diff --git a/Documentation/devicetree/bindings/spi/brcm,bcm2835-spi.txt b/Documentation/devicetree/bindings/spi/brcm,bcm2835-spi.txt
new file mode 100644
index 0000000000000000000000000000000000000000..8bf89c643640871271ebaab313bc4edca1cbc165
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/brcm,bcm2835-spi.txt
@@ -0,0 +1,22 @@
+Broadcom BCM2835 SPI0 controller
+
+The BCM2835 contains two forms of SPI master controller, one known simply as
+SPI0, and the other known as the "Universal SPI Master"; part of the
+auxilliary block. This binding applies to the SPI0 controller.
+
+Required properties:
+- compatible: Should be "brcm,bcm2835-spi".
+- reg: Should contain register location and length.
+- interrupts: Should contain interrupt.
+- clocks: The clock feeding the SPI controller.
+
+Example:
+
+spi@20204000 {
+	compatible = "brcm,bcm2835-spi";
+	reg = <0x7e204000 0x1000>;
+	interrupts = <2 22>;
+	clocks = <&clk_spi>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+};
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index f80eee74a3116c5a8935378d908fce904e3351f6..32b85d43bbe2a594ac9b939345fb5d54fc0b2dcb 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -74,6 +74,17 @@ config SPI_ATMEL
 	  This selects a driver for the Atmel SPI Controller, present on
 	  many AT32 (AVR32) and AT91 (ARM) chips.
 
+config SPI_BCM2835
+	tristate "BCM2835 SPI controller"
+	depends on ARCH_BCM2835
+	help
+	  This selects a driver for the Broadcom BCM2835 SPI master.
+
+	  The BCM2835 contains two types of SPI master controller; the
+	  "universal SPI master", and the regular SPI controller. This driver
+	  is for the regular SPI controller. Slave mode operation is not also
+	  not supported.
+
 config SPI_BFIN5XX
 	tristate "SPI controller driver for ADI Blackfin5xx"
 	depends on BLACKFIN
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index e53c3094134040b7e6d396df45056cdc77f51201..3ce1d082ce79b870a0201a5521ecaeaf3d33d01a 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -14,6 +14,7 @@ obj-$(CONFIG_SPI_ALTERA)		+= spi-altera.o
 obj-$(CONFIG_SPI_ATMEL)			+= spi-atmel.o
 obj-$(CONFIG_SPI_ATH79)			+= spi-ath79.o
 obj-$(CONFIG_SPI_AU1550)		+= spi-au1550.o
+obj-$(CONFIG_SPI_BCM2835)		+= spi-bcm2835.o
 obj-$(CONFIG_SPI_BCM63XX)		+= spi-bcm63xx.o
 obj-$(CONFIG_SPI_BFIN5XX)		+= spi-bfin5xx.o
 obj-$(CONFIG_SPI_BFIN_SPORT)		+= spi-bfin-sport.o
diff --git a/drivers/spi/spi-bcm2835.c b/drivers/spi/spi-bcm2835.c
new file mode 100644
index 0000000000000000000000000000000000000000..346601e2461d78abd8dac6d26e708c86345f1326
--- /dev/null
+++ b/drivers/spi/spi-bcm2835.c
@@ -0,0 +1,456 @@
+/*
+ * Driver for Broadcom BCM2835 SPI Controllers
+ *
+ * Copyright (C) 2012 Chris Boot
+ * Copyright (C) 2013 Stephen Warren
+ *
+ * This driver is inspired by:
+ * spi-ath79.c, Copyright (C) 2009-2011 Gabor Juhos <juhosg@openwrt.org>
+ * spi-atmel.c, Copyright (C) 2006 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_device.h>
+#include <linux/spi/spi.h>
+
+/* SPI register offsets */
+#define BCM2835_SPI_CS			0x00
+#define BCM2835_SPI_FIFO		0x04
+#define BCM2835_SPI_CLK			0x08
+#define BCM2835_SPI_DLEN		0x0c
+#define BCM2835_SPI_LTOH		0x10
+#define BCM2835_SPI_DC			0x14
+
+/* Bitfields in CS */
+#define BCM2835_SPI_CS_LEN_LONG		0x02000000
+#define BCM2835_SPI_CS_DMA_LEN		0x01000000
+#define BCM2835_SPI_CS_CSPOL2		0x00800000
+#define BCM2835_SPI_CS_CSPOL1		0x00400000
+#define BCM2835_SPI_CS_CSPOL0		0x00200000
+#define BCM2835_SPI_CS_RXF		0x00100000
+#define BCM2835_SPI_CS_RXR		0x00080000
+#define BCM2835_SPI_CS_TXD		0x00040000
+#define BCM2835_SPI_CS_RXD		0x00020000
+#define BCM2835_SPI_CS_DONE		0x00010000
+#define BCM2835_SPI_CS_LEN		0x00002000
+#define BCM2835_SPI_CS_REN		0x00001000
+#define BCM2835_SPI_CS_ADCS		0x00000800
+#define BCM2835_SPI_CS_INTR		0x00000400
+#define BCM2835_SPI_CS_INTD		0x00000200
+#define BCM2835_SPI_CS_DMAEN		0x00000100
+#define BCM2835_SPI_CS_TA		0x00000080
+#define BCM2835_SPI_CS_CSPOL		0x00000040
+#define BCM2835_SPI_CS_CLEAR_RX		0x00000020
+#define BCM2835_SPI_CS_CLEAR_TX		0x00000010
+#define BCM2835_SPI_CS_CPOL		0x00000008
+#define BCM2835_SPI_CS_CPHA		0x00000004
+#define BCM2835_SPI_CS_CS_10		0x00000002
+#define BCM2835_SPI_CS_CS_01		0x00000001
+
+#define BCM2835_SPI_TIMEOUT_MS	30000
+#define BCM2835_SPI_MODE_BITS	(SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_NO_CS)
+
+#define DRV_NAME	"spi-bcm2835"
+
+struct bcm2835_spi {
+	void __iomem *regs;
+	struct clk *clk;
+	int irq;
+	struct completion done;
+	const u8 *tx_buf;
+	u8 *rx_buf;
+	int len;
+};
+
+static inline u32 bcm2835_rd(struct bcm2835_spi *bs, unsigned reg)
+{
+	return readl(bs->regs + reg);
+}
+
+static inline void bcm2835_wr(struct bcm2835_spi *bs, unsigned reg, u32 val)
+{
+	writel(val, bs->regs + reg);
+}
+
+static inline void bcm2835_rd_fifo(struct bcm2835_spi *bs, int len)
+{
+	u8 byte;
+
+	while (len--) {
+		byte = bcm2835_rd(bs, BCM2835_SPI_FIFO);
+		if (bs->rx_buf)
+			*bs->rx_buf++ = byte;
+	}
+}
+
+static inline void bcm2835_wr_fifo(struct bcm2835_spi *bs, int len)
+{
+	u8 byte;
+
+	if (len > bs->len)
+		len = bs->len;
+
+	while (len--) {
+		byte = bs->tx_buf ? *bs->tx_buf++ : 0;
+		bcm2835_wr(bs, BCM2835_SPI_FIFO, byte);
+		bs->len--;
+	}
+}
+
+static irqreturn_t bcm2835_spi_interrupt(int irq, void *dev_id)
+{
+	struct spi_master *master = dev_id;
+	struct bcm2835_spi *bs = spi_master_get_devdata(master);
+	u32 cs = bcm2835_rd(bs, BCM2835_SPI_CS);
+
+	/*
+	 * RXR - RX needs Reading. This means 12 (or more) bytes have been
+	 * transmitted and hence 12 (or more) bytes have been received.
+	 *
+	 * The FIFO is 16-bytes deep. We check for this interrupt to keep the
+	 * FIFO full; we have a 4-byte-time buffer for IRQ latency. We check
+	 * this before DONE (TX empty) just in case we delayed processing this
+	 * interrupt for some reason.
+	 *
+	 * We only check for this case if we have more bytes to TX; at the end
+	 * of the transfer, we ignore this pipelining optimization, and let
+	 * bcm2835_spi_finish_transfer() drain the RX FIFO.
+	 */
+	if (bs->len && (cs & BCM2835_SPI_CS_RXR)) {
+		/* Read 12 bytes of data */
+		bcm2835_rd_fifo(bs, 12);
+
+		/* Write up to 12 bytes */
+		bcm2835_wr_fifo(bs, 12);
+
+		/*
+		 * We must have written something to the TX FIFO due to the
+		 * bs->len check above, so cannot be DONE. Hence, return
+		 * early. Note that DONE could also be set if we serviced an
+		 * RXR interrupt really late.
+		 */
+		return IRQ_HANDLED;
+	}
+
+	/*
+	 * DONE - TX empty. This occurs when we first enable the transfer
+	 * since we do not pre-fill the TX FIFO. At any other time, given that
+	 * we refill the TX FIFO above based on RXR, and hence ignore DONE if
+	 * RXR is set, DONE really does mean end-of-transfer.
+	 */
+	if (cs & BCM2835_SPI_CS_DONE) {
+		if (bs->len) { /* First interrupt in a transfer */
+			bcm2835_wr_fifo(bs, 16);
+		} else { /* Transfer complete */
+			/* Disable SPI interrupts */
+			cs &= ~(BCM2835_SPI_CS_INTR | BCM2835_SPI_CS_INTD);
+			bcm2835_wr(bs, BCM2835_SPI_CS, cs);
+
+			/*
+			 * Wake up bcm2835_spi_transfer_one(), which will call
+			 * bcm2835_spi_finish_transfer(), to drain the RX FIFO.
+			 */
+			complete(&bs->done);
+		}
+
+		return IRQ_HANDLED;
+	}
+
+	return IRQ_NONE;
+}
+
+static int bcm2835_spi_check_transfer(struct spi_device *spi,
+		struct spi_transfer *tfr)
+{
+	/* tfr==NULL when called from bcm2835_spi_setup() */
+	u32 bpw = tfr ? tfr->bits_per_word : spi->bits_per_word;
+
+	switch (bpw) {
+	case 8:
+		break;
+	default:
+		dev_err(&spi->dev, "unsupported bits_per_word=%d\n", bpw);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int bcm2835_spi_start_transfer(struct spi_device *spi,
+		struct spi_transfer *tfr)
+{
+	struct bcm2835_spi *bs = spi_master_get_devdata(spi->master);
+	unsigned long spi_hz, clk_hz, cdiv;
+	u32 cs = BCM2835_SPI_CS_INTR | BCM2835_SPI_CS_INTD | BCM2835_SPI_CS_TA;
+
+	spi_hz = tfr->speed_hz;
+	clk_hz = clk_get_rate(bs->clk);
+
+	if (spi_hz >= clk_hz / 2) {
+		cdiv = 2; /* clk_hz/2 is the fastest we can go */
+	} else if (spi_hz) {
+		/* CDIV must be a power of two */
+		cdiv = roundup_pow_of_two(DIV_ROUND_UP(clk_hz, spi_hz));
+
+		if (cdiv >= 65536)
+			cdiv = 0; /* 0 is the slowest we can go */
+	} else
+		cdiv = 0; /* 0 is the slowest we can go */
+
+	if (spi->mode & SPI_CPOL)
+		cs |= BCM2835_SPI_CS_CPOL;
+	if (spi->mode & SPI_CPHA)
+		cs |= BCM2835_SPI_CS_CPHA;
+
+	if (!(spi->mode & SPI_NO_CS)) {
+		if (spi->mode & SPI_CS_HIGH) {
+			cs |= BCM2835_SPI_CS_CSPOL;
+			cs |= BCM2835_SPI_CS_CSPOL0 << spi->chip_select;
+		}
+
+		cs |= spi->chip_select;
+	}
+
+	INIT_COMPLETION(bs->done);
+	bs->tx_buf = tfr->tx_buf;
+	bs->rx_buf = tfr->rx_buf;
+	bs->len = tfr->len;
+
+	bcm2835_wr(bs, BCM2835_SPI_CLK, cdiv);
+	/*
+	 * Enable the HW block. This will immediately trigger a DONE (TX
+	 * empty) interrupt, upon which we will fill the TX FIFO with the
+	 * first TX bytes. Pre-filling the TX FIFO here to avoid the
+	 * interrupt doesn't work:-(
+	 */
+	bcm2835_wr(bs, BCM2835_SPI_CS, cs);
+
+	return 0;
+}
+
+static int bcm2835_spi_finish_transfer(struct spi_device *spi,
+		struct spi_transfer *tfr, bool cs_change)
+{
+	struct bcm2835_spi *bs = spi_master_get_devdata(spi->master);
+	u32 cs = bcm2835_rd(bs, BCM2835_SPI_CS);
+
+	/* Drain RX FIFO */
+	while (cs & BCM2835_SPI_CS_RXD) {
+		bcm2835_rd_fifo(bs, 1);
+		cs = bcm2835_rd(bs, BCM2835_SPI_CS);
+	}
+
+	if (tfr->delay_usecs)
+		udelay(tfr->delay_usecs);
+
+	if (cs_change)
+		/* Clear TA flag */
+		bcm2835_wr(bs, BCM2835_SPI_CS, cs & ~BCM2835_SPI_CS_TA);
+
+	return 0;
+}
+
+static int bcm2835_spi_setup(struct spi_device *spi)
+{
+	int ret;
+
+	ret = bcm2835_spi_check_transfer(spi, NULL);
+	if (ret) {
+		dev_err(&spi->dev, "setup: invalid message\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int bcm2835_spi_transfer_one(struct spi_master *master,
+		struct spi_message *mesg)
+{
+	struct bcm2835_spi *bs = spi_master_get_devdata(master);
+	struct spi_transfer *tfr;
+	struct spi_device *spi = mesg->spi;
+	int err = 0;
+	unsigned int timeout;
+	bool cs_change;
+
+	list_for_each_entry(tfr, &mesg->transfers, transfer_list) {
+		err = bcm2835_spi_check_transfer(spi, tfr);
+		if (err)
+			goto out;
+
+		err = bcm2835_spi_start_transfer(spi, tfr);
+		if (err)
+			goto out;
+
+		timeout = wait_for_completion_timeout(&bs->done,
+				msecs_to_jiffies(BCM2835_SPI_TIMEOUT_MS));
+		if (!timeout) {
+			err = -ETIMEDOUT;
+			goto out;
+		}
+
+		cs_change = tfr->cs_change ||
+			list_is_last(&tfr->transfer_list, &mesg->transfers);
+
+		err = bcm2835_spi_finish_transfer(spi, tfr, cs_change);
+		if (err)
+			goto out;
+
+		mesg->actual_length += (tfr->len - bs->len);
+	}
+
+out:
+	/* Clear FIFOs, and disable the HW block */
+	bcm2835_wr(bs, BCM2835_SPI_CS,
+		   BCM2835_SPI_CS_CLEAR_RX | BCM2835_SPI_CS_CLEAR_TX);
+	mesg->status = err;
+	spi_finalize_current_message(master);
+
+	return 0;
+}
+
+static int bcm2835_spi_probe(struct platform_device *pdev)
+{
+	struct spi_master *master;
+	struct bcm2835_spi *bs;
+	struct resource *res;
+	int err;
+
+	master = spi_alloc_master(&pdev->dev, sizeof(*bs));
+	if (!master) {
+		dev_err(&pdev->dev, "spi_alloc_master() failed\n");
+		return -ENOMEM;
+	}
+
+	platform_set_drvdata(pdev, master);
+
+	master->mode_bits = BCM2835_SPI_MODE_BITS;
+	master->bus_num = -1;
+	master->num_chipselect = 3;
+	master->setup = bcm2835_spi_setup;
+	master->transfer_one_message = bcm2835_spi_transfer_one;
+	master->dev.of_node = pdev->dev.of_node;
+
+	bs = spi_master_get_devdata(master);
+
+	init_completion(&bs->done);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "could not get memory resource\n");
+		err = -ENODEV;
+		goto out_master_put;
+	}
+
+	bs->regs = devm_request_and_ioremap(&pdev->dev, res);
+	if (!bs->regs) {
+		dev_err(&pdev->dev, "could not request/map memory region\n");
+		err = -ENODEV;
+		goto out_master_put;
+	}
+
+	bs->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(bs->clk)) {
+		err = PTR_ERR(bs->clk);
+		dev_err(&pdev->dev, "could not get clk: %d\n", err);
+		goto out_master_put;
+	}
+
+	bs->irq = irq_of_parse_and_map(pdev->dev.of_node, 0);
+	if (bs->irq <= 0) {
+		dev_err(&pdev->dev, "could not get IRQ: %d\n", bs->irq);
+		err = bs->irq ? bs->irq : -ENODEV;
+		goto out_master_put;
+	}
+
+	clk_prepare_enable(bs->clk);
+
+	err = request_irq(bs->irq, bcm2835_spi_interrupt, 0,
+			dev_name(&pdev->dev), master);
+	if (err) {
+		dev_err(&pdev->dev, "could not request IRQ: %d\n", err);
+		goto out_clk_disable;
+	}
+
+	/* initialise the hardware */
+	bcm2835_wr(bs, BCM2835_SPI_CS,
+		   BCM2835_SPI_CS_CLEAR_RX | BCM2835_SPI_CS_CLEAR_TX);
+
+	err = spi_register_master(master);
+	if (err) {
+		dev_err(&pdev->dev, "could not register SPI master: %d\n", err);
+		goto out_free_irq;
+	}
+
+	return 0;
+
+out_free_irq:
+	free_irq(bs->irq, master);
+out_clk_disable:
+	clk_disable_unprepare(bs->clk);
+out_master_put:
+	spi_master_put(master);
+	return err;
+}
+
+static int bcm2835_spi_remove(struct platform_device *pdev)
+{
+	struct spi_master *master = platform_get_drvdata(pdev);
+	struct bcm2835_spi *bs = spi_master_get_devdata(master);
+
+	free_irq(bs->irq, master);
+	spi_unregister_master(master);
+
+	/* Clear FIFOs, and disable the HW block */
+	bcm2835_wr(bs, BCM2835_SPI_CS,
+		   BCM2835_SPI_CS_CLEAR_RX | BCM2835_SPI_CS_CLEAR_TX);
+
+	clk_disable_unprepare(bs->clk);
+	spi_master_put(master);
+
+	return 0;
+}
+
+static const struct of_device_id bcm2835_spi_match[] = {
+	{ .compatible = "brcm,bcm2835-spi", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, bcm2835_spi_match);
+
+static struct platform_driver bcm2835_spi_driver = {
+	.driver		= {
+		.name		= DRV_NAME,
+		.owner		= THIS_MODULE,
+		.of_match_table	= bcm2835_spi_match,
+	},
+	.probe		= bcm2835_spi_probe,
+	.remove		= bcm2835_spi_remove,
+};
+module_platform_driver(bcm2835_spi_driver);
+
+MODULE_DESCRIPTION("SPI controller driver for Broadcom BCM2835");
+MODULE_AUTHOR("Chris Boot <bootc@bootc.net>");
+MODULE_LICENSE("GPL v2");