/* * Copyright (C) ST-Ericsson SA 2010 * * License Terms: GNU General Public License, version 2 * Author: Rabin Vincent for ST-Ericsson */ #ifndef __LINUX_MFD_STMPE_H #define __LINUX_MFD_STMPE_H #include enum stmpe_block { STMPE_BLOCK_GPIO = 1 << 0, STMPE_BLOCK_KEYPAD = 1 << 1, STMPE_BLOCK_TOUCHSCREEN = 1 << 2, STMPE_BLOCK_ADC = 1 << 3, STMPE_BLOCK_PWM = 1 << 4, STMPE_BLOCK_ROTATOR = 1 << 5, }; enum stmpe_partnum { STMPE811, STMPE1601, STMPE2401, STMPE2403, }; /* * For registers whose locations differ on variants, the correct address is * obtained by indexing stmpe->regs with one of the following. */ enum { STMPE_IDX_CHIP_ID, STMPE_IDX_ICR_LSB, STMPE_IDX_IER_LSB, STMPE_IDX_ISR_MSB, STMPE_IDX_GPMR_LSB, STMPE_IDX_GPSR_LSB, STMPE_IDX_GPCR_LSB, STMPE_IDX_GPDR_LSB, STMPE_IDX_GPEDR_MSB, STMPE_IDX_GPRER_LSB, STMPE_IDX_GPFER_LSB, STMPE_IDX_GPAFR_U_MSB, STMPE_IDX_IEGPIOR_LSB, STMPE_IDX_ISGPIOR_MSB, STMPE_IDX_MAX, }; struct stmpe_variant_info; /** * struct stmpe - STMPE MFD structure * @lock: lock protecting I/O operations * @irq_lock: IRQ bus lock * @dev: device, mostly for dev_dbg() * @i2c: i2c client * @variant: the detected STMPE model number * @regs: list of addresses of registers which are at different addresses on * different variants. Indexed by one of STMPE_IDX_*. * @irq_base: starting IRQ number for internal IRQs * @num_gpios: number of gpios, differs for variants * @ier: cache of IER registers for bus_lock * @oldier: cache of IER registers for bus_lock * @pdata: platform data */ struct stmpe { struct mutex lock; struct mutex irq_lock; struct device *dev; struct i2c_client *i2c; enum stmpe_partnum partnum; struct stmpe_variant_info *variant; const u8 *regs; int irq_base; int num_gpios; u8 ier[2]; u8 oldier[2]; struct stmpe_platform_data *pdata; }; extern int stmpe_reg_write(struct stmpe *stmpe, u8 reg, u8 data); extern int stmpe_reg_read(struct stmpe *stmpe, u8 reg); extern int stmpe_block_read(struct stmpe *stmpe, u8 reg, u8 length, u8 *values); extern int stmpe_block_write(struct stmpe *stmpe, u8 reg, u8 length, const u8 *values); extern int stmpe_set_bits(struct stmpe *stmpe, u8 reg, u8 mask, u8 val); extern int stmpe_set_altfunc(struct stmpe *stmpe, u32 pins, enum stmpe_block block); extern int stmpe_enable(struct stmpe *stmpe, unsigned int blocks); extern int stmpe_disable(struct stmpe *stmpe, unsigned int blocks); struct matrix_keymap_data; /** * struct stmpe_keypad_platform_data - STMPE keypad platform data * @keymap_data: key map table and size * @debounce_ms: debounce interval, in ms. Maximum is * %STMPE_KEYPAD_MAX_DEBOUNCE. * @scan_count: number of key scanning cycles to confirm key data. * Maximum is %STMPE_KEYPAD_MAX_SCAN_COUNT. * @no_autorepeat: disable key autorepeat */ struct stmpe_keypad_platform_data { struct matrix_keymap_data *keymap_data; unsigned int debounce_ms; unsigned int scan_count; bool no_autorepeat; }; /** * struct stmpe_gpio_platform_data - STMPE GPIO platform data * @gpio_base: first gpio number assigned. A maximum of * %STMPE_NR_GPIOS GPIOs will be allocated. */ struct stmpe_gpio_platform_data { int gpio_base; void (*setup)(struct stmpe *stmpe, unsigned gpio_base); void (*remove)(struct stmpe *stmpe, unsigned gpio_base); }; /** * struct stmpe_ts_platform_data - stmpe811 touch screen controller platform * data * @sample_time: ADC converstion time in number of clock. * (0 -> 36 clocks, 1 -> 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks, * 4 -> 80 clocks, 5 -> 96 clocks, 6 -> 144 clocks), * recommended is 4. * @mod_12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC) * @ref_sel: ADC reference source * (0 -> internal reference, 1 -> external reference) * @adc_freq: ADC Clock speed * (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz) * @ave_ctrl: Sample average control * (0 -> 1 sample, 1 -> 2 samples, 2 -> 4 samples, 3 -> 8 samples) * @touch_det_delay: Touch detect interrupt delay * (0 -> 10 us, 1 -> 50 us, 2 -> 100 us, 3 -> 500 us, * 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms) * recommended is 3 * @settling: Panel driver settling time * (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3 -> 1 ms, * 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms) * recommended is 2 * @fraction_z: Length of the fractional part in z * (fraction_z ([0..7]) = Count of the fractional part) * recommended is 7 * @i_drive: current limit value of the touchscreen drivers * (0 -> 20 mA typical 35 mA max, 1 -> 50 mA typical 80 mA max) * * */ struct stmpe_ts_platform_data { u8 sample_time; u8 mod_12b; u8 ref_sel; u8 adc_freq; u8 ave_ctrl; u8 touch_det_delay; u8 settling; u8 fraction_z; u8 i_drive; }; /** * struct stmpe_platform_data - STMPE platform data * @id: device id to distinguish between multiple STMPEs on the same board * @blocks: bitmask of blocks to enable (use STMPE_BLOCK_*) * @irq_trigger: IRQ trigger to use for the interrupt to the host * @irq_invert_polarity: IRQ line is connected with reversed polarity * @irq_base: base IRQ number. %STMPE_NR_IRQS irqs will be used, or * %STMPE_NR_INTERNAL_IRQS if the GPIO driver is not used. * @gpio: GPIO-specific platform data * @keypad: keypad-specific platform data * @ts: touchscreen-specific platform data */ struct stmpe_platform_data { int id; unsigned int blocks; int irq_base; unsigned int irq_trigger; bool irq_invert_polarity; struct stmpe_gpio_platform_data *gpio; struct stmpe_keypad_platform_data *keypad; struct stmpe_ts_platform_data *ts; }; #define STMPE_NR_INTERNAL_IRQS 9 #define STMPE_INT_GPIO(x) (STMPE_NR_INTERNAL_IRQS + (x)) #define STMPE_NR_GPIOS 24 #define STMPE_NR_IRQS STMPE_INT_GPIO(STMPE_NR_GPIOS) #endif