bnx2x: Add timestamping and PTP hardware clock support

This adds a PHC to the bnx2x driver. Driver supports timestamping send/receive
PTP packets, as well as adjusting the on-chip clock.

The driver has been tested with linuxptp project.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/ethernet/broadcom/bnx2x/bnx2x.h

@@ -20,6 +20,10 @@
 #include <linux/types.h>
 #include <linux/pci_regs.h>
 
+#include <linux/ptp_clock_kernel.h>
+#include <linux/net_tstamp.h>
+#include <linux/clocksource.h>
+
 /* compilation time flags */
 
 /* define this to make the driver freeze on error to allow getting debug info
@@ -70,6 +74,7 @@ enum bnx2x_int_mode {
 #define BNX2X_MSG_SP			0x0100000 /* was: NETIF_MSG_INTR */
 #define BNX2X_MSG_FP			0x0200000 /* was: NETIF_MSG_INTR */
 #define BNX2X_MSG_IOV			0x0800000
+#define BNX2X_MSG_PTP			0x1000000
 #define BNX2X_MSG_IDLE			0x2000000 /* used for idle check*/
 #define BNX2X_MSG_ETHTOOL		0x4000000
 #define BNX2X_MSG_DCB			0x8000000
@@ -1591,6 +1596,8 @@ struct bnx2x {
 #define BC_SUPPORTS_RMMOD_CMD		(1 << 24)
 #define HAS_PHYS_PORT_ID		(1 << 25)
 #define AER_ENABLED			(1 << 26)
+#define PTP_SUPPORTED			(1 << 27)
+#define TX_TIMESTAMPING_EN		(1 << 28)
 
 #define BP_NOMCP(bp)			((bp)->flags & NO_MCP_FLAG)
 
@@ -1933,6 +1940,19 @@ struct bnx2x {
 
 	u8					phys_port_id[ETH_ALEN];
 
+	/* PTP related context */
+	struct ptp_clock *ptp_clock;
+	struct ptp_clock_info ptp_clock_info;
+	struct work_struct ptp_task;
+	struct cyclecounter cyclecounter;
+	struct timecounter timecounter;
+	bool timecounter_init_done;
+	struct sk_buff *ptp_tx_skb;
+	unsigned long ptp_tx_start;
+	bool hwtstamp_ioctl_called;
+	u16 tx_type;
+	u16 rx_filter;
+
 	struct bnx2x_link_report_data		vf_link_vars;
 };
 
@@ -2559,4 +2579,11 @@ void bnx2x_update_mng_version(struct bnx2x *bp);
 
 #define E1H_MAX_MF_SB_COUNT (HC_SB_MAX_SB_E1X/(E1HVN_MAX * PORT_MAX))
 
+void bnx2x_init_ptp(struct bnx2x *bp);
+int bnx2x_configure_ptp_filters(struct bnx2x *bp);
+void bnx2x_set_rx_ts(struct bnx2x *bp, struct sk_buff *skb);
+
+#define BNX2X_MAX_PHC_DRIFT 31000000
+#define BNX2X_PTP_TX_TIMEOUT
+
 #endif /* bnx2x.h */

drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c

@@ -1067,6 +1067,11 @@ static int bnx2x_rx_int(struct bnx2x_fastpath *fp, int budget)
 
 		skb_record_rx_queue(skb, fp->rx_queue);
 
+		/* Check if this packet was timestamped */
+		if (unlikely(le16_to_cpu(cqe->fast_path_cqe.type_error_flags) &
+			     (1 << ETH_FAST_PATH_RX_CQE_PTP_PKT_SHIFT)))
+			bnx2x_set_rx_ts(bp, skb);
+
 		if (le16_to_cpu(cqe_fp->pars_flags.flags) &
 		    PARSING_FLAGS_VLAN)
 			__vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q),
@@ -2808,7 +2813,11 @@ int bnx2x_nic_load(struct bnx2x *bp, int load_mode)
 	/* Initialize Rx filter. */
 	bnx2x_set_rx_mode_inner(bp);
 
-	/* Start the Tx */
+	if (bp->flags & PTP_SUPPORTED) {
+		bnx2x_init_ptp(bp);
+		bnx2x_configure_ptp_filters(bp);
+	}
+	/* Start Tx */
 	switch (load_mode) {
 	case LOAD_NORMAL:
 		/* Tx queue should be only re-enabled */
@@ -3833,6 +3842,20 @@ netdev_tx_t bnx2x_start_xmit(struct sk_buff *skb, struct net_device *dev)
 
 	tx_start_bd->bd_flags.as_bitfield = ETH_TX_BD_FLAGS_START_BD;
 
+	if (unlikely(skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP)) {
+		if (!(bp->flags & TX_TIMESTAMPING_EN)) {
+			BNX2X_ERR("Tx timestamping was not enabled, this packet will not be timestamped\n");
+		} else if (bp->ptp_tx_skb) {
+			BNX2X_ERR("The device supports only a single outstanding packet to timestamp, this packet will not be timestamped\n");
+		} else {
+			skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS;
+			/* schedule check for Tx timestamp */
+			bp->ptp_tx_skb = skb_get(skb);
+			bp->ptp_tx_start = jiffies;
+			schedule_work(&bp->ptp_task);
+		}
+	}
+
 	/* header nbd: indirectly zero other flags! */
 	tx_start_bd->general_data = 1 << ETH_TX_START_BD_HDR_NBDS_SHIFT;
 

drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c

@@ -3481,6 +3481,46 @@ static int bnx2x_set_channels(struct net_device *dev,
 	return bnx2x_nic_load(bp, LOAD_NORMAL);
 }
 
+static int bnx2x_get_ts_info(struct net_device *dev,
+			     struct ethtool_ts_info *info)
+{
+	struct bnx2x *bp = netdev_priv(dev);
+
+	if (bp->flags & PTP_SUPPORTED) {
+		info->so_timestamping = SOF_TIMESTAMPING_TX_SOFTWARE |
+					SOF_TIMESTAMPING_RX_SOFTWARE |
+					SOF_TIMESTAMPING_SOFTWARE |
+					SOF_TIMESTAMPING_TX_HARDWARE |
+					SOF_TIMESTAMPING_RX_HARDWARE |
+					SOF_TIMESTAMPING_RAW_HARDWARE;
+
+		if (bp->ptp_clock)
+			info->phc_index = ptp_clock_index(bp->ptp_clock);
+		else
+			info->phc_index = -1;
+
+		info->rx_filters = (1 << HWTSTAMP_FILTER_NONE) |
+				   (1 << HWTSTAMP_FILTER_PTP_V1_L4_EVENT) |
+				   (1 << HWTSTAMP_FILTER_PTP_V1_L4_SYNC) |
+				   (1 << HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ) |
+				   (1 << HWTSTAMP_FILTER_PTP_V2_L4_EVENT) |
+				   (1 << HWTSTAMP_FILTER_PTP_V2_L4_SYNC) |
+				   (1 << HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ) |
+				   (1 << HWTSTAMP_FILTER_PTP_V2_L2_EVENT) |
+				   (1 << HWTSTAMP_FILTER_PTP_V2_L2_SYNC) |
+				   (1 << HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ) |
+				   (1 << HWTSTAMP_FILTER_PTP_V2_EVENT) |
+				   (1 << HWTSTAMP_FILTER_PTP_V2_SYNC) |
+				   (1 << HWTSTAMP_FILTER_PTP_V2_DELAY_REQ);
+
+		info->tx_types = (1 << HWTSTAMP_TX_OFF)|(1 << HWTSTAMP_TX_ON);
+
+		return 0;
+	}
+
+	return ethtool_op_get_ts_info(dev, info);
+}
+
 static const struct ethtool_ops bnx2x_ethtool_ops = {
 	.get_settings		= bnx2x_get_settings,
 	.set_settings		= bnx2x_set_settings,
@@ -3522,7 +3562,7 @@ static const struct ethtool_ops bnx2x_ethtool_ops = {
 	.get_module_eeprom	= bnx2x_get_module_eeprom,
 	.get_eee		= bnx2x_get_eee,
 	.set_eee		= bnx2x_set_eee,
-	.get_ts_info		= ethtool_op_get_ts_info,
+	.get_ts_info		= bnx2x_get_ts_info,
 };
 
 static const struct ethtool_ops bnx2x_vf_ethtool_ops = {

drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h

@@ -3547,7 +3547,9 @@ struct client_init_rx_data {
 	__le16 rx_cos_mask;
 	__le16 silent_vlan_value;
 	__le16 silent_vlan_mask;
-	__le32 reserved6[2];
+	u8 handle_ptp_pkts_flg;
+	u8 reserved6[3];
+	__le32 reserved7;
 };
 
 /*
@@ -3616,7 +3618,9 @@ struct client_update_ramrod_data {
 	u8 refuse_outband_vlan_change_flg;
 	u8 tx_switching_flg;
 	u8 tx_switching_change_flg;
-	__le32 reserved1;
+	u8 handle_ptp_pkts_flg;
+	u8 handle_ptp_pkts_change_flg;
+	__le16 reserved1;
 	__le32 echo;
 };
 
@@ -3850,8 +3854,10 @@ struct eth_fast_path_rx_cqe {
 #define ETH_FAST_PATH_RX_CQE_IP_BAD_XSUM_FLG_SHIFT 4
 #define ETH_FAST_PATH_RX_CQE_L4_BAD_XSUM_FLG (0x1<<5)
 #define ETH_FAST_PATH_RX_CQE_L4_BAD_XSUM_FLG_SHIFT 5
-#define ETH_FAST_PATH_RX_CQE_RESERVED0 (0x3<<6)
-#define ETH_FAST_PATH_RX_CQE_RESERVED0_SHIFT 6
+#define ETH_FAST_PATH_RX_CQE_PTP_PKT (0x1<<6)
+#define ETH_FAST_PATH_RX_CQE_PTP_PKT_SHIFT 6
+#define ETH_FAST_PATH_RX_CQE_RESERVED0 (0x1<<7)
+#define ETH_FAST_PATH_RX_CQE_RESERVED0_SHIFT 7
 	u8 status_flags;
 #define ETH_FAST_PATH_RX_CQE_RSS_HASH_TYPE (0x7<<0)
 #define ETH_FAST_PATH_RX_CQE_RSS_HASH_TYPE_SHIFT 0
@@ -5658,6 +5664,16 @@ struct protocol_common_spe {
 	union protocol_common_specific_data data;
 };
 
+/* The data for the Set Timesync Ramrod */
+struct set_timesync_ramrod_data {
+	u8 drift_adjust_cmd;
+	u8 offset_cmd;
+	u8 add_sub_drift_adjust_value;
+	u8 drift_adjust_value;
+	u32 drift_adjust_period;
+	struct regpair offset_delta;
+};
+
 /*
  * The send queue element
  */
@@ -5780,6 +5796,29 @@ struct tstorm_vf_zone_data {
 	struct regpair reserved;
 };
 
+/* Add or Subtract Value for Set Timesync Ramrod */
+enum ts_add_sub_value {
+	TS_SUB_VALUE,
+	TS_ADD_VALUE,
+	MAX_TS_ADD_SUB_VALUE
+};
+
+/* Drift-Adjust Commands for Set Timesync Ramrod */
+enum ts_drift_adjust_cmd {
+	TS_DRIFT_ADJUST_KEEP,
+	TS_DRIFT_ADJUST_SET,
+	TS_DRIFT_ADJUST_RESET,
+	MAX_TS_DRIFT_ADJUST_CMD
+};
+
+/* Offset Commands for Set Timesync Ramrod */
+enum ts_offset_cmd {
+	TS_OFFSET_KEEP,
+	TS_OFFSET_INC,
+	TS_OFFSET_DEC,
+	MAX_TS_OFFSET_CMD
+};
+
 /* Tunnel Mode */
 enum tunnel_mode {
 	TUNN_MODE_NONE,

drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c

@@ -63,7 +63,6 @@
 #include "bnx2x_vfpf.h"
 #include "bnx2x_dcb.h"
 #include "bnx2x_sp.h"
-
 #include <linux/firmware.h>
 #include "bnx2x_fw_file_hdr.h"
 /* FW files */
@@ -290,6 +289,8 @@ static int bnx2x_set_storm_rx_mode(struct bnx2x *bp);
 * General service functions
 ****************************************************************************/
 
+static int bnx2x_hwtstamp_ioctl(struct bnx2x *bp, struct ifreq *ifr);
+
 static void __storm_memset_dma_mapping(struct bnx2x *bp,
 				       u32 addr, dma_addr_t mapping)
 {
@@ -523,6 +524,7 @@ int bnx2x_issue_dmae_with_comp(struct bnx2x *bp, struct dmae_command *dmae,
 	 * as long as this code is called both from syscall context and
 	 * from ndo_set_rx_mode() flow that may be called from BH.
 	 */
+
 	spin_lock_bh(&bp->dmae_lock);
 
 	/* reset completion */
@@ -551,7 +553,9 @@ int bnx2x_issue_dmae_with_comp(struct bnx2x *bp, struct dmae_command *dmae,
 	}
 
 unlock:
+
 	spin_unlock_bh(&bp->dmae_lock);
+
 	return rc;
 }
 
@@ -5452,6 +5456,14 @@ static void bnx2x_eq_int(struct bnx2x *bp)
 				break;
 
 			goto next_spqe;
+
+		case EVENT_RING_OPCODE_SET_TIMESYNC:
+			DP(BNX2X_MSG_SP | BNX2X_MSG_PTP,
+			   "got set_timesync ramrod completion\n");
+			if (f_obj->complete_cmd(bp, f_obj,
+						BNX2X_F_CMD_SET_TIMESYNC))
+				break;
+			goto next_spqe;
 		}
 
 		switch (opcode | bp->state) {
@@ -9033,6 +9045,48 @@ static int bnx2x_func_wait_started(struct bnx2x *bp)
 	return 0;
 }
 
+static void bnx2x_disable_ptp(struct bnx2x *bp)
+{
+	int port = BP_PORT(bp);
+
+	/* Disable sending PTP packets to host */
+	REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_TO_HOST :
+	       NIG_REG_P0_LLH_PTP_TO_HOST, 0x0);
+
+	/* Reset PTP event detection rules */
+	REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_PARAM_MASK :
+	       NIG_REG_P0_LLH_PTP_PARAM_MASK, 0x7FF);
+	REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_RULE_MASK :
+	       NIG_REG_P0_LLH_PTP_RULE_MASK, 0x3FFF);
+	REG_WR(bp, port ? NIG_REG_P1_TLLH_PTP_PARAM_MASK :
+	       NIG_REG_P0_TLLH_PTP_PARAM_MASK, 0x7FF);
+	REG_WR(bp, port ? NIG_REG_P1_TLLH_PTP_RULE_MASK :
+	       NIG_REG_P0_TLLH_PTP_RULE_MASK, 0x3FFF);
+
+	/* Disable the PTP feature */
+	REG_WR(bp, port ? NIG_REG_P1_PTP_EN :
+	       NIG_REG_P0_PTP_EN, 0x0);
+}
+
+/* Called during unload, to stop PTP-related stuff */
+void bnx2x_stop_ptp(struct bnx2x *bp)
+{
+	/* Cancel PTP work queue. Should be done after the Tx queues are
+	 * drained to prevent additional scheduling.
+	 */
+	cancel_work_sync(&bp->ptp_task);
+
+	if (bp->ptp_tx_skb) {
+		dev_kfree_skb_any(bp->ptp_tx_skb);
+		bp->ptp_tx_skb = NULL;
+	}
+
+	/* Disable PTP in HW */
+	bnx2x_disable_ptp(bp);
+
+	DP(BNX2X_MSG_PTP, "PTP stop ended successfully\n");
+}
+
 void bnx2x_chip_cleanup(struct bnx2x *bp, int unload_mode, bool keep_link)
 {
 	int port = BP_PORT(bp);
@@ -9151,6 +9205,13 @@ void bnx2x_chip_cleanup(struct bnx2x *bp, int unload_mode, bool keep_link)
 #endif
 	}
 
+	/* stop_ptp should be after the Tx queues are drained to prevent
+	 * scheduling to the cancelled PTP work queue. It should also be after
+	 * function stop ramrod is sent, since as part of this ramrod FW access
+	 * PTP registers.
+	 */
+	bnx2x_stop_ptp(bp);
+
 	/* Disable HW interrupts, NAPI */
 	bnx2x_netif_stop(bp, 1);
 	/* Delete all NAPI objects */
@@ -12023,6 +12084,9 @@ static int bnx2x_init_bp(struct bnx2x *bp)
 
 	bp->dump_preset_idx = 1;
 
+	if (CHIP_IS_E3B0(bp))
+		bp->flags |= PTP_SUPPORTED;
+
 	return rc;
 }
 
@@ -12355,13 +12419,17 @@ static int bnx2x_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
 	struct bnx2x *bp = netdev_priv(dev);
 	struct mii_ioctl_data *mdio = if_mii(ifr);
 
-	DP(NETIF_MSG_LINK, "ioctl: phy id 0x%x, reg 0x%x, val_in 0x%x\n",
-	   mdio->phy_id, mdio->reg_num, mdio->val_in);
-
 	if (!netif_running(dev))
 		return -EAGAIN;
 
+	switch (cmd) {
+	case SIOCSHWTSTAMP:
+		return bnx2x_hwtstamp_ioctl(bp, ifr);
+	default:
+		DP(NETIF_MSG_LINK, "ioctl: phy id 0x%x, reg 0x%x, val_in 0x%x\n",
+		   mdio->phy_id, mdio->reg_num, mdio->val_in);
 		return mdio_mii_ioctl(&bp->mdio, mdio, cmd);
+	}
 }
 
 #ifdef CONFIG_NET_POLL_CONTROLLER
@@ -13005,6 +13073,191 @@ static int set_is_vf(int chip_id)
 	}
 }
 
+/* nig_tsgen registers relative address */
+#define tsgen_ctrl 0x0
+#define tsgen_freecount 0x10
+#define tsgen_synctime_t0 0x20
+#define tsgen_offset_t0 0x28
+#define tsgen_drift_t0 0x30
+#define tsgen_synctime_t1 0x58
+#define tsgen_offset_t1 0x60
+#define tsgen_drift_t1 0x68
+
+/* FW workaround for setting drift */
+static int bnx2x_send_update_drift_ramrod(struct bnx2x *bp, int drift_dir,
+					  int best_val, int best_period)
+{
+	struct bnx2x_func_state_params func_params = {NULL};
+	struct bnx2x_func_set_timesync_params *set_timesync_params =
+		&func_params.params.set_timesync;
+
+	/* Prepare parameters for function state transitions */
+	__set_bit(RAMROD_COMP_WAIT, &func_params.ramrod_flags);
+	__set_bit(RAMROD_RETRY, &func_params.ramrod_flags);
+
+	func_params.f_obj = &bp->func_obj;
+	func_params.cmd = BNX2X_F_CMD_SET_TIMESYNC;
+
+	/* Function parameters */
+	set_timesync_params->drift_adjust_cmd = TS_DRIFT_ADJUST_SET;
+	set_timesync_params->offset_cmd = TS_OFFSET_KEEP;
+	set_timesync_params->add_sub_drift_adjust_value =
+		drift_dir ? TS_ADD_VALUE : TS_SUB_VALUE;
+	set_timesync_params->drift_adjust_value = best_val;
+	set_timesync_params->drift_adjust_period = best_period;
+
+	return bnx2x_func_state_change(bp, &func_params);
+}
+
+static int bnx2x_ptp_adjfreq(struct ptp_clock_info *ptp, s32 ppb)
+{
+	struct bnx2x *bp = container_of(ptp, struct bnx2x, ptp_clock_info);
+	int rc;
+	int drift_dir = 1;
+	int val, period, period1, period2, dif, dif1, dif2;
+	int best_dif = BNX2X_MAX_PHC_DRIFT, best_period = 0, best_val = 0;
+
+	DP(BNX2X_MSG_PTP, "PTP adjfreq called, ppb = %d\n", ppb);
+
+	if (!netif_running(bp->dev)) {
+		DP(BNX2X_MSG_PTP,
+		   "PTP adjfreq called while the interface is down\n");
+		return -EFAULT;
+	}
+
+	if (ppb < 0) {
+		ppb = -ppb;
+		drift_dir = 0;
+	}
+
+	if (ppb == 0) {
+		best_val = 1;
+		best_period = 0x1FFFFFF;
+	} else if (ppb >= BNX2X_MAX_PHC_DRIFT) {
+		best_val = 31;
+		best_period = 1;
+	} else {
+		/* Changed not to allow val = 8, 16, 24 as these values
+		 * are not supported in workaround.
+		 */
+		for (val = 0; val <= 31; val++) {
+			if ((val & 0x7) == 0)
+				continue;
+			period1 = val * 1000000 / ppb;
+			period2 = period1 + 1;
+			if (period1 != 0)
+				dif1 = ppb - (val * 1000000 / period1);
+			else
+				dif1 = BNX2X_MAX_PHC_DRIFT;
+			if (dif1 < 0)
+				dif1 = -dif1;
+			dif2 = ppb - (val * 1000000 / period2);
+			if (dif2 < 0)
+				dif2 = -dif2;
+			dif = (dif1 < dif2) ? dif1 : dif2;
+			period = (dif1 < dif2) ? period1 : period2;
+			if (dif < best_dif) {
+				best_dif = dif;
+				best_val = val;
+				best_period = period;
+			}
+		}
+	}
+
+	rc = bnx2x_send_update_drift_ramrod(bp, drift_dir, best_val,
+					    best_period);
+	if (rc) {
+		BNX2X_ERR("Failed to set drift\n");
+		return -EFAULT;
+	}
+
+	DP(BNX2X_MSG_PTP, "Configrued val = %d, period = %d\n", best_val,
+	   best_period);
+
+	return 0;
+}
+
+static int bnx2x_ptp_adjtime(struct ptp_clock_info *ptp, s64 delta)
+{
+	struct bnx2x *bp = container_of(ptp, struct bnx2x, ptp_clock_info);
+	u64 now;
+
+	DP(BNX2X_MSG_PTP, "PTP adjtime called, delta = %llx\n", delta);
+
+	now = timecounter_read(&bp->timecounter);
+	now += delta;
+	/* Re-init the timecounter */
+	timecounter_init(&bp->timecounter, &bp->cyclecounter, now);
+
+	return 0;
+}
+
+static int bnx2x_ptp_gettime(struct ptp_clock_info *ptp, struct timespec *ts)
+{
+	struct bnx2x *bp = container_of(ptp, struct bnx2x, ptp_clock_info);
+	u64 ns;
+	u32 remainder;
+
+	ns = timecounter_read(&bp->timecounter);
+
+	DP(BNX2X_MSG_PTP, "PTP gettime called, ns = %llu\n", ns);
+
+	ts->tv_sec = div_u64_rem(ns, 1000000000ULL, &remainder);
+	ts->tv_nsec = remainder;
+
+	return 0;
+}
+
+static int bnx2x_ptp_settime(struct ptp_clock_info *ptp,
+			     const struct timespec *ts)
+{
+	struct bnx2x *bp = container_of(ptp, struct bnx2x, ptp_clock_info);
+	u64 ns;
+
+	ns = ts->tv_sec * 1000000000ULL;
+	ns += ts->tv_nsec;
+
+	DP(BNX2X_MSG_PTP, "PTP settime called, ns = %llu\n", ns);
+
+	/* Re-init the timecounter */
+	timecounter_init(&bp->timecounter, &bp->cyclecounter, ns);
+
+	return 0;
+}
+
+/* Enable (or disable) ancillary features of the phc subsystem */
+static int bnx2x_ptp_enable(struct ptp_clock_info *ptp,
+			    struct ptp_clock_request *rq, int on)
+{
+	struct bnx2x *bp = container_of(ptp, struct bnx2x, ptp_clock_info);
+
+	BNX2X_ERR("PHC ancillary features are not supported\n");
+	return -ENOTSUPP;
+}
+
+void bnx2x_register_phc(struct bnx2x *bp)
+{
+	/* Fill the ptp_clock_info struct and register PTP clock*/
+	bp->ptp_clock_info.owner = THIS_MODULE;
+	snprintf(bp->ptp_clock_info.name, 16, "%s", bp->dev->name);
+	bp->ptp_clock_info.max_adj = BNX2X_MAX_PHC_DRIFT; /* In PPB */
+	bp->ptp_clock_info.n_alarm = 0;
+	bp->ptp_clock_info.n_ext_ts = 0;
+	bp->ptp_clock_info.n_per_out = 0;
+	bp->ptp_clock_info.pps = 0;
+	bp->ptp_clock_info.adjfreq = bnx2x_ptp_adjfreq;
+	bp->ptp_clock_info.adjtime = bnx2x_ptp_adjtime;
+	bp->ptp_clock_info.gettime = bnx2x_ptp_gettime;
+	bp->ptp_clock_info.settime = bnx2x_ptp_settime;
+	bp->ptp_clock_info.enable = bnx2x_ptp_enable;
+
+	bp->ptp_clock = ptp_clock_register(&bp->ptp_clock_info, &bp->pdev->dev);
+	if (IS_ERR(bp->ptp_clock)) {
+		bp->ptp_clock = NULL;
+		BNX2X_ERR("PTP clock registeration failed\n");
+	}
+}
+
 static int bnx2x_init_one(struct pci_dev *pdev,
 				    const struct pci_device_id *ent)
 {
@@ -13176,6 +13429,8 @@ static int bnx2x_init_one(struct pci_dev *pdev,
 		       "Unknown",
 		       dev->base_addr, bp->pdev->irq, dev->dev_addr);
 
+	bnx2x_register_phc(bp);
+
 	return 0;
 
 init_one_exit:
@@ -13202,6 +13457,11 @@ static void __bnx2x_remove(struct pci_dev *pdev,
 			   struct bnx2x *bp,
 			   bool remove_netdev)
 {
+	if (bp->ptp_clock) {
+		ptp_clock_unregister(bp->ptp_clock);
+		bp->ptp_clock = NULL;
+	}
+
 	/* Delete storage MAC address */
 	if (!NO_FCOE(bp)) {
 		rtnl_lock();
@@ -14177,3 +14437,332 @@ int bnx2x_pretend_func(struct bnx2x *bp, u16 pretend_func_val)
 	REG_RD(bp, pretend_reg);
 	return 0;
 }
+
+static void bnx2x_ptp_task(struct work_struct *work)
+{
+	struct bnx2x *bp = container_of(work, struct bnx2x, ptp_task);
+	int port = BP_PORT(bp);
+	u32 val_seq;
+	u64 timestamp, ns;
+	struct skb_shared_hwtstamps shhwtstamps;
+
+	/* Read Tx timestamp registers */
+	val_seq = REG_RD(bp, port ? NIG_REG_P1_TLLH_PTP_BUF_SEQID :
+			 NIG_REG_P0_TLLH_PTP_BUF_SEQID);
+	if (val_seq & 0x10000) {
+		/* There is a valid timestamp value */
+		timestamp = REG_RD(bp, port ? NIG_REG_P1_TLLH_PTP_BUF_TS_MSB :
+				   NIG_REG_P0_TLLH_PTP_BUF_TS_MSB);
+		timestamp <<= 32;
+		timestamp |= REG_RD(bp, port ? NIG_REG_P1_TLLH_PTP_BUF_TS_LSB :
+				    NIG_REG_P0_TLLH_PTP_BUF_TS_LSB);
+		/* Reset timestamp register to allow new timestamp */
+		REG_WR(bp, port ? NIG_REG_P1_TLLH_PTP_BUF_SEQID :
+		       NIG_REG_P0_TLLH_PTP_BUF_SEQID, 0x10000);
+		ns = timecounter_cyc2time(&bp->timecounter, timestamp);
+
+		memset(&shhwtstamps, 0, sizeof(shhwtstamps));
+		shhwtstamps.hwtstamp = ns_to_ktime(ns);
+		skb_tstamp_tx(bp->ptp_tx_skb, &shhwtstamps);
+		dev_kfree_skb_any(bp->ptp_tx_skb);
+		bp->ptp_tx_skb = NULL;
+
+		DP(BNX2X_MSG_PTP, "Tx timestamp, timestamp cycles = %llu, ns = %llu\n",
+		   timestamp, ns);
+	} else {
+		DP(BNX2X_MSG_PTP, "There is no valid Tx timestamp yet\n");
+		/* Reschedule to keep checking for a valid timestamp value */
+		schedule_work(&bp->ptp_task);
+	}
+}
+
+void bnx2x_set_rx_ts(struct bnx2x *bp, struct sk_buff *skb)
+{
+	int port = BP_PORT(bp);
+	u64 timestamp, ns;
+
+	timestamp = REG_RD(bp, port ? NIG_REG_P1_LLH_PTP_HOST_BUF_TS_MSB :
+			    NIG_REG_P0_LLH_PTP_HOST_BUF_TS_MSB);
+	timestamp <<= 32;
+	timestamp |= REG_RD(bp, port ? NIG_REG_P1_LLH_PTP_HOST_BUF_TS_LSB :
+			    NIG_REG_P0_LLH_PTP_HOST_BUF_TS_LSB);
+
+	/* Reset timestamp register to allow new timestamp */
+	REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_HOST_BUF_SEQID :
+	       NIG_REG_P0_LLH_PTP_HOST_BUF_SEQID, 0x10000);
+
+	ns = timecounter_cyc2time(&bp->timecounter, timestamp);
+
+	skb_hwtstamps(skb)->hwtstamp = ns_to_ktime(ns);
+
+	DP(BNX2X_MSG_PTP, "Rx timestamp, timestamp cycles = %llu, ns = %llu\n",
+	   timestamp, ns);
+}
+
+/* Read the PHC */
+static cycle_t bnx2x_cyclecounter_read(const struct cyclecounter *cc)
+{
+	struct bnx2x *bp = container_of(cc, struct bnx2x, cyclecounter);
+	int port = BP_PORT(bp);
+	u32 wb_data[2];
+	u64 phc_cycles;
+
+	REG_RD_DMAE(bp, port ? NIG_REG_TIMESYNC_GEN_REG + tsgen_synctime_t1 :
+		    NIG_REG_TIMESYNC_GEN_REG + tsgen_synctime_t0, wb_data, 2);
+	phc_cycles = wb_data[1];
+	phc_cycles = (phc_cycles << 32) + wb_data[0];
+
+	DP(BNX2X_MSG_PTP, "PHC read cycles = %llu\n", phc_cycles);
+
+	return phc_cycles;
+}
+
+static void bnx2x_init_cyclecounter(struct bnx2x *bp)
+{
+	memset(&bp->cyclecounter, 0, sizeof(bp->cyclecounter));
+	bp->cyclecounter.read = bnx2x_cyclecounter_read;
+	bp->cyclecounter.mask = CLOCKSOURCE_MASK(64);
+	bp->cyclecounter.shift = 1;
+	bp->cyclecounter.mult = 1;
+}
+
+static int bnx2x_send_reset_timesync_ramrod(struct bnx2x *bp)
+{
+	struct bnx2x_func_state_params func_params = {NULL};
+	struct bnx2x_func_set_timesync_params *set_timesync_params =
+		&func_params.params.set_timesync;
+
+	/* Prepare parameters for function state transitions */
+	__set_bit(RAMROD_COMP_WAIT, &func_params.ramrod_flags);
+	__set_bit(RAMROD_RETRY, &func_params.ramrod_flags);
+
+	func_params.f_obj = &bp->func_obj;
+	func_params.cmd = BNX2X_F_CMD_SET_TIMESYNC;
+
+	/* Function parameters */
+	set_timesync_params->drift_adjust_cmd = TS_DRIFT_ADJUST_RESET;
+	set_timesync_params->offset_cmd = TS_OFFSET_KEEP;
+
+	return bnx2x_func_state_change(bp, &func_params);
+}
+
+int bnx2x_enable_ptp_packets(struct bnx2x *bp)
+{
+	struct bnx2x_queue_state_params q_params;
+	int rc, i;
+
+	/* send queue update ramrod to enable PTP packets */
+	memset(&q_params, 0, sizeof(q_params));
+	__set_bit(RAMROD_COMP_WAIT, &q_params.ramrod_flags);
+	q_params.cmd = BNX2X_Q_CMD_UPDATE;
+	__set_bit(BNX2X_Q_UPDATE_PTP_PKTS_CHNG,
+		  &q_params.params.update.update_flags);
+	__set_bit(BNX2X_Q_UPDATE_PTP_PKTS,
+		  &q_params.params.update.update_flags);
+
+	/* send the ramrod on all the queues of the PF */
+	for_each_eth_queue(bp, i) {
+		struct bnx2x_fastpath *fp = &bp->fp[i];
+
+		/* Set the appropriate Queue object */
+		q_params.q_obj = &bnx2x_sp_obj(bp, fp).q_obj;
+
+		/* Update the Queue state */
+		rc = bnx2x_queue_state_change(bp, &q_params);
+		if (rc) {
+			BNX2X_ERR("Failed to enable PTP packets\n");
+			return rc;
+		}
+	}
+
+	return 0;
+}
+
+int bnx2x_configure_ptp_filters(struct bnx2x *bp)
+{
+	int port = BP_PORT(bp);
+	int rc;
+
+	if (!bp->hwtstamp_ioctl_called)
+		return 0;
+
+	switch (bp->tx_type) {
+	case HWTSTAMP_TX_ON:
+		bp->flags |= TX_TIMESTAMPING_EN;
+		REG_WR(bp, port ? NIG_REG_P1_TLLH_PTP_PARAM_MASK :
+		       NIG_REG_P0_TLLH_PTP_PARAM_MASK, 0x6AA);
+		REG_WR(bp, port ? NIG_REG_P1_TLLH_PTP_RULE_MASK :
+		       NIG_REG_P0_TLLH_PTP_RULE_MASK, 0x3EEE);
+		break;
+	case HWTSTAMP_TX_ONESTEP_SYNC:
+		BNX2X_ERR("One-step timestamping is not supported\n");
+		return -ERANGE;
+	}
+
+	switch (bp->rx_filter) {
+	case HWTSTAMP_FILTER_NONE:
+		break;
+	case HWTSTAMP_FILTER_ALL:
+	case HWTSTAMP_FILTER_SOME:
+		bp->rx_filter = HWTSTAMP_FILTER_NONE;
+		break;
+	case HWTSTAMP_FILTER_PTP_V1_L4_EVENT:
+	case HWTSTAMP_FILTER_PTP_V1_L4_SYNC:
+	case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ:
+		bp->rx_filter = HWTSTAMP_FILTER_PTP_V1_L4_EVENT;
+		/* Initialize PTP detection for UDP/IPv4 events */
+		REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_PARAM_MASK :
+		       NIG_REG_P0_LLH_PTP_PARAM_MASK, 0x7EE);
+		REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_RULE_MASK :
+		       NIG_REG_P0_LLH_PTP_RULE_MASK, 0x3FFE);
+		break;
+	case HWTSTAMP_FILTER_PTP_V2_L4_EVENT:
+	case HWTSTAMP_FILTER_PTP_V2_L4_SYNC:
+	case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ:
+		bp->rx_filter = HWTSTAMP_FILTER_PTP_V2_L4_EVENT;
+		/* Initialize PTP detection for UDP/IPv4 or UDP/IPv6 events */
+		REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_PARAM_MASK :
+		       NIG_REG_P0_LLH_PTP_PARAM_MASK, 0x7EA);
+		REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_RULE_MASK :
+		       NIG_REG_P0_LLH_PTP_RULE_MASK, 0x3FEE);
+		break;
+	case HWTSTAMP_FILTER_PTP_V2_L2_EVENT:
+	case HWTSTAMP_FILTER_PTP_V2_L2_SYNC:
+	case HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ:
+		bp->rx_filter = HWTSTAMP_FILTER_PTP_V2_L2_EVENT;
+		/* Initialize PTP detection L2 events */
+		REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_PARAM_MASK :
+		       NIG_REG_P0_LLH_PTP_PARAM_MASK, 0x6BF);
+		REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_RULE_MASK :
+		       NIG_REG_P0_LLH_PTP_RULE_MASK, 0x3EFF);
+
+		break;
+	case HWTSTAMP_FILTER_PTP_V2_EVENT:
+	case HWTSTAMP_FILTER_PTP_V2_SYNC:
+	case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ:
+		bp->rx_filter = HWTSTAMP_FILTER_PTP_V2_EVENT;
+		/* Initialize PTP detection L2, UDP/IPv4 or UDP/IPv6 events */
+		REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_PARAM_MASK :
+		       NIG_REG_P0_LLH_PTP_PARAM_MASK, 0x6AA);
+		REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_RULE_MASK :
+		       NIG_REG_P0_LLH_PTP_RULE_MASK, 0x3EEE);
+		break;
+	}
+
+	/* Indicate to FW that this PF expects recorded PTP packets */
+	rc = bnx2x_enable_ptp_packets(bp);
+	if (rc)
+		return rc;
+
+	/* Enable sending PTP packets to host */
+	REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_TO_HOST :
+	       NIG_REG_P0_LLH_PTP_TO_HOST, 0x1);
+
+	return 0;
+}
+
+static int bnx2x_hwtstamp_ioctl(struct bnx2x *bp, struct ifreq *ifr)
+{
+	struct hwtstamp_config config;
+	int rc;
+
+	DP(BNX2X_MSG_PTP, "HWTSTAMP IOCTL called\n");
+
+	if (copy_from_user(&config, ifr->ifr_data, sizeof(config)))
+		return -EFAULT;
+
+	DP(BNX2X_MSG_PTP, "Requested tx_type: %d, requested rx_filters = %d\n",
+	   config.tx_type, config.rx_filter);
+
+	if (config.flags) {
+		BNX2X_ERR("config.flags is reserved for future use\n");
+		return -EINVAL;
+	}
+
+	bp->hwtstamp_ioctl_called = 1;
+	bp->tx_type = config.tx_type;
+	bp->rx_filter = config.rx_filter;
+
+	rc = bnx2x_configure_ptp_filters(bp);
+	if (rc)
+		return rc;
+
+	config.rx_filter = bp->rx_filter;
+
+	return copy_to_user(ifr->ifr_data, &config, sizeof(config)) ?
+		-EFAULT : 0;
+}
+
+/* Configrues HW for PTP */
+static int bnx2x_configure_ptp(struct bnx2x *bp)
+{
+	int rc, port = BP_PORT(bp);
+	u32 wb_data[2];
+
+	/* Reset PTP event detection rules - will be configured in the IOCTL */
+	REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_PARAM_MASK :
+	       NIG_REG_P0_LLH_PTP_PARAM_MASK, 0x7FF);
+	REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_RULE_MASK :
+	       NIG_REG_P0_LLH_PTP_RULE_MASK, 0x3FFF);
+	REG_WR(bp, port ? NIG_REG_P1_TLLH_PTP_PARAM_MASK :
+	       NIG_REG_P0_TLLH_PTP_PARAM_MASK, 0x7FF);
+	REG_WR(bp, port ? NIG_REG_P1_TLLH_PTP_RULE_MASK :
+	       NIG_REG_P0_TLLH_PTP_RULE_MASK, 0x3FFF);
+
+	/* Disable PTP packets to host - will be configured in the IOCTL*/
+	REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_TO_HOST :
+	       NIG_REG_P0_LLH_PTP_TO_HOST, 0x0);
+
+	/* Enable the PTP feature */
+	REG_WR(bp, port ? NIG_REG_P1_PTP_EN :
+	       NIG_REG_P0_PTP_EN, 0x3F);
+
+	/* Enable the free-running counter */
+	wb_data[0] = 0;
+	wb_data[1] = 0;
+	REG_WR_DMAE(bp, NIG_REG_TIMESYNC_GEN_REG + tsgen_ctrl, wb_data, 2);
+
+	/* Reset drift register (offset register is not reset) */
+	rc = bnx2x_send_reset_timesync_ramrod(bp);
+	if (rc) {
+		BNX2X_ERR("Failed to reset PHC drift register\n");
+		return -EFAULT;
+	}
+
+	/* Reset possibly old timestamps */
+	REG_WR(bp, port ? NIG_REG_P1_LLH_PTP_HOST_BUF_SEQID :
+	       NIG_REG_P0_LLH_PTP_HOST_BUF_SEQID, 0x10000);
+	REG_WR(bp, port ? NIG_REG_P1_TLLH_PTP_BUF_SEQID :
+	       NIG_REG_P0_TLLH_PTP_BUF_SEQID, 0x10000);
+
+	return 0;
+}
+
+/* Called during load, to initialize PTP-related stuff */
+void bnx2x_init_ptp(struct bnx2x *bp)
+{
+	int rc;
+
+	/* Configure PTP in HW */
+	rc = bnx2x_configure_ptp(bp);
+	if (rc) {
+		BNX2X_ERR("Stopping PTP initialization\n");
+		return;
+	}
+
+	/* Init work queue for Tx timestamping */
+	INIT_WORK(&bp->ptp_task, bnx2x_ptp_task);
+
+	/* Init cyclecounter and timecounter. This is done only in the first
+	 * load. If done in every load, PTP application will fail when doing
+	 * unload / load (e.g. MTU change) while it is running.
+	 */
+	if (!bp->timecounter_init_done) {
+		bnx2x_init_cyclecounter(bp);
+		timecounter_init(&bp->timecounter, &bp->cyclecounter,
+				 ktime_to_ns(ktime_get_real()));
+		bp->timecounter_init_done = 1;
+	}
+
+	DP(BNX2X_MSG_PTP, "PTP initialization ended successfully\n");
+}

drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h

@@ -2182,6 +2182,45 @@
 #define NIG_REG_P0_HWPFC_ENABLE				 0x18078
 #define NIG_REG_P0_LLH_FUNC_MEM2				 0x18480
 #define NIG_REG_P0_LLH_FUNC_MEM2_ENABLE			 0x18440
+/* [RW 17] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * the host. Bits [15:0] return the sequence ID of the packet. Bit 16
+ * indicates the validity of the data in the buffer. Writing a 1 to bit 16
+ * will clear the buffer.
+ */
+#define NIG_REG_P0_LLH_PTP_HOST_BUF_SEQID			 0x1875c
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * the host. This location returns the lower 32 bits of timestamp value.
+ */
+#define NIG_REG_P0_LLH_PTP_HOST_BUF_TS_LSB			 0x18754
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * the host. This location returns the upper 32 bits of timestamp value.
+ */
+#define NIG_REG_P0_LLH_PTP_HOST_BUF_TS_MSB			 0x18758
+/* [RW 11] Mask register for the various parameters used in determining PTP
+ * packet presence. Set each bit to 1 to mask out the particular parameter.
+ * 0-IPv4 DA 0 of 224.0.1.129. 1-IPv4 DA 1 of 224.0.0.107. 2-IPv6 DA 0 of
+ * 0xFF0*:0:0:0:0:0:0:181. 3-IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B. 4-UDP
+ * destination port 0 of 319. 5-UDP destination port 1 of 320. 6-MAC
+ * Ethertype 0 of 0x88F7. 7-configurable MAC Ethertype 1. 8-MAC DA 0 of
+ * 0x01-1B-19-00-00-00. 9-MAC DA 1 of 0x01-80-C2-00-00-0E. 10-configurable
+ * MAC DA 2. The reset default is set to mask out all parameters.
+ */
+#define NIG_REG_P0_LLH_PTP_PARAM_MASK				 0x187a0
+/* [RW 14] Mask regiser for the rules used in detecting PTP packets. Set
+ * each bit to 1 to mask out that particular rule. 0-{IPv4 DA 0; UDP DP 0} .
+ * 1-{IPv4 DA 0; UDP DP 1} . 2-{IPv4 DA 1; UDP DP 0} . 3-{IPv4 DA 1; UDP DP
+ * 1} . 4-{IPv6 DA 0; UDP DP 0} . 5-{IPv6 DA 0; UDP DP 1} . 6-{IPv6 DA 1;
+ * UDP DP 0} . 7-{IPv6 DA 1; UDP DP 1} . 8-{MAC DA 0; Ethertype 0} . 9-{MAC
+ * DA 1; Ethertype 0} . 10-{MAC DA 0; Ethertype 1} . 11-{MAC DA 1; Ethertype
+ * 1} . 12-{MAC DA 2; Ethertype 0} . 13-{MAC DA 2; Ethertype 1} . The reset
+ * default is to mask out all of the rules. Note that rules 0-3 are for IPv4
+ * packets only and require that the packet is IPv4 for the rules to match.
+ * Note that rules 4-7 are for IPv6 packets only and require that the packet
+ * is IPv6 for the rules to match.
+ */
+#define NIG_REG_P0_LLH_PTP_RULE_MASK				 0x187a4
+/* [RW 1] Set to 1 to enable PTP packets to be forwarded to the host. */
+#define NIG_REG_P0_LLH_PTP_TO_HOST				 0x187ac
 /* [RW 1] Input enable for RX MAC interface. */
 #define NIG_REG_P0_MAC_IN_EN					 0x185ac
 /* [RW 1] Output enable for TX MAC interface */
@@ -2194,6 +2233,17 @@
  * priority field is extracted from the outer-most VLAN in receive packet.
  * Only COS 0 and COS 1 are supported in E2. */
 #define NIG_REG_P0_PKT_PRIORITY_TO_COS				 0x18054
+/* [RW 6] Enable for TimeSync feature. Bits [2:0] are for RX side. Bits
+ * [5:3] are for TX side. Bit 0 enables TimeSync on RX side. Bit 1 enables
+ * V1 frame format in timesync event detection on RX side. Bit 2 enables V2
+ * frame format in timesync event detection on RX side. Bit 3 enables
+ * TimeSync on TX side. Bit 4 enables V1 frame format in timesync event
+ * detection on TX side. Bit 5 enables V2 frame format in timesync event
+ * detection on TX side. Note that for HW to detect PTP packet and extract
+ * data from the packet, at least one of the version bits of that traffic
+ * direction has to be enabled.
+ */
+#define NIG_REG_P0_PTP_EN					 0x18788
 /* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 0. A
  * priority is mapped to COS 0 when the corresponding mask bit is 1. More
  * than one bit may be set; allowing multiple priorities to be mapped to one
@@ -2300,7 +2350,46 @@
  * Ethernet header. */
 #define NIG_REG_P1_HDRS_AFTER_BASIC				 0x1818c
 #define NIG_REG_P1_LLH_FUNC_MEM2				 0x184c0
-#define NIG_REG_P1_LLH_FUNC_MEM2_ENABLE			 0x18460
+#define NIG_REG_P1_LLH_FUNC_MEM2_ENABLE			 0x18460a
+/* [RW 17] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * the host. Bits [15:0] return the sequence ID of the packet. Bit 16
+ * indicates the validity of the data in the buffer. Writing a 1 to bit 16
+ * will clear the buffer.
+ */
+#define NIG_REG_P1_LLH_PTP_HOST_BUF_SEQID			 0x18774
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * the host. This location returns the lower 32 bits of timestamp value.
+ */
+#define NIG_REG_P1_LLH_PTP_HOST_BUF_TS_LSB			 0x1876c
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * the host. This location returns the upper 32 bits of timestamp value.
+ */
+#define NIG_REG_P1_LLH_PTP_HOST_BUF_TS_MSB			 0x18770
+/* [RW 11] Mask register for the various parameters used in determining PTP
+ * packet presence. Set each bit to 1 to mask out the particular parameter.
+ * 0-IPv4 DA 0 of 224.0.1.129. 1-IPv4 DA 1 of 224.0.0.107. 2-IPv6 DA 0 of
+ * 0xFF0*:0:0:0:0:0:0:181. 3-IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B. 4-UDP
+ * destination port 0 of 319. 5-UDP destination port 1 of 320. 6-MAC
+ * Ethertype 0 of 0x88F7. 7-configurable MAC Ethertype 1. 8-MAC DA 0 of
+ * 0x01-1B-19-00-00-00. 9-MAC DA 1 of 0x01-80-C2-00-00-0E. 10-configurable
+ * MAC DA 2. The reset default is set to mask out all parameters.
+ */
+#define NIG_REG_P1_LLH_PTP_PARAM_MASK				 0x187c8
+/* [RW 14] Mask regiser for the rules used in detecting PTP packets. Set
+ * each bit to 1 to mask out that particular rule. 0-{IPv4 DA 0; UDP DP 0} .
+ * 1-{IPv4 DA 0; UDP DP 1} . 2-{IPv4 DA 1; UDP DP 0} . 3-{IPv4 DA 1; UDP DP
+ * 1} . 4-{IPv6 DA 0; UDP DP 0} . 5-{IPv6 DA 0; UDP DP 1} . 6-{IPv6 DA 1;
+ * UDP DP 0} . 7-{IPv6 DA 1; UDP DP 1} . 8-{MAC DA 0; Ethertype 0} . 9-{MAC
+ * DA 1; Ethertype 0} . 10-{MAC DA 0; Ethertype 1} . 11-{MAC DA 1; Ethertype
+ * 1} . 12-{MAC DA 2; Ethertype 0} . 13-{MAC DA 2; Ethertype 1} . The reset
+ * default is to mask out all of the rules. Note that rules 0-3 are for IPv4
+ * packets only and require that the packet is IPv4 for the rules to match.
+ * Note that rules 4-7 are for IPv6 packets only and require that the packet
+ * is IPv6 for the rules to match.
+ */
+#define NIG_REG_P1_LLH_PTP_RULE_MASK				 0x187cc
+/* [RW 1] Set to 1 to enable PTP packets to be forwarded to the host. */
+#define NIG_REG_P1_LLH_PTP_TO_HOST				 0x187d4
 /* [RW 32] Specify the client number to be assigned to each priority of the
  * strict priority arbiter. This register specifies bits 31:0 of the 36-bit
  * value. Priority 0 is the highest priority. Bits [3:0] are for priority 0
@@ -2342,6 +2431,17 @@
  * priority field is extracted from the outer-most VLAN in receive packet.
  * Only COS 0 and COS 1 are supported in E2. */
 #define NIG_REG_P1_PKT_PRIORITY_TO_COS				 0x181a8
+/* [RW 6] Enable for TimeSync feature. Bits [2:0] are for RX side. Bits
+ * [5:3] are for TX side. Bit 0 enables TimeSync on RX side. Bit 1 enables
+ * V1 frame format in timesync event detection on RX side. Bit 2 enables V2
+ * frame format in timesync event detection on RX side. Bit 3 enables
+ * TimeSync on TX side. Bit 4 enables V1 frame format in timesync event
+ * detection on TX side. Bit 5 enables V2 frame format in timesync event
+ * detection on TX side. Note that for HW to detect PTP packet and extract
+ * data from the packet, at least one of the version bits of that traffic
+ * direction has to be enabled.
+ */
+#define NIG_REG_P1_PTP_EN					 0x187b0
 /* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 0. A
  * priority is mapped to COS 0 when the corresponding mask bit is 1. More
  * than one bit may be set; allowing multiple priorities to be mapped to one
@@ -2361,6 +2461,78 @@
 #define NIG_REG_P1_RX_MACFIFO_EMPTY				 0x1858c
 /* [R 1] TLLH FIFO is empty. */
 #define NIG_REG_P1_TLLH_FIFO_EMPTY				 0x18338
+/* [RW 19] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * TX side. Bits [15:0] reflect the sequence ID of the packet. Bit 16
+ * indicates the validity of the data in the buffer. Bit 17 indicates that
+ * the sequence ID is valid and it is waiting for the TX timestamp value.
+ * Bit 18 indicates whether the timestamp is from a SW request (value of 1)
+ * or HW request (value of 0). Writing a 1 to bit 16 will clear the buffer.
+ */
+#define NIG_REG_P0_TLLH_PTP_BUF_SEQID				 0x187e0
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * MCP. This location returns the lower 32 bits of timestamp value.
+ */
+#define NIG_REG_P0_TLLH_PTP_BUF_TS_LSB				 0x187d8
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * MCP. This location returns the upper 32 bits of timestamp value.
+ */
+#define NIG_REG_P0_TLLH_PTP_BUF_TS_MSB				 0x187dc
+/* [RW 11] Mask register for the various parameters used in determining PTP
+ * packet presence. Set each bit to 1 to mask out the particular parameter.
+ * 0-IPv4 DA 0 of 224.0.1.129. 1-IPv4 DA 1 of 224.0.0.107. 2-IPv6 DA 0 of
+ * 0xFF0*:0:0:0:0:0:0:181. 3-IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B. 4-UDP
+ * destination port 0 of 319. 5-UDP destination port 1 of 320. 6-MAC
+ * Ethertype 0 of 0x88F7. 7-configurable MAC Ethertype 1. 8-MAC DA 0 of
+ * 0x01-1B-19-00-00-00. 9-MAC DA 1 of 0x01-80-C2-00-00-0E. 10-configurable
+ * MAC DA 2. The reset default is set to mask out all parameters.
+ */
+#define NIG_REG_P0_TLLH_PTP_PARAM_MASK				 0x187f0
+/* [RW 14] Mask regiser for the rules used in detecting PTP packets. Set
+ * each bit to 1 to mask out that particular rule. 0-{IPv4 DA 0; UDP DP 0} .
+ * 1-{IPv4 DA 0; UDP DP 1} . 2-{IPv4 DA 1; UDP DP 0} . 3-{IPv4 DA 1; UDP DP
+ * 1} . 4-{IPv6 DA 0; UDP DP 0} . 5-{IPv6 DA 0; UDP DP 1} . 6-{IPv6 DA 1;
+ * UDP DP 0} . 7-{IPv6 DA 1; UDP DP 1} . 8-{MAC DA 0; Ethertype 0} . 9-{MAC
+ * DA 1; Ethertype 0} . 10-{MAC DA 0; Ethertype 1} . 11-{MAC DA 1; Ethertype
+ * 1} . 12-{MAC DA 2; Ethertype 0} . 13-{MAC DA 2; Ethertype 1} . The reset
+ * default is to mask out all of the rules.
+ */
+#define NIG_REG_P0_TLLH_PTP_RULE_MASK				 0x187f4
+/* [RW 19] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * TX side. Bits [15:0] reflect the sequence ID of the packet. Bit 16
+ * indicates the validity of the data in the buffer. Bit 17 indicates that
+ * the sequence ID is valid and it is waiting for the TX timestamp value.
+ * Bit 18 indicates whether the timestamp is from a SW request (value of 1)
+ * or HW request (value of 0). Writing a 1 to bit 16 will clear the buffer.
+ */
+#define NIG_REG_P1_TLLH_PTP_BUF_SEQID				 0x187ec
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * MCP. This location returns the lower 32 bits of timestamp value.
+ */
+#define NIG_REG_P1_TLLH_PTP_BUF_TS_LSB				 0x187e4
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * MCP. This location returns the upper 32 bits of timestamp value.
+ */
+#define NIG_REG_P1_TLLH_PTP_BUF_TS_MSB				 0x187e8
+/* [RW 11] Mask register for the various parameters used in determining PTP
+ * packet presence. Set each bit to 1 to mask out the particular parameter.
+ * 0-IPv4 DA 0 of 224.0.1.129. 1-IPv4 DA 1 of 224.0.0.107. 2-IPv6 DA 0 of
+ * 0xFF0*:0:0:0:0:0:0:181. 3-IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B. 4-UDP
+ * destination port 0 of 319. 5-UDP destination port 1 of 320. 6-MAC
+ * Ethertype 0 of 0x88F7. 7-configurable MAC Ethertype 1. 8-MAC DA 0 of
+ * 0x01-1B-19-00-00-00. 9-MAC DA 1 of 0x01-80-C2-00-00-0E. 10-configurable
+ * MAC DA 2. The reset default is set to mask out all parameters.
+ */
+#define NIG_REG_P1_TLLH_PTP_PARAM_MASK				 0x187f8
+/* [RW 14] Mask regiser for the rules used in detecting PTP packets. Set
+ * each bit to 1 to mask out that particular rule. 0-{IPv4 DA 0; UDP DP 0} .
+ * 1-{IPv4 DA 0; UDP DP 1} . 2-{IPv4 DA 1; UDP DP 0} . 3-{IPv4 DA 1; UDP DP
+ * 1} . 4-{IPv6 DA 0; UDP DP 0} . 5-{IPv6 DA 0; UDP DP 1} . 6-{IPv6 DA 1;
+ * UDP DP 0} . 7-{IPv6 DA 1; UDP DP 1} . 8-{MAC DA 0; Ethertype 0} . 9-{MAC
+ * DA 1; Ethertype 0} . 10-{MAC DA 0; Ethertype 1} . 11-{MAC DA 1; Ethertype
+ * 1} . 12-{MAC DA 2; Ethertype 0} . 13-{MAC DA 2; Ethertype 1} . The reset
+ * default is to mask out all of the rules.
+ */
+#define NIG_REG_P1_TLLH_PTP_RULE_MASK				 0x187fc
 /* [RW 32] Specify which of the credit registers the client is to be mapped
  * to. This register specifies bits 31:0 of the 36-bit value. Bits[3:0] are
  * for client 0; bits [35:32] are for client 8. For clients that are not
@@ -2513,6 +2685,10 @@
    swap is equal to SPIO pin that inputs from ifmux_serdes_swap. If 1 then
    ort swap is equal to ~nig_registers_port_swap.port_swap */
 #define NIG_REG_STRAP_OVERRIDE					 0x10398
+/* [WB 64] Addresses for TimeSync related registers in the timesync
+ * generator sub-module.
+ */
+#define NIG_REG_TIMESYNC_GEN_REG				 0x18800
 /* [RW 1] output enable for RX_XCM0 IF */
 #define NIG_REG_XCM0_OUT_EN					 0x100f0
 /* [RW 1] output enable for RX_XCM1 IF */

drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c

@@ -4725,6 +4725,12 @@ static void bnx2x_q_fill_update_data(struct bnx2x *bp,
 	data->tx_switching_change_flg =
 		test_bit(BNX2X_Q_UPDATE_TX_SWITCHING_CHNG,
 			 &params->update_flags);
+
+	/* PTP */
+	data->handle_ptp_pkts_flg =
+		test_bit(BNX2X_Q_UPDATE_PTP_PKTS, &params->update_flags);
+	data->handle_ptp_pkts_change_flg =
+		test_bit(BNX2X_Q_UPDATE_PTP_PKTS_CHNG, &params->update_flags);
 }
 
 static inline int bnx2x_q_send_update(struct bnx2x *bp,
@@ -5379,6 +5385,10 @@ static int bnx2x_func_chk_transition(struct bnx2x *bp,
 			 (!test_bit(BNX2X_F_CMD_STOP, &o->pending)))
 			next_state = BNX2X_F_STATE_STARTED;
 
+		else if ((cmd == BNX2X_F_CMD_SET_TIMESYNC) &&
+			 (!test_bit(BNX2X_F_CMD_STOP, &o->pending)))
+			next_state = BNX2X_F_STATE_STARTED;
+
 		else if (cmd == BNX2X_F_CMD_TX_STOP)
 			next_state = BNX2X_F_STATE_TX_STOPPED;
 
@@ -5388,6 +5398,10 @@ static int bnx2x_func_chk_transition(struct bnx2x *bp,
 		    (!test_bit(BNX2X_F_CMD_STOP, &o->pending)))
 			next_state = BNX2X_F_STATE_TX_STOPPED;
 
+		else if ((cmd == BNX2X_F_CMD_SET_TIMESYNC) &&
+			 (!test_bit(BNX2X_F_CMD_STOP, &o->pending)))
+			next_state = BNX2X_F_STATE_TX_STOPPED;
+
 		else if (cmd == BNX2X_F_CMD_TX_START)
 			next_state = BNX2X_F_STATE_STARTED;
 
@@ -5843,6 +5857,40 @@ static inline int bnx2x_func_send_tx_start(struct bnx2x *bp,
 			     U64_LO(data_mapping), NONE_CONNECTION_TYPE);
 }
 
+static inline
+int bnx2x_func_send_set_timesync(struct bnx2x *bp,
+				 struct bnx2x_func_state_params *params)
+{
+	struct bnx2x_func_sp_obj *o = params->f_obj;
+	struct set_timesync_ramrod_data *rdata =
+		(struct set_timesync_ramrod_data *)o->rdata;
+	dma_addr_t data_mapping = o->rdata_mapping;
+	struct bnx2x_func_set_timesync_params *set_timesync_params =
+		&params->params.set_timesync;
+
+	memset(rdata, 0, sizeof(*rdata));
+
+	/* Fill the ramrod data with provided parameters */
+	rdata->drift_adjust_cmd = set_timesync_params->drift_adjust_cmd;
+	rdata->offset_cmd = set_timesync_params->offset_cmd;
+	rdata->add_sub_drift_adjust_value =
+		set_timesync_params->add_sub_drift_adjust_value;
+	rdata->drift_adjust_value = set_timesync_params->drift_adjust_value;
+	rdata->drift_adjust_period = set_timesync_params->drift_adjust_period;
+	rdata->offset_delta.lo = U64_LO(set_timesync_params->offset_delta);
+	rdata->offset_delta.hi = U64_HI(set_timesync_params->offset_delta);
+
+	DP(BNX2X_MSG_SP, "Set timesync command params: drift_cmd = %d, offset_cmd = %d, add_sub_drift = %d, drift_val = %d, drift_period = %d, offset_lo = %d, offset_hi = %d\n",
+	   rdata->drift_adjust_cmd, rdata->offset_cmd,
+	   rdata->add_sub_drift_adjust_value, rdata->drift_adjust_value,
+	   rdata->drift_adjust_period, rdata->offset_delta.lo,
+	   rdata->offset_delta.hi);
+
+	return bnx2x_sp_post(bp, RAMROD_CMD_ID_COMMON_SET_TIMESYNC, 0,
+			     U64_HI(data_mapping),
+			     U64_LO(data_mapping), NONE_CONNECTION_TYPE);
+}
+
 static int bnx2x_func_send_cmd(struct bnx2x *bp,
 			       struct bnx2x_func_state_params *params)
 {
@@ -5865,6 +5913,8 @@ static int bnx2x_func_send_cmd(struct bnx2x *bp,
 		return bnx2x_func_send_tx_start(bp, params);
 	case BNX2X_F_CMD_SWITCH_UPDATE:
 		return bnx2x_func_send_switch_update(bp, params);
+	case BNX2X_F_CMD_SET_TIMESYNC:
+		return bnx2x_func_send_set_timesync(bp, params);
 	default:
 		BNX2X_ERR("Unknown command: %d\n", params->cmd);
 		return -EINVAL;

drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.h

@@ -770,7 +770,9 @@ enum {
 	BNX2X_Q_UPDATE_SILENT_VLAN_REM_CHNG,
 	BNX2X_Q_UPDATE_SILENT_VLAN_REM,
 	BNX2X_Q_UPDATE_TX_SWITCHING_CHNG,
-	BNX2X_Q_UPDATE_TX_SWITCHING
+	BNX2X_Q_UPDATE_TX_SWITCHING,
+	BNX2X_Q_UPDATE_PTP_PKTS_CHNG,
+	BNX2X_Q_UPDATE_PTP_PKTS,
 };
 
 /* Allowed Queue states */
@@ -853,6 +855,10 @@ enum bnx2x_q_type {
 #define BNX2X_MULTI_TX_COS			3 /* Maximum possible */
 
 #define MAC_PAD (ALIGN(ETH_ALEN, sizeof(u32)) - ETH_ALEN)
+/* DMAE channel to be used by FW for timesync workaroun. A driver that sends
+ * timesync-related ramrods must not use this DMAE command ID.
+ */
+#define FW_DMAE_CMD_ID 6
 
 struct bnx2x_queue_init_params {
 	struct {
@@ -1117,6 +1123,7 @@ enum bnx2x_func_cmd {
 	BNX2X_F_CMD_TX_STOP,
 	BNX2X_F_CMD_TX_START,
 	BNX2X_F_CMD_SWITCH_UPDATE,
+	BNX2X_F_CMD_SET_TIMESYNC,
 	BNX2X_F_CMD_MAX,
 };
 
@@ -1191,6 +1198,7 @@ struct bnx2x_func_afex_viflists_params {
 	u8 afex_vif_list_command;
 	u8 func_to_clear;
 };
+
 struct bnx2x_func_tx_start_params {
 	struct priority_cos traffic_type_to_priority_cos[MAX_TRAFFIC_TYPES];
 	u8 dcb_enabled;
@@ -1198,6 +1206,24 @@ struct bnx2x_func_tx_start_params {
 	u8 dont_add_pri_0_en;
 };
 
+struct bnx2x_func_set_timesync_params {
+	/* Reset, set or keep the current drift value */
+	u8 drift_adjust_cmd;
+
+	/* Dec, inc or keep the current offset */
+	u8 offset_cmd;
+
+	/* Drift value direction */
+	u8 add_sub_drift_adjust_value;
+
+	/* Drift, period and offset values to be used according to the commands
+	 * above.
+	 */
+	u8 drift_adjust_value;
+	u32 drift_adjust_period;
+	u64 offset_delta;
+};
+
 struct bnx2x_func_state_params {
 	struct bnx2x_func_sp_obj *f_obj;
 
@@ -1216,6 +1242,7 @@ struct bnx2x_func_state_params {
 		struct bnx2x_func_afex_update_params afex_update;
 		struct bnx2x_func_afex_viflists_params afex_viflists;
 		struct bnx2x_func_tx_start_params tx_start;
+		struct bnx2x_func_set_timesync_params set_timesync;
 	} params;
 };