diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
index 9683d4d3fced3da3cb01f53b48f991b0a2c5e4f6..241ffb28351c41689b0d2bbaf639141b3e4740fb 100644
--- a/drivers/mmc/core/core.c
+++ b/drivers/mmc/core/core.c
@@ -22,6 +22,7 @@
 #include <linux/scatterlist.h>
 #include <linux/log2.h>
 #include <linux/regulator/consumer.h>
+#include <linux/pm_runtime.h>
 
 #include <linux/mmc/card.h>
 #include <linux/mmc/host.h>
@@ -1785,6 +1786,18 @@ int mmc_resume_host(struct mmc_host *host)
 		if (!(host->pm_flags & MMC_PM_KEEP_POWER)) {
 			mmc_power_up(host);
 			mmc_select_voltage(host, host->ocr);
+			/*
+			 * Tell runtime PM core we just powered up the card,
+			 * since it still believes the card is powered off.
+			 * Note that currently runtime PM is only enabled
+			 * for SDIO cards that are MMC_CAP_POWER_OFF_CARD
+			 */
+			if (mmc_card_sdio(host->card) &&
+			    (host->caps & MMC_CAP_POWER_OFF_CARD)) {
+				pm_runtime_disable(&host->card->dev);
+				pm_runtime_set_active(&host->card->dev);
+				pm_runtime_enable(&host->card->dev);
+			}
 		}
 		BUG_ON(!host->bus_ops->resume);
 		err = host->bus_ops->resume(host);
diff --git a/drivers/mmc/core/sdio_bus.c b/drivers/mmc/core/sdio_bus.c
index 203da443e339a65b90e1ff47bc5240f9ba2ca07e..d29b9c36919a1d05fb8948d2f6231e366cb92c34 100644
--- a/drivers/mmc/core/sdio_bus.c
+++ b/drivers/mmc/core/sdio_bus.c
@@ -197,44 +197,12 @@ static int sdio_bus_remove(struct device *dev)
 
 #ifdef CONFIG_PM_RUNTIME
 
-static int sdio_bus_pm_prepare(struct device *dev)
-{
-	struct sdio_func *func = dev_to_sdio_func(dev);
-
-	/*
-	 * Resume an SDIO device which was suspended at run time at this
-	 * point, in order to allow standard SDIO suspend/resume paths
-	 * to keep working as usual.
-	 *
-	 * Ultimately, the SDIO driver itself will decide (in its
-	 * suspend handler, or lack thereof) whether the card should be
-	 * removed or kept, and if kept, at what power state.
-	 *
-	 * At this point, PM core have increased our use count, so it's
-	 * safe to directly resume the device. After system is resumed
-	 * again, PM core will drop back its runtime PM use count, and if
-	 * needed device will be suspended again.
-	 *
-	 * The end result is guaranteed to be a power state that is
-	 * coherent with the device's runtime PM use count.
-	 *
-	 * The return value of pm_runtime_resume is deliberately unchecked
-	 * since there is little point in failing system suspend if a
-	 * device can't be resumed.
-	 */
-	if (func->card->host->caps & MMC_CAP_POWER_OFF_CARD)
-		pm_runtime_resume(dev);
-
-	return 0;
-}
-
 static const struct dev_pm_ops sdio_bus_pm_ops = {
 	SET_RUNTIME_PM_OPS(
 		pm_generic_runtime_suspend,
 		pm_generic_runtime_resume,
 		pm_generic_runtime_idle
 	)
-	.prepare = sdio_bus_pm_prepare,
 };
 
 #define SDIO_PM_OPS_PTR	(&sdio_bus_pm_ops)