Armada 370 and Armada XP. See "Support for Marvell EBU on-chip EHCI USB controller" for those. config USB_W90X900_EHCI bool "W90X900(W90P910) EHCI support" depends on ARCH_W90X900 ---help--- Enables support for the W90X900 USB controller config USB_CNS3XXX_EHCI bool "Cavium CNS3XXX EHCI Module (DEPRECATED)" depends on ARCH_CNS3XXX select USB_EHCI_HCD_PLATFORM ---help--- This option is deprecated now and the driver was removed, use USB_EHCI_HCD_PLATFORM instead. Enable support for the CNS3XXX SOC's on-chip EHCI controller. It is needed for high-speed (480Mbit/sec) USB 2.0 device support. config USB_EHCI_ATH79 bool "EHCI support for AR7XXX/AR9XXX SoCs (DEPRECATED)" depends on (SOC_AR71XX || SOC_AR724X || SOC_AR913X || SOC_AR933X) select USB_EHCI_ROOT_HUB_TT select USB_EHCI_HCD_PLATFORM default y ---help--- This option is deprecated now and the driver was removed, use USB_EHCI_HCD_PLATFORM instead. Enables support for the built-in EHCI controller present on the Atheros AR7XXX/AR9XXX SoCs. config USB_EHCI_HCD_PLATFORM tristate "Generic EHCI driver for a platform device" default n ---help--- Adds an EHCI host driver for a generic platform device, which provides a memory space and an irq. If unsure, say N. config USB_OCTEON_EHCI bool "Octeon on-chip EHCI support" depends on CAVIUM_OCTEON_SOC default n select USB_EHCI_BIG_ENDIAN_MMIO help Enable support for the Octeon II SOC's on-chip EHCI controller. It is needed for high-speed (480Mbit/sec) USB 2.0 device support. All CN6XXX based chips with USB are supported. endif # USB_EHCI_HCD config USB_OXU210HP_HCD tristate "OXU210HP HCD support" depends on GENERIC_HARDIRQS ---help--- The OXU210HP is an USB host/OTG/device controller. Enable this option if your board has this chip. If unsure, say N. This driver does not support isochronous transfers and doesn't implement OTG nor USB device controllers. To compile this driver as a module, choose M here: the module will be called oxu210hp-hcd. config USB_ISP116X_HCD tristate "ISP116X HCD support" ---help--- The ISP1160 and ISP1161 chips are USB host controllers. Enable this option if your board has this chip. If unsure, say N. This driver does not support isochronous transfers. To compile this driver as a module, choose M here: the module will be called isp116x-hcd. config USB_ISP1760_HCD tristate "ISP 1760 HCD support" ---help--- The ISP1760 chip is a USB 2.0 host controller. This driver does not support isochronous transfers or OTG. This USB controller is usually attached to a non-DMA-Master capable bus. NXP's eval kit brings this chip on PCI card where the chip itself is behind a PLB to simulate such a bus. To compile this driver as a module, choose M here: the module will be called isp1760. config USB_ISP1362_HCD tristate "ISP1362 HCD support" default N ---help--- Supports the Philips ISP1362 chip as a host controller This driver does not support isochronous transfers. To compile this driver as a module, choose M here: the module will be called isp1362-hcd. config USB_FUSBH200_HCD tristate "FUSBH200 HCD support" depends on USB default N ---help--- Faraday FUSBH200 is designed to meet USB2.0 EHCI specification with minor modification. To compile this driver as a module, choose M here: the module will be called fusbh200-hcd. config USB_FOTG210_HCD tristate "FOTG210 HCD support" depends on USB default N ---help--- Faraday FOTG210 is an OTG controller which can be configured as an USB2.0 host. It is designed to meet USB2.0 EHCI specification with minor modification. To compile this driver as a module, choose M here: the module will be called fotg210-hcd. config USB_OHCI_HCD tristate "OHCI HCD (USB 1.1) support" select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3 depends on USB_ISP1301 || !ARCH_LPC32XX ---help--- The Open Host Controller Interface (OHCI) is a standard for accessing USB 1.1 host controller hardware. It does more in hardware than Intel's UHCI specification. If your USB host controller follows the OHCI spec, say Y. On most non-x86 systems, and on x86 hardware that's not using a USB controller from Intel or VIA, this is appropriate. If your host controller doesn't use PCI, this is probably appropriate. For a PCI based system where you're not sure, the "lspci -v" entry will list the right "prog-if" for your USB controller(s): EHCI, OHCI, or UHCI. To compile this driver as a module, choose M here: the module will be called ohci-hcd. if USB_OHCI_HCD config USB_OHCI_HCD_OMAP1 bool "OHCI support for OMAP1/2 chips" depends on ARCH_OMAP1 default y ---help--- Enables support for the OHCI controller on OMAP1/2 chips. config USB_OHCI_HCD_OMAP3 bool "OHCI support for OMAP3 and later chips" depends on (ARCH_OMAP3 || ARCH_OMAP4) default y ---help--- Enables support for the on-chip OHCI controller on OMAP3 and later chips. config USB_OHCI_ATH79 bool "USB OHCI support for the Atheros AR71XX/AR7240 SoCs (DEPRECATED)" depends on (SOC_AR71XX || SOC_AR724X) select USB_OHCI_HCD_PLATFORM default y help This option is deprecated now and the driver was removed, use USB_OHCI_HCD_PLATFORM instead. Enables support for the built-in OHCI controller present on the Atheros AR71XX/AR7240 SoCs. config USB_OHCI_HCD_PPC_OF_BE bool "OHCI support for OF platform bus (big endian)" depends on PPC_OF select USB_OHCI_BIG_ENDIAN_DESC select USB_OHCI_BIG_ENDIAN_MMIO ---help--- Enables support for big-endian USB controllers present on the OpenFirmware platform bus. config USB_OHCI_HCD_PPC_OF_LE bool "OHCI support for OF platform bus (little endian)" depends on PPC_OF select USB_OHCI_LITTLE_ENDIAN ---help--- Enables support for little-endian USB controllers present on the OpenFirmware platform bus. config USB_OHCI_HCD_PPC_OF bool depends on PPC_OF default USB_OHCI_HCD_PPC_OF_BE || USB_OHCI_HCD_PPC_OF_LE config USB_OHCI_HCD_PCI tristate "OHCI support for PCI-bus USB controllers" depends on PCI default y select USB_OHCI_LITTLE_ENDIAN ---help--- Enables support for PCI-bus plug-in USB controller cards. If unsure, say Y. config USB_OHCI_HCD_SSB bool "OHCI support for Broadcom SSB OHCI core (DEPRECATED)" depends on (SSB = y || SSB = USB_OHCI_HCD) select USB_HCD_SSB select USB_OHCI_HCD_PLATFORM default n ---help--- This option is deprecated now and the driver was removed, use USB_HCD_SSB and USB_OHCI_HCD_PLATFORM instead. Support for the Sonics Silicon Backplane (SSB) attached Broadcom USB OHCI core. This device is present in some embedded devices with Broadcom based SSB bus. If unsure, say N. config USB_OHCI_SH bool "OHCI support for SuperH USB controller (DEPRECATED)" depends on SUPERH select USB_OHCI_HCD_PLATFORM ---help--- This option is deprecated now and the driver was removed, use USB_OHCI_HCD_PLATFORM instead. Enables support for the on-chip OHCI controller on the SuperH. If you use the PCI OHCI controller, this option is not necessary. config USB_OHCI_EXYNOS boolean "OHCI support for Samsung EXYNOS SoC Series" depends on ARCH_EXYNOS help Enable support for the Samsung Exynos SOC's on-chip OHCI controller. config USB_CNS3XXX_OHCI bool "Cavium CNS3XXX OHCI Module (DEPRECATED)" depends on ARCH_CNS3XXX select USB_OHCI_HCD_PLATFORM ---help--- This option is deprecated now and the driver was removed, use USB_OHCI_HCD_PLATFORM instead. Enable support for the CNS3XXX SOC's on-chip OHCI controller. It is needed for low-speed USB 1.0 device support. config USB_OHCI_HCD_PLATFORM tristate "Generic OHCI driver for a platform device" default n ---help--- Adds an OHCI host driver for a generic platform device, which provides a memory space and an irq. If unsure, say N. config USB_OCTEON_OHCI bool "Octeon on-chip OHCI support" depends on CAVIUM_OCTEON_SOC default USB_OCTEON_EHCI select USB_OHCI_BIG_ENDIAN_MMIO select USB_OHCI_LITTLE_ENDIAN help Enable support for the Octeon II SOC's on-chip OHCI controller. It is needed for low-speed USB 1.0 device support. All CN6XXX based chips with USB are supported. config USB_OHCI_BIG_ENDIAN_DESC bool default n config USB_OHCI_BIG_ENDIAN_MMIO bool default n config USB_OHCI_LITTLE_ENDIAN bool default n if STB03xxx || PPC_MPC52xx default y endif # USB_OHCI_HCD config USB_UHCI_HCD tristate "UHCI HCD (most Intel and VIA) support" depends on PCI || USB_UHCI_SUPPORT_NON_PCI_HC ---help--- The Universal Host Controller Interface is a standard by Intel for accessing the USB hardware in the PC (which is also called the USB host controller). If your USB host controller conforms to this standard, you may want to say Y, but see below. All recent boards with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX, i810, i820) conform to this standard. Also all VIA PCI chipsets (like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro 133) and LEON/GRLIB SoCs with the GRUSBHC controller. If unsure, say Y. To compile this driver as a module, choose M here: the module will be called uhci-hcd. config USB_UHCI_SUPPORT_NON_PCI_HC bool default y if (SPARC_LEON || USB_UHCI_PLATFORM) config USB_UHCI_PLATFORM bool default y if ARCH_VT8500 config USB_UHCI_BIG_ENDIAN_MMIO bool default y if SPARC_LEON config USB_UHCI_BIG_ENDIAN_DESC bool default y if SPARC_LEON config USB_FHCI_HCD tristate "Freescale QE USB Host Controller support" depends on OF_GPIO && QE_GPIO && QUICC_ENGINE select FSL_GTM select QE_USB help This driver enables support for Freescale QE USB Host Controller (as found on MPC8360 and MPC8323 processors), the driver supports Full and Low Speed USB. config FHCI_DEBUG bool "Freescale QE USB Host Controller debug support" depends on USB_FHCI_HCD && DEBUG_FS help Say "y" to see some FHCI debug information and statistics through debugfs. config USB_U132_HCD tristate "Elan U132 Adapter Host Controller" depends on USB_FTDI_ELAN default M help The U132 adapter is a USB to CardBus adapter specifically designed for PC cards that contain an OHCI host controller. Typical PC cards are the Orange Mobile 3G Option GlobeTrotter Fusion card. The U132 adapter will *NOT* work with PC cards that do not contain an OHCI controller. For those PC cards that contain multiple OHCI controllers only the first one is used. The driver consists of two modules, the "ftdi-elan" module is a USB client driver that interfaces to the FTDI chip within ELAN's USB-to-PCMCIA adapter, and this "u132-hcd" module is a USB host controller driver that talks to the OHCI controller within the CardBus cards that are inserted in the U132 adapter. This driver has been tested with a CardBus OHCI USB adapter, and worked with a USB PEN Drive inserted into the first USB port of the PCCARD. A rather pointless thing to do, but useful for testing. It is safe to say M here. See also config USB_SL811_HCD tristate "SL811HS HCD support" help The SL811HS is a single-port USB controller that supports either host side or peripheral side roles. Enable this option if your board has this chip, and you want to use it as a host controller. If unsure, say N. To compile this driver as a module, choose M here: the module will be called sl811-hcd. config USB_SL811_HCD_ISO bool "partial ISO support" depends on USB_SL811_HCD help The driver doesn't support iso_frame_desc (yet), but for some simple devices that just queue one ISO frame per URB, then ISO transfers "should" work using the normal urb status fields. If unsure, say N. config USB_SL811_CS tristate "CF/PCMCIA support for SL811HS HCD" depends on USB_SL811_HCD && PCMCIA help Wraps a PCMCIA driver around the SL811HS HCD, supporting the RATOC REX-CFU1U CF card (often used with PDAs). If unsure, say N. To compile this driver as a module, choose M here: the module will be called "sl811_cs". config USB_R8A66597_HCD tristate "R8A66597 HCD support" help The R8A66597 is a USB 2.0 host and peripheral controller. Enable this option if your board has this chip, and you want to use it as a host controller. If unsure, say N. To compile this driver as a module, choose M here: the module will be called r8a66597-hcd. config USB_RENESAS_USBHS_HCD tristate "Renesas USBHS HCD support" depends on USB_RENESAS_USBHS help The Renesas USBHS is a USB 2.0 host and peripheral controller. Enable this option if your board has this chip, and you want to use it as a host controller. If unsure, say N. To compile this driver as a module, choose M here: the module will be called renesas-usbhs. config USB_WHCI_HCD tristate "Wireless USB Host Controller Interface (WHCI) driver" depends on PCI && USB && UWB select USB_WUSB select UWB_WHCI help A driver for PCI-based Wireless USB Host Controllers that are compliant with the WHCI specification. To compile this driver a module, choose M here: the module will be called "whci-hcd". config USB_HWA_HCD tristate "Host Wire Adapter (HWA) driver" depends on UWB select USB_WUSB select UWB_HWA help This driver enables you to connect Wireless USB devices to your system using a Host Wire Adaptor USB dongle. This is an UWB Radio Controller and WUSB Host Controller connected to your machine via USB (specified in WUSB1.0). To compile this driver a module, choose M here: the module will be called "hwa-hc". config USB_IMX21_HCD tristate "i.MX21 HCD support" depends on ARM && ARCH_MXC help This driver enables support for the on-chip USB host in the i.MX21 processor. To compile this driver as a module, choose M here: the module will be called "imx21-hcd". config USB_OCTEON2_COMMON bool default y if USB_OCTEON_EHCI || USB_OCTEON_OHCI config USB_HCD_BCMA tristate "BCMA usb host driver" depends on BCMA select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD help Enable support for the EHCI and OCHI host controller on an bcma bus. It converts the bcma driver into two platform device drivers for ehci and ohci. If unsure, say N. config USB_HCD_SSB tristate "SSB usb host driver" depends on SSB select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD help Enable support for the EHCI and OCHI host controller on an bcma bus. It converts the bcma driver into two platform device drivers for ehci and ohci. If unsure, say N.