The same regulator is used by other chips on the board. The power path is:
VBAT -> TPS63031 - Enable signal is V1_8D regulator -> V3_3D.
V3_3D is used by SD slot and tlv320aic3106 codec as well.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPIO5_8 is used as a mux switch between LCD and HDMI displays. This mux
affects audio routing as well since in LCD mode HDMI audio is not possible
and when HDMI is selected analog audio is not working.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use simple card for audio support on ePOS-EVM.
The audio on the board is: McASP1 <-> tlv320aic3111 codec.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Analog audio is using this codec on the board.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add node for McASP1 along with the needed pinctrl entries.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The VBAT and DCDC4 regulator is needed for audio support (tlv320aic3111)
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPIO2_1 is used as a mux switch between LCD and HDMI displays. This mux
affects audio routing as well since in LCD mode HDMI audio is not possible
and when HDMI is selected analog audio is not working.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The sound support consist only Headset output on the board and can be
handled by "simple-audio-card".
Also enable the Line-In route as the board has support for it.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

When McASP is not in use the pins can be put to sleep mode to conserve
power.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

More and more boards are moving to have audio support via simple-card.
At the same time enable options needed for most am335x and am43xx board for
audio support: McASP and TLV320AIC3X codecs.
The later two has been selected by the CONFIG_SND_AM33XX_SOC_EVM option, but
the aim is to convert all boards to use simple card.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

In addition to the regular mux configuration such as mux mode 1,
2 etc, certain pins of DRA7 require to have "virtual mode" also
programmed. This allows for predefined delay characteristics to
be used by the SoC to meet timing characterstics needed for the
interface.

Provide easy to use macro to do the same.

It is important to note that the official TI guidelines recommend
to do as minimal pin reconfiguration beyond the bootloader given
the design of the hardware involved which can result in substantial
glitches which may impair functionality of certain peripherals.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

On DRA72 EVM, cpsw slave1 is muxed with VIN2A, hence switch to cpsw
slave0 for ethernet. Add gpio hog entry to pcf_gpio_21 in order to
select cpsw slave0.
Signed-off-by: NVignesh R <vigneshr@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The interconnects on dm816x are like on omap4, so we should use
l3-noc instead of l3-smx. But as the related SoC specific
l3_target_data is still missing from omap_l3_noc let's just
remove the entry for now.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Reported-by: NMatthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Also, reduce the maximum SPI device speed to the max. supported by the
LCD controller used on the LGPhilips LB035Q02 panel for this board.
Signed-off-by: NAsh Charles <ashcharles@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Some Overo COM models include NAND flash in the on-board
package-on-package (PoP) chip.  Add this to the base Overo devicetree.

Most commonly, this is 512MB NAND from the Micron MT29C4G96MAZ family
but, as discussed [1], several different sized are possible. To
support different sizes, the last partition should fill to the end of
the chip (i.e. MTDPART_SIZ_FULL).

With thanks to Florian Vaussard for the original patch [2] and Adam Lee for
updating it here.

[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2013-June/175760.html
[2] http://lists.infradead.org/pipermail/linux-arm-kernel/2013-June/175449.htmlSigned-off-by: NAsh Charles <ashcharles@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Both Gumstix Overo and Overo Storm COMs use TWL4030 audio module
connected to the McBSP2.  As such, enable the McBSP2 module in the
common device tree file, omap3-overo-base.dtsi, rather than in the
processor-specific device tree files, omap3-overo.dtsi and
omap3-overo-storm.dtsi.  This corrects audio on the Storm COMs where
the setting was accidentally missing from the device tree.
Signed-off-by: NAsh Charles <ashcharles@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The Gumstix "Tobi-Duo" expansion board [1] can be used with either
OMAP3 Overo or Overo Storm COMs.  It provides two NICs using LAN9221
chips.
It is necessary to duplicate the interface information for the
second SMSC9221 chip as discussed [2].

[1] https://store.gumstix.com/index.php/products/241/
[2] http://www.spinics.net/lists/linux-omap/msg115282.htmlSigned-off-by: NAsh Charles <ashcharles@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use new binding for the external tda19988 HDMI encoder.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The sDMA requests are routed through the DMA crossbar and without the
crossbar only peripherals using DMA request 0-127 can be used.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add the Wakeup M3 remote processor device node for
the AM4372 SoC. The WkupM3 remote processor is used
to implement and achieve low-power functionality on
the AM33xx & AM43xx SoCs.

This node is added as a child of the recently added
l4_wkup node to reflect its presence within the SoC.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The WakeupM3 remote processor device node has been moved to
be a child node of the newly created l4_wkup node, to reflect
its presence properly within the SoC. The node was added
previously before any driver support, it is now updated as
per the wkup_m3_rproc bindings added alongside the driver
support.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use pdata-quirks to provide platform data required for reset
management during boot and shutdown of the wkup_m3 processor
on both the AM33xx and AM43xx SoCs. The WkupM3 remote processor
is used to implement and achieve low-power functionality on
the AM33xx & AM43xx SoCs.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This reverts commit dec4f799.

Jörg Otte reports a NULL pointder dereference due to this commit, as
'crtc_state' very much can be NULL:

        crtc_state = state->base.state ?
                intel_atomic_get_crtc_state(state->base.state, intel_crtc) : NULL;

So the change to test 'crtc_state->base.active' cannot possibly be
correct as-is.

There may be some other minimal fix (like just checking crtc_state for
NULL), but I'm just reverting it now for the rc2 release, and people
like Daniel Vetter who actually know this code will figure out what the
right solution is in the longer term.
Reported-and-bisected-by: NJörg Otte <jrg.otte@gmail.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
CC: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull VFS fixes from Al Viro:
 "Fixes for this cycle regression in overlayfs and a couple of
  long-standing (== all the way back to 2.6.12, at least) bugs"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  freeing unlinked file indefinitely delayed
  fix a braino in ovl_d_select_inode()
  9p: don't leave a half-initialized inode sitting around

Pull MIPS fixes from Ralf Baechle:
 "A fair number of 4.2 fixes also because Markos opened the flood gates.

   - Patch up the math used calculate the location for the page bitmap.

   - The FDC (Not what you think, FDC stands for Fast Debug Channel) IRQ
     around was causing issues on non-Malta platforms, so move the code
     to a Malta specific location.

   - A spelling fix replicated through several files.

   - Fix to the emulation of an R2 instruction for R6 cores.

   - Fix the JR emulation for R6.

   - Further patching of mindless 64 bit issues.

   - Ensure the kernel won't crash on CPUs with L2 caches with >= 8
     ways.

   - Use compat_sys_getsockopt for O32 ABI on 64 bit kernels.

   - Fix cache flushing for multithreaded cores.

   - A build fix"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: O32: Use compat_sys_getsockopt.
  MIPS: c-r4k: Extend way_string array
  MIPS: Pistachio: Support CDMM & Fast Debug Channel
  MIPS: Malta: Make GIC FDC IRQ workaround Malta specific
  MIPS: c-r4k: Fix cache flushing for MT cores
  Revert "MIPS: Kconfig: Disable SMP/CPS for 64-bit"
  MIPS: cps-vec: Use macros for various arithmetics and memory operations
  MIPS: kernel: cps-vec: Replace KSEG0 with CKSEG0
  MIPS: kernel: cps-vec: Use ta0-ta3 pseudo-registers for 64-bit
  MIPS: kernel: cps-vec: Replace mips32r2 ISA level with mips64r2
  MIPS: kernel: cps-vec: Replace 'la' macro with PTR_LA
  MIPS: kernel: smp-cps: Fix 64-bit compatibility errors due to pointer casting
  MIPS: Fix erroneous JR emulation for MIPS R6
  MIPS: Fix branch emulation for BLTC and BGEC instructions
  MIPS: kernel: traps: Fix broken indentation
  MIPS: bootmem: Don't use memory holes for page bitmap
  MIPS: O32: Do not handle require 32 bytes from the stack to be readable.
  MIPS, CPUFREQ: Fix spelling of Institute.
  MIPS: Lemote 2F: Fix build caused by recent mass rename.

Pull x86 fixes from Thomas Gleixner:

 - the high latency PIT detection fix, which slipped through the cracks
   for rc1

 - a regression fix for the early printk mechanism

 - the x86 part to plug irq/vector related hotplug races

 - move the allocation of the espfix pages on cpu hotplug to non atomic
   context.  The current code triggers a might_sleep() warning.

 - a series of KASAN fixes addressing boot crashes and usability

 - a trivial typo fix for Kconfig help text

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/kconfig: Fix typo in the CONFIG_CMDLINE_BOOL help text
  x86/irq: Retrieve irq data after locking irq_desc
  x86/irq: Use proper locking in check_irq_vectors_for_cpu_disable()
  x86/irq: Plug irq vector hotplug race
  x86/earlyprintk: Allow early_printk() to use console style parameters like '115200n8'
  x86/espfix: Init espfix on the boot CPU side
  x86/espfix: Add 'cpu' parameter to init_espfix_ap()
  x86/kasan: Move KASAN_SHADOW_OFFSET to the arch Kconfig
  x86/kasan: Add message about KASAN being initialized
  x86/kasan: Fix boot crash on AMD processors
  x86/kasan: Flush TLBs after switching CR3
  x86/kasan: Fix KASAN shadow region page tables
  x86/init: Clear 'init_level4_pgt' earlier
  x86/tsc: Let high latency PIT fail fast in quick_pit_calibrate()

Pull timer fixes from Thomas Gleixner:
 "This update from the timer departement contains:

   - A series of patches which address a shortcoming in the tick
     broadcast code.

     If the broadcast device is not available or an hrtimer emulated
     broadcast device, some of the original assumptions lead to boot
     failures.  I rather plugged all of the corner cases instead of only
     addressing the issue reported, so the change got a little larger.

     Has been extensivly tested on x86 and arm.

   - Get rid of the last holdouts using do_posix_clock_monotonic_gettime()

   - A regression fix for the imx clocksource driver

   - An update to the new state callbacks mechanism for clockevents.
     This is required to simplify the conversion, which will take place
     in 4.3"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick/broadcast: Prevent NULL pointer dereference
  time: Get rid of do_posix_clock_monotonic_gettime
  cris: Replace do_posix_clock_monotonic_gettime()
  tick/broadcast: Unbreak CONFIG_GENERIC_CLOCKEVENTS=n build
  tick/broadcast: Handle spurious interrupts gracefully
  tick/broadcast: Check for hrtimer broadcast active early
  tick/broadcast: Return busy when IPI is pending
  tick/broadcast: Return busy if periodic mode and hrtimer broadcast
  tick/broadcast: Move the check for periodic mode inside state handling
  tick/broadcast: Prevent deep idle if no broadcast device available
  tick/broadcast: Make idle check independent from mode and config
  tick/broadcast: Sanity check the shutdown of the local clock_event
  tick/broadcast: Prevent hrtimer recursion
  clockevents: Allow set-state callbacks to be optional
  clocksource/imx: Define clocksource for mx27

Pull irq fix from Thomas Gleixner:
 "A single fix for a cpu hotplug race vs. interrupt descriptors:

  Prevent irq setup/teardown across the cpu starting/dying parts of cpu
  hotplug so that the starting/dying cpu has a stable view of the
  descriptor space.  This has been an issue for all architectures in the
  cpu dying phase, where interrupts are migrated away from the dying
  cpu.  In the starting phase its mostly a x86 issue vs the vector space
  update"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  hotplug: Prevent alloc/free of irq descriptors during cpu up/down

	Normally opening a file, unlinking it and then closing will have
the inode freed upon close() (provided that it's not otherwise busy and
has no remaining links, of course).  However, there's one case where that
does *not* happen.  Namely, if you open it by fhandle with cold dcache,
then unlink() and close().

	In normal case you get d_delete() in unlink(2) notice that dentry
is busy and unhash it; on the final dput() it will be forcibly evicted from
dcache, triggering iput() and inode removal.  In this case, though, we end
up with *two* dentries - disconnected (created by open-by-fhandle) and
regular one (used by unlink()).  The latter will have its reference to inode
dropped just fine, but the former will not - it's considered hashed (it
is on the ->s_anon list), so it will stay around until the memory pressure
will finally do it in.  As the result, we have the final iput() delayed
indefinitely.  It's trivial to reproduce -

void flush_dcache(void)
{
        system("mount -o remount,rw /");
}

static char buf[20 * 1024 * 1024];

main()
{
        int fd;
        union {
                struct file_handle f;
                char buf[MAX_HANDLE_SZ];
        } x;
        int m;

        x.f.handle_bytes = sizeof(x);
        chdir("/root");
        mkdir("foo", 0700);
        fd = open("foo/bar", O_CREAT | O_RDWR, 0600);
        close(fd);
        name_to_handle_at(AT_FDCWD, "foo/bar", &x.f, &m, 0);
        flush_dcache();
        fd = open_by_handle_at(AT_FDCWD, &x.f, O_RDWR);
        unlink("foo/bar");
        write(fd, buf, sizeof(buf));
        system("df .");			/* 20Mb eaten */
        close(fd);
        system("df .");			/* should've freed those 20Mb */
        flush_dcache();
        system("df .");			/* should be the same as #2 */
}

will spit out something like
Filesystem     1K-blocks   Used Available Use% Mounted on
/dev/root         322023 303843      1131 100% /
Filesystem     1K-blocks   Used Available Use% Mounted on
/dev/root         322023 303843      1131 100% /
Filesystem     1K-blocks   Used Available Use% Mounted on
/dev/root         322023 283282     21692  93% /
- inode gets freed only when dentry is finally evicted (here we trigger
than by remount; normally it would've happened in response to memory
pressure hell knows when).

Cc: stable@vger.kernel.org # v2.6.38+; earlier ones need s/kill_it/unhash_it/
Acked-by: NJ. Bruce Fields <bfields@fieldses.org>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

when opening a directory we want the overlayfs inode, not one from
the topmost layer.
Reported-By: NAndrey Jr. Melnikov <temnota.am@gmail.com>
Tested-By: NAndrey Jr. Melnikov <temnota.am@gmail.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Cc: stable@vger.kernel.org # all branches
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Pull libnvdimm fixes from Dan Williams:
 "1) Fixes for a handful of smatch reports (Thanks Dan C.!) and minor
     bug fixes (patches 1-6)

  2) Correctness fixes to the BLK-mode nvdimm driver (patches 7-10).

     Granted these are slightly large for a -rc update.  They have been
     out for review in one form or another since the end of May and were
     deferred from the merge window while we settled on the "PMEM API"
     for the PMEM-mode nvdimm driver (ie memremap_pmem, memcpy_to_pmem,
     and wmb_pmem).

     Now that those apis are merged we implement them in the BLK driver
     to guarantee that mmio aperture moves stay ordered with respect to
     incoming read/write requests, and that writes are flushed through
     those mmio-windows and platform-buffers to be persistent on media.

  These pass the sub-system unit tests with the updates to
  tools/testing/nvdimm, and have received a successful build-report from
  the kbuild robot (468 configs).

  With acks from Rafael for the touches to drivers/acpi/"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm:
  nfit: add support for NVDIMM "latch" flag
  nfit: update block I/O path to use PMEM API
  tools/testing/nvdimm: add mock acpi_nfit_flush_address entries to nfit_test
  tools/testing/nvdimm: fix return code for unimplemented commands
  tools/testing/nvdimm: mock ioremap_wt
  pmem: add maintainer for include/linux/pmem.h
  nfit: fix smatch "use after null check" report
  nvdimm: Fix return value of nvdimm_bus_init() if class_create() fails
  libnvdimm: smatch cleanups in __nd_ioctl
  sparse: fix misplaced __pmem definition

Pull i2c fixes from Wolfram Sang:
 "Mostly slight adjusments for new drivers, but also one core fix for
  which finally the dependencies are now available as well"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: Mark instantiated device nodes with OF_POPULATE
  i2c: jz4780: Fix return value if probe fails
  i2c: xgene-slimpro: Fix missing mbox_free_channel call in probe error path
  i2c: I2C_MT65XX should depend on HAS_DMA

Pull input fixes from Dmitry Torokhov:
 "A fix (revert) for a recent regression in Synaptics driver and a fix
  for Elan i2c touchpad driver"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Revert "Input: synaptics - allocate 3 slots to keep stability in image sensors"
  Input: elan_i2c - change the hover event from MT to ST

Pull clk fixes from Stephen Boyd:
 "A small set of fixes for problems found by smatch in new drivers that
  we added this rc and a handful of driver fixes that came in during the
  merge window"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  drivers: clk: st: Incorrect register offset used for lock_status
  clk: mediatek: mt8173: Fix enabling of critical clocks
  drivers: clk: st: Fix mux bit-setting for Cortex A9 clocks
  drivers: clk: st: Add CLK_GET_RATE_NOCACHE flag to clocks
  drivers: clk: st: Fix flexgen lock init
  drivers: clk: st: Fix FSYN channel values
  drivers: clk: st: Remove unused code
  clk: qcom: Use parent rate when set rate to pixel RCG clock
  clk: at91: do not leak resources
  clk: stm32: Fix out-by-one error path in the index lookup
  clk: iproc: fix bit manipulation arithmetic
  clk: iproc: fix memory leak from clock name

Pull drm fixes from Dave Airlie:
 "A bunch of fixes for radeon, intel, omap and one amdkfd fix.

  Radeon fixes are all over, but it does fix some cursor corruption
  across suspend/resume.  i915 should fix the second warn you were
  seeing, so let us know if not.  omap is a bunch of small fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (28 commits)
  drm/radeon: disable vce init on cayman (v2)
  drm/amdgpu: fix timeout calculation
  drm/radeon: check if BO_VA is set before adding it to the invalidation list
  drm/radeon: allways add the VM clear duplicate
  Revert "Revert "drm/radeon: dont switch vt on suspend""
  drm/radeon: Fold radeon_set_cursor() into radeon_show_cursor()
  drm/radeon: unpin cursor BOs on suspend and pin them again on resume (v2)
  drm/radeon: Clean up reference counting and pinning of the cursor BOs
  drm/amdkfd: validate pdd where it acquired first
  Revert "drm/i915: Allocate context objects from stolen"
  drm/i915: Declare the swizzling unknown for L-shaped configurations
  drm/radeon: fix underflow in r600_cp_dispatch_texture()
  drm/radeon: default to 2048 MB GART size on SI+
  drm/radeon: fix HDP flushing
  drm/radeon: use RCU query for GEM_BUSY syscall
  drm/amdgpu: Handle irqs only based on irq ring, not irq status regs.
  drm/radeon: Handle irqs only based on irq ring, not irq status regs.
  drm/i915: Use crtc_state->active in primary check_plane func
  drm/i915: Check crtc->active in intel_crtc_disable_planes
  drm/i915: Restore all GGTT VMAs on resume
  ...

Pull selinux fixes from James Morris.

* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  selinux: fix mprotect PROT_EXEC regression caused by mm change
  selinux: don't waste ebitmap space when importing NetLabel categories

Pull btrfs fixes from Chris Mason:
 "This is an assortment of fixes.  Most of the commits are from Filipe
  (fsync, the inode allocation cache and a few others).  Mark kicked in
  a series fixing corners in the extent sharing ioctls, and everyone
  else fixed up on assorted other problems"

* 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix wrong check for btrfs_force_chunk_alloc()
  Btrfs: fix warning of bytes_may_use
  Btrfs: fix hang when failing to submit bio of directIO
  Btrfs: fix a comment in inode.c:evict_inode_truncate_pages()
  Btrfs: fix memory corruption on failure to submit bio for direct IO
  btrfs: don't update mtime/ctime on deduped inodes
  btrfs: allow dedupe of same inode
  btrfs: fix deadlock with extent-same and readpage
  btrfs: pass unaligned length to btrfs_cmp_data()
  Btrfs: fix fsync after truncate when no_holes feature is enabled
  Btrfs: fix fsync xattr loss in the fast fsync path
  Btrfs: fix fsync data loss after append write
  Btrfs: fix crash on close_ctree() if cleaner starts new transaction
  Btrfs: fix race between caching kthread and returning inode to inode cache
  Btrfs: use kmem_cache_free when freeing entry in inode cache
  Btrfs: fix race between balance and unused block group deletion
  btrfs: add error handling for scrub_workers_get()
  btrfs: cleanup noused initialization of dev in btrfs_end_bio()
  btrfs: qgroup: allow user to clear the limitation on qgroup

Pull ARM SoC fixes from Kevin Hilman:
 "A fairly random colletion of fixes based on -rc1 for OMAP, sunxi and
  prima2 as well as a few arm64-specific DT fixes.

  This series also includes a late to support a new Allwinner (sunxi)
  SoC, but since it's rather simple and isolated to the
  platform-specific code, it's included it for this -rc"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: dts: add device tree for ARM SMM-A53x2 on LogicTile Express 20MG
  arm: dts: vexpress: add missing CCI PMU device node to TC2
  arm: dts: vexpress: describe all PMUs in TC2 dts
  GICv3: Add ITS entry to THUNDER dts
  arm64: dts: Add poweroff button device node for APM X-Gene platform
  ARM: dts: am4372.dtsi: disable rfbi
  ARM: dts: am57xx-beagle-x15: Provide supply for usb2_phy2
  ARM: dts: am4372: Add emif node
  Revert "ARM: dts: am335x-boneblack: disable RTC-only sleep"
  ARM: sunxi: Enable simplefb in the defconfig
  ARM: Remove deprecated symbol from defconfig files
  ARM: sunxi: Add Machine support for A33
  ARM: sunxi: Introduce Allwinner H3 support
  Documentation: sunxi: Update Allwinner SoC documentation
  ARM: prima2: move to use REGMAP APIs for rtciobrg
  ARM: dts: atlas7: add pinctrl and gpio descriptions
  ARM: OMAP2+: Remove unnessary return statement from the void function, omap2_show_dma_caps
  memory: omap-gpmc: Fix parsing of devices