.. -*- coding: utf-8; mode: rst -*-

.. _lirc_ioctl:

************
LIRC ioctl()
************


Name
====

LIRC ioctl - Sends a I/O control command to a LIRC device

Synopsis
========

.. cpp:function:: int ioctl( int fd, int request, struct v4l2_capability *argp )


Arguments
=========

``fd``
    File descriptor returned by ``open()``.

``request``
    The type of I/O control that will be used. See table :ref:`lirc-request`
    for details.

``argp``
    Arguments for the I/O control. They're specific to each request.


The LIRC device's ioctl definition is bound by the ioctl function
definition of struct file_operations, leaving us with an unsigned int
for the ioctl command and an unsigned long for the arg. For the purposes
of ioctl portability across 32-bit and 64-bit, these values are capped
to their 32-bit sizes.

The ioctls can be used to change specific hardware settings.
In general each driver should have a default set of settings. The driver
implementation is expected to re-apply the default settings when the
device is closed by user-space, so that every application opening the
device can rely on working with the default settings initially.

.. _lirc-request:

I/O control requests
====================

.. _LIRC_GET_MIN_TIMEOUT:
.. _LIRC_GET_MAX_TIMEOUT:

``LIRC_GET_M{IN,AX}_TIMEOUT``

    Some devices have internal timers that can be used to detect when
    there's no IR activity for a long time. This can help lircd in
    detecting that a IR signal is finished and can speed up the decoding
    process. Returns an integer value with the minimum/maximum timeout
    that can be set. Some devices have a fixed timeout, in that case
    both ioctls will return the same value even though the timeout
    cannot be changed.

.. _LIRC_GET_LENGTH:

``LIRC_GET_LENGTH``

    Retrieves the code length in bits (only for ``LIRC_MODE_LIRCCODE).``
    Reads on the device must be done in blocks matching the bit count.
    The bit could should be rounded up so that it matches full bytes.

.. _LIRC_SET_SEND_MODE:
.. _LIRC_SET_REC_MODE:

``LIRC_SET_{SEND,REC}_MODE``

    Set send/receive mode. Largely obsolete for send, as only
    ``LIRC_MODE_PULSE`` is supported.

.. _LIRC_SET_SEND_CARRIER:
.. _LIRC_SET_REC_CARRIER:

``LIRC_SET_{SEND,REC}_CARRIER``

    Set send/receive carrier (in Hz).

.. _LIRC_SET_TRANSMITTER_MASK:

``LIRC_SET_TRANSMITTER_MASK``

    This enables the given set of transmitters. The first transmitter is
    encoded by the least significant bit, etc. When an invalid bit mask
    is given, i.e. a bit is set, even though the device does not have so
    many transitters, then this ioctl returns the number of available
    transitters and does nothing otherwise.

.. _LIRC_SET_REC_TIMEOUT:

``LIRC_SET_REC_TIMEOUT``

    Sets the integer value for IR inactivity timeout (cf.
    ``LIRC_GET_MIN_TIMEOUT`` and ``LIRC_GET_MAX_TIMEOUT).`` A value of 0
    (if supported by the hardware) disables all hardware timeouts and
    data should be reported as soon as possible. If the exact value
    cannot be set, then the next possible value _greater_ than the
    given value should be set.

.. _LIRC_SET_REC_TIMEOUT_REPORTS:

``LIRC_SET_REC_TIMEOUT_REPORTS``

    Enable (1) or disable (0) timeout reports in ``LIRC_MODE_MODE2.`` By
    default, timeout reports should be turned off.


.. _LIRC_SET_MEASURE_CARRIER_MODE:
.. _lirc-mode2-frequency:

``LIRC_SET_MEASURE_CARRIER_MODE``

    Enable (1)/disable (0) measure mode. If enabled, from the next key
    press on, the driver will send ``LIRC_MODE2_FREQUENCY`` packets. By
    default this should be turned off.


.. _LIRC_SET_REC_CARRIER_RANGE:

``LIRC_SET_REC_CARRIER_RANGE``

    To set a range use
    ``LIRC_SET_REC_CARRIER_RANGE``
    with the lower bound first and later
    ``LIRC_SET_REC_CARRIER`` with the upper
    bound.

.. _LIRC_SET_WIDEBAND_RECEIVER:

``LIRC_SET_WIDEBAND_RECEIVER``

    Some receivers are equipped with special wide band receiver which is
    intended to be used to learn output of existing remote. Calling that
    ioctl with (1) will enable it, and with (0) disable it. This might
    be useful of receivers that have otherwise narrow band receiver that
    prevents them to be used with some remotes. Wide band receiver might
    also be more precise On the other hand its disadvantage it usually
    reduced range of reception.

    .. note:: Wide band receiver might be
       implictly enabled if you enable carrier reports. In that case it
       will be disabled as soon as you disable carrier reports. Trying to
       disable wide band receiver while carrier reports are active will do
       nothing.


.. _lirc_dev_errors:

Return Value
============

On success 0 is returned, on error -1 and the ``errno`` variable is set
appropriately. The generic error codes are described at the
:ref:`Generic Error Codes <gen-errors>` chapter.