From db2d3260617ae8c9076ef12e6de06bd5b3d82cd3 Mon Sep 17 00:00:00 2001 From: Richard Henderson Date: Sun, 14 Jul 2013 09:55:08 -0700 Subject: [PATCH] alpha: Enable the rpcc clocksource for single processor Don't depend on SMP, just check the number of processors online. This allows a single distribution kernel to use the clocksource when run on a single processor machine. Do depend on whether or not we're using WTINT. Signed-off-by: Richard Henderson --- arch/alpha/kernel/time.c | 67 ++++++++++++++++++++++------------------ 1 file changed, 37 insertions(+), 30 deletions(-) diff --git a/arch/alpha/kernel/time.c b/arch/alpha/kernel/time.c index 4c6c0fe47a7b..0d72e2df4b0e 100644 --- a/arch/alpha/kernel/time.c +++ b/arch/alpha/kernel/time.c @@ -184,6 +184,37 @@ common_init_rtc(void) init_rtc_irq(); } + +#ifndef CONFIG_ALPHA_WTINT +/* + * The RPCC as a clocksource primitive. + * + * While we have free-running timecounters running on all CPUs, and we make + * a half-hearted attempt in init_rtc_rpcc_info to sync the timecounter + * with the wall clock, that initialization isn't kept up-to-date across + * different time counters in SMP mode. Therefore we can only use this + * method when there's only one CPU enabled. + * + * When using the WTINT PALcall, the RPCC may shift to a lower frequency, + * or stop altogether, while waiting for the interrupt. Therefore we cannot + * use this method when WTINT is in use. + */ + +static cycle_t read_rpcc(struct clocksource *cs) +{ + return rpcc(); +} + +static struct clocksource clocksource_rpcc = { + .name = "rpcc", + .rating = 300, + .read = read_rpcc, + .mask = CLOCKSOURCE_MASK(32), + .flags = CLOCK_SOURCE_IS_CONTINUOUS +}; +#endif /* ALPHA_WTINT */ + + /* Validate a computed cycle counter result against the known bounds for the given processor core. There's too much brokenness in the way of timing hardware for any one method to work everywhere. :-( @@ -294,33 +325,6 @@ rpcc_after_update_in_progress(void) return rpcc(); } -#ifndef CONFIG_SMP -/* Until and unless we figure out how to get cpu cycle counters - in sync and keep them there, we can't use the rpcc. */ -static cycle_t read_rpcc(struct clocksource *cs) -{ - cycle_t ret = (cycle_t)rpcc(); - return ret; -} - -static struct clocksource clocksource_rpcc = { - .name = "rpcc", - .rating = 300, - .read = read_rpcc, - .mask = CLOCKSOURCE_MASK(32), - .flags = CLOCK_SOURCE_IS_CONTINUOUS -}; - -static inline void register_rpcc_clocksource(long cycle_freq) -{ - clocksource_register_hz(&clocksource_rpcc, cycle_freq); -} -#else /* !CONFIG_SMP */ -static inline void register_rpcc_clocksource(long cycle_freq) -{ -} -#endif /* !CONFIG_SMP */ - void __init time_init(void) { @@ -362,20 +366,23 @@ time_init(void) "and unable to estimate a proper value!\n"); } + /* See above for restrictions on using clocksource_rpcc. */ +#ifndef CONFIG_ALPHA_WTINT + if (hwrpb->nr_processors == 1) + clocksource_register_hz(&clocksource_rpcc, cycle_freq); +#endif + /* From John Bowman : allow the values to settle, as the Update-In-Progress bit going low isn't good enough on some hardware. 2ms is our guess; we haven't found bogomips yet, but this is close on a 500Mhz box. */ __delay(1000000); - if (HZ > (1<<16)) { extern void __you_loose (void); __you_loose(); } - register_rpcc_clocksource(cycle_freq); - state.last_time = cc1; state.scaled_ticks_per_cycle = ((unsigned long) HZ << FIX_SHIFT) / cycle_freq; -- GitLab