The firmware sends a IF event to notify the host driver that the
P2P_DEVICE interface has been created. Wait for the event before
returning the related wireless_dev.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current driver code creates a P2P_DEVICE through a module
parameter. This device has a dummy netdevice which is not how this
interface type is intended. This patch add proper support for the
P2P_DEVICE interface type. This requires a wpa_supplicant with such
support as well.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

escan functionality is also required for P2P device operations so it
is better not to rely on struct netdevice instances.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove use of struct netdevice as parameter to brcmf_set_mpc() as it
will not always be available, ie. there will be non-netdevice interfaces.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the introduction of the P2P_DEVICE interface type an instance of
struct wireless_dev does not always have a netdev assigned to it. Better
use container_of() construct to obtain internal structure and go from
there.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In fweh module the event handler was only called if the
struct brcmf_if instance had a non-null netdev associated.
This restriction is no longer valid for P2P_DEVICE type
of interface. This patch removes that restriction.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According specification the IF event has an additional field indicating
the role or type of the interface for which this event is sent.
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adds a trace function used in brcmf_dbg_hex_dump() which adds the
raw binary data to the trace. It requires trace-cmd plugin to see
this data.
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firware shared data structure is backward compatible for fields
we are interested in.
Allow reading of shared data in case of version mismatch.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware console output can be read also when there was
no trap indication.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The firmware can request the host driver for packets, by sending
either the MAC_REQUEST_CREDIT or the MAC_REQUEST_PACKET primitive.
This patch adds handling of these primitives.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware can signal whether the host driver may sent packets for
a specific destination or interface. This can happen when a
destination is sleeping or when going off-channel.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

reported by Hante. Needs to be squashed in commit 187fbcec.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware provides the driver with credits used to transmit packets
to the firmware. When credits run out the packets should be queued
and dequeued when receiving creditback signals from the firmware.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The fcmode provided by module parameter defaults to NONE, which
means no flow-control is required. In this case flow-control
signals should not be enabled.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Bail out of brcmf_fws_init() when no firmware-signalling is asked
for. Need to take this into account in brcmf_fws_deinit() as well.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The functions are moved in preparation of later patches.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The length is not according specification so better fix it.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If iovar to the firmware fails the firmware-signalling module
does a cleanup for which it needs pointer to struct brcmf_pub, which
it gets from struct brcmf_fws_info::drvr. Assign this field before
doing the tlv iovar.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The low-level sdio code has a large number of trace and info messages
that are mostly useful looking into bus specific issues. For tracing
higher-level driver functions it is better to have a dedicated level
for low-level sdio debugging.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Change-Id: Ia424ff18d9033b97aeffc248358e50c51805e815
Reviewed-on: http://lb-bun-88.bun.broadcom.com:8080/74Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During SDIO layer flow control signalling firmware can issue
invalid packets. Prevent printing of parsing errors in such case.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Parsing the tlv upon receiving frames can fail. Instead of printing
an error message, just count the parse failure. On some devices we
receive a lot of invalid tlv signals.

this commit will be squashed.
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Change-Id: I08e0f62c55e5028f9aa70c396d291679abd273c9
Reviewed-on: http://lb-bun-88.bun.broadcom.com:8080/72Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When firmware-signalling is active the brcmf_txcomplete() does
a free of the sk_buff when transfer to firmware fails in the
bus-specific driver code. However, it should also cleanup the
packet from the hanger. This patch fixes that.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enabling the tx status signalling, which requires packet tagging
before sending to the firmware and handling the tx status signal.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Upcoming patches will add firmware signalled flow control. Prepare
by adding the mode, which defaults to disable it. The mode can be
queried by brcmf_fws_fc_active() and set by a module parameter.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a callback to obtain packet queue from the bus-specific code
used to cleanup packet buffers from firmware-signalling code.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The hanger for firmware-signalling is used to retain information for
outstanding transmit packets that await tx status.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When an interface is deleted make sure to cleanup all packet
buffers related to that interface.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The sk_buff structure contains a control buffer that can be used
by different layers in the networking stack for holding packet
associated information. In brcmfmac it is used to hold firmware
signalling related information.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, the netif queue is only stopped when the bus interface is
giving a push back. This will change soon so prepare the driver by
adding a stop reason and stop/resume the queue accordingly.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a cleanup function releasing any queued packet buffers in
the mac descriptor entries.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The firmware signalling functionality needs the credit map firmware
events. This patch adds registration of a handler for this event.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware can signal the driver to allocate descriptor info for a given
mac address, which will be used for flow control and host queueing.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware signalling needs to handle resources upon interface
events. This patch add calls in the interface event handling
routine.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use information from the device to determine the bands property
of the wiphy object. After this change the support of 80211n is
correctly presented in the bands property.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In brcmf_sdbrcm_txpkt() a new packet is allocated and used to transmit
to firmware freeing up the original packet. However, that packet is
still referenced in firmware-signalling so this would result in a
double free. Using skb_cow() avoids this as the packet reference is
unchanged.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When taking care of packet alignment to 64-byte boundary padding may
be added between SDPCM header and CDC data. It clear both SDPCM header
space and padding space. Changed it to only clear padding space. In
filling the SDPCM header it uses unaligned access to set SDPCM software
header, but preceding code assures it is properly aligned.
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Change-Id: Iad22f277f3496440ba4d2db771205714774570ac
Reviewed-on: http://lb-bun-88.bun.broadcom.com:8080/76Reviewed-by: NFranky Lin <frankyl@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function brcmf_sdbrcm_txpkt() calls brcmf_txcomplete() with
a parameter success. For this parameter it passes ret != 0, but
that condition is true upon failure.
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This removes the following functions:
si_pmu_chipcontrol() => bcma_chipco_chipctl_maskset()
si_pmu_regcontrol() => bcma_chipco_regctl_maskset()
si_pmu_pllcontrol() => bcma_chipco_pll_maskset()
si_pmu_pllupd() => bcma_cc_set32()
si_pmu_alp_clock() => bcma_chipco_get_alp_clock()

This also removed the sih member from struct shared_phy.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds adhoc mode support to brcmsmac.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>