The DEFINE_XENBUS_DRIVER() macro looks a bit weird and causes sparse
errors.

Replace the uses with standard structure definitions instead.  This is
similar to pci and usb device registration.
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>

As the management counters reach a threshold they will generate an
interrupt so the value can be saved and the counter reset. The
current code does not enable this interrupt on all counters. This
can result in inaccurate statistics.

Update the code to enable all the counters to generate an interrupt
when its threshold is exceeded.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Even if the management counters are configured to be 32 bit register
values, the [rt]xoctetcount_gb and [rt]xoctetcount_g counters are
always 64 bit counter registers.  Since they are not being treated as
64 bit values, these statistics are being reported incorrectly (ifconfig,
ethtool, etc.).

Update the routines used to read the registers to access the "hi"
register (an offset of 4 from the "lo" register) to create a 64 bit
value for these 64 bit counters.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch does not affect the 10/100 GRETH MAC.

Before all GBit GRETH TX descriptor ring cleaning was done in
start_xmit(), when descriptor list became full it activated
TX interrupt to start the NAPI rx poll function to do TX ring
cleaning.

With this patch the TX descriptor ring is always cleaned from
the NAPI rx poll function, triggered via TX or RX interrupt.
Otherwise we could end up in TX frames being sent but not
reported to the stack being sent. On the 10/100 GRETH this
is not an issue since the SKB is copied&aligned into private
buffers so that the SKB can be freed directly on start_xmit()
Signed-off-by: NDaniel Hellstrom <daniel@gaisler.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cnic module needs to ensure that if ipv6 support is compiled as a module,
then the cnic module cannot be compiled as built-in as it depends on ipv6.
Made this check cleaner via Kconfig

Use simpler IS_ENABLED for CONFIG_VLAN_8021Q check
Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When 1G SFP RJ45 module is detected, driver must reset the Tx laser
in order to prevent link issues. As part of change, the link_attr_sync
was relocated from vars to params.
Signed-off-by: NYaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This bug was reported on a very old kernel (RHEL6, 2.6.32-491.el6):

BUG: unable to handle kernel paging request at 00800000
IP: [<c04107b5>] nommu_map_page+0x15/0x110
*pdpt = 000000003454f001 *pde = 000000003f03d067
Oops: 0000 [#1] SMP
last sysfs file: /sys/devices/system/cpu/online
Modules linked in: nfsd lockd nfs_acl auth_rpcgss sunrpc exportfs p4_clockmod
ipv6 ppdev parport_pc parport microcode iTCO_wdt iTCO_vendor_support 3c59x mii
dcdbas serio_raw snd_intel8x0 snd_ac97_codec ac97_bus snd_seq snd_seq_device
snd_pcm snd_timer snd soundcore snd_page_alloc i2c_i801 sg lpc_ich mfd_core ext4
jbd2 mbcache sr_mod cdrom sd_mod crc_t10dif pata_acpi ata_generic ata_piix
radeon ttm drm_kms_helper drm i2c_algo_bit i2c_core dm_mirror dm_region_hash
dm_log dm_mod [last unloaded: mperf]

Pid: 4219, comm: nfsd Not tainted 2.6.32-491.el6.i686 #1 Dell Computer
Corporation OptiPlex GX240               /OptiPlex GX240
EIP: 0060:[<c04107b5>] EFLAGS: 00010246 CPU: 0
EIP is at nommu_map_page+0x15/0x110
EAX: 00000000 EBX: c0a83480 ECX: 00000000 EDX: 00800000
ESI: 00000000 EDI: f70e7860 EBP: e2d09b54 ESP: e2d09b24
 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process nfsd (pid: 4219, ti=e2d08000 task=e2ceaaa0 task.ti=e2d08000)
Stack:
 00000056 00000000 0000000e c65efd38 00000020 00000296 00000206 00000206
<0> c050c850 c0a83480 e2cef154 00000001 e2d09ba8 f8fcd585 00000510 00000001
<0> 00000000 00000000 f5172200 f8fdac00 0039ef8c f5277020 f70e7860 00000510
Call Trace:
 [<c050c850>] ? page_address+0xd0/0xe0
 [<f8fcd585>] ? boomerang_start_xmit+0x3b5/0x520 [3c59x]
 [<c07b2975>] ? dev_hard_start_xmit+0xe5/0x400
 [<f9182b00>] ? ip6_output_finish+0x0/0xf0 [ipv6]
 [<c07ca053>] ? sch_direct_xmit+0x113/0x180
 [<c07d5588>] ? nf_hook_slow+0x68/0x120
 [<c07b2ea5>] ? dev_queue_xmit+0x1b5/0x290
 [<f9182b6d>] ? ip6_output_finish+0x6d/0xf0 [ipv6]
 [<f9184cb8>] ? ip6_xmit+0x3e8/0x490 [ipv6]
 [<f91ab9f9>] ? inet6_csk_xmit+0x289/0x2f0 [ipv6]
 [<c07f6451>] ? tcp_transmit_skb+0x431/0x7f0
 [<c07a403f>] ? __alloc_skb+0x4f/0x140
 [<c07f85a2>] ? tcp_write_xmit+0x1c2/0xa50
 [<c07f90b1>] ? __tcp_push_pending_frames+0x31/0xe0
 [<c07ea47a>] ? tcp_sendpage+0x44a/0x4b0
 [<c07ea030>] ? tcp_sendpage+0x0/0x4b0
 [<c079be1e>] ? kernel_sendpage+0x4e/0x90
 [<f8457bb9>] ? svc_send_common+0xc9/0x120 [sunrpc]
 [<f8457c85>] ? svc_sendto+0x75/0x1f0 [sunrpc]
 [<c060d0d9>] ? _atomic_dec_and_lock+0x59/0x90
 [<f87d55d0>] ? nfs3svc_encode_readres+0x0/0xc0 [nfsd]
 [<f845876d>] ? svc_authorise+0x2d/0x40 [sunrpc]
 [<f87d4410>] ? nfs3svc_release_fhandle+0x0/0x10 [nfsd]
 [<f8455721>] ? svc_process_common+0xf1/0x5a0 [sunrpc]
 [<f8457e86>] ? svc_tcp_sendto+0x36/0xa0 [sunrpc]
 [<f8461778>] ? svc_send+0x98/0xd0 [sunrpc]
 [<f87c698c>] ? nfsd+0xac/0x140 [nfsd]
 [<c04470e0>] ? complete+0x40/0x60
 [<f87c68e0>] ? nfsd+0x0/0x140 [nfsd]
 [<c04802ac>] ? kthread+0x7c/0xa0
 [<c0480230>] ? kthread+0x0/0xa0
 [<c0409f9f>] ? kernel_thread_helper+0x7/0x10
Code: 8d b6 00 00 00 00 eb f8 8d b4 26 00 00 00 00 8d bc 27 00 00 00 00 55 89 e5
83 ec 30 89 75 f8 31 f6 89 7d fc 89 c7 89 c8 89 5d f4 <8b> 1a 8b 4d 08 c1 eb 19
c1 e3 04 8b 9b c0 29 c7 c0 83 e3 fc 29

But the problem seems to still exist upstream.  It seems on 32 bit kernels
page_address() can reutrn a NULL value in some circumstances, and the
pci_map_single api isn't prepared to handle that (on this system it results in a
bogus pointer deference in nommu_map_page.

The fix is pretty easy, if we convert the 3c59x driver to use the more
convieient skb_frag_dma_map api we don't need to find the virtual address of the
page at all, and page gets mapped to the hardware properly.  Verified to fix the
problem as described by the reporter.

Applies to the net tree

Change Notes:

v2) Converted PCI_DMA_TODEVICE to DMA_TO_DEVICE.  Thanks Dave!

v3) Actually Run git commit after making changes to v2 :)
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: klassert@mathematik.tu-chemnitz.de
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

They are use less, and may generate compiling warnings, so remove them
(microblaze, arc, arm64, and unicore32 have already defined PCI_IOBASE).

The related warnings (with allmodconfig under microblaze):

  CC [M]  drivers/net/fddi/skfp/skfddi.o
  In file included from drivers/net/fddi/skfp/skfddi.c:95:0:
  drivers/net/fddi/skfp/h/skfbi.h:151:0: warning: "PCI_IOBASE" redefined
   #define PCI_IOBASE 0xffffff00L  /* Bit 31..8:  I/O Base address */
   ^
  In file included from include/linux/io.h:22:0,
                   from include/linux/pci.h:31,
                   from drivers/net/fddi/skfp/skfddi.c:82:
  ./arch/microblaze/include/asm/io.h:33:0: note: this is the location of the previous definition
   #define PCI_IOBASE ((void __iomem *)_IO_BASE)
   ^
Signed-off-by: NChen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should check if the map of the table actually succeeds, and also free
resources accordingly.

Version bumped to 1.2.1.0
Acked-by: NShelley Gong <shelleygong@vmware.com>
Acked-by: NBhavesh Davda <bhavesh@vmware.com>
Signed-off-by: NAndy King <acking@vmware.com>
Reported-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During allocation and initialization of the network driver structures,
the wrong pointer is used to initialize a spin lock. Fix the spin lock
initialization by using the proper pointer.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some hosts can be both little and big endian.
In certain scenarios a big endian kernel can kexec a little endian kernel.

This patch fixes this case from both ends:
1) Return endianity to original values on shutdown (in case little endian kernel boots after we shutdown).
2) Do not rely on HW reset values when loading driver in little endian kernel
   but configure them explicitly (in case previous kernel was big endian and did not reset the HW).
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calxeda 1G/10G XGMAC Ethernet support should be available only on
Calxeda ECX-1000/2000 (Highbank/Midway) platforms.
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Renesas SuperH Ethernet support should be available only on
Renesas ARM SoCs and SuperH architecture.
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a link is already up, the following sequence makes the kernel
block completely:

  ip link set dev eth0 down
  ip link set dev eth0 up

This is because on suspended phy, the following lines

  __lpc_eth_reset(pldat);
  __lpc_eth_init(pldat);

make the LPC ethernet core block (see LPC32x0 manual). The PHY needs to be
(re-)activated low-level first.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch fixes race conditions between PCI error recovery callbacks and
potential ifup/ifdown.

First, if ifup (tg3_open) is called between tg3_io_error_detected() and
tg3_io_resume() then tp->timer is armed twice before expiry. Once during
tg3_open() and again during tg3_io_resume(). This results in BUG
at kernel/time/timer.c:945.

Second, if ifdown (tg3_close) is called between tg3_io_error_detected()
and tg3_io_resume() then tg3_napi_disable() is called twice without
a tg3_napi_enable between. Once during tg3_io_error_detected() and again
during tg3_close(). The tg3_io_resume() then hangs on rtnl_lock().

v2: Added logging messages per Prashant's request

Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Acked-by: NPrashant Sreedharan <prashant@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A couple of RDMA-related called to t4_query_params() were issuing mbox commands
on mbox0 instead of mbox4.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid dumping MPS_RPLC_MAP_CTL for reg dumps; this is a Write-Only register.
Reading this register may cause MPS TCAM corruption.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The adapter firmware can indicate error conditions to the host.
If the firmware has indicated an error, print out the reason for
the firmware error.

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes few register access for both T4 and T5.
PCIE_CORE_UTL_SYSTEM_BUS_AGENT_STATUS & PCIE_CORE_UTL_PCI_EXPRESS_PORT_STATUS
is T4 only register don't let T5 access them. For T5 MA_PARITY_ERROR_STATUS2
is additionally read. MPS_TRC_RSS_CONTROL is T4 only register, for T5 use
MPS_T5_TRC_RSS_CONTROL.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously it was using the length value of serial number.
Also added macro for VPD unique identifier (0x82).
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We previously assumed that a Port's Capabilities and Advertised Capabilities
would never change from Port Initialization time.  This is no longer true
when we can have 10Gb/s and 1Gb/s SFP+ Transceiver Modules randomly swapped.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of the HW is not able to do the receive checksum offloading
the only feature to remove is NETIF_F_RXCSUM.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For new GMACs it is possible to turn-on/off the COE.
In the current driver, when disabled the Rx-checksum
via ethtool, the tool reported that csum was disabled
but the HW continued to set the IPC. Indeed this is
because the fix_features allows this. So the patch
fixes this problem by adding the set_features.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When configuring Tx flow control the Rx queue count was used instead of
the Tx queue count for looping through the Tx hardware queues. Fix the
code to use the Tx queue count.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The debugfs support for the xpcs registers did not properly use the
specified mmd (xpcs_mmd entry) which resulted in the default mmd
value always being used.  Update the debugfs support to generate the
proper mmd register value.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The fifo size reported by the hardware is not correct. Add support
to limit the reported size to what is actually present.  Also, fix
the argument types used in the fifo size calculation function.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The flushing of the Tx hardware queues is only supported at a certain
level of the hardware.  Retrieve the current version of the hardware
and use that to determine if flushing is supported.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If NO_DMA=y:

drivers/built-in.o: In function `xgene_enet_delete_ring':
xgene_enet_main.c:(.text+0x28755a): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `xgene_enet_setup_tx_desc':
xgene_enet_main.c:(.text+0x287774): undefined reference to `dma_map_single'
xgene_enet_main.c:(.text+0x287780): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `xgene_enet_tx_completion':
xgene_enet_main.c:(.text+0x2878e6): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `xgene_enet_refill_bufpool':
xgene_enet_main.c:(.text+0x2879d4): undefined reference to `dma_map_single'
xgene_enet_main.c:(.text+0x2879e0): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `xgene_enet_rx_frame':
xgene_enet_main.c:(.text+0x287aaa): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `xgene_enet_free_desc_ring':
xgene_enet_main.c:(.text+0x287f98): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `xgene_enet_create_desc_ring':
xgene_enet_main.c:(.text+0x28808e): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `xgene_enet_probe':
xgene_enet_main.c:(.text+0x2883d4): undefined reference to `dma_set_mask'
xgene_enet_main.c:(.text+0x2883ec): undefined reference to `dma_supported'
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New firmware on the way.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In case of PLS is active the PLS (PHY Link Status) bit in
the Reg12 has to be set to allow the MAC to asserts the LPI
pattern when the link is ok.
Signed-off-by: Nnandini sharma <nandini.sharma@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to skip the EEE initialisation when the stmmac
is using a switch (with a fixed phy support).
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The value for LPI TW timer has to be updated to 0x1E that is the hardcoded value
of 20.5us and it will apply to all EEE enabled Remote PHYs.
Disadvantage is for PHY's that support lesser wakeup time but we can accept it
waiting to implement LLDP to negotiate the Wakeup time of Remote PHY.
Signed-off-by: Nnandini sharma <nandini.sharma@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to fix the definition of macros for EEE otherwise the LPI TX/RX
entry/exit cannot be properly managed.
Signed-off-by: NNandini Sharma <nandini.sharma@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CONFIG_IWLDVM and CONFIG_IWLMVM currently have a
"depends on m" as its requirement forcing it to be build
as module. This is not needed and thus just remove it.

Fixes: ae7486a2 ("iwlwifi: fix Kconfig issues")
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
[Squashed 2 commites for MVM and DVM]
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This reverts commit 43d826ca.

This commit caused packet loss.

Cc: <stable@vger.kernel.org>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Move the function which we use to set VXLAN DMFS (flow-steering) rules
from mlx4_en to mlx4_core. This refactoring will allow the mlx4_ib driver
to call the helper for the use case of user-space RAW Ethernet QPs, such
that they can serve VXLAN traffic too.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enabling DMA_API_DEBUG, warnings are reported at runtime
because the device driver frees DMA memory with wrong functions
and it does not call dma_mapping_error after mapping dma memory.

The first problem is fixed by of introducing a flag that helps us
keeping track which mapping technique was used, so that we can use
the right API for unmap.
This approach was inspired by the e1000 driver, which uses a similar
technique.
Signed-off-by: NAndre Draszik <andre.draszik@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: NDenis Kirjanov <kda@linux-powerpc.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PTP reference clock, used for setting the addend in the Timestamp Addend
Register, was erroneously hard-coded (as reported in the databook just as
example).

The patch removes the macro named: STMMAC_SYSCLOCK and allows to use a
reference clock (clk_ptp_ref_i) that can be passed from the platform.

If not passed, the main driver clock will be used as default; note that
this can be fine on some platforms.

Note that, prior this patch, using the old STMMAC_SYSCLOCK on some platforms,
as side effect, the ptp clock can move faster/slower than the system clock.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to fix a typo on mmc rx crc error when reported by ethtool.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to w/a a problem that happens on some boxes when run at 10Mbps
Half duplex mode.

During the transmission the CSR signal is asserted for some time and the frames
aborted because of carrier sense error.
This is reported by MMC HW counter: txcarrier signal.
This actually is a false carrier so the frames are good and there is no reason
to ask for dropping them.

This patch so disables the Carrier Sense During Transmission
and this means that the MAC transmitter ignore the CRS signal
during frame transmission in Half-Duplex mode.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: NVince Bridgers <vbridgers2013@gmail.com>
Acked-by: NLey Foon Tan <lftan@altera.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>