/* * Copyright 2002-2005, Instant802 Networks, Inc. * Copyright 2005-2006, Devicescape Software, Inc. * Copyright 2006-2007 Jiri Benc * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "ieee80211_i.h" #include "rate.h" #include "mesh.h" #include "wep.h" #include "wme.h" #include "aes_ccm.h" #include "led.h" #include "cfg.h" #include "debugfs.h" #include "debugfs_netdev.h" /* * For seeing transmitted packets on monitor interfaces * we have a radiotap header too. */ struct ieee80211_tx_status_rtap_hdr { struct ieee80211_radiotap_header hdr; __le16 tx_flags; u8 data_retries; } __attribute__ ((packed)); /* common interface routines */ static int header_parse_80211(const struct sk_buff *skb, unsigned char *haddr) { memcpy(haddr, skb_mac_header(skb) + 10, ETH_ALEN); /* addr2 */ return ETH_ALEN; } /* must be called under mdev tx lock */ static void ieee80211_configure_filter(struct ieee80211_local *local) { unsigned int changed_flags; unsigned int new_flags = 0; if (atomic_read(&local->iff_promiscs)) new_flags |= FIF_PROMISC_IN_BSS; if (atomic_read(&local->iff_allmultis)) new_flags |= FIF_ALLMULTI; if (local->monitors) new_flags |= FIF_BCN_PRBRESP_PROMISC; if (local->fif_fcsfail) new_flags |= FIF_FCSFAIL; if (local->fif_plcpfail) new_flags |= FIF_PLCPFAIL; if (local->fif_control) new_flags |= FIF_CONTROL; if (local->fif_other_bss) new_flags |= FIF_OTHER_BSS; changed_flags = local->filter_flags ^ new_flags; /* be a bit nasty */ new_flags |= (1<<31); local->ops->configure_filter(local_to_hw(local), changed_flags, &new_flags, local->mdev->mc_count, local->mdev->mc_list); WARN_ON(new_flags & (1<<31)); local->filter_flags = new_flags & ~(1<<31); } /* master interface */ static int ieee80211_master_open(struct net_device *dev) { struct ieee80211_local *local = wdev_priv(dev->ieee80211_ptr); struct ieee80211_sub_if_data *sdata; int res = -EOPNOTSUPP; /* we hold the RTNL here so can safely walk the list */ list_for_each_entry(sdata, &local->interfaces, list) { if (netif_running(sdata->dev)) { res = 0; break; } } if (res) return res; netif_tx_start_all_queues(local->mdev); return 0; } static int ieee80211_master_stop(struct net_device *dev) { struct ieee80211_local *local = wdev_priv(dev->ieee80211_ptr); struct ieee80211_sub_if_data *sdata; /* we hold the RTNL here so can safely walk the list */ list_for_each_entry(sdata, &local->interfaces, list) if (netif_running(sdata->dev)) dev_close(sdata->dev); return 0; } static void ieee80211_master_set_multicast_list(struct net_device *dev) { struct ieee80211_local *local = wdev_priv(dev->ieee80211_ptr); ieee80211_configure_filter(local); } /* regular interfaces */ static int ieee80211_change_mtu(struct net_device *dev, int new_mtu) { int meshhdrlen; struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev); meshhdrlen = (sdata->vif.type == IEEE80211_IF_TYPE_MESH_POINT) ? 5 : 0; /* FIX: what would be proper limits for MTU? * This interface uses 802.3 frames. */ if (new_mtu < 256 || new_mtu > IEEE80211_MAX_DATA_LEN - 24 - 6 - meshhdrlen) { return -EINVAL; } #ifdef CONFIG_MAC80211_VERBOSE_DEBUG printk(KERN_DEBUG "%s: setting MTU %d\n", dev->name, new_mtu); #endif /* CONFIG_MAC80211_VERBOSE_DEBUG */ dev->mtu = new_mtu; return 0; } static inline int identical_mac_addr_allowed(int type1, int type2) { return (type1 == IEEE80211_IF_TYPE_MNTR || type2 == IEEE80211_IF_TYPE_MNTR || (type1 == IEEE80211_IF_TYPE_AP && type2 == IEEE80211_IF_TYPE_WDS) || (type1 == IEEE80211_IF_TYPE_WDS && (type2 == IEEE80211_IF_TYPE_WDS || type2 == IEEE80211_IF_TYPE_AP)) || (type1 == IEEE80211_IF_TYPE_AP && type2 == IEEE80211_IF_TYPE_VLAN) || (type1 == IEEE80211_IF_TYPE_VLAN && (type2 == IEEE80211_IF_TYPE_AP || type2 == IEEE80211_IF_TYPE_VLAN))); } static int ieee80211_open(struct net_device *dev) { struct ieee80211_sub_if_data *sdata, *nsdata; struct ieee80211_local *local = wdev_priv(dev->ieee80211_ptr); struct sta_info *sta; struct ieee80211_if_init_conf conf; u32 changed = 0; int res; bool need_hw_reconfig = 0; u8 null_addr[ETH_ALEN] = {0}; sdata = IEEE80211_DEV_TO_SUB_IF(dev); /* fail early if user set an invalid address */ if (compare_ether_addr(dev->dev_addr, null_addr) && !is_valid_ether_addr(dev->dev_addr)) return -EADDRNOTAVAIL; /* we hold the RTNL here so can safely walk the list */ list_for_each_entry(nsdata, &local->interfaces, list) { struct net_device *ndev = nsdata->dev; if (ndev != dev && netif_running(ndev)) { /* * Allow only a single IBSS interface to be up at any * time. This is restricted because beacon distribution * cannot work properly if both are in the same IBSS. * * To remove this restriction we'd have to disallow them * from setting the same SSID on different IBSS interfaces * belonging to the same hardware. Then, however, we're * faced with having to adopt two different TSF timers... */ if (sdata->vif.type == IEEE80211_IF_TYPE_IBSS && nsdata->vif.type == IEEE80211_IF_TYPE_IBSS) return -EBUSY; /* * The remaining checks are only performed for interfaces * with the same MAC address. */ if (compare_ether_addr(dev->dev_addr, ndev->dev_addr)) continue; /* * check whether it may have the same address */ if (!identical_mac_addr_allowed(sdata->vif.type, nsdata->vif.type)) return -ENOTUNIQ; /* * can only add VLANs to enabled APs */ if (sdata->vif.type == IEEE80211_IF_TYPE_VLAN && nsdata->vif.type == IEEE80211_IF_TYPE_AP) sdata->bss = &nsdata->u.ap; } } switch (sdata->vif.type) { case IEEE80211_IF_TYPE_WDS: if (!is_valid_ether_addr(sdata->u.wds.remote_addr)) return -ENOLINK; break; case IEEE80211_IF_TYPE_VLAN: if (!sdata->bss) return -ENOLINK; list_add(&sdata->u.vlan.list, &sdata->bss->vlans); break; case IEEE80211_IF_TYPE_AP: sdata->bss = &sdata->u.ap; break; case IEEE80211_IF_TYPE_MESH_POINT: if (!ieee80211_vif_is_mesh(&sdata->vif)) break; /* mesh ifaces must set allmulti to forward mcast traffic */ atomic_inc(&local->iff_allmultis); break; case IEEE80211_IF_TYPE_STA: case IEEE80211_IF_TYPE_MNTR: case IEEE80211_IF_TYPE_IBSS: /* no special treatment */ break; case IEEE80211_IF_TYPE_INVALID: /* cannot happen */ WARN_ON(1); break; } if (local->open_count == 0) { res = 0; if (local->ops->start) res = local->ops->start(local_to_hw(local)); if (res) goto err_del_bss; need_hw_reconfig = 1; ieee80211_led_radio(local, local->hw.conf.radio_enabled); } /* * Check all interfaces and copy the hopefully now-present * MAC address to those that have the special null one. */ list_for_each_entry(nsdata, &local->interfaces, list) { struct net_device *ndev = nsdata->dev; /* * No need to check netif_running since we do not allow * it to start up with this invalid address. */ if (compare_ether_addr(null_addr, ndev->dev_addr) == 0) memcpy(ndev->dev_addr, local->hw.wiphy->perm_addr, ETH_ALEN); } if (compare_ether_addr(null_addr, local->mdev->dev_addr) == 0) memcpy(local->mdev->dev_addr, local->hw.wiphy->perm_addr, ETH_ALEN); /* * Validate the MAC address for this device. */ if (!is_valid_ether_addr(dev->dev_addr)) { if (!local->open_count && local->ops->stop) local->ops->stop(local_to_hw(local)); return -EADDRNOTAVAIL; } switch (sdata->vif.type) { case IEEE80211_IF_TYPE_VLAN: /* no need to tell driver */ break; case IEEE80211_IF_TYPE_MNTR: if (sdata->u.mntr_flags & MONITOR_FLAG_COOK_FRAMES) { local->cooked_mntrs++; break; } /* must be before the call to ieee80211_configure_filter */ local->monitors++; if (local->monitors == 1) local->hw.conf.flags |= IEEE80211_CONF_RADIOTAP; if (sdata->u.mntr_flags & MONITOR_FLAG_FCSFAIL) local->fif_fcsfail++; if (sdata->u.mntr_flags & MONITOR_FLAG_PLCPFAIL) local->fif_plcpfail++; if (sdata->u.mntr_flags & MONITOR_FLAG_CONTROL) local->fif_control++; if (sdata->u.mntr_flags & MONITOR_FLAG_OTHER_BSS) local->fif_other_bss++; netif_addr_lock_bh(local->mdev); ieee80211_configure_filter(local); netif_addr_unlock_bh(local->mdev); break; case IEEE80211_IF_TYPE_STA: case IEEE80211_IF_TYPE_IBSS: sdata->u.sta.flags &= ~IEEE80211_STA_PREV_BSSID_SET; /* fall through */ default: conf.vif = &sdata->vif; conf.type = sdata->vif.type; conf.mac_addr = dev->dev_addr; res = local->ops->add_interface(local_to_hw(local), &conf); if (res) goto err_stop; if (ieee80211_vif_is_mesh(&sdata->vif)) ieee80211_start_mesh(sdata); changed |= ieee80211_reset_erp_info(sdata); ieee80211_bss_info_change_notify(sdata, changed); ieee80211_enable_keys(sdata); if (sdata->vif.type == IEEE80211_IF_TYPE_STA && !(sdata->flags & IEEE80211_SDATA_USERSPACE_MLME)) netif_carrier_off(dev); else netif_carrier_on(dev); } if (sdata->vif.type == IEEE80211_IF_TYPE_WDS) { /* Create STA entry for the WDS peer */ sta = sta_info_alloc(sdata, sdata->u.wds.remote_addr, GFP_KERNEL); if (!sta) { res = -ENOMEM; goto err_del_interface; } /* no locking required since STA is not live yet */ sta->flags |= WLAN_STA_AUTHORIZED; res = sta_info_insert(sta); if (res) { /* STA has been freed */ goto err_del_interface; } } if (local->open_count == 0) { res = dev_open(local->mdev); WARN_ON(res); if (res) goto err_del_interface; tasklet_enable(&local->tx_pending_tasklet); tasklet_enable(&local->tasklet); } /* * set_multicast_list will be invoked by the networking core * which will check whether any increments here were done in * error and sync them down to the hardware as filter flags. */ if (sdata->flags & IEEE80211_SDATA_ALLMULTI) atomic_inc(&local->iff_allmultis); if (sdata->flags & IEEE80211_SDATA_PROMISC) atomic_inc(&local->iff_promiscs); local->open_count++; if (need_hw_reconfig) { ieee80211_hw_config(local); /* * set default queue parameters so drivers don't * need to initialise the hardware if the hardware * doesn't start up with sane defaults */ ieee80211_set_wmm_default(sdata); } /* * ieee80211_sta_work is disabled while network interface * is down. Therefore, some configuration changes may not * yet be effective. Trigger execution of ieee80211_sta_work * to fix this. */ if (sdata->vif.type == IEEE80211_IF_TYPE_STA || sdata->vif.type == IEEE80211_IF_TYPE_IBSS) { struct ieee80211_if_sta *ifsta = &sdata->u.sta; queue_work(local->hw.workqueue, &ifsta->work); } netif_tx_start_all_queues(dev); return 0; err_del_interface: local->ops->remove_interface(local_to_hw(local), &conf); err_stop: if (!local->open_count && local->ops->stop) local->ops->stop(local_to_hw(local)); err_del_bss: sdata->bss = NULL; if (sdata->vif.type == IEEE80211_IF_TYPE_VLAN) list_del(&sdata->u.vlan.list); return res; } static int ieee80211_stop(struct net_device *dev) { struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev); struct ieee80211_local *local = sdata->local; struct ieee80211_if_init_conf conf; struct sta_info *sta; /* * Stop TX on this interface first. */ netif_tx_stop_all_queues(dev); /* * Now delete all active aggregation sessions. */ rcu_read_lock(); list_for_each_entry_rcu(sta, &local->sta_list, list) { if (sta->sdata == sdata) ieee80211_sta_tear_down_BA_sessions(sdata, sta->addr); } rcu_read_unlock(); /* * Remove all stations associated with this interface. * * This must be done before calling ops->remove_interface() * because otherwise we can later invoke ops->sta_notify() * whenever the STAs are removed, and that invalidates driver * assumptions about always getting a vif pointer that is valid * (because if we remove a STA after ops->remove_interface() * the driver will have removed the vif info already!) * * We could relax this and only unlink the stations from the * hash table and list but keep them on a per-sdata list that * will be inserted back again when the interface is brought * up again, but I don't currently see a use case for that, * except with WDS which gets a STA entry created when it is * brought up. */ sta_info_flush(local, sdata); /* * Don't count this interface for promisc/allmulti while it * is down. dev_mc_unsync() will invoke set_multicast_list * on the master interface which will sync these down to the * hardware as filter flags. */ if (sdata->flags & IEEE80211_SDATA_ALLMULTI) atomic_dec(&local->iff_allmultis); if (sdata->flags & IEEE80211_SDATA_PROMISC) atomic_dec(&local->iff_promiscs); dev_mc_unsync(local->mdev, dev); /* APs need special treatment */ if (sdata->vif.type == IEEE80211_IF_TYPE_AP) { struct ieee80211_sub_if_data *vlan, *tmp; struct beacon_data *old_beacon = sdata->u.ap.beacon; /* remove beacon */ rcu_assign_pointer(sdata->u.ap.beacon, NULL); synchronize_rcu(); kfree(old_beacon); /* down all dependent devices, that is VLANs */ list_for_each_entry_safe(vlan, tmp, &sdata->u.ap.vlans, u.vlan.list) dev_close(vlan->dev); WARN_ON(!list_empty(&sdata->u.ap.vlans)); } local->open_count--; switch (sdata->vif.type) { case IEEE80211_IF_TYPE_VLAN: list_del(&sdata->u.vlan.list); /* no need to tell driver */ break; case IEEE80211_IF_TYPE_MNTR: if (sdata->u.mntr_flags & MONITOR_FLAG_COOK_FRAMES) { local->cooked_mntrs--; break; } local->monitors--; if (local->monitors == 0) local->hw.conf.flags &= ~IEEE80211_CONF_RADIOTAP; if (sdata->u.mntr_flags & MONITOR_FLAG_FCSFAIL) local->fif_fcsfail--; if (sdata->u.mntr_flags & MONITOR_FLAG_PLCPFAIL) local->fif_plcpfail--; if (sdata->u.mntr_flags & MONITOR_FLAG_CONTROL) local->fif_control--; if (sdata->u.mntr_flags & MONITOR_FLAG_OTHER_BSS) local->fif_other_bss--; netif_addr_lock_bh(local->mdev); ieee80211_configure_filter(local); netif_addr_unlock_bh(local->mdev); break; case IEEE80211_IF_TYPE_STA: case IEEE80211_IF_TYPE_IBSS: sdata->u.sta.state = IEEE80211_STA_MLME_DISABLED; memset(sdata->u.sta.bssid, 0, ETH_ALEN); del_timer_sync(&sdata->u.sta.timer); /* * When we get here, the interface is marked down. * Call synchronize_rcu() to wait for the RX path * should it be using the interface and enqueuing * frames at this very time on another CPU. */ synchronize_rcu(); skb_queue_purge(&sdata->u.sta.skb_queue); if (local->scan_sdata == sdata) { if (!local->ops->hw_scan) { local->sta_sw_scanning = 0; cancel_delayed_work(&local->scan_work); } else local->sta_hw_scanning = 0; } sdata->u.sta.flags &= ~IEEE80211_STA_PRIVACY_INVOKED; kfree(sdata->u.sta.extra_ie); sdata->u.sta.extra_ie = NULL; sdata->u.sta.extra_ie_len = 0; /* fall through */ case IEEE80211_IF_TYPE_MESH_POINT: if (ieee80211_vif_is_mesh(&sdata->vif)) { /* allmulti is always set on mesh ifaces */ atomic_dec(&local->iff_allmultis); ieee80211_stop_mesh(sdata); } /* fall through */ default: conf.vif = &sdata->vif; conf.type = sdata->vif.type; conf.mac_addr = dev->dev_addr; /* disable all keys for as long as this netdev is down */ ieee80211_disable_keys(sdata); local->ops->remove_interface(local_to_hw(local), &conf); } sdata->bss = NULL; if (local->open_count == 0) { if (netif_running(local->mdev)) dev_close(local->mdev); if (local->ops->stop) local->ops->stop(local_to_hw(local)); ieee80211_led_radio(local, 0); flush_workqueue(local->hw.workqueue); tasklet_disable(&local->tx_pending_tasklet); tasklet_disable(&local->tasklet); } return 0; } static void ieee80211_set_multicast_list(struct net_device *dev) { struct ieee80211_local *local = wdev_priv(dev->ieee80211_ptr); struct ieee80211_sub_if_data *sdata = IEEE80211_DEV_TO_SUB_IF(dev); int allmulti, promisc, sdata_allmulti, sdata_promisc; allmulti = !!(dev->flags & IFF_ALLMULTI); promisc = !!(dev->flags & IFF_PROMISC); sdata_allmulti = !!(sdata->flags & IEEE80211_SDATA_ALLMULTI); sdata_promisc = !!(sdata->flags & IEEE80211_SDATA_PROMISC); if (allmulti != sdata_allmulti) { if (dev->flags & IFF_ALLMULTI) atomic_inc(&local->iff_allmultis); else atomic_dec(&local->iff_allmultis); sdata->flags ^= IEEE80211_SDATA_ALLMULTI; } if (promisc != sdata_promisc) { if (dev->flags & IFF_PROMISC) atomic_inc(&local->iff_promiscs); else atomic_dec(&local->iff_promiscs); sdata->flags ^= IEEE80211_SDATA_PROMISC; } dev_mc_sync(local->mdev, dev); } static const struct header_ops ieee80211_header_ops = { .create = eth_header, .parse = header_parse_80211, .rebuild = eth_rebuild_header, .cache = eth_header_cache, .cache_update = eth_header_cache_update, }; void ieee80211_if_setup(struct net_device *dev) { ether_setup(dev); dev->hard_start_xmit = ieee80211_subif_start_xmit; dev->wireless_handlers = &ieee80211_iw_handler_def; dev->set_multicast_list = ieee80211_set_multicast_list; dev->change_mtu = ieee80211_change_mtu; dev->open = ieee80211_open; dev->stop = ieee80211_stop; dev->destructor = free_netdev; /* we will validate the address ourselves in ->open */ dev->validate_addr = NULL; } /* everything else */ int ieee80211_if_config(struct ieee80211_sub_if_data *sdata, u32 changed) { struct ieee80211_local *local = sdata->local; struct ieee80211_if_conf conf; if (WARN_ON(!netif_running(sdata->dev))) return 0; if (!local->ops->config_interface) return 0; memset(&conf, 0, sizeof(conf)); conf.changed = changed; if (sdata->vif.type == IEEE80211_IF_TYPE_STA || sdata->vif.type == IEEE80211_IF_TYPE_IBSS) { conf.bssid = sdata->u.sta.bssid; conf.ssid = sdata->u.sta.ssid; conf.ssid_len = sdata->u.sta.ssid_len; } else if (sdata->vif.type == IEEE80211_IF_TYPE_AP) { conf.bssid = sdata->dev->dev_addr; conf.ssid = sdata->u.ap.ssid; conf.ssid_len = sdata->u.ap.ssid_len; } else if (ieee80211_vif_is_mesh(&sdata->vif)) { u8 zero[ETH_ALEN] = { 0 }; conf.bssid = zero; conf.ssid = zero; conf.ssid_len = 0; } else { WARN_ON(1); return -EINVAL; } if (WARN_ON(!conf.bssid && (changed & IEEE80211_IFCC_BSSID))) return -EINVAL; if (WARN_ON(!conf.ssid && (changed & IEEE80211_IFCC_SSID))) return -EINVAL; return local->ops->config_interface(local_to_hw(local), &sdata->vif, &conf); } int ieee80211_hw_config(struct ieee80211_local *local) { struct ieee80211_channel *chan; int ret = 0; if (local->sta_sw_scanning) chan = local->scan_channel; else chan = local->oper_channel; local->hw.conf.channel = chan; if (!local->hw.conf.power_level) local->hw.conf.power_level = chan->max_power; else local->hw.conf.power_level = min(chan->max_power, local->hw.conf.power_level); local->hw.conf.max_antenna_gain = chan->max_antenna_gain; #ifdef CONFIG_MAC80211_VERBOSE_DEBUG printk(KERN_DEBUG "%s: HW CONFIG: freq=%d\n", wiphy_name(local->hw.wiphy), chan->center_freq); #endif if (local->open_count) ret = local->ops->config(local_to_hw(local), &local->hw.conf); return ret; } /** * ieee80211_handle_ht should be used only after legacy configuration * has been determined namely band, as ht configuration depends upon * the hardware's HT abilities for a _specific_ band. */ u32 ieee80211_handle_ht(struct ieee80211_local *local, int enable_ht, struct ieee80211_ht_info *req_ht_cap, struct ieee80211_ht_bss_info *req_bss_cap) { struct ieee80211_conf *conf = &local->hw.conf; struct ieee80211_supported_band *sband; struct ieee80211_ht_info ht_conf; struct ieee80211_ht_bss_info ht_bss_conf; u32 changed = 0; int i; u8 max_tx_streams = IEEE80211_HT_CAP_MAX_STREAMS; u8 tx_mcs_set_cap; sband = local->hw.wiphy->bands[conf->channel->band]; memset(&ht_conf, 0, sizeof(struct ieee80211_ht_info)); memset(&ht_bss_conf, 0, sizeof(struct ieee80211_ht_bss_info)); /* HT is not supported */ if (!sband->ht_info.ht_supported) { conf->flags &= ~IEEE80211_CONF_SUPPORT_HT_MODE; goto out; } /* disable HT */ if (!enable_ht) { if (conf->flags & IEEE80211_CONF_SUPPORT_HT_MODE) changed |= BSS_CHANGED_HT; conf->flags &= ~IEEE80211_CONF_SUPPORT_HT_MODE; conf->ht_conf.ht_supported = 0; goto out; } if (!(conf->flags & IEEE80211_CONF_SUPPORT_HT_MODE)) changed |= BSS_CHANGED_HT; conf->flags |= IEEE80211_CONF_SUPPORT_HT_MODE; ht_conf.ht_supported = 1; ht_conf.cap = req_ht_cap->cap & sband->ht_info.cap; ht_conf.cap &= ~(IEEE80211_HT_CAP_SM_PS); ht_conf.cap |= sband->ht_info.cap & IEEE80211_HT_CAP_SM_PS; ht_bss_conf.primary_channel = req_bss_cap->primary_channel; ht_bss_conf.bss_cap = req_bss_cap->bss_cap; ht_bss_conf.bss_op_mode = req_bss_cap->bss_op_mode; ht_conf.ampdu_factor = req_ht_cap->ampdu_factor; ht_conf.ampdu_density = req_ht_cap->ampdu_density; /* Bits 96-100 */ tx_mcs_set_cap = sband->ht_info.supp_mcs_set[12]; /* configure suppoerted Tx MCS according to requested MCS * (based in most cases on Rx capabilities of peer) and self * Tx MCS capabilities (as defined by low level driver HW * Tx capabilities) */ if (!(tx_mcs_set_cap & IEEE80211_HT_CAP_MCS_TX_DEFINED)) goto check_changed; /* Counting from 0 therfore + 1 */ if (tx_mcs_set_cap & IEEE80211_HT_CAP_MCS_TX_RX_DIFF) max_tx_streams = ((tx_mcs_set_cap & IEEE80211_HT_CAP_MCS_TX_STREAMS) >> 2) + 1; for (i = 0; i < max_tx_streams; i++) ht_conf.supp_mcs_set[i] = sband->ht_info.supp_mcs_set[i] & req_ht_cap->supp_mcs_set[i]; if (tx_mcs_set_cap & IEEE80211_HT_CAP_MCS_TX_UEQM) for (i = IEEE80211_SUPP_MCS_SET_UEQM; i < IEEE80211_SUPP_MCS_SET_LEN; i++) ht_conf.supp_mcs_set[i] = sband->ht_info.supp_mcs_set[i] & req_ht_cap->supp_mcs_set[i]; check_changed: /* if bss configuration changed store the new one */ if (memcmp(&conf->ht_conf, &ht_conf, sizeof(ht_conf)) || memcmp(&conf->ht_bss_conf, &ht_bss_conf, sizeof(ht_bss_conf))) { changed |= BSS_CHANGED_HT; memcpy(&conf->ht_conf, &ht_conf, sizeof(ht_conf)); memcpy(&conf->ht_bss_conf, &ht_bss_conf, sizeof(ht_bss_conf)); } out: return changed; } void ieee80211_bss_info_change_notify(struct ieee80211_sub_if_data *sdata, u32 changed) { struct ieee80211_local *local = sdata->local; if (!changed) return; if (local->ops->bss_info_changed) local->ops->bss_info_changed(local_to_hw(local), &sdata->vif, &sdata->bss_conf, changed); } u32 ieee80211_reset_erp_info(struct ieee80211_sub_if_data *sdata) { sdata->bss_conf.use_cts_prot = 0; sdata->bss_conf.use_short_preamble = 0; return BSS_CHANGED_ERP_CTS_PROT | BSS_CHANGED_ERP_PREAMBLE; } void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw, struct sk_buff *skb) { struct ieee80211_local *local = hw_to_local(hw); struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); int tmp; skb->dev = local->mdev; skb->pkt_type = IEEE80211_TX_STATUS_MSG; skb_queue_tail(info->flags & IEEE80211_TX_CTL_REQ_TX_STATUS ? &local->skb_queue : &local->skb_queue_unreliable, skb); tmp = skb_queue_len(&local->skb_queue) + skb_queue_len(&local->skb_queue_unreliable); while (tmp > IEEE80211_IRQSAFE_QUEUE_LIMIT && (skb = skb_dequeue(&local->skb_queue_unreliable))) { dev_kfree_skb_irq(skb); tmp--; I802_DEBUG_INC(local->tx_status_drop); } tasklet_schedule(&local->tasklet); } EXPORT_SYMBOL(ieee80211_tx_status_irqsafe); static void ieee80211_tasklet_handler(unsigned long data) { struct ieee80211_local *local = (struct ieee80211_local *) data; struct sk_buff *skb; struct ieee80211_rx_status rx_status; struct ieee80211_ra_tid *ra_tid; while ((skb = skb_dequeue(&local->skb_queue)) || (skb = skb_dequeue(&local->skb_queue_unreliable))) { switch (skb->pkt_type) { case IEEE80211_RX_MSG: /* status is in skb->cb */ memcpy(&rx_status, skb->cb, sizeof(rx_status)); /* Clear skb->pkt_type in order to not confuse kernel * netstack. */ skb->pkt_type = 0; __ieee80211_rx(local_to_hw(local), skb, &rx_status); break; case IEEE80211_TX_STATUS_MSG: skb->pkt_type = 0; ieee80211_tx_status(local_to_hw(local), skb); break; case IEEE80211_DELBA_MSG: ra_tid = (struct ieee80211_ra_tid *) &skb->cb; ieee80211_stop_tx_ba_cb(local_to_hw(local), ra_tid->ra, ra_tid->tid); dev_kfree_skb(skb); break; case IEEE80211_ADDBA_MSG: ra_tid = (struct ieee80211_ra_tid *) &skb->cb; ieee80211_start_tx_ba_cb(local_to_hw(local), ra_tid->ra, ra_tid->tid); dev_kfree_skb(skb); break ; default: WARN_ON(1); dev_kfree_skb(skb); break; } } } /* Remove added headers (e.g., QoS control), encryption header/MIC, etc. to * make a prepared TX frame (one that has been given to hw) to look like brand * new IEEE 802.11 frame that is ready to go through TX processing again. */ static void ieee80211_remove_tx_extra(struct ieee80211_local *local, struct ieee80211_key *key, struct sk_buff *skb) { unsigned int hdrlen, iv_len, mic_len; struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data; hdrlen = ieee80211_hdrlen(hdr->frame_control); if (!key) goto no_key; switch (key->conf.alg) { case ALG_WEP: iv_len = WEP_IV_LEN; mic_len = WEP_ICV_LEN; break; case ALG_TKIP: iv_len = TKIP_IV_LEN; mic_len = TKIP_ICV_LEN; break; case ALG_CCMP: iv_len = CCMP_HDR_LEN; mic_len = CCMP_MIC_LEN; break; default: goto no_key; } if (skb->len >= hdrlen + mic_len && !(key->flags & KEY_FLAG_UPLOADED_TO_HARDWARE)) skb_trim(skb, skb->len - mic_len); if (skb->len >= hdrlen + iv_len) { memmove(skb->data + iv_len, skb->data, hdrlen); hdr = (struct ieee80211_hdr *)skb_pull(skb, iv_len); } no_key: if (ieee80211_is_data_qos(hdr->frame_control)) { hdr->frame_control &= ~cpu_to_le16(IEEE80211_STYPE_QOS_DATA); memmove(skb->data + IEEE80211_QOS_CTL_LEN, skb->data, hdrlen - IEEE80211_QOS_CTL_LEN); skb_pull(skb, IEEE80211_QOS_CTL_LEN); } } static void ieee80211_handle_filtered_frame(struct ieee80211_local *local, struct sta_info *sta, struct sk_buff *skb) { struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); sta->tx_filtered_count++; /* * Clear the TX filter mask for this STA when sending the next * packet. If the STA went to power save mode, this will happen * when it wakes up for the next time. */ set_sta_flags(sta, WLAN_STA_CLEAR_PS_FILT); /* * This code races in the following way: * * (1) STA sends frame indicating it will go to sleep and does so * (2) hardware/firmware adds STA to filter list, passes frame up * (3) hardware/firmware processes TX fifo and suppresses a frame * (4) we get TX status before having processed the frame and * knowing that the STA has gone to sleep. * * This is actually quite unlikely even when both those events are * processed from interrupts coming in quickly after one another or * even at the same time because we queue both TX status events and * RX frames to be processed by a tasklet and process them in the * same order that they were received or TX status last. Hence, there * is no race as long as the frame RX is processed before the next TX * status, which drivers can ensure, see below. * * Note that this can only happen if the hardware or firmware can * actually add STAs to the filter list, if this is done by the * driver in response to set_tim() (which will only reduce the race * this whole filtering tries to solve, not completely solve it) * this situation cannot happen. * * To completely solve this race drivers need to make sure that they * (a) don't mix the irq-safe/not irq-safe TX status/RX processing * functions and * (b) always process RX events before TX status events if ordering * can be unknown, for example with different interrupt status * bits. */ if (test_sta_flags(sta, WLAN_STA_PS) && skb_queue_len(&sta->tx_filtered) < STA_MAX_TX_BUFFER) { ieee80211_remove_tx_extra(local, sta->key, skb); skb_queue_tail(&sta->tx_filtered, skb); return; } if (!test_sta_flags(sta, WLAN_STA_PS) && !(info->flags & IEEE80211_TX_CTL_REQUEUE)) { /* Software retry the packet once */ info->flags |= IEEE80211_TX_CTL_REQUEUE; ieee80211_remove_tx_extra(local, sta->key, skb); dev_queue_xmit(skb); return; } #ifdef CONFIG_MAC80211_VERBOSE_DEBUG if (net_ratelimit()) printk(KERN_DEBUG "%s: dropped TX filtered frame, " "queue_len=%d PS=%d @%lu\n", wiphy_name(local->hw.wiphy), skb_queue_len(&sta->tx_filtered), !!test_sta_flags(sta, WLAN_STA_PS), jiffies); #endif dev_kfree_skb(skb); } void ieee80211_tx_status(struct ieee80211_hw *hw, struct sk_buff *skb) { struct sk_buff *skb2; struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data; struct ieee80211_local *local = hw_to_local(hw); struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); u16 frag, type; __le16 fc; struct ieee80211_tx_status_rtap_hdr *rthdr; struct ieee80211_sub_if_data *sdata; struct net_device *prev_dev = NULL; struct sta_info *sta; rcu_read_lock(); if (info->status.excessive_retries) { sta = sta_info_get(local, hdr->addr1); if (sta) { if (test_sta_flags(sta, WLAN_STA_PS)) { /* * The STA is in power save mode, so assume * that this TX packet failed because of that. */ ieee80211_handle_filtered_frame(local, sta, skb); rcu_read_unlock(); return; } } } fc = hdr->frame_control; if ((info->flags & IEEE80211_TX_STAT_AMPDU_NO_BACK) && (ieee80211_is_data_qos(fc))) { u16 tid, ssn; u8 *qc; sta = sta_info_get(local, hdr->addr1); if (sta) { qc = ieee80211_get_qos_ctl(hdr); tid = qc[0] & 0xf; ssn = ((le16_to_cpu(hdr->seq_ctrl) + 0x10) & IEEE80211_SCTL_SEQ); ieee80211_send_bar(sta->sdata, hdr->addr1, tid, ssn); } } if (info->flags & IEEE80211_TX_STAT_TX_FILTERED) { sta = sta_info_get(local, hdr->addr1); if (sta) { ieee80211_handle_filtered_frame(local, sta, skb); rcu_read_unlock(); return; } } else rate_control_tx_status(local->mdev, skb); rcu_read_unlock(); ieee80211_led_tx(local, 0); /* SNMP counters * Fragments are passed to low-level drivers as separate skbs, so these * are actually fragments, not frames. Update frame counters only for * the first fragment of the frame. */ frag = le16_to_cpu(hdr->seq_ctrl) & IEEE80211_SCTL_FRAG; type = le16_to_cpu(hdr->frame_control) & IEEE80211_FCTL_FTYPE; if (info->flags & IEEE80211_TX_STAT_ACK) { if (frag == 0) { local->dot11TransmittedFrameCount++; if (is_multicast_ether_addr(hdr->addr1)) local->dot11MulticastTransmittedFrameCount++; if (info->status.retry_count > 0) local->dot11RetryCount++; if (info->status.retry_count > 1) local->dot11MultipleRetryCount++; } /* This counter shall be incremented for an acknowledged MPDU * with an individual address in the address 1 field or an MPDU * with a multicast address in the address 1 field of type Data * or Management. */ if (!is_multicast_ether_addr(hdr->addr1) || type == IEEE80211_FTYPE_DATA || type == IEEE80211_FTYPE_MGMT) local->dot11TransmittedFragmentCount++; } else { if (frag == 0) local->dot11FailedCount++; } /* this was a transmitted frame, but now we want to reuse it */ skb_orphan(skb); /* * This is a bit racy but we can avoid a lot of work * with this test... */ if (!local->monitors && !local->cooked_mntrs) { dev_kfree_skb(skb); return; } /* send frame to monitor interfaces now */ if (skb_headroom(skb) < sizeof(*rthdr)) { printk(KERN_ERR "ieee80211_tx_status: headroom too small\n"); dev_kfree_skb(skb); return; } rthdr = (struct ieee80211_tx_status_rtap_hdr *) skb_push(skb, sizeof(*rthdr)); memset(rthdr, 0, sizeof(*rthdr)); rthdr->hdr.it_len = cpu_to_le16(sizeof(*rthdr)); rthdr->hdr.it_present = cpu_to_le32((1 << IEEE80211_RADIOTAP_TX_FLAGS) | (1 << IEEE80211_RADIOTAP_DATA_RETRIES)); if (!(info->flags & IEEE80211_TX_STAT_ACK) && !is_multicast_ether_addr(hdr->addr1)) rthdr->tx_flags |= cpu_to_le16(IEEE80211_RADIOTAP_F_TX_FAIL); if ((info->flags & IEEE80211_TX_CTL_USE_RTS_CTS) && (info->flags & IEEE80211_TX_CTL_USE_CTS_PROTECT)) rthdr->tx_flags |= cpu_to_le16(IEEE80211_RADIOTAP_F_TX_CTS); else if (info->flags & IEEE80211_TX_CTL_USE_RTS_CTS) rthdr->tx_flags |= cpu_to_le16(IEEE80211_RADIOTAP_F_TX_RTS); rthdr->data_retries = info->status.retry_count; /* XXX: is this sufficient for BPF? */ skb_set_mac_header(skb, 0); skb->ip_summed = CHECKSUM_UNNECESSARY; skb->pkt_type = PACKET_OTHERHOST; skb->protocol = htons(ETH_P_802_2); memset(skb->cb, 0, sizeof(skb->cb)); rcu_read_lock(); list_for_each_entry_rcu(sdata, &local->interfaces, list) { if (sdata->vif.type == IEEE80211_IF_TYPE_MNTR) { if (!netif_running(sdata->dev)) continue; if (prev_dev) { skb2 = skb_clone(skb, GFP_ATOMIC); if (skb2) { skb2->dev = prev_dev; netif_rx(skb2); } } prev_dev = sdata->dev; } } if (prev_dev) { skb->dev = prev_dev; netif_rx(skb); skb = NULL; } rcu_read_unlock(); dev_kfree_skb(skb); } EXPORT_SYMBOL(ieee80211_tx_status); struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len, const struct ieee80211_ops *ops) { struct ieee80211_local *local; int priv_size; struct wiphy *wiphy; /* Ensure 32-byte alignment of our private data and hw private data. * We use the wiphy priv data for both our ieee80211_local and for * the driver's private data * * In memory it'll be like this: * * +-------------------------+ * | struct wiphy | * +-------------------------+ * | struct ieee80211_local | * +-------------------------+ * | driver's private data | * +-------------------------+ * */ priv_size = ((sizeof(struct ieee80211_local) + NETDEV_ALIGN_CONST) & ~NETDEV_ALIGN_CONST) + priv_data_len; wiphy = wiphy_new(&mac80211_config_ops, priv_size); if (!wiphy) return NULL; wiphy->privid = mac80211_wiphy_privid; local = wiphy_priv(wiphy); local->hw.wiphy = wiphy; local->hw.priv = (char *)local + ((sizeof(struct ieee80211_local) + NETDEV_ALIGN_CONST) & ~NETDEV_ALIGN_CONST); BUG_ON(!ops->tx); BUG_ON(!ops->start); BUG_ON(!ops->stop); BUG_ON(!ops->config); BUG_ON(!ops->add_interface); BUG_ON(!ops->remove_interface); BUG_ON(!ops->configure_filter); local->ops = ops; local->hw.queues = 1; /* default */ local->bridge_packets = 1; local->rts_threshold = IEEE80211_MAX_RTS_THRESHOLD; local->fragmentation_threshold = IEEE80211_MAX_FRAG_THRESHOLD; local->short_retry_limit = 7; local->long_retry_limit = 4; local->hw.conf.radio_enabled = 1; INIT_LIST_HEAD(&local->interfaces); spin_lock_init(&local->key_lock); INIT_DELAYED_WORK(&local->scan_work, ieee80211_sta_scan_work); sta_info_init(local); tasklet_init(&local->tx_pending_tasklet, ieee80211_tx_pending, (unsigned long)local); tasklet_disable(&local->tx_pending_tasklet); tasklet_init(&local->tasklet, ieee80211_tasklet_handler, (unsigned long) local); tasklet_disable(&local->tasklet); skb_queue_head_init(&local->skb_queue); skb_queue_head_init(&local->skb_queue_unreliable); return local_to_hw(local); } EXPORT_SYMBOL(ieee80211_alloc_hw); int ieee80211_register_hw(struct ieee80211_hw *hw) { struct ieee80211_local *local = hw_to_local(hw); const char *name; int result; enum ieee80211_band band; struct net_device *mdev; struct wireless_dev *mwdev; /* * generic code guarantees at least one band, * set this very early because much code assumes * that hw.conf.channel is assigned */ for (band = 0; band < IEEE80211_NUM_BANDS; band++) { struct ieee80211_supported_band *sband; sband = local->hw.wiphy->bands[band]; if (sband) { /* init channel we're on */ local->hw.conf.channel = local->oper_channel = local->scan_channel = &sband->channels[0]; break; } } /* if low-level driver supports AP, we also support VLAN */ if (local->hw.wiphy->interface_modes & BIT(NL80211_IFTYPE_AP)) local->hw.wiphy->interface_modes |= BIT(NL80211_IFTYPE_AP_VLAN); /* mac80211 always supports monitor */ local->hw.wiphy->interface_modes |= BIT(NL80211_IFTYPE_MONITOR); result = wiphy_register(local->hw.wiphy); if (result < 0) return result; /* * We use the number of queues for feature tests (QoS, HT) internally * so restrict them appropriately. */ if (hw->queues > IEEE80211_MAX_QUEUES) hw->queues = IEEE80211_MAX_QUEUES; if (hw->ampdu_queues > IEEE80211_MAX_AMPDU_QUEUES) hw->ampdu_queues = IEEE80211_MAX_AMPDU_QUEUES; if (hw->queues < 4) hw->ampdu_queues = 0; mdev = alloc_netdev_mq(sizeof(struct wireless_dev), "wmaster%d", ether_setup, ieee80211_num_queues(hw)); if (!mdev) goto fail_mdev_alloc; mwdev = netdev_priv(mdev); mdev->ieee80211_ptr = mwdev; mwdev->wiphy = local->hw.wiphy; local->mdev = mdev; ieee80211_rx_bss_list_init(local); mdev->hard_start_xmit = ieee80211_master_start_xmit; mdev->open = ieee80211_master_open; mdev->stop = ieee80211_master_stop; mdev->type = ARPHRD_IEEE80211; mdev->header_ops = &ieee80211_header_ops; mdev->set_multicast_list = ieee80211_master_set_multicast_list; name = wiphy_dev(local->hw.wiphy)->driver->name; local->hw.workqueue = create_freezeable_workqueue(name); if (!local->hw.workqueue) { result = -ENOMEM; goto fail_workqueue; } /* * The hardware needs headroom for sending the frame, * and we need some headroom for passing the frame to monitor * interfaces, but never both at the same time. */ local->tx_headroom = max_t(unsigned int , local->hw.extra_tx_headroom, sizeof(struct ieee80211_tx_status_rtap_hdr)); debugfs_hw_add(local); if (local->hw.conf.beacon_int < 10) local->hw.conf.beacon_int = 100; if (local->hw.max_listen_interval == 0) local->hw.max_listen_interval = 1; local->hw.conf.listen_interval = local->hw.max_listen_interval; local->wstats_flags |= local->hw.flags & (IEEE80211_HW_SIGNAL_UNSPEC | IEEE80211_HW_SIGNAL_DB | IEEE80211_HW_SIGNAL_DBM) ? IW_QUAL_QUAL_UPDATED : IW_QUAL_QUAL_INVALID; local->wstats_flags |= local->hw.flags & IEEE80211_HW_NOISE_DBM ? IW_QUAL_NOISE_UPDATED : IW_QUAL_NOISE_INVALID; if (local->hw.flags & IEEE80211_HW_SIGNAL_DBM) local->wstats_flags |= IW_QUAL_DBM; result = sta_info_start(local); if (result < 0) goto fail_sta_info; rtnl_lock(); result = dev_alloc_name(local->mdev, local->mdev->name); if (result < 0) goto fail_dev; memcpy(local->mdev->dev_addr, local->hw.wiphy->perm_addr, ETH_ALEN); SET_NETDEV_DEV(local->mdev, wiphy_dev(local->hw.wiphy)); result = register_netdevice(local->mdev); if (result < 0) goto fail_dev; result = ieee80211_init_rate_ctrl_alg(local, hw->rate_control_algorithm); if (result < 0) { printk(KERN_DEBUG "%s: Failed to initialize rate control " "algorithm\n", wiphy_name(local->hw.wiphy)); goto fail_rate; } result = ieee80211_wep_init(local); if (result < 0) { printk(KERN_DEBUG "%s: Failed to initialize wep: %d\n", wiphy_name(local->hw.wiphy), result); goto fail_wep; } local->mdev->select_queue = ieee80211_select_queue; /* add one default STA interface */ result = ieee80211_if_add(local, "wlan%d", NULL, IEEE80211_IF_TYPE_STA, NULL); if (result) printk(KERN_WARNING "%s: Failed to add default virtual iface\n", wiphy_name(local->hw.wiphy)); rtnl_unlock(); ieee80211_led_init(local); return 0; fail_wep: rate_control_deinitialize(local); fail_rate: unregister_netdevice(local->mdev); local->mdev = NULL; fail_dev: rtnl_unlock(); sta_info_stop(local); fail_sta_info: debugfs_hw_del(local); destroy_workqueue(local->hw.workqueue); fail_workqueue: if (local->mdev) free_netdev(local->mdev); fail_mdev_alloc: wiphy_unregister(local->hw.wiphy); return result; } EXPORT_SYMBOL(ieee80211_register_hw); void ieee80211_unregister_hw(struct ieee80211_hw *hw) { struct ieee80211_local *local = hw_to_local(hw); tasklet_kill(&local->tx_pending_tasklet); tasklet_kill(&local->tasklet); rtnl_lock(); /* * At this point, interface list manipulations are fine * because the driver cannot be handing us frames any * more and the tasklet is killed. */ /* First, we remove all virtual interfaces. */ ieee80211_remove_interfaces(local); /* then, finally, remove the master interface */ unregister_netdevice(local->mdev); rtnl_unlock(); ieee80211_rx_bss_list_deinit(local); ieee80211_clear_tx_pending(local); sta_info_stop(local); rate_control_deinitialize(local); debugfs_hw_del(local); if (skb_queue_len(&local->skb_queue) || skb_queue_len(&local->skb_queue_unreliable)) printk(KERN_WARNING "%s: skb_queue not empty\n", wiphy_name(local->hw.wiphy)); skb_queue_purge(&local->skb_queue); skb_queue_purge(&local->skb_queue_unreliable); destroy_workqueue(local->hw.workqueue); wiphy_unregister(local->hw.wiphy); ieee80211_wep_free(local); ieee80211_led_exit(local); free_netdev(local->mdev); } EXPORT_SYMBOL(ieee80211_unregister_hw); void ieee80211_free_hw(struct ieee80211_hw *hw) { struct ieee80211_local *local = hw_to_local(hw); wiphy_free(local->hw.wiphy); } EXPORT_SYMBOL(ieee80211_free_hw); static int __init ieee80211_init(void) { struct sk_buff *skb; int ret; BUILD_BUG_ON(sizeof(struct ieee80211_tx_info) > sizeof(skb->cb)); BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, driver_data) + IEEE80211_TX_INFO_DRIVER_DATA_SIZE > sizeof(skb->cb)); ret = rc80211_pid_init(); if (ret) return ret; ieee80211_debugfs_netdev_init(); return 0; } static void __exit ieee80211_exit(void) { rc80211_pid_exit(); /* * For key todo, it'll be empty by now but the work * might still be scheduled. */ flush_scheduled_work(); if (mesh_allocated) ieee80211s_stop(); ieee80211_debugfs_netdev_exit(); } subsys_initcall(ieee80211_init); module_exit(ieee80211_exit); MODULE_DESCRIPTION("IEEE 802.11 subsystem"); MODULE_LICENSE("GPL");