alpha: Allow HZ to be configured

With the 1024Hz default, we spend 50% of QEMU emulation
processing timer interrupts.
Signed-off-by: NRichard Henderson <rth@twiddle.net>

arch/alpha/Kconfig

@@ -627,9 +627,41 @@ config VERBOSE_MCHECK_ON
 
 	  Take the default (1) unless you want more control or more info.
 
+choice
+	prompt "Timer interrupt frequency (HZ)?"
+	default HZ_128 if ALPHA_QEMU
+	default HZ_1200 if ALPHA_RAWHIDE
+	default HZ_1024
+	---help---
+	  The frequency at which timer interrupts occur.  A high frequency
+	  minimizes latency, whereas a low frequency minimizes overhead of
+	  process accounting.  The later effect is especially significant
+	  when being run under QEMU.
+
+	  Note that some Alpha hardware cannot change the interrupt frequency
+	  of the timer.  If unsure, say 1024 (or 1200 for Rawhide).
+
+	config HZ_32
+		bool "32 Hz"
+	config HZ_64
+		bool "64 Hz"
+	config HZ_128
+		bool "128 Hz"
+	config HZ_256
+		bool "256 Hz"
+	config HZ_1024
+		bool "1024 Hz"
+	config HZ_1200
+		bool "1200 Hz"
+endchoice
+
 config HZ
 	int 
-	default 1200 if ALPHA_RAWHIDE
+	default 32 if HZ_32
+	default 64 if HZ_64
+	default 128 if HZ_128
+	default 256 if HZ_256
+	default 1200 if HZ_1200
 	default 1024
 
 source "drivers/pci/Kconfig"

arch/alpha/kernel/setup.c

@@ -1218,6 +1218,7 @@ show_cpuinfo(struct seq_file *f, void *slot)
 	char *systype_name;
 	char *sysvariation_name;
 	int nr_processors;
+	unsigned long timer_freq;
 
 	cpu_index = (unsigned) (cpu->type - 1);
 	cpu_name = "Unknown";
@@ -1229,6 +1230,12 @@ show_cpuinfo(struct seq_file *f, void *slot)
 
 	nr_processors = get_nr_processors(cpu, hwrpb->nr_processors);
 
+#if CONFIG_HZ == 1024 || CONFIG_HZ == 1200
+	timer_freq = (100UL * hwrpb->intr_freq) / 4096;
+#else
+	timer_freq = 100UL * CONFIG_HZ;
+#endif
+
 	seq_printf(f, "cpu\t\t\t: Alpha\n"
 		      "cpu model\t\t: %s\n"
 		      "cpu variation\t\t: %ld\n"
@@ -1254,8 +1261,7 @@ show_cpuinfo(struct seq_file *f, void *slot)
 		       (char*)hwrpb->ssn,
 		       est_cycle_freq ? : hwrpb->cycle_freq,
 		       est_cycle_freq ? "est." : "",
-		       hwrpb->intr_freq / 4096,
-		       (100 * hwrpb->intr_freq / 4096) % 100,
+		       timer_freq / 100, timer_freq % 100,
 		       hwrpb->pagesize,
 		       hwrpb->pa_bits,
 		       hwrpb->max_asn,

arch/alpha/kernel/time.c

@@ -201,15 +201,25 @@ irqreturn_t timer_interrupt(int irq, void *dev)
 void __init
 common_init_rtc(void)
 {
-	unsigned char x;
+	unsigned char x, sel = 0;
 
 	/* Reset periodic interrupt frequency.  */
+#if CONFIG_HZ == 1024 || CONFIG_HZ == 1200
  	x = CMOS_READ(RTC_FREQ_SELECT) & 0x3f;
 	/* Test includes known working values on various platforms
 	   where 0x26 is wrong; we refuse to change those. */
  	if (x != 0x26 && x != 0x25 && x != 0x19 && x != 0x06) {
-		printk("Setting RTC_FREQ to 1024 Hz (%x)\n", x);
-		CMOS_WRITE(0x26, RTC_FREQ_SELECT);
+		sel = RTC_REF_CLCK_32KHZ + 6;
+	}
+#elif CONFIG_HZ == 256 || CONFIG_HZ == 128 || CONFIG_HZ == 64 || CONFIG_HZ == 32
+	sel = RTC_REF_CLCK_32KHZ + __builtin_ffs(32768 / CONFIG_HZ);
+#else
+# error "Unknown HZ from arch/alpha/Kconfig"
+#endif
+	if (sel) {
+		printk(KERN_INFO "Setting RTC_FREQ to %d Hz (%x)\n",
+		       CONFIG_HZ, sel);
+		CMOS_WRITE(sel, RTC_FREQ_SELECT);
  	}
 
 	/* Turn on periodic interrupts.  */