diff --git a/Documentation/xtensa/mmu.txt b/Documentation/xtensa/mmu.txt index 0312fe66475c2a8c985e86aa3250ee82b0fc8496..222a2c6748e63636e6caf5685acee4b74357be7e 100644 --- a/Documentation/xtensa/mmu.txt +++ b/Documentation/xtensa/mmu.txt @@ -3,15 +3,8 @@ MMUv3 initialization sequence. The code in the initialize_mmu macro sets up MMUv3 memory mapping identically to MMUv2 fixed memory mapping. Depending on CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX symbol this code is -located in one of the following address ranges: - - 0xF0000000..0xFFFFFFFF (will keep same address in MMU v2 layout; - typically ROM) - 0x00000000..0x07FFFFFF (system RAM; this code is actually linked - at 0xD0000000..0xD7FFFFFF [cached] - or 0xD8000000..0xDFFFFFFF [uncached]; - in any case, initially runs elsewhere - than linked, so have to be careful) +located in addresses it was linked for (symbol undefined), or not +(symbol defined), so it needs to be position-independent. The code has the following assumptions: This code fragment is run only on an MMU v3. @@ -28,24 +21,26 @@ TLB setup proceeds along the following steps. PA = physical address (two upper nibbles of it); pc = physical range that contains this code; -After step 2, we jump to virtual address in 0x40000000..0x5fffffff -that corresponds to next instruction to execute in this code. -After step 4, we jump to intended (linked) address of this code. - - Step 0 Step1 Step 2 Step3 Step 4 Step5 - ============ ===== ============ ===== ============ ===== - VA PA PA VA PA PA VA PA PA - ------ -- -- ------ -- -- ------ -- -- - E0..FF -> E0 -> E0 E0..FF -> E0 F0..FF -> F0 -> F0 - C0..DF -> C0 -> C0 C0..DF -> C0 E0..EF -> F0 -> F0 - A0..BF -> A0 -> A0 A0..BF -> A0 D8..DF -> 00 -> 00 - 80..9F -> 80 -> 80 80..9F -> 80 D0..D7 -> 00 -> 00 - 60..7F -> 60 -> 60 60..7F -> 60 - 40..5F -> 40 40..5F -> pc -> pc 40..5F -> pc - 20..3F -> 20 -> 20 20..3F -> 20 - 00..1F -> 00 -> 00 00..1F -> 00 - -The default location of IO peripherals is above 0xf0000000. This may change +After step 2, we jump to virtual address in the range 0x40000000..0x5fffffff +or 0x00000000..0x1fffffff, depending on whether the kernel was loaded below +0x40000000 or above. That address corresponds to next instruction to execute +in this code. After step 4, we jump to intended (linked) address of this code. +The scheme below assumes that the kernel is loaded below 0x40000000. + + Step0 Step1 Step2 Step3 Step4 Step5 + ===== ===== ===== ===== ===== ===== + VA PA PA PA PA VA PA PA + ------ -- -- -- -- ------ -- -- + E0..FF -> E0 -> E0 -> E0 F0..FF -> F0 -> F0 + C0..DF -> C0 -> C0 -> C0 E0..EF -> F0 -> F0 + A0..BF -> A0 -> A0 -> A0 D8..DF -> 00 -> 00 + 80..9F -> 80 -> 80 -> 80 D0..D7 -> 00 -> 00 + 60..7F -> 60 -> 60 -> 60 + 40..5F -> 40 -> pc -> pc 40..5F -> pc + 20..3F -> 20 -> 20 -> 20 + 00..1F -> 00 -> 00 -> 00 + +The default location of IO peripherals is above 0xf0000000. This may be changed using a "ranges" property in a device tree simple-bus node. See ePAPR 1.1, ยง6.5 for details on the syntax and semantic of simple-bus nodes. The following limitations apply: @@ -62,3 +57,127 @@ limitations apply: 6. The IO area covers the entire 256MB segment of parent-bus-address; the "ranges" triplet length field is ignored + + +MMUv3 address space layouts. +============================ + +Default MMUv2-compatible layout. + + Symbol VADDR Size ++------------------+ +| Userspace | 0x00000000 TASK_SIZE ++------------------+ 0x40000000 ++------------------+ +| Page table | 0x80000000 ++------------------+ 0x80400000 ++------------------+ +| KMAP area | PKMAP_BASE PTRS_PER_PTE * +| | DCACHE_N_COLORS * +| | PAGE_SIZE +| | (4MB * DCACHE_N_COLORS) ++------------------+ +| Atomic KMAP area | FIXADDR_START KM_TYPE_NR * +| | NR_CPUS * +| | DCACHE_N_COLORS * +| | PAGE_SIZE ++------------------+ FIXADDR_TOP 0xbffff000 ++------------------+ +| VMALLOC area | VMALLOC_START 0xc0000000 128MB - 64KB ++------------------+ VMALLOC_END +| Cache aliasing | TLBTEMP_BASE_1 0xc7ff0000 DCACHE_WAY_SIZE +| remap area 1 | ++------------------+ +| Cache aliasing | TLBTEMP_BASE_2 DCACHE_WAY_SIZE +| remap area 2 | ++------------------+ ++------------------+ +| Cached KSEG | XCHAL_KSEG_CACHED_VADDR 0xd0000000 128MB ++------------------+ +| Uncached KSEG | XCHAL_KSEG_BYPASS_VADDR 0xd8000000 128MB ++------------------+ +| Cached KIO | XCHAL_KIO_CACHED_VADDR 0xe0000000 256MB ++------------------+ +| Uncached KIO | XCHAL_KIO_BYPASS_VADDR 0xf0000000 256MB ++------------------+ + + +256MB cached + 256MB uncached layout. + + Symbol VADDR Size ++------------------+ +| Userspace | 0x00000000 TASK_SIZE ++------------------+ 0x40000000 ++------------------+ +| Page table | 0x80000000 ++------------------+ 0x80400000 ++------------------+ +| KMAP area | PKMAP_BASE PTRS_PER_PTE * +| | DCACHE_N_COLORS * +| | PAGE_SIZE +| | (4MB * DCACHE_N_COLORS) ++------------------+ +| Atomic KMAP area | FIXADDR_START KM_TYPE_NR * +| | NR_CPUS * +| | DCACHE_N_COLORS * +| | PAGE_SIZE ++------------------+ FIXADDR_TOP 0x9ffff000 ++------------------+ +| VMALLOC area | VMALLOC_START 0xa0000000 128MB - 64KB ++------------------+ VMALLOC_END +| Cache aliasing | TLBTEMP_BASE_1 0xa7ff0000 DCACHE_WAY_SIZE +| remap area 1 | ++------------------+ +| Cache aliasing | TLBTEMP_BASE_2 DCACHE_WAY_SIZE +| remap area 2 | ++------------------+ ++------------------+ +| Cached KSEG | XCHAL_KSEG_CACHED_VADDR 0xb0000000 256MB ++------------------+ +| Uncached KSEG | XCHAL_KSEG_BYPASS_VADDR 0xc0000000 256MB ++------------------+ ++------------------+ +| Cached KIO | XCHAL_KIO_CACHED_VADDR 0xe0000000 256MB ++------------------+ +| Uncached KIO | XCHAL_KIO_BYPASS_VADDR 0xf0000000 256MB ++------------------+ + + +512MB cached + 512MB uncached layout. + + Symbol VADDR Size ++------------------+ +| Userspace | 0x00000000 TASK_SIZE ++------------------+ 0x40000000 ++------------------+ +| Page table | 0x80000000 ++------------------+ 0x80400000 ++------------------+ +| KMAP area | PKMAP_BASE PTRS_PER_PTE * +| | DCACHE_N_COLORS * +| | PAGE_SIZE +| | (4MB * DCACHE_N_COLORS) ++------------------+ +| Atomic KMAP area | FIXADDR_START KM_TYPE_NR * +| | NR_CPUS * +| | DCACHE_N_COLORS * +| | PAGE_SIZE ++------------------+ FIXADDR_TOP 0x8ffff000 ++------------------+ +| VMALLOC area | VMALLOC_START 0x90000000 128MB - 64KB ++------------------+ VMALLOC_END +| Cache aliasing | TLBTEMP_BASE_1 0x97ff0000 DCACHE_WAY_SIZE +| remap area 1 | ++------------------+ +| Cache aliasing | TLBTEMP_BASE_2 DCACHE_WAY_SIZE +| remap area 2 | ++------------------+ ++------------------+ +| Cached KSEG | XCHAL_KSEG_CACHED_VADDR 0xa0000000 512MB ++------------------+ +| Uncached KSEG | XCHAL_KSEG_BYPASS_VADDR 0xc0000000 512MB ++------------------+ +| Cached KIO | XCHAL_KIO_CACHED_VADDR 0xe0000000 256MB ++------------------+ +| Uncached KIO | XCHAL_KIO_BYPASS_VADDR 0xf0000000 256MB ++------------------+ diff --git a/arch/xtensa/Kconfig b/arch/xtensa/Kconfig index 64336f666fb61ac0cd97b1e7afc92dda343d65fe..f61058617ada462c6e571c7936c3ebf92621aa26 100644 --- a/arch/xtensa/Kconfig +++ b/arch/xtensa/Kconfig @@ -13,16 +13,19 @@ config XTENSA select GENERIC_IRQ_SHOW select GENERIC_PCI_IOMAP select GENERIC_SCHED_CLOCK + select HAVE_DEBUG_KMEMLEAK select HAVE_DMA_API_DEBUG select HAVE_EXIT_THREAD select HAVE_FUNCTION_TRACER select HAVE_FUTEX_CMPXCHG if !MMU select HAVE_HW_BREAKPOINT if PERF_EVENTS select HAVE_IRQ_TIME_ACCOUNTING + select HAVE_MEMBLOCK select HAVE_OPROFILE select HAVE_PERF_EVENTS select IRQ_DOMAIN select MODULES_USE_ELF_RELA + select NO_BOOTMEM select PERF_USE_VMALLOC select VIRT_TO_BUS help @@ -209,7 +212,8 @@ config HOTPLUG_CPU config INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX bool "Initialize Xtensa MMU inside the Linux kernel code" - default y + depends on !XTENSA_VARIANT_FSF && !XTENSA_VARIANT_DC232B + default y if XTENSA_VARIANT_DC233C || XTENSA_VARIANT_CUSTOM help Earlier version initialized the MMU in the exception vector before jumping to _startup in head.S and had an advantage that @@ -236,6 +240,71 @@ config INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX If in doubt, say Y. +config KSEG_PADDR + hex "Physical address of the KSEG mapping" + depends on INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX && MMU + default 0x00000000 + help + This is the physical address where KSEG is mapped. Please refer to + the chosen KSEG layout help for the required address alignment. + Unpacked kernel image (including vectors) must be located completely + within KSEG. + Physical memory below this address is not available to linux. + + If unsure, leave the default value here. + +config KERNEL_LOAD_ADDRESS + hex "Kernel load address" + default 0x60003000 if !MMU + default 0x00003000 if MMU && INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX + default 0xd0003000 if MMU && !INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX + help + This is the address where the kernel is loaded. + It is virtual address for MMUv2 configurations and physical address + for all other configurations. + + If unsure, leave the default value here. + +config VECTORS_OFFSET + hex "Kernel vectors offset" + default 0x00003000 + help + This is the offset of the kernel image from the relocatable vectors + base. + + If unsure, leave the default value here. + +choice + prompt "KSEG layout" + depends on MMU + default XTENSA_KSEG_MMU_V2 + +config XTENSA_KSEG_MMU_V2 + bool "MMUv2: 128MB cached + 128MB uncached" + help + MMUv2 compatible kernel memory map: TLB way 5 maps 128MB starting + at KSEG_PADDR to 0xd0000000 with cache and to 0xd8000000 + without cache. + KSEG_PADDR must be aligned to 128MB. + +config XTENSA_KSEG_256M + bool "256MB cached + 256MB uncached" + depends on INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX + help + TLB way 6 maps 256MB starting at KSEG_PADDR to 0xb0000000 + with cache and to 0xc0000000 without cache. + KSEG_PADDR must be aligned to 256MB. + +config XTENSA_KSEG_512M + bool "512MB cached + 512MB uncached" + depends on INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX + help + TLB way 6 maps 512MB starting at KSEG_PADDR to 0xa0000000 + with cache and to 0xc0000000 without cache. + KSEG_PADDR must be aligned to 256MB. + +endchoice + config HIGHMEM bool "High Memory Support" depends on MMU @@ -331,7 +400,7 @@ config XTENSA_PLATFORM_XT2000 config XTENSA_PLATFORM_XTFPGA bool "XTFPGA" select ETHOC if ETHERNET - select PLATFORM_WANT_DEFAULT_MEM + select PLATFORM_WANT_DEFAULT_MEM if !MMU select SERIAL_CONSOLE select XTENSA_CALIBRATE_CCOUNT help @@ -369,6 +438,7 @@ config USE_OF bool "Flattened Device Tree support" select OF select OF_EARLY_FLATTREE + select OF_RESERVED_MEM help Include support for flattened device tree machine descriptions. @@ -439,16 +509,9 @@ config DEFAULT_MEM_START default 0x00000000 if MMU default 0x60000000 if !MMU help - This is a fallback start address of the default memory area, it is - used when no physical memory size is passed through DTB or through - boot parameter from bootloader. - - In noMMU configuration the following parameters are derived from it: - - kernel load address; - - kernel entry point address; - - relocatable vectors base address; - - uBoot load address; - - TASK_SIZE. + This is the base address of the default memory area. + Default memory area has platform-specific meaning, it may be used + for e.g. early cache initialization. If unsure, leave the default value here. @@ -457,11 +520,9 @@ config DEFAULT_MEM_SIZE depends on PLATFORM_WANT_DEFAULT_MEM default 0x04000000 help - This is a fallback size of the default memory area, it is used when - no physical memory size is passed through DTB or through boot - parameter from bootloader. - - It's also used for TASK_SIZE calculation in noMMU configuration. + This is the size of the default memory area. + Default memory area has platform-specific meaning, it may be used + for e.g. early cache initialization. If unsure, leave the default value here. diff --git a/arch/xtensa/boot/boot-elf/boot.lds.S b/arch/xtensa/boot/boot-elf/boot.lds.S index e54f2c9df63aa725e6777ea83558b2372c0144a4..a30993054e9cc6c5b1e131357a2b833b01ba7284 100644 --- a/arch/xtensa/boot/boot-elf/boot.lds.S +++ b/arch/xtensa/boot/boot-elf/boot.lds.S @@ -23,7 +23,7 @@ SECTIONS *(.ResetVector.text) } - .image KERNELOFFSET: AT (LOAD_MEMORY_ADDRESS) + .image KERNELOFFSET: AT (CONFIG_KERNEL_LOAD_ADDRESS) { _image_start = .; *(image) diff --git a/arch/xtensa/boot/boot-elf/bootstrap.S b/arch/xtensa/boot/boot-elf/bootstrap.S index e6bf313613cf6ddcfa5682b9b8665433969460d9..b6aa85328ac0ccc05936bcf9b477499e7bbbbfe7 100644 --- a/arch/xtensa/boot/boot-elf/bootstrap.S +++ b/arch/xtensa/boot/boot-elf/bootstrap.S @@ -35,7 +35,12 @@ _ResetVector: .align 4 RomInitAddr: - .word LOAD_MEMORY_ADDRESS +#if defined(CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX) && \ + XCHAL_HAVE_PTP_MMU && XCHAL_HAVE_SPANNING_WAY + .word CONFIG_KERNEL_LOAD_ADDRESS +#else + .word KERNELOFFSET +#endif RomBootParam: .word _bootparam _bootparam: diff --git a/arch/xtensa/boot/boot-uboot/Makefile b/arch/xtensa/boot/boot-uboot/Makefile index 403fcf23405cf27bbd5bcdcad1d0a7c74269cbbd..0f4c417b4196e9c71ee3d64e63575866145a4243 100644 --- a/arch/xtensa/boot/boot-uboot/Makefile +++ b/arch/xtensa/boot/boot-uboot/Makefile @@ -4,15 +4,7 @@ # for more details. # -ifdef CONFIG_MMU -ifdef CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX -UIMAGE_LOADADDR = 0x00003000 -else -UIMAGE_LOADADDR = 0xd0003000 -endif -else -UIMAGE_LOADADDR = $(shell printf "0x%x" $$(( ${CONFIG_DEFAULT_MEM_START} + 0x3000 )) ) -endif +UIMAGE_LOADADDR = $(CONFIG_KERNEL_LOAD_ADDRESS) UIMAGE_COMPRESSION = gzip $(obj)/../uImage: vmlinux.bin.gz FORCE diff --git a/arch/xtensa/boot/dts/csp.dts b/arch/xtensa/boot/dts/csp.dts new file mode 100644 index 0000000000000000000000000000000000000000..4082f26716b9a56768946568b267c04bf7f00764 --- /dev/null +++ b/arch/xtensa/boot/dts/csp.dts @@ -0,0 +1,54 @@ +/dts-v1/; + +/ { + compatible = "cdns,xtensa-xtfpga"; + #address-cells = <1>; + #size-cells = <1>; + interrupt-parent = <&pic>; + + chosen { + bootargs = "earlycon=cdns,0xfd000000,115200 console=tty0 console=ttyPS0,115200 root=/dev/ram0 rw earlyprintk xilinx_uartps.rx_trigger_level=32 loglevel=8 nohz=off ignore_loglevel"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x40000000>; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + cpu@0 { + compatible = "cdns,xtensa-cpu"; + reg = <0>; + }; + }; + + pic: pic { + compatible = "cdns,xtensa-pic"; + #interrupt-cells = <2>; + interrupt-controller; + }; + + clocks { + osc: main-oscillator { + #clock-cells = <0>; + compatible = "fixed-clock"; + }; + }; + + soc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges = <0x00000000 0xf0000000 0x10000000>; + + uart0: serial@0d000000 { + compatible = "xlnx,xuartps", "cdns,uart-r1p8"; + clocks = <&osc>, <&osc>; + clock-names = "uart_clk", "pclk"; + reg = <0x0d000000 0x1000>; + interrupts = <0 1>; + }; + }; +}; diff --git a/arch/xtensa/boot/dts/xtfpga.dtsi b/arch/xtensa/boot/dts/xtfpga.dtsi index cd45f9c2c4484225960dc63267230bb3c7f5a2eb..91616a9d79dfbbc5bd181e85b4a78a8cbce3f3a9 100644 --- a/arch/xtensa/boot/dts/xtfpga.dtsi +++ b/arch/xtensa/boot/dts/xtfpga.dtsi @@ -19,9 +19,7 @@ cpu@0 { compatible = "cdns,xtensa-cpu"; reg = <0>; - /* Filled in by platform_setup from FPGA register - * clock-frequency = <100000000>; - */ + clocks = <&osc>; }; }; @@ -36,11 +34,6 @@ }; clocks { - osc: main-oscillator { - #clock-cells = <0>; - compatible = "fixed-clock"; - }; - clk54: clk54 { #clock-cells = <0>; compatible = "fixed-clock"; @@ -54,6 +47,12 @@ compatible = "simple-bus"; ranges = <0x00000000 0xf0000000 0x10000000>; + osc: main-oscillator { + #clock-cells = <0>; + compatible = "cdns,xtfpga-clock"; + reg = <0x0d020004 0x4>; + }; + serial0: serial@0d050020 { device_type = "serial"; compatible = "ns16550a"; diff --git a/arch/xtensa/configs/audio_kc705_defconfig b/arch/xtensa/configs/audio_kc705_defconfig index c4904db1558261b10eba6cf0ebc0d3d3a600ed96..8d16925765cb01c613ce3b552cad41ea818f0f52 100644 --- a/arch/xtensa/configs/audio_kc705_defconfig +++ b/arch/xtensa/configs/audio_kc705_defconfig @@ -33,7 +33,7 @@ CONFIG_HIGHMEM=y # CONFIG_PCI is not set CONFIG_XTENSA_PLATFORM_XTFPGA=y CONFIG_CMDLINE_BOOL=y -CONFIG_CMDLINE="earlycon=uart8250,mmio32,0xfd050020,115200n8 console=ttyS0,115200n8 ip=dhcp root=/dev/nfs rw debug" +CONFIG_CMDLINE="earlycon=uart8250,mmio32native,0xfd050020,115200n8 console=ttyS0,115200n8 ip=dhcp root=/dev/nfs rw debug memmap=0x38000000@0" CONFIG_USE_OF=y CONFIG_BUILTIN_DTB="kc705" # CONFIG_COMPACTION is not set diff --git a/arch/xtensa/configs/cadence_csp_defconfig b/arch/xtensa/configs/cadence_csp_defconfig new file mode 100644 index 0000000000000000000000000000000000000000..f2d3094aa1d1308ca89ee56e6c06891fd5999fd5 --- /dev/null +++ b/arch/xtensa/configs/cadence_csp_defconfig @@ -0,0 +1,122 @@ +CONFIG_SYSVIPC=y +CONFIG_POSIX_MQUEUE=y +CONFIG_USELIB=y +CONFIG_IRQ_DOMAIN_DEBUG=y +CONFIG_NO_HZ_IDLE=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_IRQ_TIME_ACCOUNTING=y +CONFIG_BSD_PROCESS_ACCT=y +CONFIG_CGROUP_FREEZER=y +CONFIG_CPUSETS=y +CONFIG_CGROUP_DEVICE=y +CONFIG_CGROUP_CPUACCT=y +CONFIG_CGROUP_DEBUG=y +CONFIG_NAMESPACES=y +CONFIG_SCHED_AUTOGROUP=y +CONFIG_RELAY=y +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="$$KERNEL_INITRAMFS_SOURCE" +# CONFIG_RD_BZIP2 is not set +# CONFIG_RD_LZMA is not set +# CONFIG_RD_XZ is not set +# CONFIG_RD_LZO is not set +# CONFIG_RD_LZ4 is not set +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_EMBEDDED=y +CONFIG_PROFILING=y +CONFIG_MODULES=y +CONFIG_MODULE_FORCE_LOAD=y +CONFIG_MODULE_UNLOAD=y +CONFIG_MODULE_FORCE_UNLOAD=y +# CONFIG_IOSCHED_DEADLINE is not set +# CONFIG_IOSCHED_CFQ is not set +CONFIG_XTENSA_VARIANT_CUSTOM=y +CONFIG_XTENSA_VARIANT_CUSTOM_NAME="csp" +CONFIG_XTENSA_UNALIGNED_USER=y +CONFIG_PREEMPT=y +CONFIG_HIGHMEM=y +# CONFIG_PCI is not set +CONFIG_XTENSA_PLATFORM_XTFPGA=y +CONFIG_USE_OF=y +CONFIG_BUILTIN_DTB="csp" +# CONFIG_COMPACTION is not set +CONFIG_XTFPGA_LCD=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_NET=y +CONFIG_PACKET=y +CONFIG_UNIX=y +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y +# CONFIG_INET_XFRM_MODE_TRANSPORT is not set +# CONFIG_INET_XFRM_MODE_TUNNEL is not set +# CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_DIAG is not set +# CONFIG_IPV6 is not set +# CONFIG_WIRELESS is not set +CONFIG_DEVTMPFS=y +CONFIG_DEVTMPFS_MOUNT=y +# CONFIG_STANDALONE is not set +# CONFIG_FW_LOADER is not set +CONFIG_MTD=y +CONFIG_MTD_CFI=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_CFI_INTELEXT=y +CONFIG_MTD_CFI_AMDSTD=y +CONFIG_MTD_CFI_STAA=y +CONFIG_MTD_PHYSMAP_OF=y +CONFIG_MTD_UBI=y +CONFIG_BLK_DEV_LOOP=y +CONFIG_BLK_DEV_RAM=y +CONFIG_SCSI=y +CONFIG_BLK_DEV_SD=y +# CONFIG_INPUT_MOUSEDEV is not set +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +CONFIG_LEGACY_PTY_COUNT=16 +CONFIG_SERIAL_XILINX_PS_UART=y +CONFIG_SERIAL_XILINX_PS_UART_CONSOLE=y +CONFIG_HW_RANDOM=y +# CONFIG_HWMON is not set +CONFIG_WATCHDOG=y +CONFIG_WATCHDOG_NOWAYOUT=y +CONFIG_SOFT_WATCHDOG=y +# CONFIG_VGA_CONSOLE is not set +# CONFIG_USB_SUPPORT is not set +# CONFIG_IOMMU_SUPPORT is not set +CONFIG_EXT3_FS=y +CONFIG_FANOTIFY=y +CONFIG_VFAT_FS=y +CONFIG_PROC_KCORE=y +CONFIG_TMPFS=y +CONFIG_TMPFS_POSIX_ACL=y +# CONFIG_MISC_FILESYSTEMS is not set +CONFIG_NFS_FS=y +CONFIG_NFS_V4=y +CONFIG_NFS_SWAP=y +CONFIG_ROOT_NFS=y +CONFIG_SUNRPC_DEBUG=y +CONFIG_NLS_CODEPAGE_437=y +CONFIG_NLS_ISO8859_1=y +CONFIG_PRINTK_TIME=y +CONFIG_DYNAMIC_DEBUG=y +CONFIG_DEBUG_INFO=y +CONFIG_MAGIC_SYSRQ=y +CONFIG_LOCKUP_DETECTOR=y +# CONFIG_SCHED_DEBUG is not set +CONFIG_SCHEDSTATS=y +CONFIG_TIMER_STATS=y +CONFIG_DEBUG_RT_MUTEXES=y +CONFIG_PROVE_LOCKING=y +CONFIG_DEBUG_ATOMIC_SLEEP=y +CONFIG_RCU_TRACE=y +CONFIG_FUNCTION_TRACER=y +# CONFIG_S32C1I_SELFTEST is not set +# CONFIG_CRYPTO_ECHAINIV is not set +CONFIG_CRYPTO_DEFLATE=y +CONFIG_CRYPTO_LZO=y +# CONFIG_CRYPTO_HW is not set diff --git a/arch/xtensa/configs/common_defconfig b/arch/xtensa/configs/common_defconfig index 721df1214bc3bff9026f5f593a7453b2a8341a68..4bcc76b02109637bc0f29241a9a029ce835e6504 100644 --- a/arch/xtensa/configs/common_defconfig +++ b/arch/xtensa/configs/common_defconfig @@ -1,204 +1,15 @@ -# -# Automatically generated make config: don't edit -# Linux kernel version: 2.6.11-rc2 -# Tue Mar 1 16:36:53 2005 -# -# CONFIG_FRAME_POINTER is not set -CONFIG_XTENSA=y -# CONFIG_UID16 is not set -CONFIG_RWSEM_XCHGADD_ALGORITHM=y -CONFIG_HAVE_DEC_LOCK=y - -# -# Code maturity level options -# -CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y -CONFIG_BROKEN_ON_SMP=y - -# -# General setup -# -CONFIG_LOCALVERSION="" -CONFIG_SWAP=y CONFIG_SYSVIPC=y -# CONFIG_POSIX_MQUEUE is not set CONFIG_BSD_PROCESS_ACCT=y -# CONFIG_BSD_PROCESS_ACCT_V3 is not set -CONFIG_SYSCTL=y -# CONFIG_AUDIT is not set CONFIG_LOG_BUF_SHIFT=14 -# CONFIG_HOTPLUG is not set -CONFIG_KOBJECT_UEVENT=y -# CONFIG_IKCONFIG is not set -# CONFIG_EXPERT is not set -CONFIG_KALLSYMS=y -# CONFIG_KALLSYMS_ALL is not set -# CONFIG_KALLSYMS_EXTRA_PASS is not set -CONFIG_FUTEX=y -CONFIG_EPOLL=y -# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set -CONFIG_SHMEM=y -CONFIG_CC_ALIGN_FUNCTIONS=0 -CONFIG_CC_ALIGN_LABELS=0 -CONFIG_CC_ALIGN_LOOPS=0 -CONFIG_CC_ALIGN_JUMPS=0 -# CONFIG_TINY_SHMEM is not set - -# -# Loadable module support -# CONFIG_MODULES=y -# CONFIG_MODULE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y CONFIG_MODVERSIONS=y -# CONFIG_MODULE_SRCVERSION_ALL is not set -CONFIG_KMOD=y - -# -# Processor type and features -# -CONFIG_XTENSA_ARCH_LINUX_BE=y -# CONFIG_XTENSA_ARCH_LINUX_LE is not set -# CONFIG_XTENSA_ARCH_LINUX_TEST is not set -# CONFIG_XTENSA_ARCH_S5 is not set -# CONFIG_XTENSA_CUSTOM is not set -CONFIG_MMU=y -# CONFIG_XTENSA_UNALIGNED_USER is not set -# CONFIG_PREEMPT is not set -# CONFIG_HIGHMEM is not set - -# -# Platform options -# -# CONFIG_XTENSA_PLATFORM_ISS is not set CONFIG_XTENSA_PLATFORM_XT2000=y -CONFIG_XTENSA_CALIBRATE_CCOUNT=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_CMDLINE_BOOL=y -CONFIG_CMDLINE="console=ttyS0,38400 ip=bootp root=nfs nfsroot=/opt/montavista/pro/devkit/xtensa/linux_be/target" - -# -# Bus options -# -CONFIG_PCI=y -# CONFIG_PCI_LEGACY_PROC is not set -# CONFIG_PCI_NAMES is not set - -# -# PCCARD (PCMCIA/CardBus) support -# -# CONFIG_PCCARD is not set - -# -# PC-card bridges -# - -# -# PCI Hotplug Support -# -# CONFIG_HOTPLUG_PCI is not set - -# -# Exectuable file formats -# -CONFIG_KCORE_ELF=y -CONFIG_BINFMT_ELF=y +CONFIG_CMDLINE="console=ttyS0,38400 ip=bootp root=nfs nfsroot=/opt/montavista/pro/devkit/xtensa/linux_be/target memmap=128M@0" CONFIG_BINFMT_MISC=y - -# -# Device Drivers -# - -# -# Generic Driver Options -# -CONFIG_STANDALONE=y -CONFIG_PREVENT_FIRMWARE_BUILD=y -# CONFIG_FW_LOADER is not set -# CONFIG_DEBUG_DRIVER is not set - -# -# Memory Technology Devices (MTD) -# -# CONFIG_MTD is not set - -# -# Parallel port support -# -# CONFIG_PARPORT is not set - -# -# Plug and Play support -# - -# -# Block devices -# -# CONFIG_BLK_DEV_FD is not set -# CONFIG_BLK_CPQ_DA is not set -# CONFIG_BLK_CPQ_CISS_DA is not set -# CONFIG_BLK_DEV_DAC960 is not set -# CONFIG_BLK_DEV_UMEM is not set -# CONFIG_BLK_DEV_COW_COMMON is not set -# CONFIG_BLK_DEV_LOOP is not set -# CONFIG_BLK_DEV_NBD is not set -# CONFIG_BLK_DEV_SX8 is not set -# CONFIG_BLK_DEV_RAM is not set -CONFIG_BLK_DEV_RAM_COUNT=16 -CONFIG_INITRAMFS_SOURCE="" -# CONFIG_CDROM_PKTCDVD is not set - -# -# IO Schedulers -# -CONFIG_IOSCHED_NOOP=y -CONFIG_IOSCHED_AS=y -CONFIG_IOSCHED_DEADLINE=y -CONFIG_IOSCHED_CFQ=y -# CONFIG_ATA_OVER_ETH is not set - -# -# ATA/ATAPI/MFM/RLL support -# -# CONFIG_IDE is not set - -# -# SCSI device support -# -# CONFIG_SCSI is not set - -# -# Multi-device support (RAID and LVM) -# -# CONFIG_MD is not set - -# -# Fusion MPT device support -# - -# -# IEEE 1394 (FireWire) support -# -# CONFIG_IEEE1394 is not set - -# -# I2O device support -# -# CONFIG_I2O is not set - -# -# Networking support -# CONFIG_NET=y - -# -# Networking options -# -# CONFIG_PACKET is not set -# CONFIG_NETLINK_DEV is not set CONFIG_UNIX=y -# CONFIG_NET_KEY is not set CONFIG_INET=y CONFIG_IP_MULTICAST=y CONFIG_IP_ADVANCED_ROUTER=y @@ -209,47 +20,10 @@ CONFIG_IP_PNP=y CONFIG_IP_PNP_DHCP=y CONFIG_IP_PNP_BOOTP=y CONFIG_IP_PNP_RARP=y -# CONFIG_NET_IPIP is not set -# CONFIG_NET_IPGRE is not set -# CONFIG_IP_MROUTE is not set -# CONFIG_ARPD is not set -# CONFIG_SYN_COOKIES is not set -# CONFIG_INET_AH is not set -# CONFIG_INET_ESP is not set -# CONFIG_INET_IPCOMP is not set -# CONFIG_INET_TUNNEL is not set -# CONFIG_IP_TCPDIAG is not set -# CONFIG_IP_TCPDIAG_IPV6 is not set # CONFIG_IPV6 is not set -# CONFIG_NETFILTER is not set - -# -# SCTP Configuration (EXPERIMENTAL) -# -# CONFIG_IP_SCTP is not set -# CONFIG_ATM is not set -# CONFIG_BRIDGE is not set -# CONFIG_VLAN_8021Q is not set -# CONFIG_DECNET is not set -# CONFIG_LLC2 is not set -# CONFIG_IPX is not set -# CONFIG_ATALK is not set -# CONFIG_X25 is not set -# CONFIG_LAPB is not set -# CONFIG_NET_DIVERT is not set -# CONFIG_ECONET is not set -# CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# CONFIG_NET_SCHED=y -CONFIG_NET_SCH_CLK_JIFFIES=y -# CONFIG_NET_SCH_CLK_GETTIMEOFDAY is not set -# CONFIG_NET_SCH_CLK_CPU is not set CONFIG_NET_SCH_CBQ=m CONFIG_NET_SCH_HTB=m -# CONFIG_NET_SCH_HFSC is not set CONFIG_NET_SCH_PRIO=m CONFIG_NET_SCH_RED=m CONFIG_NET_SCH_SFQ=m @@ -257,399 +31,24 @@ CONFIG_NET_SCH_TEQL=m CONFIG_NET_SCH_TBF=m CONFIG_NET_SCH_GRED=m CONFIG_NET_SCH_DSMARK=m -# CONFIG_NET_SCH_NETEM is not set -CONFIG_NET_SCH_INGRESS=m -CONFIG_NET_QOS=y -CONFIG_NET_ESTIMATOR=y -CONFIG_NET_CLS=y CONFIG_NET_CLS_TCINDEX=m CONFIG_NET_CLS_ROUTE4=m -CONFIG_NET_CLS_ROUTE=y CONFIG_NET_CLS_FW=m CONFIG_NET_CLS_U32=m -# CONFIG_CLS_U32_PERF is not set -# CONFIG_NET_CLS_IND is not set CONFIG_NET_CLS_RSVP=m CONFIG_NET_CLS_RSVP6=m -# CONFIG_NET_CLS_ACT is not set -CONFIG_NET_CLS_POLICE=y - -# -# Network testing -# -# CONFIG_NET_PKTGEN is not set -# CONFIG_NETPOLL is not set -# CONFIG_NET_POLL_CONTROLLER is not set -# CONFIG_HAMRADIO is not set -# CONFIG_IRDA is not set -# CONFIG_BT is not set CONFIG_NETDEVICES=y CONFIG_DUMMY=y -# CONFIG_BONDING is not set -# CONFIG_EQUALIZER is not set -# CONFIG_TUN is not set - -# -# ARCnet devices -# -# CONFIG_ARCNET is not set - -# -# Ethernet (10 or 100Mbit) -# -CONFIG_NET_ETHERNET=y -# CONFIG_MII is not set -CONFIG_XT2000_SONIC=y -# CONFIG_HAPPYMEAL is not set -# CONFIG_SUNGEM is not set # CONFIG_NET_VENDOR_3COM is not set - -# -# Tulip family network device support -# -# CONFIG_NET_TULIP is not set -# CONFIG_HP100 is not set -# CONFIG_NET_PCI is not set - -# -# Ethernet (1000 Mbit) -# -# CONFIG_ACENIC is not set -# CONFIG_DL2K is not set -# CONFIG_E1000 is not set -# CONFIG_NS83820 is not set -# CONFIG_HAMACHI is not set -# CONFIG_YELLOWFIN is not set -# CONFIG_R8169 is not set -# CONFIG_SK98LIN is not set -# CONFIG_TIGON3 is not set - -# -# Ethernet (10000 Mbit) -# -# CONFIG_IXGB is not set -# CONFIG_S2IO is not set - -# -# Wireless LAN (non-hamradio) -# -CONFIG_NET_RADIO=y - -# -# Obsolete Wireless cards support (pre-802.11) -# -CONFIG_STRIP=m - -# -# Wireless 802.11b ISA/PCI cards support -# -CONFIG_HERMES=m -# CONFIG_PLX_HERMES is not set -# CONFIG_TMD_HERMES is not set -# CONFIG_PCI_HERMES is not set -# CONFIG_ATMEL is not set - -# -# Prism GT/Duette 802.11(a/b/g) PCI/Cardbus support -# -# CONFIG_PRISM54 is not set -CONFIG_NET_WIRELESS=y - -# -# Wan interfaces -# -# CONFIG_WAN is not set -# CONFIG_FDDI is not set -# CONFIG_HIPPI is not set -# CONFIG_PPP is not set -# CONFIG_SLIP is not set -# CONFIG_SHAPER is not set -# CONFIG_NETCONSOLE is not set - -# -# ISDN subsystem -# -# CONFIG_ISDN is not set - -# -# Telephony Support -# -# CONFIG_PHONE is not set - -# -# Input device support -# -CONFIG_INPUT=y - -# -# Userland interfaces -# -CONFIG_INPUT_MOUSEDEV=y # CONFIG_INPUT_MOUSEDEV_PSAUX is not set -CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 -CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 -# CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set -# CONFIG_INPUT_EVDEV is not set -# CONFIG_INPUT_EVBUG is not set - -# -# Input I/O drivers -# -# CONFIG_GAMEPORT is not set -CONFIG_SOUND_GAMEPORT=y -CONFIG_SERIO=y -# CONFIG_SERIO_I8042 is not set -# CONFIG_SERIO_SERPORT is not set -# CONFIG_SERIO_CT82C710 is not set -# CONFIG_SERIO_PCIPS2 is not set -# CONFIG_SERIO_RAW is not set - -# -# Input Device Drivers -# # CONFIG_INPUT_KEYBOARD is not set # CONFIG_INPUT_MOUSE is not set -# CONFIG_INPUT_JOYSTICK is not set -# CONFIG_INPUT_TOUCHSCREEN is not set -# CONFIG_INPUT_MISC is not set - -# -# Character devices -# -CONFIG_VT=y -CONFIG_VT_CONSOLE=y -CONFIG_HW_CONSOLE=y -# CONFIG_SERIAL_NONSTANDARD is not set - -# -# Serial drivers -# +# CONFIG_SERIO_SERPORT is not set CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y -CONFIG_SERIAL_8250_NR_UARTS=4 -# CONFIG_SERIAL_8250_EXTENDED is not set - -# -# Non-8250 serial port support -# -CONFIG_SERIAL_CORE=y -CONFIG_SERIAL_CORE_CONSOLE=y -CONFIG_UNIX98_PTYS=y -CONFIG_LEGACY_PTYS=y -CONFIG_LEGACY_PTY_COUNT=256 - -# -# IPMI -# -# CONFIG_IPMI_HANDLER is not set - -# -# Watchdog Cards -# -# CONFIG_WATCHDOG is not set -# CONFIG_RTC is not set -# CONFIG_GEN_RTC is not set -# CONFIG_DTLK is not set -# CONFIG_R3964 is not set -# CONFIG_APPLICOM is not set - -# -# Ftape, the floppy tape device driver -# -# CONFIG_DRM is not set -# CONFIG_RAW_DRIVER is not set - -# -# I2C support -# -# CONFIG_I2C is not set - -# -# Dallas's 1-wire bus -# -# CONFIG_W1 is not set - -# -# Misc devices -# - -# -# Multimedia devices -# -# CONFIG_VIDEO_DEV is not set - -# -# Digital Video Broadcasting Devices -# -# CONFIG_DVB is not set - -# -# Graphics support -# -# CONFIG_FB is not set - -# -# Console display driver support -# # CONFIG_VGA_CONSOLE is not set -CONFIG_DUMMY_CONSOLE=y -# CONFIG_BACKLIGHT_LCD_SUPPORT is not set - -# -# Sound -# -# CONFIG_SOUND is not set - -# -# USB support -# -# CONFIG_USB is not set -CONFIG_USB_ARCH_HAS_HCD=y -CONFIG_USB_ARCH_HAS_OHCI=y - -# -# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information -# - -# -# USB Gadget Support -# -# CONFIG_USB_GADGET is not set - -# -# MMC/SD Card support -# -# CONFIG_MMC is not set - -# -# InfiniBand support -# -# CONFIG_INFINIBAND is not set - -# -# File systems -# -# CONFIG_EXT2_FS is not set -# CONFIG_EXT3_FS is not set -# CONFIG_JBD is not set -# CONFIG_REISERFS_FS is not set -# CONFIG_JFS_FS is not set -# CONFIG_XFS_FS is not set -# CONFIG_MINIX_FS is not set -# CONFIG_ROMFS_FS is not set -# CONFIG_QUOTA is not set -CONFIG_DNOTIFY=y -# CONFIG_AUTOFS_FS is not set -# CONFIG_AUTOFS4_FS is not set - -# -# CD-ROM/DVD Filesystems -# -# CONFIG_ISO9660_FS is not set -# CONFIG_UDF_FS is not set - -# -# DOS/FAT/NT Filesystems -# -# CONFIG_MSDOS_FS is not set -# CONFIG_VFAT_FS is not set -# CONFIG_NTFS_FS is not set - -# -# Pseudo filesystems -# -CONFIG_PROC_FS=y -# CONFIG_PROC_KCORE is not set -CONFIG_SYSFS=y -CONFIG_DEVFS_FS=y -# CONFIG_DEVFS_MOUNT is not set -# CONFIG_DEVFS_DEBUG is not set -# CONFIG_DEVPTS_FS_XATTR is not set -# CONFIG_TMPFS is not set -# CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y - -# -# Miscellaneous filesystems -# -# CONFIG_ADFS_FS is not set -# CONFIG_AFFS_FS is not set -# CONFIG_HFS_FS is not set -# CONFIG_HFSPLUS_FS is not set -# CONFIG_BEFS_FS is not set -# CONFIG_BFS_FS is not set -# CONFIG_EFS_FS is not set -# CONFIG_CRAMFS is not set -# CONFIG_VXFS_FS is not set -# CONFIG_HPFS_FS is not set -# CONFIG_QNX4FS_FS is not set -# CONFIG_SYSV_FS is not set -# CONFIG_UFS_FS is not set - -# -# Network File Systems -# CONFIG_NFS_FS=y -CONFIG_NFS_V3=y -# CONFIG_NFS_V4 is not set -# CONFIG_NFS_DIRECTIO is not set -# CONFIG_NFSD is not set CONFIG_ROOT_NFS=y -CONFIG_LOCKD=y -CONFIG_LOCKD_V4=y -# CONFIG_EXPORTFS is not set -CONFIG_SUNRPC=y -# CONFIG_RPCSEC_GSS_KRB5 is not set -# CONFIG_RPCSEC_GSS_SPKM3 is not set -# CONFIG_SMB_FS is not set -# CONFIG_CIFS is not set -# CONFIG_NCP_FS is not set -# CONFIG_CODA_FS is not set -# CONFIG_AFS_FS is not set - -# -# Partition Types -# -# CONFIG_PARTITION_ADVANCED is not set -CONFIG_MSDOS_PARTITION=y - -# -# Native Language Support -# -# CONFIG_NLS is not set - -# -# Kernel hacking -# -CONFIG_DEBUG_KERNEL=y -# CONFIG_DEBUG_STACKOVERFLOW is not set -# CONFIG_DEBUG_SLAB is not set +# CONFIG_FRAME_POINTER is not set CONFIG_MAGIC_SYSRQ=y -# CONFIG_DEBUG_SPINLOCK is not set -# CONFIG_DEBUG_PAGEALLOC is not set -# CONFIG_DEBUG_INFO is not set -# CONFIG_DEBUG_SPINLOCK_SLEEP is not set -# CONFIG_KGDB is not set - -# -# Security options -# -# CONFIG_KEYS is not set -# CONFIG_SECURITY is not set - -# -# Cryptographic options -# -# CONFIG_CRYPTO is not set - -# -# Hardware crypto devices -# - -# -# Library routines -# -# CONFIG_CRC_CCITT is not set -# CONFIG_CRC32 is not set -# CONFIG_LIBCRC32C is not set +CONFIG_DEBUG_KERNEL=y diff --git a/arch/xtensa/configs/generic_kc705_defconfig b/arch/xtensa/configs/generic_kc705_defconfig index d9444f01f4da9ec154faee399953253081761004..744adeaf2945496d4b3a89cc11518a1d5ea7acbb 100644 --- a/arch/xtensa/configs/generic_kc705_defconfig +++ b/arch/xtensa/configs/generic_kc705_defconfig @@ -32,7 +32,7 @@ CONFIG_HIGHMEM=y # CONFIG_PCI is not set CONFIG_XTENSA_PLATFORM_XTFPGA=y CONFIG_CMDLINE_BOOL=y -CONFIG_CMDLINE="earlycon=uart8250,mmio32,0xfd050020,115200n8 console=ttyS0,115200n8 ip=dhcp root=/dev/nfs rw debug" +CONFIG_CMDLINE="earlycon=uart8250,mmio32native,0xfd050020,115200n8 console=ttyS0,115200n8 ip=dhcp root=/dev/nfs rw debug memmap=0x38000000@0" CONFIG_USE_OF=y CONFIG_BUILTIN_DTB="kc705" # CONFIG_COMPACTION is not set diff --git a/arch/xtensa/configs/iss_defconfig b/arch/xtensa/configs/iss_defconfig index 44c6764d9146347d713a8d377d612ae7970f9e96..4bb5b76d95245b97919be23d0bdcfe7801888f4e 100644 --- a/arch/xtensa/configs/iss_defconfig +++ b/arch/xtensa/configs/iss_defconfig @@ -1,758 +1,34 @@ -# -# Automatically generated make config: don't edit -# Linux kernel version: 2.6.34-rc6 -# Tue Aug 3 00:10:54 2010 -# -# CONFIG_FRAME_POINTER is not set -CONFIG_ZONE_DMA=y -CONFIG_XTENSA=y -CONFIG_RWSEM_XCHGADD_ALGORITHM=y -CONFIG_GENERIC_FIND_NEXT_BIT=y -CONFIG_GENERIC_HWEIGHT=y -# CONFIG_ARCH_HAS_ILOG2_U32 is not set -# CONFIG_ARCH_HAS_ILOG2_U64 is not set -CONFIG_NO_IOPORT_MAP=y -CONFIG_HZ=100 -CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" -CONFIG_CONSTRUCTORS=y - -# -# General setup -# -CONFIG_EXPERIMENTAL=y -CONFIG_BROKEN_ON_SMP=y -CONFIG_INIT_ENV_ARG_LIMIT=32 -CONFIG_LOCALVERSION="" -CONFIG_LOCALVERSION_AUTO=y -CONFIG_SWAP=y CONFIG_SYSVIPC=y -CONFIG_SYSVIPC_SYSCTL=y -# CONFIG_POSIX_MQUEUE is not set -# CONFIG_BSD_PROCESS_ACCT is not set -# CONFIG_TASKSTATS is not set -# CONFIG_AUDIT is not set - -# -# RCU Subsystem -# -CONFIG_TREE_RCU=y -# CONFIG_TREE_PREEMPT_RCU is not set -# CONFIG_TINY_RCU is not set -# CONFIG_RCU_TRACE is not set -CONFIG_RCU_FANOUT=32 -# CONFIG_RCU_FANOUT_EXACT is not set -# CONFIG_TREE_RCU_TRACE is not set -# CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 -# CONFIG_CGROUPS is not set -# CONFIG_SYSFS_DEPRECATED_V2 is not set -# CONFIG_RELAY is not set -# CONFIG_NAMESPACES is not set -# CONFIG_BLK_DEV_INITRD is not set -# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set -CONFIG_SYSCTL=y -CONFIG_ANON_INODES=y CONFIG_EXPERT=y CONFIG_SYSCTL_SYSCALL=y -CONFIG_KALLSYMS=y -# CONFIG_KALLSYMS_ALL is not set -# CONFIG_KALLSYMS_EXTRA_PASS is not set -# CONFIG_HOTPLUG is not set -CONFIG_PRINTK=y -CONFIG_BUG=y -CONFIG_ELF_CORE=y -CONFIG_BASE_FULL=y -CONFIG_FUTEX=y -CONFIG_EPOLL=y -CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y -CONFIG_EVENTFD=y -CONFIG_SHMEM=y -CONFIG_AIO=y - -# -# Kernel Performance Events And Counters -# -CONFIG_VM_EVENT_COUNTERS=y -CONFIG_SLUB_DEBUG=y -CONFIG_COMPAT_BRK=y -# CONFIG_SLAB is not set -CONFIG_SLUB=y -# CONFIG_SLOB is not set -# CONFIG_PROFILING is not set - -# -# GCOV-based kernel profiling -# -# CONFIG_SLOW_WORK is not set -# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set -CONFIG_SLABINFO=y -CONFIG_RT_MUTEXES=y -CONFIG_BASE_SMALL=0 -# CONFIG_MODULES is not set -CONFIG_BLOCK=y -CONFIG_LBDAF=y -CONFIG_BLK_DEV_BSG=y -# CONFIG_BLK_DEV_INTEGRITY is not set - -# -# IO Schedulers -# -CONFIG_IOSCHED_NOOP=y # CONFIG_IOSCHED_DEADLINE is not set # CONFIG_IOSCHED_CFQ is not set -# CONFIG_DEFAULT_DEADLINE is not set -# CONFIG_DEFAULT_CFQ is not set -CONFIG_DEFAULT_NOOP=y -CONFIG_DEFAULT_IOSCHED="noop" -# CONFIG_INLINE_SPIN_TRYLOCK is not set -# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set -# CONFIG_INLINE_SPIN_LOCK is not set -# CONFIG_INLINE_SPIN_LOCK_BH is not set -# CONFIG_INLINE_SPIN_LOCK_IRQ is not set -# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set -# CONFIG_UNINLINE_SPIN_UNLOCK is not set -# CONFIG_INLINE_SPIN_UNLOCK_BH is not set -CONFIG_INLINE_SPIN_UNLOCK_IRQ=y -# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set -# CONFIG_INLINE_READ_TRYLOCK is not set -# CONFIG_INLINE_READ_LOCK is not set -# CONFIG_INLINE_READ_LOCK_BH is not set -# CONFIG_INLINE_READ_LOCK_IRQ is not set -# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set -CONFIG_INLINE_READ_UNLOCK=y -# CONFIG_INLINE_READ_UNLOCK_BH is not set -CONFIG_INLINE_READ_UNLOCK_IRQ=y -# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set -# CONFIG_INLINE_WRITE_TRYLOCK is not set -# CONFIG_INLINE_WRITE_LOCK is not set -# CONFIG_INLINE_WRITE_LOCK_BH is not set -# CONFIG_INLINE_WRITE_LOCK_IRQ is not set -# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set -CONFIG_INLINE_WRITE_UNLOCK=y -# CONFIG_INLINE_WRITE_UNLOCK_BH is not set -CONFIG_INLINE_WRITE_UNLOCK_IRQ=y -# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set -# CONFIG_MUTEX_SPIN_ON_OWNER is not set -# CONFIG_FREEZER is not set -CONFIG_MMU=y -# CONFIG_VARIANT_IRQ_SWITCH is not set - -# -# Processor type and features -# -CONFIG_XTENSA_VARIANT_FSF=y -# CONFIG_XTENSA_VARIANT_DC232B is not set -# CONFIG_XTENSA_UNALIGNED_USER is not set -# CONFIG_PREEMPT is not set -CONFIG_XTENSA_CALIBRATE_CCOUNT=y -CONFIG_SERIAL_CONSOLE=y -CONFIG_XTENSA_ISS_NETWORK=y - -# -# Bus options -# # CONFIG_PCI is not set -# CONFIG_ARCH_SUPPORTS_MSI is not set - -# -# Platform options -# -CONFIG_XTENSA_PLATFORM_ISS=y -# CONFIG_XTENSA_PLATFORM_XT2000 is not set -# CONFIG_GENERIC_CALIBRATE_DELAY is not set CONFIG_CMDLINE_BOOL=y -CONFIG_CMDLINE="console=ttyS0,38400 eth0=tuntap,,tap0 ip=192.168.168.5:192.168.168.1 root=nfs nfsroot=192.168.168.1:/opt/montavista/pro/devkit/xtensa/linux_be/target" -CONFIG_SELECT_MEMORY_MODEL=y -CONFIG_FLATMEM_MANUAL=y -# CONFIG_DISCONTIGMEM_MANUAL is not set -# CONFIG_SPARSEMEM_MANUAL is not set -CONFIG_FLATMEM=y -CONFIG_FLAT_NODE_MEM_MAP=y -CONFIG_SPLIT_PTLOCK_CPUS=4 -# CONFIG_PHYS_ADDR_T_64BIT is not set -CONFIG_ZONE_DMA_FLAG=1 -CONFIG_BOUNCE=y -CONFIG_VIRT_TO_BUS=y -# CONFIG_KSM is not set -CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 - -# -# Executable file formats -# -CONFIG_KCORE_ELF=y -CONFIG_BINFMT_ELF=y +CONFIG_CMDLINE="console=ttyS0,38400 eth0=tuntap,,tap0 ip=192.168.168.5:192.168.168.1 root=nfs nfsroot=192.168.168.1:/opt/montavista/pro/devkit/xtensa/linux_be/target memmap=128M@0" # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set -# CONFIG_HAVE_AOUT is not set -# CONFIG_BINFMT_MISC is not set CONFIG_NET=y - -# -# Networking options -# CONFIG_PACKET=y CONFIG_UNIX=y -CONFIG_XFRM=y -# CONFIG_XFRM_USER is not set -# CONFIG_XFRM_SUB_POLICY is not set -# CONFIG_XFRM_MIGRATE is not set -# CONFIG_XFRM_STATISTICS is not set -# CONFIG_NET_KEY is not set CONFIG_INET=y -# CONFIG_IP_MULTICAST is not set -# CONFIG_IP_ADVANCED_ROUTER is not set -CONFIG_IP_FIB_HASH=y CONFIG_IP_PNP=y CONFIG_IP_PNP_DHCP=y CONFIG_IP_PNP_BOOTP=y CONFIG_IP_PNP_RARP=y -# CONFIG_NET_IPIP is not set -# CONFIG_NET_IPGRE is not set -# CONFIG_ARPD is not set -# CONFIG_SYN_COOKIES is not set -# CONFIG_INET_AH is not set -# CONFIG_INET_ESP is not set -# CONFIG_INET_IPCOMP is not set -# CONFIG_INET_XFRM_TUNNEL is not set -# CONFIG_INET_TUNNEL is not set -CONFIG_INET_XFRM_MODE_TRANSPORT=y -CONFIG_INET_XFRM_MODE_TUNNEL=y -CONFIG_INET_XFRM_MODE_BEET=y -CONFIG_INET_LRO=y -CONFIG_INET_DIAG=y -CONFIG_INET_TCP_DIAG=y -# CONFIG_TCP_CONG_ADVANCED is not set -CONFIG_TCP_CONG_CUBIC=y -CONFIG_DEFAULT_TCP_CONG="cubic" -# CONFIG_TCP_MD5SIG is not set # CONFIG_IPV6 is not set -# CONFIG_NETWORK_SECMARK is not set -# CONFIG_NETFILTER is not set -# CONFIG_IP_DCCP is not set -# CONFIG_IP_SCTP is not set -# CONFIG_RDS is not set -# CONFIG_TIPC is not set -# CONFIG_ATM is not set -# CONFIG_BRIDGE is not set -# CONFIG_NET_DSA is not set -# CONFIG_VLAN_8021Q is not set -# CONFIG_DECNET is not set -# CONFIG_LLC2 is not set -# CONFIG_IPX is not set -# CONFIG_ATALK is not set -# CONFIG_X25 is not set -# CONFIG_LAPB is not set -# CONFIG_ECONET is not set -# CONFIG_WAN_ROUTER is not set -# CONFIG_PHONET is not set -# CONFIG_IEEE802154 is not set -# CONFIG_NET_SCHED is not set -# CONFIG_DCB is not set - -# -# Network testing -# -# CONFIG_NET_PKTGEN is not set -# CONFIG_HAMRADIO is not set -# CONFIG_CAN is not set -# CONFIG_IRDA is not set -# CONFIG_BT is not set -# CONFIG_AF_RXRPC is not set -CONFIG_WIRELESS=y -# CONFIG_CFG80211 is not set -# CONFIG_LIB80211 is not set - -# -# CFG80211 needs to be enabled for MAC80211 -# -# CONFIG_WIMAX is not set -# CONFIG_RFKILL is not set -# CONFIG_NET_9P is not set - -# -# Device Drivers -# - -# -# Generic Driver Options -# # CONFIG_STANDALONE is not set -CONFIG_PREVENT_FIRMWARE_BUILD=y -# CONFIG_DEBUG_DRIVER is not set -# CONFIG_DEBUG_DEVRES is not set -# CONFIG_SYS_HYPERVISOR is not set -# CONFIG_CONNECTOR is not set -# CONFIG_MTD is not set -# CONFIG_PARPORT is not set -CONFIG_BLK_DEV=y -# CONFIG_BLK_DEV_COW_COMMON is not set -# CONFIG_BLK_DEV_LOOP is not set - -# -# DRBD disabled because PROC_FS, INET or CONNECTOR not selected -# -# CONFIG_BLK_DEV_NBD is not set -# CONFIG_BLK_DEV_RAM is not set -# CONFIG_CDROM_PKTCDVD is not set -# CONFIG_ATA_OVER_ETH is not set -# CONFIG_BLK_DEV_HD is not set -CONFIG_MISC_DEVICES=y -# CONFIG_ENCLOSURE_SERVICES is not set -# CONFIG_C2PORT is not set - -# -# EEPROM support -# -# CONFIG_EEPROM_93CX6 is not set -# CONFIG_HAVE_IDE is not set -# CONFIG_IDE is not set - -# -# SCSI device support -# -CONFIG_SCSI_MOD=y -# CONFIG_RAID_ATTRS is not set -# CONFIG_SCSI is not set -# CONFIG_SCSI_DMA is not set -# CONFIG_SCSI_NETLINK is not set -# CONFIG_ATA is not set -# CONFIG_MD is not set -# CONFIG_NETDEVICES is not set -# CONFIG_ISDN is not set -# CONFIG_PHONE is not set - -# -# Input device support -# -CONFIG_INPUT=y -# CONFIG_INPUT_FF_MEMLESS is not set -# CONFIG_INPUT_POLLDEV is not set -# CONFIG_INPUT_SPARSEKMAP is not set - -# -# Userland interfaces -# # CONFIG_INPUT_MOUSEDEV is not set -# CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_EVDEV is not set -# CONFIG_INPUT_EVBUG is not set - -# -# Input Device Drivers -# # CONFIG_INPUT_KEYBOARD is not set # CONFIG_INPUT_MOUSE is not set -# CONFIG_INPUT_JOYSTICK is not set -# CONFIG_INPUT_TABLET is not set -# CONFIG_INPUT_TOUCHSCREEN is not set -# CONFIG_INPUT_MISC is not set - -# -# Hardware I/O ports -# # CONFIG_SERIO is not set -# CONFIG_GAMEPORT is not set - -# -# Character devices -# -CONFIG_VT=y -CONFIG_CONSOLE_TRANSLATIONS=y -CONFIG_VT_CONSOLE=y -CONFIG_HW_CONSOLE=y -# CONFIG_VT_HW_CONSOLE_BINDING is not set -CONFIG_DEVKMEM=y -# CONFIG_SERIAL_NONSTANDARD is not set - -# -# Serial drivers -# -# CONFIG_SERIAL_8250 is not set - -# -# Non-8250 serial port support -# -# CONFIG_SERIAL_TIMBERDALE is not set -CONFIG_UNIX98_PTYS=y -# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set -CONFIG_LEGACY_PTYS=y -CONFIG_LEGACY_PTY_COUNT=256 -# CONFIG_IPMI_HANDLER is not set -CONFIG_HW_RANDOM=y -# CONFIG_HW_RANDOM_TIMERIOMEM is not set -# CONFIG_RTC is not set -# CONFIG_GEN_RTC is not set -# CONFIG_R3964 is not set -# CONFIG_RAW_DRIVER is not set -# CONFIG_TCG_TPM is not set -# CONFIG_I2C is not set -# CONFIG_SPI is not set - -# -# PPS support -# -# CONFIG_PPS is not set -# CONFIG_W1 is not set -# CONFIG_POWER_SUPPLY is not set -CONFIG_HWMON=y -# CONFIG_HWMON_VID is not set -# CONFIG_HWMON_DEBUG_CHIP is not set - -# -# Native drivers -# -# CONFIG_SENSORS_F71805F is not set -# CONFIG_SENSORS_F71882FG is not set -# CONFIG_SENSORS_IT87 is not set -# CONFIG_SENSORS_PC87360 is not set -# CONFIG_SENSORS_PC87427 is not set -# CONFIG_SENSORS_SHT15 is not set -# CONFIG_SENSORS_SMSC47M1 is not set -# CONFIG_SENSORS_SMSC47B397 is not set -# CONFIG_SENSORS_VT1211 is not set -# CONFIG_SENSORS_W83627HF is not set -# CONFIG_SENSORS_W83627EHF is not set -# CONFIG_THERMAL is not set CONFIG_WATCHDOG=y CONFIG_WATCHDOG_NOWAYOUT=y - -# -# Watchdog Device Drivers -# CONFIG_SOFT_WATCHDOG=y -CONFIG_SSB_POSSIBLE=y - -# -# Sonics Silicon Backplane -# -# CONFIG_SSB is not set - -# -# Multifunction device drivers -# -# CONFIG_MFD_CORE is not set -# CONFIG_MFD_SM501 is not set -# CONFIG_HTC_PASIC3 is not set -# CONFIG_MFD_TMIO is not set -# CONFIG_REGULATOR is not set -# CONFIG_MEDIA_SUPPORT is not set - -# -# Graphics support -# -# CONFIG_VGASTATE is not set -# CONFIG_VIDEO_OUTPUT_CONTROL is not set -# CONFIG_FB is not set -# CONFIG_BACKLIGHT_LCD_SUPPORT is not set - -# -# Display device support -# -# CONFIG_DISPLAY_SUPPORT is not set - -# -# Console display driver support -# # CONFIG_VGA_CONSOLE is not set -CONFIG_DUMMY_CONSOLE=y -# CONFIG_SOUND is not set -CONFIG_HID_SUPPORT=y -CONFIG_HID=y -# CONFIG_HIDRAW is not set -# CONFIG_HID_PID is not set - -# -# Special HID drivers -# -CONFIG_USB_SUPPORT=y -# CONFIG_USB_ARCH_HAS_HCD is not set -# CONFIG_USB_ARCH_HAS_OHCI is not set -# CONFIG_USB_ARCH_HAS_EHCI is not set -# CONFIG_USB_OTG_WHITELIST is not set -# CONFIG_USB_OTG_BLACKLIST_HUB is not set - -# -# Enable Host or Gadget support to see Inventra options -# - -# -# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may -# -# CONFIG_USB_GADGET is not set - -# -# OTG and related infrastructure -# -# CONFIG_MMC is not set -# CONFIG_MEMSTICK is not set -# CONFIG_NEW_LEDS is not set -# CONFIG_ACCESSIBILITY is not set -# CONFIG_RTC_CLASS is not set -# CONFIG_DMADEVICES is not set -# CONFIG_AUXDISPLAY is not set -# CONFIG_UIO is not set - -# -# TI VLYNQ -# -# CONFIG_STAGING is not set - -# -# File systems -# -# CONFIG_EXT2_FS is not set -# CONFIG_EXT3_FS is not set -# CONFIG_EXT4_FS is not set -# CONFIG_REISERFS_FS is not set -# CONFIG_JFS_FS is not set -# CONFIG_FS_POSIX_ACL is not set -# CONFIG_XFS_FS is not set -# CONFIG_GFS2_FS is not set -# CONFIG_OCFS2_FS is not set -# CONFIG_BTRFS_FS is not set -# CONFIG_NILFS2_FS is not set -CONFIG_FILE_LOCKING=y -CONFIG_FSNOTIFY=y # CONFIG_DNOTIFY is not set -# CONFIG_INOTIFY is not set -CONFIG_INOTIFY_USER=y -# CONFIG_QUOTA is not set -# CONFIG_AUTOFS_FS is not set -# CONFIG_AUTOFS4_FS is not set -# CONFIG_FUSE_FS is not set - -# -# Caches -# -# CONFIG_FSCACHE is not set - -# -# CD-ROM/DVD Filesystems -# -# CONFIG_ISO9660_FS is not set -# CONFIG_UDF_FS is not set - -# -# DOS/FAT/NT Filesystems -# -# CONFIG_MSDOS_FS is not set -# CONFIG_VFAT_FS is not set -# CONFIG_NTFS_FS is not set - -# -# Pseudo filesystems -# -CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y -CONFIG_PROC_SYSCTL=y -CONFIG_PROC_PAGE_MONITOR=y -CONFIG_SYSFS=y CONFIG_TMPFS=y -# CONFIG_TMPFS_POSIX_ACL is not set -# CONFIG_HUGETLB_PAGE is not set -# CONFIG_CONFIGFS_FS is not set -CONFIG_MISC_FILESYSTEMS=y -# CONFIG_ADFS_FS is not set -# CONFIG_AFFS_FS is not set -# CONFIG_HFS_FS is not set -# CONFIG_HFSPLUS_FS is not set -# CONFIG_BEFS_FS is not set -# CONFIG_BFS_FS is not set -# CONFIG_EFS_FS is not set -# CONFIG_LOGFS is not set -# CONFIG_CRAMFS is not set -# CONFIG_SQUASHFS is not set -# CONFIG_VXFS_FS is not set -# CONFIG_MINIX_FS is not set -# CONFIG_OMFS_FS is not set -# CONFIG_HPFS_FS is not set -# CONFIG_QNX4FS_FS is not set -# CONFIG_ROMFS_FS is not set -# CONFIG_SYSV_FS is not set -# CONFIG_UFS_FS is not set -CONFIG_NETWORK_FILESYSTEMS=y -# CONFIG_NFS_FS is not set -# CONFIG_NFSD is not set -# CONFIG_SMB_FS is not set -# CONFIG_CEPH_FS is not set -# CONFIG_CIFS is not set -# CONFIG_NCP_FS is not set -# CONFIG_CODA_FS is not set -# CONFIG_AFS_FS is not set - -# -# Partition Types -# -# CONFIG_PARTITION_ADVANCED is not set -CONFIG_MSDOS_PARTITION=y -# CONFIG_NLS is not set -# CONFIG_DLM is not set - -# -# Kernel hacking -# -# CONFIG_PRINTK_TIME is not set -CONFIG_ENABLE_WARN_DEPRECATED=y -CONFIG_ENABLE_MUST_CHECK=y -CONFIG_FRAME_WARN=1024 -# CONFIG_MAGIC_SYSRQ is not set -# CONFIG_STRIP_ASM_SYMS is not set -# CONFIG_UNUSED_SYMBOLS is not set -# CONFIG_DEBUG_FS is not set -# CONFIG_HEADERS_CHECK is not set -CONFIG_DEBUG_KERNEL=y -# CONFIG_DEBUG_SHIRQ is not set -CONFIG_DETECT_SOFTLOCKUP=y -# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set -CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 +# CONFIG_FRAME_POINTER is not set CONFIG_DETECT_HUNG_TASK=y -# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set -CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0 -CONFIG_SCHED_DEBUG=y -# CONFIG_SCHEDSTATS is not set -# CONFIG_TIMER_STATS is not set -# CONFIG_DEBUG_OBJECTS is not set -# CONFIG_SLUB_DEBUG_ON is not set -# CONFIG_SLUB_STATS is not set -# CONFIG_DEBUG_RT_MUTEXES is not set -# CONFIG_DEBUG_SPINLOCK is not set -# CONFIG_DEBUG_MUTEXES is not set -# CONFIG_DEBUG_SPINLOCK_SLEEP is not set -# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set -# CONFIG_DEBUG_KOBJECT is not set -# CONFIG_DEBUG_INFO is not set -# CONFIG_DEBUG_VM is not set -# CONFIG_DEBUG_MEMORY_INIT is not set -# CONFIG_DEBUG_LIST is not set -# CONFIG_DEBUG_SG is not set -# CONFIG_DEBUG_NOTIFIERS is not set -# CONFIG_DEBUG_CREDENTIALS is not set -# CONFIG_RCU_TORTURE_TEST is not set -CONFIG_RCU_CPU_STALL_DETECTOR=y -# CONFIG_BACKTRACE_SELF_TEST is not set -# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set -# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set -# CONFIG_FAULT_INJECTION is not set -# CONFIG_SYSCTL_SYSCALL_CHECK is not set -# CONFIG_PAGE_POISONING is not set -# CONFIG_SAMPLES is not set - -# -# Security options -# -# CONFIG_KEYS is not set -# CONFIG_SECURITY is not set -# CONFIG_SECURITYFS is not set -# CONFIG_DEFAULT_SECURITY_SELINUX is not set -# CONFIG_DEFAULT_SECURITY_SMACK is not set -# CONFIG_DEFAULT_SECURITY_TOMOYO is not set -CONFIG_DEFAULT_SECURITY_DAC=y -CONFIG_DEFAULT_SECURITY="" -CONFIG_CRYPTO=y - -# -# Crypto core or helper -# -# CONFIG_CRYPTO_FIPS is not set -CONFIG_CRYPTO_ALGAPI=y -CONFIG_CRYPTO_ALGAPI2=y -CONFIG_CRYPTO_RNG=y -CONFIG_CRYPTO_RNG2=y -# CONFIG_CRYPTO_MANAGER is not set -# CONFIG_CRYPTO_MANAGER2 is not set -# CONFIG_CRYPTO_GF128MUL is not set -# CONFIG_CRYPTO_NULL is not set -# CONFIG_CRYPTO_CRYPTD is not set -# CONFIG_CRYPTO_AUTHENC is not set - -# -# Authenticated Encryption with Associated Data -# -# CONFIG_CRYPTO_CCM is not set -# CONFIG_CRYPTO_GCM is not set -# CONFIG_CRYPTO_SEQIV is not set - -# -# Block modes -# -# CONFIG_CRYPTO_CBC is not set -# CONFIG_CRYPTO_CTR is not set -# CONFIG_CRYPTO_CTS is not set -# CONFIG_CRYPTO_ECB is not set -# CONFIG_CRYPTO_LRW is not set -# CONFIG_CRYPTO_PCBC is not set -# CONFIG_CRYPTO_XTS is not set - -# -# Hash modes -# -# CONFIG_CRYPTO_HMAC is not set -# CONFIG_CRYPTO_XCBC is not set -# CONFIG_CRYPTO_VMAC is not set - -# -# Digest -# -# CONFIG_CRYPTO_CRC32C is not set -# CONFIG_CRYPTO_GHASH is not set -# CONFIG_CRYPTO_MD4 is not set -# CONFIG_CRYPTO_MD5 is not set -# CONFIG_CRYPTO_MICHAEL_MIC is not set -# CONFIG_CRYPTO_RMD128 is not set -# CONFIG_CRYPTO_RMD160 is not set -# CONFIG_CRYPTO_RMD256 is not set -# CONFIG_CRYPTO_RMD320 is not set -# CONFIG_CRYPTO_SHA1 is not set -# CONFIG_CRYPTO_SHA256 is not set -# CONFIG_CRYPTO_SHA512 is not set -# CONFIG_CRYPTO_TGR192 is not set -# CONFIG_CRYPTO_WP512 is not set - -# -# Ciphers -# -CONFIG_CRYPTO_AES=y -# CONFIG_CRYPTO_ANUBIS is not set -# CONFIG_CRYPTO_ARC4 is not set -# CONFIG_CRYPTO_BLOWFISH is not set -# CONFIG_CRYPTO_CAMELLIA is not set -# CONFIG_CRYPTO_CAST5 is not set -# CONFIG_CRYPTO_CAST6 is not set -# CONFIG_CRYPTO_DES is not set -# CONFIG_CRYPTO_FCRYPT is not set -# CONFIG_CRYPTO_KHAZAD is not set -# CONFIG_CRYPTO_SALSA20 is not set -# CONFIG_CRYPTO_SEED is not set -# CONFIG_CRYPTO_SERPENT is not set -# CONFIG_CRYPTO_TEA is not set -# CONFIG_CRYPTO_TWOFISH is not set - -# -# Compression -# -# CONFIG_CRYPTO_DEFLATE is not set -# CONFIG_CRYPTO_ZLIB is not set -# CONFIG_CRYPTO_LZO is not set - -# -# Random Number Generation -# CONFIG_CRYPTO_ANSI_CPRNG=y -CONFIG_CRYPTO_HW=y -# CONFIG_BINARY_PRINTF is not set - -# -# Library routines -# -CONFIG_GENERIC_FIND_LAST_BIT=y -# CONFIG_CRC_CCITT is not set -# CONFIG_CRC16 is not set -# CONFIG_CRC_T10DIF is not set -# CONFIG_CRC_ITU_T is not set -# CONFIG_CRC32 is not set -# CONFIG_CRC7 is not set -# CONFIG_LIBCRC32C is not set -CONFIG_HAS_IOMEM=y -CONFIG_HAS_DMA=y -CONFIG_NLATTR=y -CONFIG_LD_NO_RELAX=y diff --git a/arch/xtensa/configs/nommu_kc705_defconfig b/arch/xtensa/configs/nommu_kc705_defconfig index 337d5ba2d285cf1bc4921139fe9198bc4c8bb23d..78c2529d04592dea76f7e76219cfd60e35815292 100644 --- a/arch/xtensa/configs/nommu_kc705_defconfig +++ b/arch/xtensa/configs/nommu_kc705_defconfig @@ -37,7 +37,7 @@ CONFIG_PREEMPT=y # CONFIG_PCI is not set CONFIG_XTENSA_PLATFORM_XTFPGA=y CONFIG_CMDLINE_BOOL=y -CONFIG_CMDLINE="earlycon=uart8250,mmio32,0x9d050020,115200n8 console=ttyS0,115200n8 ip=dhcp root=/dev/nfs rw debug" +CONFIG_CMDLINE="earlycon=uart8250,mmio32native,0x9d050020,115200n8 console=ttyS0,115200n8 ip=dhcp root=/dev/nfs rw debug memmap=256M@0x60000000" CONFIG_USE_OF=y CONFIG_BUILTIN_DTB="kc705_nommu" CONFIG_DEFAULT_MEM_SIZE=0x10000000 diff --git a/arch/xtensa/configs/smp_lx200_defconfig b/arch/xtensa/configs/smp_lx200_defconfig index 61f943c956198500f63f0e1f90154d36ee46a30a..14e3ca353ac8aa78bab2fe9a7be09ffef519010b 100644 --- a/arch/xtensa/configs/smp_lx200_defconfig +++ b/arch/xtensa/configs/smp_lx200_defconfig @@ -36,7 +36,7 @@ CONFIG_HOTPLUG_CPU=y # CONFIG_PCI is not set CONFIG_XTENSA_PLATFORM_XTFPGA=y CONFIG_CMDLINE_BOOL=y -CONFIG_CMDLINE="earlycon=uart8250,mmio32,0xfd050020,115200n8 console=ttyS0,115200n8 ip=dhcp root=/dev/nfs rw debug" +CONFIG_CMDLINE="earlycon=uart8250,mmio32native,0xfd050020,115200n8 console=ttyS0,115200n8 ip=dhcp root=/dev/nfs rw debug memmap=96M@0" CONFIG_USE_OF=y CONFIG_BUILTIN_DTB="lx200mx" # CONFIG_COMPACTION is not set diff --git a/arch/xtensa/include/asm/bitops.h b/arch/xtensa/include/asm/bitops.h index 3f44fa2a53e9fcde4266717bd245d15c0b530559..d3490189792b08a22962d9784c40472eaf5907b4 100644 --- a/arch/xtensa/include/asm/bitops.h +++ b/arch/xtensa/include/asm/bitops.h @@ -48,7 +48,7 @@ static inline int ffz(unsigned long x) * __ffs: Find first bit set in word. Return 0 for bit 0 */ -static inline int __ffs(unsigned long x) +static inline unsigned long __ffs(unsigned long x) { return 31 - __cntlz(x & -x); } diff --git a/arch/xtensa/include/asm/cacheasm.h b/arch/xtensa/include/asm/cacheasm.h index e0f9e1109c833c67eff94075973c8dd5c524ee3e..2041abb10a2352a4b1f4323f3e1f0d9bdfff36ec 100644 --- a/arch/xtensa/include/asm/cacheasm.h +++ b/arch/xtensa/include/asm/cacheasm.h @@ -69,26 +69,23 @@ .endm -#if XCHAL_DCACHE_LINE_LOCKABLE - .macro ___unlock_dcache_all ar at -#if XCHAL_DCACHE_SIZE +#if XCHAL_DCACHE_LINE_LOCKABLE && XCHAL_DCACHE_SIZE __loop_cache_all \ar \at diu XCHAL_DCACHE_SIZE XCHAL_DCACHE_LINEWIDTH #endif .endm -#endif - -#if XCHAL_ICACHE_LINE_LOCKABLE .macro ___unlock_icache_all ar at +#if XCHAL_ICACHE_LINE_LOCKABLE && XCHAL_ICACHE_SIZE __loop_cache_all \ar \at iiu XCHAL_ICACHE_SIZE XCHAL_ICACHE_LINEWIDTH +#endif .endm -#endif + .macro ___flush_invalidate_dcache_all ar at diff --git a/arch/xtensa/include/asm/fixmap.h b/arch/xtensa/include/asm/fixmap.h index 62b507deea9da136cc26cf32388a5a3358efa251..0d30403b6c95977c6467cd130ac78889c406e240 100644 --- a/arch/xtensa/include/asm/fixmap.h +++ b/arch/xtensa/include/asm/fixmap.h @@ -59,6 +59,11 @@ enum fixed_addresses { */ static __always_inline unsigned long fix_to_virt(const unsigned int idx) { + /* Check if this memory layout is broken because fixmap overlaps page + * table. + */ + BUILD_BUG_ON(FIXADDR_START < + XCHAL_PAGE_TABLE_VADDR + XCHAL_PAGE_TABLE_SIZE); BUILD_BUG_ON(idx >= __end_of_fixed_addresses); return __fix_to_virt(idx); } diff --git a/arch/xtensa/include/asm/highmem.h b/arch/xtensa/include/asm/highmem.h index 01cef6b40829adb87460f9b2b8d141853ed4f45d..6e070db1022e69e55a229117839463057edc8a30 100644 --- a/arch/xtensa/include/asm/highmem.h +++ b/arch/xtensa/include/asm/highmem.h @@ -68,6 +68,11 @@ void kunmap_high(struct page *page); static inline void *kmap(struct page *page) { + /* Check if this memory layout is broken because PKMAP overlaps + * page table. + */ + BUILD_BUG_ON(PKMAP_BASE < + XCHAL_PAGE_TABLE_VADDR + XCHAL_PAGE_TABLE_SIZE); BUG_ON(in_interrupt()); if (!PageHighMem(page)) return page_address(page); diff --git a/arch/xtensa/include/asm/initialize_mmu.h b/arch/xtensa/include/asm/initialize_mmu.h index 7a1e075969a353a54b1763d9d4069e98bb0af519..42410f253597d5e772da628df4d042ed485cde4f 100644 --- a/arch/xtensa/include/asm/initialize_mmu.h +++ b/arch/xtensa/include/asm/initialize_mmu.h @@ -77,13 +77,16 @@ .align 4 1: movi a2, 0x10000000 - movi a3, 0x18000000 - add a2, a2, a0 -9: bgeu a2, a3, 9b /* PC is out of the expected range */ + +#if CONFIG_KERNEL_LOAD_ADDRESS < 0x40000000ul +#define TEMP_MAPPING_VADDR 0x40000000 +#else +#define TEMP_MAPPING_VADDR 0x00000000 +#endif /* Step 1: invalidate mapping at 0x40000000..0x5FFFFFFF. */ - movi a2, 0x40000000 | XCHAL_SPANNING_WAY + movi a2, TEMP_MAPPING_VADDR | XCHAL_SPANNING_WAY idtlb a2 iitlb a2 isync @@ -95,14 +98,14 @@ srli a3, a0, 27 slli a3, a3, 27 addi a3, a3, CA_BYPASS - addi a7, a2, -1 + addi a7, a2, 5 - XCHAL_SPANNING_WAY wdtlb a3, a7 witlb a3, a7 isync slli a4, a0, 5 srli a4, a4, 5 - addi a5, a2, -6 + addi a5, a2, -XCHAL_SPANNING_WAY add a4, a4, a5 jx a4 @@ -116,35 +119,48 @@ add a5, a5, a4 bne a5, a2, 3b - /* Step 4: Setup MMU with the old V2 mappings. */ + /* Step 4: Setup MMU with the requested static mappings. */ + movi a6, 0x01000000 wsr a6, ITLBCFG wsr a6, DTLBCFG isync - movi a5, 0xd0000005 - movi a4, CA_WRITEBACK + movi a5, XCHAL_KSEG_CACHED_VADDR + XCHAL_KSEG_TLB_WAY + movi a4, XCHAL_KSEG_PADDR + CA_WRITEBACK wdtlb a4, a5 witlb a4, a5 - movi a5, 0xd8000005 - movi a4, CA_BYPASS + movi a5, XCHAL_KSEG_BYPASS_VADDR + XCHAL_KSEG_TLB_WAY + movi a4, XCHAL_KSEG_PADDR + CA_BYPASS wdtlb a4, a5 witlb a4, a5 - movi a5, XCHAL_KIO_CACHED_VADDR + 6 +#ifdef CONFIG_XTENSA_KSEG_512M + movi a5, XCHAL_KSEG_CACHED_VADDR + 0x10000000 + XCHAL_KSEG_TLB_WAY + movi a4, XCHAL_KSEG_PADDR + 0x10000000 + CA_WRITEBACK + wdtlb a4, a5 + witlb a4, a5 + + movi a5, XCHAL_KSEG_BYPASS_VADDR + 0x10000000 + XCHAL_KSEG_TLB_WAY + movi a4, XCHAL_KSEG_PADDR + 0x10000000 + CA_BYPASS + wdtlb a4, a5 + witlb a4, a5 +#endif + + movi a5, XCHAL_KIO_CACHED_VADDR + XCHAL_KIO_TLB_WAY movi a4, XCHAL_KIO_DEFAULT_PADDR + CA_WRITEBACK wdtlb a4, a5 witlb a4, a5 - movi a5, XCHAL_KIO_BYPASS_VADDR + 6 + movi a5, XCHAL_KIO_BYPASS_VADDR + XCHAL_KIO_TLB_WAY movi a4, XCHAL_KIO_DEFAULT_PADDR + CA_BYPASS wdtlb a4, a5 witlb a4, a5 isync - /* Jump to self, using MMU v2 mappings. */ + /* Jump to self, using final mappings. */ movi a4, 1f jx a4 diff --git a/arch/xtensa/include/asm/kmem_layout.h b/arch/xtensa/include/asm/kmem_layout.h new file mode 100644 index 0000000000000000000000000000000000000000..561f8729bcde96809d647efb6a01dfc031243117 --- /dev/null +++ b/arch/xtensa/include/asm/kmem_layout.h @@ -0,0 +1,74 @@ +/* + * Kernel virtual memory layout definitions. + * + * This file is subject to the terms and conditions of the GNU General + * Public License. See the file "COPYING" in the main directory of + * this archive for more details. + * + * Copyright (C) 2016 Cadence Design Systems Inc. + */ + +#ifndef _XTENSA_KMEM_LAYOUT_H +#define _XTENSA_KMEM_LAYOUT_H + +#include + +#ifdef CONFIG_MMU + +/* + * Fixed TLB translations in the processor. + */ + +#define XCHAL_PAGE_TABLE_VADDR __XTENSA_UL_CONST(0x80000000) +#define XCHAL_PAGE_TABLE_SIZE __XTENSA_UL_CONST(0x00400000) + +#if defined(CONFIG_XTENSA_KSEG_MMU_V2) + +#define XCHAL_KSEG_CACHED_VADDR __XTENSA_UL_CONST(0xd0000000) +#define XCHAL_KSEG_BYPASS_VADDR __XTENSA_UL_CONST(0xd8000000) +#define XCHAL_KSEG_SIZE __XTENSA_UL_CONST(0x08000000) +#define XCHAL_KSEG_ALIGNMENT __XTENSA_UL_CONST(0x08000000) +#define XCHAL_KSEG_TLB_WAY 5 +#define XCHAL_KIO_TLB_WAY 6 + +#elif defined(CONFIG_XTENSA_KSEG_256M) + +#define XCHAL_KSEG_CACHED_VADDR __XTENSA_UL_CONST(0xb0000000) +#define XCHAL_KSEG_BYPASS_VADDR __XTENSA_UL_CONST(0xc0000000) +#define XCHAL_KSEG_SIZE __XTENSA_UL_CONST(0x10000000) +#define XCHAL_KSEG_ALIGNMENT __XTENSA_UL_CONST(0x10000000) +#define XCHAL_KSEG_TLB_WAY 6 +#define XCHAL_KIO_TLB_WAY 6 + +#elif defined(CONFIG_XTENSA_KSEG_512M) + +#define XCHAL_KSEG_CACHED_VADDR __XTENSA_UL_CONST(0xa0000000) +#define XCHAL_KSEG_BYPASS_VADDR __XTENSA_UL_CONST(0xc0000000) +#define XCHAL_KSEG_SIZE __XTENSA_UL_CONST(0x20000000) +#define XCHAL_KSEG_ALIGNMENT __XTENSA_UL_CONST(0x10000000) +#define XCHAL_KSEG_TLB_WAY 6 +#define XCHAL_KIO_TLB_WAY 6 + +#else +#error Unsupported KSEG configuration +#endif + +#ifdef CONFIG_KSEG_PADDR +#define XCHAL_KSEG_PADDR __XTENSA_UL_CONST(CONFIG_KSEG_PADDR) +#else +#define XCHAL_KSEG_PADDR __XTENSA_UL_CONST(0x00000000) +#endif + +#if XCHAL_KSEG_PADDR & (XCHAL_KSEG_ALIGNMENT - 1) +#error XCHAL_KSEG_PADDR is not properly aligned to XCHAL_KSEG_ALIGNMENT +#endif + +#else + +#define XCHAL_KSEG_CACHED_VADDR __XTENSA_UL_CONST(0xd0000000) +#define XCHAL_KSEG_BYPASS_VADDR __XTENSA_UL_CONST(0xd8000000) +#define XCHAL_KSEG_SIZE __XTENSA_UL_CONST(0x08000000) + +#endif + +#endif diff --git a/arch/xtensa/include/asm/page.h b/arch/xtensa/include/asm/page.h index ad38500471fa314fdef56b1aef6d1ad72578b9d7..976b1d70edbc0a2d77016409fec93ec597df9cad 100644 --- a/arch/xtensa/include/asm/page.h +++ b/arch/xtensa/include/asm/page.h @@ -15,15 +15,7 @@ #include #include #include - -/* - * Fixed TLB translations in the processor. - */ - -#define XCHAL_KSEG_CACHED_VADDR __XTENSA_UL_CONST(0xd0000000) -#define XCHAL_KSEG_BYPASS_VADDR __XTENSA_UL_CONST(0xd8000000) -#define XCHAL_KSEG_PADDR __XTENSA_UL_CONST(0x00000000) -#define XCHAL_KSEG_SIZE __XTENSA_UL_CONST(0x08000000) +#include /* * PAGE_SHIFT determines the page size @@ -35,10 +27,13 @@ #ifdef CONFIG_MMU #define PAGE_OFFSET XCHAL_KSEG_CACHED_VADDR -#define MAX_MEM_PFN XCHAL_KSEG_SIZE +#define PHYS_OFFSET XCHAL_KSEG_PADDR +#define MAX_LOW_PFN (PHYS_PFN(XCHAL_KSEG_PADDR) + \ + PHYS_PFN(XCHAL_KSEG_SIZE)) #else -#define PAGE_OFFSET __XTENSA_UL_CONST(0) -#define MAX_MEM_PFN (PLATFORM_DEFAULT_MEM_START + PLATFORM_DEFAULT_MEM_SIZE) +#define PAGE_OFFSET PLATFORM_DEFAULT_MEM_START +#define PHYS_OFFSET PLATFORM_DEFAULT_MEM_START +#define MAX_LOW_PFN PHYS_PFN(0xfffffffful) #endif #define PGTABLE_START 0x80000000 @@ -167,10 +162,12 @@ void copy_user_highpage(struct page *to, struct page *from, * addresses. */ -#define ARCH_PFN_OFFSET (PLATFORM_DEFAULT_MEM_START >> PAGE_SHIFT) +#define ARCH_PFN_OFFSET (PHYS_OFFSET >> PAGE_SHIFT) -#define __pa(x) ((unsigned long) (x) - PAGE_OFFSET) -#define __va(x) ((void *)((unsigned long) (x) + PAGE_OFFSET)) +#define __pa(x) \ + ((unsigned long) (x) - PAGE_OFFSET + PHYS_OFFSET) +#define __va(x) \ + ((void *)((unsigned long) (x) - PHYS_OFFSET + PAGE_OFFSET)) #define pfn_valid(pfn) \ ((pfn) >= ARCH_PFN_OFFSET && ((pfn) - ARCH_PFN_OFFSET) < max_mapnr) diff --git a/arch/xtensa/include/asm/pgtable.h b/arch/xtensa/include/asm/pgtable.h index fb02fdc5eceee5c07e262e01826c23fcd5907646..8aa0e0d9cbb21f0c3703192a828dbbeaf4d475ca 100644 --- a/arch/xtensa/include/asm/pgtable.h +++ b/arch/xtensa/include/asm/pgtable.h @@ -13,6 +13,7 @@ #include #include +#include /* * We only use two ring levels, user and kernel space. @@ -68,9 +69,9 @@ * Virtual memory area. We keep a distance to other memory regions to be * on the safe side. We also use this area for cache aliasing. */ -#define VMALLOC_START 0xC0000000 -#define VMALLOC_END 0xC7FEFFFF -#define TLBTEMP_BASE_1 0xC7FF0000 +#define VMALLOC_START (XCHAL_KSEG_CACHED_VADDR - 0x10000000) +#define VMALLOC_END (VMALLOC_START + 0x07FEFFFF) +#define TLBTEMP_BASE_1 (VMALLOC_END + 1) #define TLBTEMP_BASE_2 (TLBTEMP_BASE_1 + DCACHE_WAY_SIZE) #if 2 * DCACHE_WAY_SIZE > ICACHE_WAY_SIZE #define TLBTEMP_SIZE (2 * DCACHE_WAY_SIZE) diff --git a/arch/xtensa/include/asm/platform.h b/arch/xtensa/include/asm/platform.h index 32e98f27ce9797cc6b82427ce9e98a3083158794..f8fbef67bc5f20590df28e635950faeecce521e2 100644 --- a/arch/xtensa/include/asm/platform.h +++ b/arch/xtensa/include/asm/platform.h @@ -69,4 +69,10 @@ extern int platform_pcibios_fixup (void); */ extern void platform_calibrate_ccount (void); +/* + * Flush and reset the mmu, simulate a processor reset, and + * jump to the reset vector. + */ +void cpu_reset(void) __attribute__((noreturn)); + #endif /* _XTENSA_PLATFORM_H */ diff --git a/arch/xtensa/include/asm/processor.h b/arch/xtensa/include/asm/processor.h index d2e40d39c6158102de48debffe76a0c5fe4f4cbc..b42d68bfe3cf0a965380bef7aae9afdcdada8050 100644 --- a/arch/xtensa/include/asm/processor.h +++ b/arch/xtensa/include/asm/processor.h @@ -37,7 +37,7 @@ #ifdef CONFIG_MMU #define TASK_SIZE __XTENSA_UL_CONST(0x40000000) #else -#define TASK_SIZE (PLATFORM_DEFAULT_MEM_START + PLATFORM_DEFAULT_MEM_SIZE) +#define TASK_SIZE __XTENSA_UL_CONST(0xffffffff) #endif #define STACK_TOP TASK_SIZE diff --git a/arch/xtensa/include/asm/sysmem.h b/arch/xtensa/include/asm/sysmem.h index c015c5c8e3f70f186450ff9bb3ada372c41f213a..552cdfd8590efb2df4fffd7acc6cb0a5ef75da0e 100644 --- a/arch/xtensa/include/asm/sysmem.h +++ b/arch/xtensa/include/asm/sysmem.h @@ -11,27 +11,8 @@ #ifndef _XTENSA_SYSMEM_H #define _XTENSA_SYSMEM_H -#define SYSMEM_BANKS_MAX 31 +#include -struct meminfo { - unsigned long start; - unsigned long end; -}; - -/* - * Bank array is sorted by .start. - * Banks don't overlap and there's at least one page gap - * between adjacent bank entries. - */ -struct sysmem_info { - int nr_banks; - struct meminfo bank[SYSMEM_BANKS_MAX]; -}; - -extern struct sysmem_info sysmem; - -int add_sysmem_bank(unsigned long start, unsigned long end); -int mem_reserve(unsigned long, unsigned long, int); void bootmem_init(void); void zones_init(void); diff --git a/arch/xtensa/include/asm/vectors.h b/arch/xtensa/include/asm/vectors.h index 288c776736d3163640b48b080a50eecb0fd17f00..77d41cc7a688ac0b2a4c8239231a7edd75c3ff34 100644 --- a/arch/xtensa/include/asm/vectors.h +++ b/arch/xtensa/include/asm/vectors.h @@ -20,6 +20,7 @@ #include #include +#include #if XCHAL_HAVE_PTP_MMU #define XCHAL_KIO_CACHED_VADDR 0xe0000000 @@ -47,61 +48,42 @@ static inline unsigned long xtensa_get_kio_paddr(void) #if defined(CONFIG_MMU) -/* Will Become VECBASE */ -#define VIRTUAL_MEMORY_ADDRESS 0xD0000000 - +#if XCHAL_HAVE_PTP_MMU && XCHAL_HAVE_SPANNING_WAY /* Image Virtual Start Address */ -#define KERNELOFFSET 0xD0003000 - -#if defined(XCHAL_HAVE_PTP_MMU) && XCHAL_HAVE_PTP_MMU && XCHAL_HAVE_SPANNING_WAY - /* MMU v3 - XCHAL_HAVE_PTP_MMU == 1 */ - #define LOAD_MEMORY_ADDRESS 0x00003000 +#define KERNELOFFSET (XCHAL_KSEG_CACHED_VADDR + \ + CONFIG_KERNEL_LOAD_ADDRESS - \ + XCHAL_KSEG_PADDR) #else - /* MMU V2 - XCHAL_HAVE_PTP_MMU == 0 */ - #define LOAD_MEMORY_ADDRESS 0xD0003000 +#define KERNELOFFSET CONFIG_KERNEL_LOAD_ADDRESS #endif -#define RESET_VECTOR1_VADDR (VIRTUAL_MEMORY_ADDRESS + \ - XCHAL_RESET_VECTOR1_PADDR) - #else /* !defined(CONFIG_MMU) */ /* MMU Not being used - Virtual == Physical */ - /* VECBASE */ - #define VIRTUAL_MEMORY_ADDRESS (PLATFORM_DEFAULT_MEM_START + 0x2000) +/* Location of the start of the kernel text, _start */ +#define KERNELOFFSET CONFIG_KERNEL_LOAD_ADDRESS - /* Location of the start of the kernel text, _start */ - #define KERNELOFFSET (PLATFORM_DEFAULT_MEM_START + 0x3000) - - /* Loaded just above possibly live vectors */ - #define LOAD_MEMORY_ADDRESS (PLATFORM_DEFAULT_MEM_START + 0x3000) - -#define RESET_VECTOR1_VADDR (XCHAL_RESET_VECTOR1_VADDR) #endif /* CONFIG_MMU */ -#define XC_VADDR(offset) (VIRTUAL_MEMORY_ADDRESS + offset) - -/* Used to set VECBASE register */ -#define VECBASE_RESET_VADDR VIRTUAL_MEMORY_ADDRESS +#define RESET_VECTOR1_VADDR (XCHAL_RESET_VECTOR1_VADDR) +#define VECBASE_VADDR (KERNELOFFSET - CONFIG_VECTORS_OFFSET) #if defined(XCHAL_HAVE_VECBASE) && XCHAL_HAVE_VECBASE -#define USER_VECTOR_VADDR XC_VADDR(XCHAL_USER_VECOFS) -#define KERNEL_VECTOR_VADDR XC_VADDR(XCHAL_KERNEL_VECOFS) -#define DOUBLEEXC_VECTOR_VADDR XC_VADDR(XCHAL_DOUBLEEXC_VECOFS) -#define WINDOW_VECTORS_VADDR XC_VADDR(XCHAL_WINDOW_OF4_VECOFS) -#define INTLEVEL2_VECTOR_VADDR XC_VADDR(XCHAL_INTLEVEL2_VECOFS) -#define INTLEVEL3_VECTOR_VADDR XC_VADDR(XCHAL_INTLEVEL3_VECOFS) -#define INTLEVEL4_VECTOR_VADDR XC_VADDR(XCHAL_INTLEVEL4_VECOFS) -#define INTLEVEL5_VECTOR_VADDR XC_VADDR(XCHAL_INTLEVEL5_VECOFS) -#define INTLEVEL6_VECTOR_VADDR XC_VADDR(XCHAL_INTLEVEL6_VECOFS) - -#define DEBUG_VECTOR_VADDR XC_VADDR(XCHAL_DEBUG_VECOFS) +#define VECTOR_VADDR(offset) (VECBASE_VADDR + offset) -#define NMI_VECTOR_VADDR XC_VADDR(XCHAL_NMI_VECOFS) - -#define INTLEVEL7_VECTOR_VADDR XC_VADDR(XCHAL_INTLEVEL7_VECOFS) +#define USER_VECTOR_VADDR VECTOR_VADDR(XCHAL_USER_VECOFS) +#define KERNEL_VECTOR_VADDR VECTOR_VADDR(XCHAL_KERNEL_VECOFS) +#define DOUBLEEXC_VECTOR_VADDR VECTOR_VADDR(XCHAL_DOUBLEEXC_VECOFS) +#define WINDOW_VECTORS_VADDR VECTOR_VADDR(XCHAL_WINDOW_OF4_VECOFS) +#define INTLEVEL2_VECTOR_VADDR VECTOR_VADDR(XCHAL_INTLEVEL2_VECOFS) +#define INTLEVEL3_VECTOR_VADDR VECTOR_VADDR(XCHAL_INTLEVEL3_VECOFS) +#define INTLEVEL4_VECTOR_VADDR VECTOR_VADDR(XCHAL_INTLEVEL4_VECOFS) +#define INTLEVEL5_VECTOR_VADDR VECTOR_VADDR(XCHAL_INTLEVEL5_VECOFS) +#define INTLEVEL6_VECTOR_VADDR VECTOR_VADDR(XCHAL_INTLEVEL6_VECOFS) +#define INTLEVEL7_VECTOR_VADDR VECTOR_VADDR(XCHAL_INTLEVEL7_VECOFS) +#define DEBUG_VECTOR_VADDR VECTOR_VADDR(XCHAL_DEBUG_VECOFS) /* * These XCHAL_* #defines from varian/core.h @@ -109,7 +91,6 @@ static inline unsigned long xtensa_get_kio_paddr(void) * constants are defined above and should be used. */ #undef XCHAL_VECBASE_RESET_VADDR -#undef XCHAL_RESET_VECTOR0_VADDR #undef XCHAL_USER_VECTOR_VADDR #undef XCHAL_KERNEL_VECTOR_VADDR #undef XCHAL_DOUBLEEXC_VECTOR_VADDR @@ -119,9 +100,8 @@ static inline unsigned long xtensa_get_kio_paddr(void) #undef XCHAL_INTLEVEL4_VECTOR_VADDR #undef XCHAL_INTLEVEL5_VECTOR_VADDR #undef XCHAL_INTLEVEL6_VECTOR_VADDR -#undef XCHAL_DEBUG_VECTOR_VADDR -#undef XCHAL_NMI_VECTOR_VADDR #undef XCHAL_INTLEVEL7_VECTOR_VADDR +#undef XCHAL_DEBUG_VECTOR_VADDR #else @@ -134,6 +114,7 @@ static inline unsigned long xtensa_get_kio_paddr(void) #define INTLEVEL4_VECTOR_VADDR XCHAL_INTLEVEL4_VECTOR_VADDR #define INTLEVEL5_VECTOR_VADDR XCHAL_INTLEVEL5_VECTOR_VADDR #define INTLEVEL6_VECTOR_VADDR XCHAL_INTLEVEL6_VECTOR_VADDR +#define INTLEVEL7_VECTOR_VADDR XCHAL_INTLEVEL6_VECTOR_VADDR #define DEBUG_VECTOR_VADDR XCHAL_DEBUG_VECTOR_VADDR #endif diff --git a/arch/xtensa/include/uapi/asm/types.h b/arch/xtensa/include/uapi/asm/types.h index 87ec7ae73cb1a1a3ca5390ef1ab9da4e35cd107c..2efc921506c4b277253e111f0fb45d1bab458369 100644 --- a/arch/xtensa/include/uapi/asm/types.h +++ b/arch/xtensa/include/uapi/asm/types.h @@ -18,7 +18,8 @@ # define __XTENSA_UL_CONST(x) x #else # define __XTENSA_UL(x) ((unsigned long)(x)) -# define __XTENSA_UL_CONST(x) x##UL +# define ___XTENSA_UL_CONST(x) x##UL +# define __XTENSA_UL_CONST(x) ___XTENSA_UL_CONST(x) #endif #ifndef __ASSEMBLY__ diff --git a/arch/xtensa/include/uapi/asm/unistd.h b/arch/xtensa/include/uapi/asm/unistd.h index b95c30594355a47b507f25ba0e45a043755a5502..de9b14b2d348b84ea078e412d3d9f3883e444cb4 100644 --- a/arch/xtensa/include/uapi/asm/unistd.h +++ b/arch/xtensa/include/uapi/asm/unistd.h @@ -754,7 +754,20 @@ __SYSCALL(340, sys_bpf, 3) #define __NR_execveat 341 __SYSCALL(341, sys_execveat, 5) -#define __NR_syscall_count 342 +#define __NR_userfaultfd 342 +__SYSCALL(342, sys_userfaultfd, 1) +#define __NR_membarrier 343 +__SYSCALL(343, sys_membarrier, 2) +#define __NR_mlock2 344 +__SYSCALL(344, sys_mlock2, 3) +#define __NR_copy_file_range 345 +__SYSCALL(345, sys_copy_file_range, 6) +#define __NR_preadv2 346 +__SYSCALL(346, sys_preadv2, 6) +#define __NR_pwritev2 347 +__SYSCALL(347, sys_pwritev2, 6) + +#define __NR_syscall_count 348 /* * sysxtensa syscall handler diff --git a/arch/xtensa/kernel/entry.S b/arch/xtensa/kernel/entry.S index fe8f7e7efb9dc180c12bcfa0cedb6f4d0f59366f..fa04d9d368a7218d488874934aad4429e93a927f 100644 --- a/arch/xtensa/kernel/entry.S +++ b/arch/xtensa/kernel/entry.S @@ -1632,10 +1632,11 @@ ENTRY(fast_second_level_miss) * The messy computation for 'pteval' above really simplifies * into the following: * - * pteval = ((pmdval - PAGE_OFFSET) & PAGE_MASK) | PAGE_DIRECTORY + * pteval = ((pmdval - PAGE_OFFSET + PHYS_OFFSET) & PAGE_MASK) + * | PAGE_DIRECTORY */ - movi a1, (-PAGE_OFFSET) & 0xffffffff + movi a1, (PHYS_OFFSET - PAGE_OFFSET) & 0xffffffff add a0, a0, a1 # pmdval - PAGE_OFFSET extui a1, a0, 0, PAGE_SHIFT # ... & PAGE_MASK xor a0, a0, a1 diff --git a/arch/xtensa/kernel/head.S b/arch/xtensa/kernel/head.S index bc4f4bf050999d7694a711341d5fe75800896e7f..23ce62e604359d01fe8be9f41df9d1914ae90796 100644 --- a/arch/xtensa/kernel/head.S +++ b/arch/xtensa/kernel/head.S @@ -113,7 +113,7 @@ ENTRY(_startup) movi a0, 0 #if XCHAL_HAVE_VECBASE - movi a2, VECBASE_RESET_VADDR + movi a2, VECBASE_VADDR wsr a2, vecbase #endif diff --git a/arch/xtensa/kernel/setup.c b/arch/xtensa/kernel/setup.c index 143251ede89784792258469e610e4eb6b0dc6546..88a044af7504dd9c47d0f97d64620ac8de4b5739 100644 --- a/arch/xtensa/kernel/setup.c +++ b/arch/xtensa/kernel/setup.c @@ -7,6 +7,7 @@ * * Copyright (C) 1995 Linus Torvalds * Copyright (C) 2001 - 2005 Tensilica Inc. + * Copyright (C) 2014 - 2016 Cadence Design Systems Inc. * * Chris Zankel * Joe Taylor @@ -22,7 +23,6 @@ #include #include #include -#include #include #include #include @@ -114,7 +114,7 @@ static int __init parse_tag_mem(const bp_tag_t *tag) if (mi->type != MEMORY_TYPE_CONVENTIONAL) return -1; - return add_sysmem_bank(mi->start, mi->end); + return memblock_add(mi->start, mi->end - mi->start); } __tagtable(BP_TAG_MEMORY, parse_tag_mem); @@ -188,7 +188,6 @@ static int __init parse_bootparam(const bp_tag_t* tag) } #ifdef CONFIG_OF -bool __initdata dt_memory_scan = false; #if !XCHAL_HAVE_PTP_MMU || XCHAL_HAVE_SPANNING_WAY unsigned long xtensa_kio_paddr = XCHAL_KIO_DEFAULT_PADDR; @@ -228,11 +227,8 @@ static int __init xtensa_dt_io_area(unsigned long node, const char *uname, void __init early_init_dt_add_memory_arch(u64 base, u64 size) { - if (!dt_memory_scan) - return; - size &= PAGE_MASK; - add_sysmem_bank(base, base + size); + memblock_add(base, size); } void * __init early_init_dt_alloc_memory_arch(u64 size, u64 align) @@ -242,9 +238,6 @@ void * __init early_init_dt_alloc_memory_arch(u64 size, u64 align) void __init early_init_devtree(void *params) { - if (sysmem.nr_banks == 0) - dt_memory_scan = true; - early_init_dt_scan(params); of_scan_flat_dt(xtensa_dt_io_area, NULL); @@ -252,14 +245,6 @@ void __init early_init_devtree(void *params) strlcpy(command_line, boot_command_line, COMMAND_LINE_SIZE); } -static int __init xtensa_device_probe(void) -{ - of_clk_init(NULL); - return 0; -} - -device_initcall(xtensa_device_probe); - #endif /* CONFIG_OF */ /* @@ -277,12 +262,6 @@ void __init init_arch(bp_tag_t *bp_start) early_init_devtree(dtb_start); #endif - if (sysmem.nr_banks == 0) { - add_sysmem_bank(PLATFORM_DEFAULT_MEM_START, - PLATFORM_DEFAULT_MEM_START + - PLATFORM_DEFAULT_MEM_SIZE); - } - #ifdef CONFIG_CMDLINE_BOOL if (!command_line[0]) strlcpy(command_line, default_command_line, COMMAND_LINE_SIZE); @@ -452,6 +431,10 @@ static int __init check_s32c1i(void) early_initcall(check_s32c1i); #endif /* CONFIG_S32C1I_SELFTEST */ +static inline int mem_reserve(unsigned long start, unsigned long end) +{ + return memblock_reserve(start, end - start); +} void __init setup_arch(char **cmdline_p) { @@ -463,54 +446,54 @@ void __init setup_arch(char **cmdline_p) #ifdef CONFIG_BLK_DEV_INITRD if (initrd_start < initrd_end) { initrd_is_mapped = mem_reserve(__pa(initrd_start), - __pa(initrd_end), 0) == 0; + __pa(initrd_end)) == 0; initrd_below_start_ok = 1; } else { initrd_start = 0; } #endif - mem_reserve(__pa(&_stext),__pa(&_end), 1); + mem_reserve(__pa(&_stext), __pa(&_end)); mem_reserve(__pa(&_WindowVectors_text_start), - __pa(&_WindowVectors_text_end), 0); + __pa(&_WindowVectors_text_end)); mem_reserve(__pa(&_DebugInterruptVector_literal_start), - __pa(&_DebugInterruptVector_text_end), 0); + __pa(&_DebugInterruptVector_text_end)); mem_reserve(__pa(&_KernelExceptionVector_literal_start), - __pa(&_KernelExceptionVector_text_end), 0); + __pa(&_KernelExceptionVector_text_end)); mem_reserve(__pa(&_UserExceptionVector_literal_start), - __pa(&_UserExceptionVector_text_end), 0); + __pa(&_UserExceptionVector_text_end)); mem_reserve(__pa(&_DoubleExceptionVector_literal_start), - __pa(&_DoubleExceptionVector_text_end), 0); + __pa(&_DoubleExceptionVector_text_end)); #if XCHAL_EXCM_LEVEL >= 2 mem_reserve(__pa(&_Level2InterruptVector_text_start), - __pa(&_Level2InterruptVector_text_end), 0); + __pa(&_Level2InterruptVector_text_end)); #endif #if XCHAL_EXCM_LEVEL >= 3 mem_reserve(__pa(&_Level3InterruptVector_text_start), - __pa(&_Level3InterruptVector_text_end), 0); + __pa(&_Level3InterruptVector_text_end)); #endif #if XCHAL_EXCM_LEVEL >= 4 mem_reserve(__pa(&_Level4InterruptVector_text_start), - __pa(&_Level4InterruptVector_text_end), 0); + __pa(&_Level4InterruptVector_text_end)); #endif #if XCHAL_EXCM_LEVEL >= 5 mem_reserve(__pa(&_Level5InterruptVector_text_start), - __pa(&_Level5InterruptVector_text_end), 0); + __pa(&_Level5InterruptVector_text_end)); #endif #if XCHAL_EXCM_LEVEL >= 6 mem_reserve(__pa(&_Level6InterruptVector_text_start), - __pa(&_Level6InterruptVector_text_end), 0); + __pa(&_Level6InterruptVector_text_end)); #endif #ifdef CONFIG_SMP mem_reserve(__pa(&_SecondaryResetVector_text_start), - __pa(&_SecondaryResetVector_text_end), 0); + __pa(&_SecondaryResetVector_text_end)); #endif parse_early_param(); bootmem_init(); @@ -555,6 +538,137 @@ static int __init topology_init(void) } subsys_initcall(topology_init); +void cpu_reset(void) +{ +#if XCHAL_HAVE_PTP_MMU + local_irq_disable(); + /* + * We have full MMU: all autoload ways, ways 7, 8 and 9 of DTLB must + * be flushed. + * Way 4 is not currently used by linux. + * Ways 5 and 6 shall not be touched on MMUv2 as they are hardwired. + * Way 5 shall be flushed and way 6 shall be set to identity mapping + * on MMUv3. + */ + local_flush_tlb_all(); + invalidate_page_directory(); +#if XCHAL_HAVE_SPANNING_WAY + /* MMU v3 */ + { + unsigned long vaddr = (unsigned long)cpu_reset; + unsigned long paddr = __pa(vaddr); + unsigned long tmpaddr = vaddr + SZ_512M; + unsigned long tmp0, tmp1, tmp2, tmp3; + + /* + * Find a place for the temporary mapping. It must not be + * in the same 512MB region with vaddr or paddr, otherwise + * there may be multihit exception either on entry to the + * temporary mapping, or on entry to the identity mapping. + * (512MB is the biggest page size supported by TLB.) + */ + while (((tmpaddr ^ paddr) & -SZ_512M) == 0) + tmpaddr += SZ_512M; + + /* Invalidate mapping in the selected temporary area */ + if (itlb_probe(tmpaddr) & 0x8) + invalidate_itlb_entry(itlb_probe(tmpaddr)); + if (itlb_probe(tmpaddr + PAGE_SIZE) & 0x8) + invalidate_itlb_entry(itlb_probe(tmpaddr + PAGE_SIZE)); + + /* + * Map two consecutive pages starting at the physical address + * of this function to the temporary mapping area. + */ + write_itlb_entry(__pte((paddr & PAGE_MASK) | + _PAGE_HW_VALID | + _PAGE_HW_EXEC | + _PAGE_CA_BYPASS), + tmpaddr & PAGE_MASK); + write_itlb_entry(__pte(((paddr & PAGE_MASK) + PAGE_SIZE) | + _PAGE_HW_VALID | + _PAGE_HW_EXEC | + _PAGE_CA_BYPASS), + (tmpaddr & PAGE_MASK) + PAGE_SIZE); + + /* Reinitialize TLB */ + __asm__ __volatile__ ("movi %0, 1f\n\t" + "movi %3, 2f\n\t" + "add %0, %0, %4\n\t" + "add %3, %3, %5\n\t" + "jx %0\n" + /* + * No literal, data or stack access + * below this point + */ + "1:\n\t" + /* Initialize *tlbcfg */ + "movi %0, 0\n\t" + "wsr %0, itlbcfg\n\t" + "wsr %0, dtlbcfg\n\t" + /* Invalidate TLB way 5 */ + "movi %0, 4\n\t" + "movi %1, 5\n" + "1:\n\t" + "iitlb %1\n\t" + "idtlb %1\n\t" + "add %1, %1, %6\n\t" + "addi %0, %0, -1\n\t" + "bnez %0, 1b\n\t" + /* Initialize TLB way 6 */ + "movi %0, 7\n\t" + "addi %1, %9, 3\n\t" + "addi %2, %9, 6\n" + "1:\n\t" + "witlb %1, %2\n\t" + "wdtlb %1, %2\n\t" + "add %1, %1, %7\n\t" + "add %2, %2, %7\n\t" + "addi %0, %0, -1\n\t" + "bnez %0, 1b\n\t" + /* Jump to identity mapping */ + "jx %3\n" + "2:\n\t" + /* Complete way 6 initialization */ + "witlb %1, %2\n\t" + "wdtlb %1, %2\n\t" + /* Invalidate temporary mapping */ + "sub %0, %9, %7\n\t" + "iitlb %0\n\t" + "add %0, %0, %8\n\t" + "iitlb %0" + : "=&a"(tmp0), "=&a"(tmp1), "=&a"(tmp2), + "=&a"(tmp3) + : "a"(tmpaddr - vaddr), + "a"(paddr - vaddr), + "a"(SZ_128M), "a"(SZ_512M), + "a"(PAGE_SIZE), + "a"((tmpaddr + SZ_512M) & PAGE_MASK) + : "memory"); + } +#endif +#endif + __asm__ __volatile__ ("movi a2, 0\n\t" + "wsr a2, icountlevel\n\t" + "movi a2, 0\n\t" + "wsr a2, icount\n\t" +#if XCHAL_NUM_IBREAK > 0 + "wsr a2, ibreakenable\n\t" +#endif +#if XCHAL_HAVE_LOOPS + "wsr a2, lcount\n\t" +#endif + "movi a2, 0x1f\n\t" + "wsr a2, ps\n\t" + "isync\n\t" + "jx %0\n\t" + : + : "a" (XCHAL_RESET_VECTOR_VADDR) + : "a2"); + for (;;) + ; +} + void machine_restart(char * cmd) { platform_restart(); diff --git a/arch/xtensa/kernel/time.c b/arch/xtensa/kernel/time.c index b9ad9feadc2d1a01da539d69fa735ebb61f607f2..9a5bcd0381a71e987b29499d194061af8a1b2d22 100644 --- a/arch/xtensa/kernel/time.c +++ b/arch/xtensa/kernel/time.c @@ -12,6 +12,8 @@ * Chris Zankel */ +#include +#include #include #include #include @@ -134,16 +136,52 @@ void local_timer_setup(unsigned cpu) 0xf, 0xffffffff); } +#ifdef CONFIG_XTENSA_CALIBRATE_CCOUNT +#ifdef CONFIG_OF +static void __init calibrate_ccount(void) +{ + struct device_node *cpu; + struct clk *clk; + + cpu = of_find_compatible_node(NULL, NULL, "cdns,xtensa-cpu"); + if (cpu) { + clk = of_clk_get(cpu, 0); + if (!IS_ERR(clk)) { + ccount_freq = clk_get_rate(clk); + return; + } else { + pr_warn("%s: CPU input clock not found\n", + __func__); + } + } else { + pr_warn("%s: CPU node not found in the device tree\n", + __func__); + } + + platform_calibrate_ccount(); +} +#else +static inline void calibrate_ccount(void) +{ + platform_calibrate_ccount(); +} +#endif +#endif + void __init time_init(void) { + of_clk_init(NULL); #ifdef CONFIG_XTENSA_CALIBRATE_CCOUNT printk("Calibrating CPU frequency "); - platform_calibrate_ccount(); + calibrate_ccount(); printk("%d.%02d MHz\n", (int)ccount_freq/1000000, (int)(ccount_freq/10000)%100); #else ccount_freq = CONFIG_XTENSA_CPU_CLOCK*1000000UL; #endif + WARN(!ccount_freq, + "%s: CPU clock frequency is not set up correctly\n", + __func__); clocksource_register_hz(&ccount_clocksource, ccount_freq); local_timer_setup(0); setup_irq(this_cpu_ptr(&ccount_timer)->evt.irq, &timer_irqaction); diff --git a/arch/xtensa/kernel/vmlinux.lds.S b/arch/xtensa/kernel/vmlinux.lds.S index c417cbe4ec878bdfc9b9cc524d426b780c63030c..72cfe3587dd865c6532874dc56f012ccbb7cdc04 100644 --- a/arch/xtensa/kernel/vmlinux.lds.S +++ b/arch/xtensa/kernel/vmlinux.lds.S @@ -30,10 +30,6 @@ jiffies = jiffies_64 + 4; jiffies = jiffies_64; #endif -#ifndef KERNELOFFSET -#define KERNELOFFSET 0xd0003000 -#endif - /* Note: In the following macros, it would be nice to specify only the vector name and section kind and construct "sym" and "section" using CPP concatenation, but that does not work reliably. Concatenating a diff --git a/arch/xtensa/mm/init.c b/arch/xtensa/mm/init.c index 9a9a5935bd3673f48a93fc5e96cac7e888f03c0e..80e4cfb2471ad5af6a99433d6e8af76e16865558 100644 --- a/arch/xtensa/mm/init.c +++ b/arch/xtensa/mm/init.c @@ -8,7 +8,7 @@ * for more details. * * Copyright (C) 2001 - 2005 Tensilica Inc. - * Copyright (C) 2014 Cadence Design Systems Inc. + * Copyright (C) 2014 - 2016 Cadence Design Systems Inc. * * Chris Zankel * Joe Taylor @@ -25,284 +25,43 @@ #include #include #include +#include #include #include #include #include -struct sysmem_info sysmem __initdata; - -static void __init sysmem_dump(void) -{ - unsigned i; - - pr_debug("Sysmem:\n"); - for (i = 0; i < sysmem.nr_banks; ++i) - pr_debug(" 0x%08lx - 0x%08lx (%ldK)\n", - sysmem.bank[i].start, sysmem.bank[i].end, - (sysmem.bank[i].end - sysmem.bank[i].start) >> 10); -} - -/* - * Find bank with maximal .start such that bank.start <= start - */ -static inline struct meminfo * __init find_bank(unsigned long start) -{ - unsigned i; - struct meminfo *it = NULL; - - for (i = 0; i < sysmem.nr_banks; ++i) - if (sysmem.bank[i].start <= start) - it = sysmem.bank + i; - else - break; - return it; -} - -/* - * Move all memory banks starting at 'from' to a new place at 'to', - * adjust nr_banks accordingly. - * Both 'from' and 'to' must be inside the sysmem.bank. - * - * Returns: 0 (success), -ENOMEM (not enough space in the sysmem.bank). - */ -static int __init move_banks(struct meminfo *to, struct meminfo *from) -{ - unsigned n = sysmem.nr_banks - (from - sysmem.bank); - - if (to > from && to - from + sysmem.nr_banks > SYSMEM_BANKS_MAX) - return -ENOMEM; - if (to != from) - memmove(to, from, n * sizeof(struct meminfo)); - sysmem.nr_banks += to - from; - return 0; -} - -/* - * Add new bank to sysmem. Resulting sysmem is the union of bytes of the - * original sysmem and the new bank. - * - * Returns: 0 (success), < 0 (error) - */ -int __init add_sysmem_bank(unsigned long start, unsigned long end) -{ - unsigned i; - struct meminfo *it = NULL; - unsigned long sz; - unsigned long bank_sz = 0; - - if (start == end || - (start < end) != (PAGE_ALIGN(start) < (end & PAGE_MASK))) { - pr_warn("Ignoring small memory bank 0x%08lx size: %ld bytes\n", - start, end - start); - return -EINVAL; - } - - start = PAGE_ALIGN(start); - end &= PAGE_MASK; - sz = end - start; - - it = find_bank(start); - - if (it) - bank_sz = it->end - it->start; - - if (it && bank_sz >= start - it->start) { - if (end - it->start > bank_sz) - it->end = end; - else - return 0; - } else { - if (!it) - it = sysmem.bank; - else - ++it; - - if (it - sysmem.bank < sysmem.nr_banks && - it->start - start <= sz) { - it->start = start; - if (it->end - it->start < sz) - it->end = end; - else - return 0; - } else { - if (move_banks(it + 1, it) < 0) { - pr_warn("Ignoring memory bank 0x%08lx size %ld bytes\n", - start, end - start); - return -EINVAL; - } - it->start = start; - it->end = end; - return 0; - } - } - sz = it->end - it->start; - for (i = it + 1 - sysmem.bank; i < sysmem.nr_banks; ++i) - if (sysmem.bank[i].start - it->start <= sz) { - if (sz < sysmem.bank[i].end - it->start) - it->end = sysmem.bank[i].end; - } else { - break; - } - - move_banks(it + 1, sysmem.bank + i); - return 0; -} - -/* - * mem_reserve(start, end, must_exist) - * - * Reserve some memory from the memory pool. - * If must_exist is set and a part of the region being reserved does not exist - * memory map is not altered. - * - * Parameters: - * start Start of region, - * end End of region, - * must_exist Must exist in memory pool. - * - * Returns: - * 0 (success) - * < 0 (error) - */ - -int __init mem_reserve(unsigned long start, unsigned long end, int must_exist) -{ - struct meminfo *it; - struct meminfo *rm = NULL; - unsigned long sz; - unsigned long bank_sz = 0; - - start = start & PAGE_MASK; - end = PAGE_ALIGN(end); - sz = end - start; - if (!sz) - return -EINVAL; - - it = find_bank(start); - - if (it) - bank_sz = it->end - it->start; - - if ((!it || end - it->start > bank_sz) && must_exist) { - pr_warn("mem_reserve: [0x%0lx, 0x%0lx) not in any region!\n", - start, end); - return -EINVAL; - } - - if (it && start - it->start <= bank_sz) { - if (start == it->start) { - if (end - it->start < bank_sz) { - it->start = end; - return 0; - } else { - rm = it; - } - } else { - it->end = start; - if (end - it->start < bank_sz) - return add_sysmem_bank(end, - it->start + bank_sz); - ++it; - } - } - - if (!it) - it = sysmem.bank; - - for (; it < sysmem.bank + sysmem.nr_banks; ++it) { - if (it->end - start <= sz) { - if (!rm) - rm = it; - } else { - if (it->start - start < sz) - it->start = end; - break; - } - } - - if (rm) - move_banks(rm, it); - - return 0; -} - - /* * Initialize the bootmem system and give it all low memory we have available. */ void __init bootmem_init(void) { - unsigned long pfn; - unsigned long bootmap_start, bootmap_size; - int i; - - /* Reserve all memory below PLATFORM_DEFAULT_MEM_START, as memory + /* Reserve all memory below PHYS_OFFSET, as memory * accounting doesn't work for pages below that address. * - * If PLATFORM_DEFAULT_MEM_START is zero reserve page at address 0: + * If PHYS_OFFSET is zero reserve page at address 0: * successfull allocations should never return NULL. */ - if (PLATFORM_DEFAULT_MEM_START) - mem_reserve(0, PLATFORM_DEFAULT_MEM_START, 0); + if (PHYS_OFFSET) + memblock_reserve(0, PHYS_OFFSET); else - mem_reserve(0, 1, 0); + memblock_reserve(0, 1); - sysmem_dump(); - max_low_pfn = max_pfn = 0; - min_low_pfn = ~0; - - for (i=0; i < sysmem.nr_banks; i++) { - pfn = PAGE_ALIGN(sysmem.bank[i].start) >> PAGE_SHIFT; - if (pfn < min_low_pfn) - min_low_pfn = pfn; - pfn = PAGE_ALIGN(sysmem.bank[i].end - 1) >> PAGE_SHIFT; - if (pfn > max_pfn) - max_pfn = pfn; - } + early_init_fdt_scan_reserved_mem(); - if (min_low_pfn > max_pfn) + if (!memblock_phys_mem_size()) panic("No memory found!\n"); - max_low_pfn = max_pfn < MAX_MEM_PFN >> PAGE_SHIFT ? - max_pfn : MAX_MEM_PFN >> PAGE_SHIFT; + min_low_pfn = PFN_UP(memblock_start_of_DRAM()); + min_low_pfn = max(min_low_pfn, PFN_UP(PHYS_OFFSET)); + max_pfn = PFN_DOWN(memblock_end_of_DRAM()); + max_low_pfn = min(max_pfn, MAX_LOW_PFN); - /* Find an area to use for the bootmem bitmap. */ - - bootmap_size = bootmem_bootmap_pages(max_low_pfn - min_low_pfn); - bootmap_size <<= PAGE_SHIFT; - bootmap_start = ~0; - - for (i=0; i= bootmap_size) { - bootmap_start = sysmem.bank[i].start; - break; - } - - if (bootmap_start == ~0UL) - panic("Cannot find %ld bytes for bootmap\n", bootmap_size); - - /* Reserve the bootmem bitmap area */ - - mem_reserve(bootmap_start, bootmap_start + bootmap_size, 1); - bootmap_size = init_bootmem_node(NODE_DATA(0), - bootmap_start >> PAGE_SHIFT, - min_low_pfn, - max_low_pfn); - - /* Add all remaining memory pieces into the bootmem map */ - - for (i = 0; i < sysmem.nr_banks; i++) { - if (sysmem.bank[i].start >> PAGE_SHIFT < max_low_pfn) { - unsigned long end = min(max_low_pfn << PAGE_SHIFT, - sysmem.bank[i].end); - free_bootmem(sysmem.bank[i].start, - end - sysmem.bank[i].start); - } - } + memblock_set_current_limit(PFN_PHYS(max_low_pfn)); + memblock_dump_all(); } @@ -344,7 +103,7 @@ void __init mem_init(void) " fixmap : 0x%08lx - 0x%08lx (%5lu kB)\n" #endif #ifdef CONFIG_MMU - " vmalloc : 0x%08x - 0x%08x (%5u MB)\n" + " vmalloc : 0x%08lx - 0x%08lx (%5lu MB)\n" #endif " lowmem : 0x%08lx - 0x%08lx (%5lu MB)\n", #ifdef CONFIG_HIGHMEM @@ -395,16 +154,16 @@ static void __init parse_memmap_one(char *p) switch (*p) { case '@': start_at = memparse(p + 1, &p); - add_sysmem_bank(start_at, start_at + mem_size); + memblock_add(start_at, mem_size); break; case '$': start_at = memparse(p + 1, &p); - mem_reserve(start_at, start_at + mem_size, 0); + memblock_reserve(start_at, mem_size); break; case 0: - mem_reserve(mem_size, 0, 0); + memblock_reserve(mem_size, -mem_size); break; default: diff --git a/arch/xtensa/platforms/iss/include/platform/simcall.h b/arch/xtensa/platforms/iss/include/platform/simcall.h index 12b15ad1e5863bc28a3094c0c08721c2c2b83dc4..27d7a528b41ae53d35c9ac24f0d75b4046a7de53 100644 --- a/arch/xtensa/platforms/iss/include/platform/simcall.h +++ b/arch/xtensa/platforms/iss/include/platform/simcall.h @@ -76,6 +76,11 @@ static inline int __simc(int a, int b, int c, int d) return ret; } +static inline int simc_exit(int exit_code) +{ + return __simc(SYS_exit, exit_code, 0, 0); +} + static inline int simc_open(const char *file, int flags, int mode) { return __simc(SYS_open, (int) file, flags, mode); diff --git a/arch/xtensa/platforms/iss/setup.c b/arch/xtensa/platforms/iss/setup.c index 391820539f0ae12bea63f1327cf859357647c859..379aeddcc63886c9368bfab1d4189ef8f21837da 100644 --- a/arch/xtensa/platforms/iss/setup.c +++ b/arch/xtensa/platforms/iss/setup.c @@ -32,6 +32,8 @@ #include #include +#include + void __init platform_init(bp_tag_t* bootparam) { @@ -41,37 +43,19 @@ void __init platform_init(bp_tag_t* bootparam) void platform_halt(void) { pr_info(" ** Called platform_halt() **\n"); - __asm__ __volatile__("movi a2, 1\nsimcall\n"); + simc_exit(0); } void platform_power_off(void) { pr_info(" ** Called platform_power_off() **\n"); - __asm__ __volatile__("movi a2, 1\nsimcall\n"); + simc_exit(0); } void platform_restart(void) { /* Flush and reset the mmu, simulate a processor reset, and * jump to the reset vector. */ - - __asm__ __volatile__("movi a2, 15\n\t" - "wsr a2, icountlevel\n\t" - "movi a2, 0\n\t" - "wsr a2, icount\n\t" -#if XCHAL_NUM_IBREAK > 0 - "wsr a2, ibreakenable\n\t" -#endif -#if XCHAL_HAVE_LOOPS - "wsr a2, lcount\n\t" -#endif - "movi a2, 0x1f\n\t" - "wsr a2, ps\n\t" - "isync\n\t" - "jx %0\n\t" - : - : "a" (XCHAL_RESET_VECTOR_VADDR) - : "a2"); - + cpu_reset(); /* control never gets here */ } @@ -98,7 +82,7 @@ void platform_heartbeat(void) static int iss_panic_event(struct notifier_block *this, unsigned long event, void *ptr) { - __asm__ __volatile__("movi a2, -1; simcall\n"); + simc_exit(1); return NOTIFY_DONE; } diff --git a/arch/xtensa/platforms/iss/simdisk.c b/arch/xtensa/platforms/iss/simdisk.c index f58a4e6472cbc5fd9988d8bfb73d3a80e4806bfd..ede04cca30dde3000930831db1ce161e25447a28 100644 --- a/arch/xtensa/platforms/iss/simdisk.c +++ b/arch/xtensa/platforms/iss/simdisk.c @@ -86,6 +86,7 @@ static void simdisk_transfer(struct simdisk *dev, unsigned long sector, unsigned long io; simc_lseek(dev->fd, offset, SEEK_SET); + READ_ONCE(*buffer); if (write) io = simc_write(dev->fd, buffer, nbytes); else diff --git a/arch/xtensa/platforms/xt2000/setup.c b/arch/xtensa/platforms/xt2000/setup.c index 4904c5c16918c146413d4c00af0febf37b25a0dc..9c2f1fb960d014308bde3c0bb889ca05e0953324 100644 --- a/arch/xtensa/platforms/xt2000/setup.c +++ b/arch/xtensa/platforms/xt2000/setup.c @@ -64,26 +64,7 @@ void platform_restart(void) { /* Flush and reset the mmu, simulate a processor reset, and * jump to the reset vector. */ - - __asm__ __volatile__ ("movi a2, 15\n\t" - "wsr a2, icountlevel\n\t" - "movi a2, 0\n\t" - "wsr a2, icount\n\t" -#if XCHAL_NUM_IBREAK > 0 - "wsr a2, ibreakenable\n\t" -#endif -#if XCHAL_HAVE_LOOPS - "wsr a2, lcount\n\t" -#endif - "movi a2, 0x1f\n\t" - "wsr a2, ps\n\t" - "isync\n\t" - "jx %0\n\t" - : - : "a" (XCHAL_RESET_VECTOR_VADDR) - : "a2" - ); - + cpu_reset(); /* control never gets here */ } diff --git a/arch/xtensa/platforms/xtfpga/setup.c b/arch/xtensa/platforms/xtfpga/setup.c index b509d1f55ed5c2445f1bb4930b48a84c9d34edce..779be723eb2bdd4fa03c6b30abd553e948df9991 100644 --- a/arch/xtensa/platforms/xtfpga/setup.c +++ b/arch/xtensa/platforms/xtfpga/setup.c @@ -26,6 +26,8 @@ #include #include #include +#include +#include #include #include @@ -54,58 +56,63 @@ void platform_restart(void) { /* Flush and reset the mmu, simulate a processor reset, and * jump to the reset vector. */ + cpu_reset(); + /* control never gets here */ +} +void __init platform_setup(char **cmdline) +{ +} - __asm__ __volatile__ ("movi a2, 15\n\t" - "wsr a2, icountlevel\n\t" - "movi a2, 0\n\t" - "wsr a2, icount\n\t" -#if XCHAL_NUM_IBREAK > 0 - "wsr a2, ibreakenable\n\t" -#endif -#if XCHAL_HAVE_LOOPS - "wsr a2, lcount\n\t" -#endif - "movi a2, 0x1f\n\t" - "wsr a2, ps\n\t" - "isync\n\t" - "jx %0\n\t" - : - : "a" (XCHAL_RESET_VECTOR_VADDR) - : "a2" - ); +/* early initialization */ - /* control never gets here */ +void __init platform_init(bp_tag_t *first) +{ } -void __init platform_setup(char **cmdline) +/* Heartbeat. */ + +void platform_heartbeat(void) +{ +} + +#ifdef CONFIG_XTENSA_CALIBRATE_CCOUNT + +void __init platform_calibrate_ccount(void) { + ccount_freq = *(long *)XTFPGA_CLKFRQ_VADDR; } +#endif + #ifdef CONFIG_OF -static void __init update_clock_frequency(struct device_node *node) +static void __init xtfpga_clk_setup(struct device_node *np) { - struct property *newfreq; + void __iomem *base = of_iomap(np, 0); + struct clk *clk; u32 freq; - if (!of_property_read_u32(node, "clock-frequency", &freq) && freq != 0) + if (!base) { + pr_err("%s: invalid address\n", np->name); return; + } - newfreq = kzalloc(sizeof(*newfreq) + sizeof(u32), GFP_KERNEL); - if (!newfreq) - return; - newfreq->value = newfreq + 1; - newfreq->length = sizeof(freq); - newfreq->name = kstrdup("clock-frequency", GFP_KERNEL); - if (!newfreq->name) { - kfree(newfreq); + freq = __raw_readl(base); + iounmap(base); + clk = clk_register_fixed_rate(NULL, np->name, NULL, 0, freq); + + if (IS_ERR(clk)) { + pr_err("%s: clk registration failed\n", np->name); return; } - *(u32 *)newfreq->value = cpu_to_be32(*(u32 *)XTFPGA_CLKFRQ_VADDR); - of_update_property(node, newfreq); + if (of_clk_add_provider(np, of_clk_src_simple_get, clk)) { + pr_err("%s: clk provider registration failed\n", np->name); + return; + } } +CLK_OF_DECLARE(xtfpga_clk, "cdns,xtfpga-clock", xtfpga_clk_setup); #define MAC_LEN 6 static void __init update_local_mac(struct device_node *node) @@ -137,56 +144,15 @@ static void __init update_local_mac(struct device_node *node) static int __init machine_setup(void) { - struct device_node *clock; struct device_node *eth = NULL; - for_each_node_by_name(clock, "main-oscillator") - update_clock_frequency(clock); - if ((eth = of_find_compatible_node(eth, NULL, "opencores,ethoc"))) update_local_mac(eth); return 0; } arch_initcall(machine_setup); -#endif - -/* early initialization */ - -void __init platform_init(bp_tag_t *first) -{ -} - -/* Heartbeat. */ - -void platform_heartbeat(void) -{ -} - -#ifdef CONFIG_XTENSA_CALIBRATE_CCOUNT - -void __init platform_calibrate_ccount(void) -{ - long clk_freq = 0; -#ifdef CONFIG_OF - struct device_node *cpu = - of_find_compatible_node(NULL, NULL, "cdns,xtensa-cpu"); - if (cpu) { - u32 freq; - update_clock_frequency(cpu); - if (!of_property_read_u32(cpu, "clock-frequency", &freq)) - clk_freq = freq; - } -#endif - if (!clk_freq) - clk_freq = *(long *)XTFPGA_CLKFRQ_VADDR; - - ccount_freq = clk_freq; -} - -#endif - -#ifndef CONFIG_OF +#else #include #include diff --git a/arch/xtensa/variants/csp/include/variant/core.h b/arch/xtensa/variants/csp/include/variant/core.h new file mode 100644 index 0000000000000000000000000000000000000000..ccd81f07eaf3635e340a9c517484afbf40e49332 --- /dev/null +++ b/arch/xtensa/variants/csp/include/variant/core.h @@ -0,0 +1,575 @@ +/* + * xtensa/config/core-isa.h -- HAL definitions that are dependent on Xtensa + * processor CORE configuration + * + * See , which includes this file, for more details. + */ + +/* Xtensa processor core configuration information. + + Copyright (c) 1999-2015 Tensilica Inc. + + Permission is hereby granted, free of charge, to any person obtaining + a copy of this software and associated documentation files (the + "Software"), to deal in the Software without restriction, including + without limitation the rights to use, copy, modify, merge, publish, + distribute, sublicense, and/or sell copies of the Software, and to + permit persons to whom the Software is furnished to do so, subject to + the following conditions: + + The above copyright notice and this permission notice shall be included + in all copies or substantial portions of the Software. + + THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF + MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. + IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY + CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, + TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE + SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. */ + +#ifndef _XTENSA_CORE_CONFIGURATION_H +#define _XTENSA_CORE_CONFIGURATION_H + + +/**************************************************************************** + Parameters Useful for Any Code, USER or PRIVILEGED + ****************************************************************************/ + +/* + * Note: Macros of the form XCHAL_HAVE_*** have a value of 1 if the option is + * configured, and a value of 0 otherwise. These macros are always defined. + */ + + +/*---------------------------------------------------------------------- + ISA + ----------------------------------------------------------------------*/ + +#define XCHAL_HAVE_BE 0 /* big-endian byte ordering */ +#define XCHAL_HAVE_WINDOWED 1 /* windowed registers option */ +#define XCHAL_NUM_AREGS 32 /* num of physical addr regs */ +#define XCHAL_NUM_AREGS_LOG2 5 /* log2(XCHAL_NUM_AREGS) */ +#define XCHAL_MAX_INSTRUCTION_SIZE 8 /* max instr bytes (3..8) */ +#define XCHAL_HAVE_DEBUG 1 /* debug option */ +#define XCHAL_HAVE_DENSITY 1 /* 16-bit instructions */ +#define XCHAL_HAVE_LOOPS 1 /* zero-overhead loops */ +#define XCHAL_LOOP_BUFFER_SIZE 0 /* zero-ov. loop instr buffer size */ +#define XCHAL_HAVE_NSA 1 /* NSA/NSAU instructions */ +#define XCHAL_HAVE_MINMAX 1 /* MIN/MAX instructions */ +#define XCHAL_HAVE_SEXT 1 /* SEXT instruction */ +#define XCHAL_HAVE_DEPBITS 0 /* DEPBITS instruction */ +#define XCHAL_HAVE_CLAMPS 1 /* CLAMPS instruction */ +#define XCHAL_HAVE_MUL16 1 /* MUL16S/MUL16U instructions */ +#define XCHAL_HAVE_MUL32 1 /* MULL instruction */ +#define XCHAL_HAVE_MUL32_HIGH 1 /* MULUH/MULSH instructions */ +#define XCHAL_HAVE_DIV32 1 /* QUOS/QUOU/REMS/REMU instructions */ +#define XCHAL_HAVE_L32R 1 /* L32R instruction */ +#define XCHAL_HAVE_ABSOLUTE_LITERALS 0 /* non-PC-rel (extended) L32R */ +#define XCHAL_HAVE_CONST16 0 /* CONST16 instruction */ +#define XCHAL_HAVE_ADDX 1 /* ADDX#/SUBX# instructions */ +#define XCHAL_HAVE_WIDE_BRANCHES 0 /* B*.W18 or B*.W15 instr's */ +#define XCHAL_HAVE_PREDICTED_BRANCHES 0 /* B[EQ/EQZ/NE/NEZ]T instr's */ +#define XCHAL_HAVE_CALL4AND12 1 /* (obsolete option) */ +#define XCHAL_HAVE_ABS 1 /* ABS instruction */ +/*#define XCHAL_HAVE_POPC 0*/ /* POPC instruction */ +/*#define XCHAL_HAVE_CRC 0*/ /* CRC instruction */ +#define XCHAL_HAVE_RELEASE_SYNC 1 /* L32AI/S32RI instructions */ +#define XCHAL_HAVE_S32C1I 1 /* S32C1I instruction */ +#define XCHAL_HAVE_SPECULATION 0 /* speculation */ +#define XCHAL_HAVE_FULL_RESET 1 /* all regs/state reset */ +#define XCHAL_NUM_CONTEXTS 1 /* */ +#define XCHAL_NUM_MISC_REGS 4 /* num of scratch regs (0..4) */ +#define XCHAL_HAVE_TAP_MASTER 0 /* JTAG TAP control instr's */ +#define XCHAL_HAVE_PRID 1 /* processor ID register */ +#define XCHAL_HAVE_EXTERN_REGS 1 /* WER/RER instructions */ +#define XCHAL_HAVE_MX 0 /* MX core (Tensilica internal) */ +#define XCHAL_HAVE_MP_INTERRUPTS 0 /* interrupt distributor port */ +#define XCHAL_HAVE_MP_RUNSTALL 0 /* core RunStall control port */ +#define XCHAL_HAVE_PSO 0 /* Power Shut-Off */ +#define XCHAL_HAVE_PSO_CDM 0 /* core/debug/mem pwr domains */ +#define XCHAL_HAVE_PSO_FULL_RETENTION 0 /* all regs preserved on PSO */ +#define XCHAL_HAVE_THREADPTR 1 /* THREADPTR register */ +#define XCHAL_HAVE_BOOLEANS 1 /* boolean registers */ +#define XCHAL_HAVE_CP 1 /* CPENABLE reg (coprocessor) */ +#define XCHAL_CP_MAXCFG 8 /* max allowed cp id plus one */ +#define XCHAL_HAVE_MAC16 1 /* MAC16 package */ + +#define XCHAL_HAVE_FUSION 0 /* Fusion*/ +#define XCHAL_HAVE_FUSION_FP 0 /* Fusion FP option */ +#define XCHAL_HAVE_FUSION_LOW_POWER 0 /* Fusion Low Power option */ +#define XCHAL_HAVE_FUSION_AES 0 /* Fusion BLE/Wifi AES-128 CCM option */ +#define XCHAL_HAVE_FUSION_CONVENC 0 /* Fusion Conv Encode option */ +#define XCHAL_HAVE_FUSION_LFSR_CRC 0 /* Fusion LFSR-CRC option */ +#define XCHAL_HAVE_FUSION_BITOPS 0 /* Fusion Bit Operations Support option */ +#define XCHAL_HAVE_FUSION_AVS 0 /* Fusion AVS option */ +#define XCHAL_HAVE_FUSION_16BIT_BASEBAND 0 /* Fusion 16-bit Baseband option */ +#define XCHAL_HAVE_HIFIPRO 0 /* HiFiPro Audio Engine pkg */ +#define XCHAL_HAVE_HIFI4 0 /* HiFi4 Audio Engine pkg */ +#define XCHAL_HAVE_HIFI4_VFPU 0 /* HiFi4 Audio Engine VFPU option */ +#define XCHAL_HAVE_HIFI3 0 /* HiFi3 Audio Engine pkg */ +#define XCHAL_HAVE_HIFI3_VFPU 0 /* HiFi3 Audio Engine VFPU option */ +#define XCHAL_HAVE_HIFI2 0 /* HiFi2 Audio Engine pkg */ +#define XCHAL_HAVE_HIFI2EP 0 /* HiFi2EP */ +#define XCHAL_HAVE_HIFI_MINI 0 + + +#define XCHAL_HAVE_VECTORFPU2005 0 /* vector or user floating-point pkg */ +#define XCHAL_HAVE_USER_DPFPU 0 /* user DP floating-point pkg */ +#define XCHAL_HAVE_USER_SPFPU 0 /* user DP floating-point pkg */ +#define XCHAL_HAVE_FP 0 /* single prec floating point */ +#define XCHAL_HAVE_FP_DIV 0 /* FP with DIV instructions */ +#define XCHAL_HAVE_FP_RECIP 0 /* FP with RECIP instructions */ +#define XCHAL_HAVE_FP_SQRT 0 /* FP with SQRT instructions */ +#define XCHAL_HAVE_FP_RSQRT 0 /* FP with RSQRT instructions */ +#define XCHAL_HAVE_DFP 0 /* double precision FP pkg */ +#define XCHAL_HAVE_DFP_DIV 0 /* DFP with DIV instructions */ +#define XCHAL_HAVE_DFP_RECIP 0 /* DFP with RECIP instructions*/ +#define XCHAL_HAVE_DFP_SQRT 0 /* DFP with SQRT instructions */ +#define XCHAL_HAVE_DFP_RSQRT 0 /* DFP with RSQRT instructions*/ +#define XCHAL_HAVE_DFP_ACCEL 0 /* double precision FP acceleration pkg */ +#define XCHAL_HAVE_DFP_accel XCHAL_HAVE_DFP_ACCEL /* for backward compatibility */ + +#define XCHAL_HAVE_DFPU_SINGLE_ONLY 0 /* DFPU Coprocessor, single precision only */ +#define XCHAL_HAVE_DFPU_SINGLE_DOUBLE 0 /* DFPU Coprocessor, single and double precision */ +#define XCHAL_HAVE_VECTRA1 0 /* Vectra I pkg */ +#define XCHAL_HAVE_VECTRALX 0 /* Vectra LX pkg */ +#define XCHAL_HAVE_PDX4 0 /* PDX4 */ +#define XCHAL_HAVE_CONNXD2 0 /* ConnX D2 pkg */ +#define XCHAL_HAVE_CONNXD2_DUALLSFLIX 0 /* ConnX D2 & Dual LoadStore Flix */ +#define XCHAL_HAVE_BBE16 0 /* ConnX BBE16 pkg */ +#define XCHAL_HAVE_BBE16_RSQRT 0 /* BBE16 & vector recip sqrt */ +#define XCHAL_HAVE_BBE16_VECDIV 0 /* BBE16 & vector divide */ +#define XCHAL_HAVE_BBE16_DESPREAD 0 /* BBE16 & despread */ +#define XCHAL_HAVE_BBENEP 0 /* ConnX BBENEP pkgs */ +#define XCHAL_HAVE_BSP3 0 /* ConnX BSP3 pkg */ +#define XCHAL_HAVE_BSP3_TRANSPOSE 0 /* BSP3 & transpose32x32 */ +#define XCHAL_HAVE_SSP16 0 /* ConnX SSP16 pkg */ +#define XCHAL_HAVE_SSP16_VITERBI 0 /* SSP16 & viterbi */ +#define XCHAL_HAVE_TURBO16 0 /* ConnX Turbo16 pkg */ +#define XCHAL_HAVE_BBP16 0 /* ConnX BBP16 pkg */ +#define XCHAL_HAVE_FLIX3 0 /* basic 3-way FLIX option */ +#define XCHAL_HAVE_GRIVPEP 0 /* GRIVPEP is General Release of IVPEP */ +#define XCHAL_HAVE_GRIVPEP_HISTOGRAM 0 /* Histogram option on GRIVPEP */ + + +/*---------------------------------------------------------------------- + MISC + ----------------------------------------------------------------------*/ + +#define XCHAL_NUM_LOADSTORE_UNITS 1 /* load/store units */ +#define XCHAL_NUM_WRITEBUFFER_ENTRIES 8 /* size of write buffer */ +#define XCHAL_INST_FETCH_WIDTH 8 /* instr-fetch width in bytes */ +#define XCHAL_DATA_WIDTH 16 /* data width in bytes */ +#define XCHAL_DATA_PIPE_DELAY 1 /* d-side pipeline delay + (1 = 5-stage, 2 = 7-stage) */ +#define XCHAL_CLOCK_GATING_GLOBAL 0 /* global clock gating */ +#define XCHAL_CLOCK_GATING_FUNCUNIT 0 /* funct. unit clock gating */ +/* In T1050, applies to selected core load and store instructions (see ISA): */ +#define XCHAL_UNALIGNED_LOAD_EXCEPTION 1 /* unaligned loads cause exc. */ +#define XCHAL_UNALIGNED_STORE_EXCEPTION 1 /* unaligned stores cause exc.*/ +#define XCHAL_UNALIGNED_LOAD_HW 0 /* unaligned loads work in hw */ +#define XCHAL_UNALIGNED_STORE_HW 0 /* unaligned stores work in hw*/ + +#define XCHAL_SW_VERSION 1100002 /* sw version of this header */ + +#define XCHAL_CORE_ID "xt_lnx" /* alphanum core name + (CoreID) set in the Xtensa + Processor Generator */ + +#define XCHAL_BUILD_UNIQUE_ID 0x00057D54 /* 22-bit sw build ID */ + +/* + * These definitions describe the hardware targeted by this software. + */ +#define XCHAL_HW_CONFIGID0 0xC1B3FFFE /* ConfigID hi 32 bits*/ +#define XCHAL_HW_CONFIGID1 0x1C857D54 /* ConfigID lo 32 bits*/ +#define XCHAL_HW_VERSION_NAME "LX6.0.2" /* full version name */ +#define XCHAL_HW_VERSION_MAJOR 2600 /* major ver# of targeted hw */ +#define XCHAL_HW_VERSION_MINOR 2 /* minor ver# of targeted hw */ +#define XCHAL_HW_VERSION 260002 /* major*100+minor */ +#define XCHAL_HW_REL_LX6 1 +#define XCHAL_HW_REL_LX6_0 1 +#define XCHAL_HW_REL_LX6_0_2 1 +#define XCHAL_HW_CONFIGID_RELIABLE 1 +/* If software targets a *range* of hardware versions, these are the bounds: */ +#define XCHAL_HW_MIN_VERSION_MAJOR 2600 /* major v of earliest tgt hw */ +#define XCHAL_HW_MIN_VERSION_MINOR 2 /* minor v of earliest tgt hw */ +#define XCHAL_HW_MIN_VERSION 260002 /* earliest targeted hw */ +#define XCHAL_HW_MAX_VERSION_MAJOR 2600 /* major v of latest tgt hw */ +#define XCHAL_HW_MAX_VERSION_MINOR 2 /* minor v of latest tgt hw */ +#define XCHAL_HW_MAX_VERSION 260002 /* latest targeted hw */ + + +/*---------------------------------------------------------------------- + CACHE + ----------------------------------------------------------------------*/ + +#define XCHAL_ICACHE_LINESIZE 64 /* I-cache line size in bytes */ +#define XCHAL_DCACHE_LINESIZE 64 /* D-cache line size in bytes */ +#define XCHAL_ICACHE_LINEWIDTH 6 /* log2(I line size in bytes) */ +#define XCHAL_DCACHE_LINEWIDTH 6 /* log2(D line size in bytes) */ + +#define XCHAL_ICACHE_SIZE 65536 /* I-cache size in bytes or 0 */ +#define XCHAL_DCACHE_SIZE 16384 /* D-cache size in bytes or 0 */ + +#define XCHAL_DCACHE_IS_WRITEBACK 1 /* writeback feature */ +#define XCHAL_DCACHE_IS_COHERENT 0 /* MP coherence feature */ + +#define XCHAL_HAVE_PREFETCH 0 /* PREFCTL register */ +#define XCHAL_HAVE_PREFETCH_L1 0 /* prefetch to L1 dcache */ +#define XCHAL_PREFETCH_CASTOUT_LINES 0 /* dcache pref. castout bufsz */ +#define XCHAL_PREFETCH_ENTRIES 0 /* cache prefetch entries */ +#define XCHAL_PREFETCH_BLOCK_ENTRIES 0 /* prefetch block streams */ +#define XCHAL_HAVE_CACHE_BLOCKOPS 0 /* block prefetch for caches */ +#define XCHAL_HAVE_ICACHE_TEST 1 /* Icache test instructions */ +#define XCHAL_HAVE_DCACHE_TEST 1 /* Dcache test instructions */ +#define XCHAL_HAVE_ICACHE_DYN_WAYS 0 /* Icache dynamic way support */ +#define XCHAL_HAVE_DCACHE_DYN_WAYS 0 /* Dcache dynamic way support */ + + + + +/**************************************************************************** + Parameters Useful for PRIVILEGED (Supervisory or Non-Virtualized) Code + ****************************************************************************/ + + +#ifndef XTENSA_HAL_NON_PRIVILEGED_ONLY + +/*---------------------------------------------------------------------- + CACHE + ----------------------------------------------------------------------*/ + +#define XCHAL_HAVE_PIF 1 /* any outbound PIF present */ + +/* If present, cache size in bytes == (ways * 2^(linewidth + setwidth)). */ + +/* Number of cache sets in log2(lines per way): */ +#define XCHAL_ICACHE_SETWIDTH 8 +#define XCHAL_DCACHE_SETWIDTH 6 + +/* Cache set associativity (number of ways): */ +#define XCHAL_ICACHE_WAYS 4 +#define XCHAL_DCACHE_WAYS 4 + +/* Cache features: */ +#define XCHAL_ICACHE_LINE_LOCKABLE 1 +#define XCHAL_DCACHE_LINE_LOCKABLE 1 +#define XCHAL_ICACHE_ECC_PARITY 0 +#define XCHAL_DCACHE_ECC_PARITY 0 + +/* Cache access size in bytes (affects operation of SICW instruction): */ +#define XCHAL_ICACHE_ACCESS_SIZE 16 +#define XCHAL_DCACHE_ACCESS_SIZE 16 + +#define XCHAL_DCACHE_BANKS 1 /* number of banks */ + +/* Number of encoded cache attr bits (see for decoded bits): */ +#define XCHAL_CA_BITS 4 + +/* Whether MEMCTL register has anything useful */ +#define XCHAL_USE_MEMCTL (((XCHAL_LOOP_BUFFER_SIZE > 0) || \ + XCHAL_DCACHE_IS_COHERENT || \ + XCHAL_HAVE_ICACHE_DYN_WAYS || \ + XCHAL_HAVE_DCACHE_DYN_WAYS) && \ + (XCHAL_HW_MIN_VERSION >= XTENSA_HWVERSION_RE_2012_0)) + + +/*---------------------------------------------------------------------- + INTERNAL I/D RAM/ROMs and XLMI + ----------------------------------------------------------------------*/ + +#define XCHAL_NUM_INSTROM 0 /* number of core instr. ROMs */ +#define XCHAL_NUM_INSTRAM 0 /* number of core instr. RAMs */ +#define XCHAL_NUM_DATAROM 0 /* number of core data ROMs */ +#define XCHAL_NUM_DATARAM 0 /* number of core data RAMs */ +#define XCHAL_NUM_URAM 0 /* number of core unified RAMs*/ +#define XCHAL_NUM_XLMI 0 /* number of core XLMI ports */ + +#define XCHAL_HAVE_IMEM_LOADSTORE 1 /* can load/store to IROM/IRAM*/ + + +/*---------------------------------------------------------------------- + INTERRUPTS and TIMERS + ----------------------------------------------------------------------*/ + +#define XCHAL_HAVE_INTERRUPTS 1 /* interrupt option */ +#define XCHAL_HAVE_HIGHPRI_INTERRUPTS 1 /* med/high-pri. interrupts */ +#define XCHAL_HAVE_NMI 1 /* non-maskable interrupt */ +#define XCHAL_HAVE_CCOUNT 1 /* CCOUNT reg. (timer option) */ +#define XCHAL_NUM_TIMERS 3 /* number of CCOMPAREn regs */ +#define XCHAL_NUM_INTERRUPTS 22 /* number of interrupts */ +#define XCHAL_NUM_INTERRUPTS_LOG2 5 /* ceil(log2(NUM_INTERRUPTS)) */ +#define XCHAL_NUM_EXTINTERRUPTS 16 /* num of external interrupts */ +#define XCHAL_NUM_INTLEVELS 6 /* number of interrupt levels + (not including level zero) */ +#define XCHAL_EXCM_LEVEL 3 /* level masked by PS.EXCM */ + /* (always 1 in XEA1; levels 2 .. EXCM_LEVEL are "medium priority") */ + +/* Masks of interrupts at each interrupt level: */ +#define XCHAL_INTLEVEL1_MASK 0x001F00BF +#define XCHAL_INTLEVEL2_MASK 0x00001140 +#define XCHAL_INTLEVEL3_MASK 0x00200E00 +#define XCHAL_INTLEVEL4_MASK 0x00008000 +#define XCHAL_INTLEVEL5_MASK 0x00002000 +#define XCHAL_INTLEVEL6_MASK 0x00000000 +#define XCHAL_INTLEVEL7_MASK 0x00004000 + +/* Masks of interrupts at each range 1..n of interrupt levels: */ +#define XCHAL_INTLEVEL1_ANDBELOW_MASK 0x001F00BF +#define XCHAL_INTLEVEL2_ANDBELOW_MASK 0x001F11FF +#define XCHAL_INTLEVEL3_ANDBELOW_MASK 0x003F1FFF +#define XCHAL_INTLEVEL4_ANDBELOW_MASK 0x003F9FFF +#define XCHAL_INTLEVEL5_ANDBELOW_MASK 0x003FBFFF +#define XCHAL_INTLEVEL6_ANDBELOW_MASK 0x003FBFFF +#define XCHAL_INTLEVEL7_ANDBELOW_MASK 0x003FFFFF + +/* Level of each interrupt: */ +#define XCHAL_INT0_LEVEL 1 +#define XCHAL_INT1_LEVEL 1 +#define XCHAL_INT2_LEVEL 1 +#define XCHAL_INT3_LEVEL 1 +#define XCHAL_INT4_LEVEL 1 +#define XCHAL_INT5_LEVEL 1 +#define XCHAL_INT6_LEVEL 2 +#define XCHAL_INT7_LEVEL 1 +#define XCHAL_INT8_LEVEL 2 +#define XCHAL_INT9_LEVEL 3 +#define XCHAL_INT10_LEVEL 3 +#define XCHAL_INT11_LEVEL 3 +#define XCHAL_INT12_LEVEL 2 +#define XCHAL_INT13_LEVEL 5 +#define XCHAL_INT14_LEVEL 7 +#define XCHAL_INT15_LEVEL 4 +#define XCHAL_INT16_LEVEL 1 +#define XCHAL_INT17_LEVEL 1 +#define XCHAL_INT18_LEVEL 1 +#define XCHAL_INT19_LEVEL 1 +#define XCHAL_INT20_LEVEL 1 +#define XCHAL_INT21_LEVEL 3 +#define XCHAL_DEBUGLEVEL 6 /* debug interrupt level */ +#define XCHAL_HAVE_DEBUG_EXTERN_INT 1 /* OCD external db interrupt */ +#define XCHAL_NMILEVEL 7 /* NMI "level" (for use with + EXCSAVE/EPS/EPC_n, RFI n) */ + +/* Type of each interrupt: */ +#define XCHAL_INT0_TYPE XTHAL_INTTYPE_EXTERN_LEVEL +#define XCHAL_INT1_TYPE XTHAL_INTTYPE_EXTERN_LEVEL +#define XCHAL_INT2_TYPE XTHAL_INTTYPE_EXTERN_LEVEL +#define XCHAL_INT3_TYPE XTHAL_INTTYPE_EXTERN_LEVEL +#define XCHAL_INT4_TYPE XTHAL_INTTYPE_EXTERN_LEVEL +#define XCHAL_INT5_TYPE XTHAL_INTTYPE_EXTERN_LEVEL +#define XCHAL_INT6_TYPE XTHAL_INTTYPE_TIMER +#define XCHAL_INT7_TYPE XTHAL_INTTYPE_SOFTWARE +#define XCHAL_INT8_TYPE XTHAL_INTTYPE_EXTERN_LEVEL +#define XCHAL_INT9_TYPE XTHAL_INTTYPE_EXTERN_LEVEL +#define XCHAL_INT10_TYPE XTHAL_INTTYPE_TIMER +#define XCHAL_INT11_TYPE XTHAL_INTTYPE_SOFTWARE +#define XCHAL_INT12_TYPE XTHAL_INTTYPE_EXTERN_EDGE +#define XCHAL_INT13_TYPE XTHAL_INTTYPE_TIMER +#define XCHAL_INT14_TYPE XTHAL_INTTYPE_NMI +#define XCHAL_INT15_TYPE XTHAL_INTTYPE_PROFILING +#define XCHAL_INT16_TYPE XTHAL_INTTYPE_EXTERN_EDGE +#define XCHAL_INT17_TYPE XTHAL_INTTYPE_EXTERN_EDGE +#define XCHAL_INT18_TYPE XTHAL_INTTYPE_EXTERN_EDGE +#define XCHAL_INT19_TYPE XTHAL_INTTYPE_EXTERN_EDGE +#define XCHAL_INT20_TYPE XTHAL_INTTYPE_EXTERN_EDGE +#define XCHAL_INT21_TYPE XTHAL_INTTYPE_EXTERN_EDGE + +/* Masks of interrupts for each type of interrupt: */ +#define XCHAL_INTTYPE_MASK_UNCONFIGURED 0xFFC00000 +#define XCHAL_INTTYPE_MASK_SOFTWARE 0x00000880 +#define XCHAL_INTTYPE_MASK_EXTERN_EDGE 0x003F1000 +#define XCHAL_INTTYPE_MASK_EXTERN_LEVEL 0x0000033F +#define XCHAL_INTTYPE_MASK_TIMER 0x00002440 +#define XCHAL_INTTYPE_MASK_NMI 0x00004000 +#define XCHAL_INTTYPE_MASK_WRITE_ERROR 0x00000000 +#define XCHAL_INTTYPE_MASK_PROFILING 0x00008000 + +/* Interrupt numbers assigned to specific interrupt sources: */ +#define XCHAL_TIMER0_INTERRUPT 6 /* CCOMPARE0 */ +#define XCHAL_TIMER1_INTERRUPT 10 /* CCOMPARE1 */ +#define XCHAL_TIMER2_INTERRUPT 13 /* CCOMPARE2 */ +#define XCHAL_TIMER3_INTERRUPT XTHAL_TIMER_UNCONFIGURED +#define XCHAL_NMI_INTERRUPT 14 /* non-maskable interrupt */ +#define XCHAL_PROFILING_INTERRUPT 15 /* profiling interrupt */ + +/* Interrupt numbers for levels at which only one interrupt is configured: */ +#define XCHAL_INTLEVEL4_NUM 15 +#define XCHAL_INTLEVEL5_NUM 13 +#define XCHAL_INTLEVEL7_NUM 14 +/* (There are many interrupts each at level(s) 1, 2, 3.) */ + + +/* + * External interrupt mapping. + * These macros describe how Xtensa processor interrupt numbers + * (as numbered internally, eg. in INTERRUPT and INTENABLE registers) + * map to external BInterrupt pins, for those interrupts + * configured as external (level-triggered, edge-triggered, or NMI). + * See the Xtensa processor databook for more details. + */ + +/* Core interrupt numbers mapped to each EXTERNAL BInterrupt pin number: */ +#define XCHAL_EXTINT0_NUM 0 /* (intlevel 1) */ +#define XCHAL_EXTINT1_NUM 1 /* (intlevel 1) */ +#define XCHAL_EXTINT2_NUM 2 /* (intlevel 1) */ +#define XCHAL_EXTINT3_NUM 3 /* (intlevel 1) */ +#define XCHAL_EXTINT4_NUM 4 /* (intlevel 1) */ +#define XCHAL_EXTINT5_NUM 5 /* (intlevel 1) */ +#define XCHAL_EXTINT6_NUM 8 /* (intlevel 2) */ +#define XCHAL_EXTINT7_NUM 9 /* (intlevel 3) */ +#define XCHAL_EXTINT8_NUM 12 /* (intlevel 2) */ +#define XCHAL_EXTINT9_NUM 14 /* (intlevel 7) */ +#define XCHAL_EXTINT10_NUM 16 /* (intlevel 1) */ +#define XCHAL_EXTINT11_NUM 17 /* (intlevel 1) */ +#define XCHAL_EXTINT12_NUM 18 /* (intlevel 1) */ +#define XCHAL_EXTINT13_NUM 19 /* (intlevel 1) */ +#define XCHAL_EXTINT14_NUM 20 /* (intlevel 1) */ +#define XCHAL_EXTINT15_NUM 21 /* (intlevel 3) */ +/* EXTERNAL BInterrupt pin numbers mapped to each core interrupt number: */ +#define XCHAL_INT0_EXTNUM 0 /* (intlevel 1) */ +#define XCHAL_INT1_EXTNUM 1 /* (intlevel 1) */ +#define XCHAL_INT2_EXTNUM 2 /* (intlevel 1) */ +#define XCHAL_INT3_EXTNUM 3 /* (intlevel 1) */ +#define XCHAL_INT4_EXTNUM 4 /* (intlevel 1) */ +#define XCHAL_INT5_EXTNUM 5 /* (intlevel 1) */ +#define XCHAL_INT8_EXTNUM 6 /* (intlevel 2) */ +#define XCHAL_INT9_EXTNUM 7 /* (intlevel 3) */ +#define XCHAL_INT12_EXTNUM 8 /* (intlevel 2) */ +#define XCHAL_INT14_EXTNUM 9 /* (intlevel 7) */ +#define XCHAL_INT16_EXTNUM 10 /* (intlevel 1) */ +#define XCHAL_INT17_EXTNUM 11 /* (intlevel 1) */ +#define XCHAL_INT18_EXTNUM 12 /* (intlevel 1) */ +#define XCHAL_INT19_EXTNUM 13 /* (intlevel 1) */ +#define XCHAL_INT20_EXTNUM 14 /* (intlevel 1) */ +#define XCHAL_INT21_EXTNUM 15 /* (intlevel 3) */ + + +/*---------------------------------------------------------------------- + EXCEPTIONS and VECTORS + ----------------------------------------------------------------------*/ + +#define XCHAL_XEA_VERSION 2 /* Xtensa Exception Architecture + number: 1 == XEA1 (old) + 2 == XEA2 (new) + 0 == XEAX (extern) or TX */ +#define XCHAL_HAVE_XEA1 0 /* Exception Architecture 1 */ +#define XCHAL_HAVE_XEA2 1 /* Exception Architecture 2 */ +#define XCHAL_HAVE_XEAX 0 /* External Exception Arch. */ +#define XCHAL_HAVE_EXCEPTIONS 1 /* exception option */ +#define XCHAL_HAVE_HALT 0 /* halt architecture option */ +#define XCHAL_HAVE_BOOTLOADER 0 /* boot loader (for TX) */ +#define XCHAL_HAVE_MEM_ECC_PARITY 0 /* local memory ECC/parity */ +#define XCHAL_HAVE_VECTOR_SELECT 1 /* relocatable vectors */ +#define XCHAL_HAVE_VECBASE 1 /* relocatable vectors */ +#define XCHAL_VECBASE_RESET_VADDR 0x00002000 /* VECBASE reset value */ +#define XCHAL_VECBASE_RESET_PADDR 0x00002000 +#define XCHAL_RESET_VECBASE_OVERLAP 0 + +#define XCHAL_RESET_VECTOR0_VADDR 0xFE000000 +#define XCHAL_RESET_VECTOR0_PADDR 0xFE000000 +#define XCHAL_RESET_VECTOR1_VADDR 0x00001000 +#define XCHAL_RESET_VECTOR1_PADDR 0x00001000 +#define XCHAL_RESET_VECTOR_VADDR 0xFE000000 +#define XCHAL_RESET_VECTOR_PADDR 0xFE000000 +#define XCHAL_USER_VECOFS 0x00000340 +#define XCHAL_USER_VECTOR_VADDR 0x00002340 +#define XCHAL_USER_VECTOR_PADDR 0x00002340 +#define XCHAL_KERNEL_VECOFS 0x00000300 +#define XCHAL_KERNEL_VECTOR_VADDR 0x00002300 +#define XCHAL_KERNEL_VECTOR_PADDR 0x00002300 +#define XCHAL_DOUBLEEXC_VECOFS 0x000003C0 +#define XCHAL_DOUBLEEXC_VECTOR_VADDR 0x000023C0 +#define XCHAL_DOUBLEEXC_VECTOR_PADDR 0x000023C0 +#define XCHAL_WINDOW_OF4_VECOFS 0x00000000 +#define XCHAL_WINDOW_UF4_VECOFS 0x00000040 +#define XCHAL_WINDOW_OF8_VECOFS 0x00000080 +#define XCHAL_WINDOW_UF8_VECOFS 0x000000C0 +#define XCHAL_WINDOW_OF12_VECOFS 0x00000100 +#define XCHAL_WINDOW_UF12_VECOFS 0x00000140 +#define XCHAL_WINDOW_VECTORS_VADDR 0x00002000 +#define XCHAL_WINDOW_VECTORS_PADDR 0x00002000 +#define XCHAL_INTLEVEL2_VECOFS 0x00000180 +#define XCHAL_INTLEVEL2_VECTOR_VADDR 0x00002180 +#define XCHAL_INTLEVEL2_VECTOR_PADDR 0x00002180 +#define XCHAL_INTLEVEL3_VECOFS 0x000001C0 +#define XCHAL_INTLEVEL3_VECTOR_VADDR 0x000021C0 +#define XCHAL_INTLEVEL3_VECTOR_PADDR 0x000021C0 +#define XCHAL_INTLEVEL4_VECOFS 0x00000200 +#define XCHAL_INTLEVEL4_VECTOR_VADDR 0x00002200 +#define XCHAL_INTLEVEL4_VECTOR_PADDR 0x00002200 +#define XCHAL_INTLEVEL5_VECOFS 0x00000240 +#define XCHAL_INTLEVEL5_VECTOR_VADDR 0x00002240 +#define XCHAL_INTLEVEL5_VECTOR_PADDR 0x00002240 +#define XCHAL_INTLEVEL6_VECOFS 0x00000280 +#define XCHAL_INTLEVEL6_VECTOR_VADDR 0x00002280 +#define XCHAL_INTLEVEL6_VECTOR_PADDR 0x00002280 +#define XCHAL_DEBUG_VECOFS XCHAL_INTLEVEL6_VECOFS +#define XCHAL_DEBUG_VECTOR_VADDR XCHAL_INTLEVEL6_VECTOR_VADDR +#define XCHAL_DEBUG_VECTOR_PADDR XCHAL_INTLEVEL6_VECTOR_PADDR +#define XCHAL_NMI_VECOFS 0x000002C0 +#define XCHAL_NMI_VECTOR_VADDR 0x000022C0 +#define XCHAL_NMI_VECTOR_PADDR 0x000022C0 +#define XCHAL_INTLEVEL7_VECOFS XCHAL_NMI_VECOFS +#define XCHAL_INTLEVEL7_VECTOR_VADDR XCHAL_NMI_VECTOR_VADDR +#define XCHAL_INTLEVEL7_VECTOR_PADDR XCHAL_NMI_VECTOR_PADDR + + +/*---------------------------------------------------------------------- + DEBUG MODULE + ----------------------------------------------------------------------*/ + +/* Misc */ +#define XCHAL_HAVE_DEBUG_ERI 1 /* ERI to debug module */ +#define XCHAL_HAVE_DEBUG_APB 1 /* APB to debug module */ +#define XCHAL_HAVE_DEBUG_JTAG 1 /* JTAG to debug module */ + +/* On-Chip Debug (OCD) */ +#define XCHAL_HAVE_OCD 1 /* OnChipDebug option */ +#define XCHAL_NUM_IBREAK 2 /* number of IBREAKn regs */ +#define XCHAL_NUM_DBREAK 2 /* number of DBREAKn regs */ +#define XCHAL_HAVE_OCD_DIR_ARRAY 0 /* faster OCD option (to LX4) */ +#define XCHAL_HAVE_OCD_LS32DDR 1 /* L32DDR/S32DDR (faster OCD) */ + +/* TRAX (in core) */ +#define XCHAL_HAVE_TRAX 1 /* TRAX in debug module */ +#define XCHAL_TRAX_MEM_SIZE 262144 /* TRAX memory size in bytes */ +#define XCHAL_TRAX_MEM_SHAREABLE 1 /* start/end regs; ready sig. */ +#define XCHAL_TRAX_ATB_WIDTH 0 /* ATB width (bits), 0=no ATB */ +#define XCHAL_TRAX_TIME_WIDTH 0 /* timestamp bitwidth, 0=none */ + +/* Perf counters */ +#define XCHAL_NUM_PERF_COUNTERS 8 /* performance counters */ + + +/*---------------------------------------------------------------------- + MMU + ----------------------------------------------------------------------*/ + +/* See core-matmap.h header file for more details. */ + +#define XCHAL_HAVE_TLBS 1 /* inverse of HAVE_CACHEATTR */ +#define XCHAL_HAVE_SPANNING_WAY 1 /* one way maps I+D 4GB vaddr */ +#define XCHAL_SPANNING_WAY 6 /* TLB spanning way number */ +#define XCHAL_HAVE_IDENTITY_MAP 0 /* vaddr == paddr always */ +#define XCHAL_HAVE_CACHEATTR 0 /* CACHEATTR register present */ +#define XCHAL_HAVE_MIMIC_CACHEATTR 0 /* region protection */ +#define XCHAL_HAVE_XLT_CACHEATTR 0 /* region prot. w/translation */ +#define XCHAL_HAVE_PTP_MMU 1 /* full MMU (with page table + [autorefill] and protection) + usable for an MMU-based OS */ +/* If none of the above last 4 are set, it's a custom TLB configuration. */ +#define XCHAL_ITLB_ARF_ENTRIES_LOG2 2 /* log2(autorefill way size) */ +#define XCHAL_DTLB_ARF_ENTRIES_LOG2 2 /* log2(autorefill way size) */ + +#define XCHAL_MMU_ASID_BITS 8 /* number of bits in ASIDs */ +#define XCHAL_MMU_RINGS 4 /* number of rings (1..4) */ +#define XCHAL_MMU_RING_BITS 2 /* num of bits in RING field */ + +#endif /* !XTENSA_HAL_NON_PRIVILEGED_ONLY */ + + +#endif /* _XTENSA_CORE_CONFIGURATION_H */ + diff --git a/arch/xtensa/variants/csp/include/variant/tie-asm.h b/arch/xtensa/variants/csp/include/variant/tie-asm.h new file mode 100644 index 0000000000000000000000000000000000000000..ba773c4a26a233e91eb25cd09903f69476dcc14e --- /dev/null +++ b/arch/xtensa/variants/csp/include/variant/tie-asm.h @@ -0,0 +1,194 @@ +/* + * tie-asm.h -- compile-time HAL assembler definitions dependent on CORE & TIE + * + * NOTE: This header file is not meant to be included directly. + */ + +/* This header file contains assembly-language definitions (assembly + macros, etc.) for this specific Xtensa processor's TIE extensions + and options. It is customized to this Xtensa processor configuration. + + Copyright (c) 1999-2015 Cadence Design Systems Inc. + + Permission is hereby granted, free of charge, to any person obtaining + a copy of this software and associated documentation files (the + "Software"), to deal in the Software without restriction, including + without limitation the rights to use, copy, modify, merge, publish, + distribute, sublicense, and/or sell copies of the Software, and to + permit persons to whom the Software is furnished to do so, subject to + the following conditions: + + The above copyright notice and this permission notice shall be included + in all copies or substantial portions of the Software. + + THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF + MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. + IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY + CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, + TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE + SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. */ + +#ifndef _XTENSA_CORE_TIE_ASM_H +#define _XTENSA_CORE_TIE_ASM_H + +/* Selection parameter values for save-area save/restore macros: */ +/* Option vs. TIE: */ +#define XTHAL_SAS_TIE 0x0001 /* custom extension or coprocessor */ +#define XTHAL_SAS_OPT 0x0002 /* optional (and not a coprocessor) */ +#define XTHAL_SAS_ANYOT 0x0003 /* both of the above */ +/* Whether used automatically by compiler: */ +#define XTHAL_SAS_NOCC 0x0004 /* not used by compiler w/o special opts/code */ +#define XTHAL_SAS_CC 0x0008 /* used by compiler without special opts/code */ +#define XTHAL_SAS_ANYCC 0x000C /* both of the above */ +/* ABI handling across function calls: */ +#define XTHAL_SAS_CALR 0x0010 /* caller-saved */ +#define XTHAL_SAS_CALE 0x0020 /* callee-saved */ +#define XTHAL_SAS_GLOB 0x0040 /* global across function calls (in thread) */ +#define XTHAL_SAS_ANYABI 0x0070 /* all of the above three */ +/* Misc */ +#define XTHAL_SAS_ALL 0xFFFF /* include all default NCP contents */ +#define XTHAL_SAS3(optie,ccuse,abi) ( ((optie) & XTHAL_SAS_ANYOT) \ + | ((ccuse) & XTHAL_SAS_ANYCC) \ + | ((abi) & XTHAL_SAS_ANYABI) ) + + + /* + * Macro to store all non-coprocessor (extra) custom TIE and optional state + * (not including zero-overhead loop registers). + * Required parameters: + * ptr Save area pointer address register (clobbered) + * (register must contain a 4 byte aligned address). + * at1..at4 Four temporary address registers (first XCHAL_NCP_NUM_ATMPS + * registers are clobbered, the remaining are unused). + * Optional parameters: + * continue If macro invoked as part of a larger store sequence, set to 1 + * if this is not the first in the sequence. Defaults to 0. + * ofs Offset from start of larger sequence (from value of first ptr + * in sequence) at which to store. Defaults to next available space + * (or 0 if is 0). + * select Select what category(ies) of registers to store, as a bitmask + * (see XTHAL_SAS_xxx constants). Defaults to all registers. + * alloc Select what category(ies) of registers to allocate; if any + * category is selected here that is not in , space for + * the corresponding registers is skipped without doing any load. + */ + .macro xchal_ncp_load ptr at1 at2 at3 at4 continue=0 ofs=-1 select=XTHAL_SAS_ALL alloc=0 + xchal_sa_start \continue, \ofs + // Optional global registers used by default by the compiler: + .ifeq (XTHAL_SAS_OPT | XTHAL_SAS_CC | XTHAL_SAS_GLOB) & ~(\select) + xchal_sa_align \ptr, 0, 1020, 4, 4 + l32i \at1, \ptr, .Lxchal_ofs_+0 + wur.THREADPTR \at1 // threadptr option + .set .Lxchal_ofs_, .Lxchal_ofs_ + 4 + .elseif ((XTHAL_SAS_OPT | XTHAL_SAS_CC | XTHAL_SAS_GLOB) & ~(\alloc)) == 0 + xchal_sa_align \ptr, 0, 1020, 4, 4 + .set .Lxchal_ofs_, .Lxchal_ofs_ + 4 + .endif + // Optional caller-saved registers used by default by the compiler: + .ifeq (XTHAL_SAS_OPT | XTHAL_SAS_CC | XTHAL_SAS_CALR) & ~(\select) + xchal_sa_align \ptr, 0, 1016, 4, 4 + l32i \at1, \ptr, .Lxchal_ofs_+0 + wsr.ACCLO \at1 // MAC16 option + l32i \at1, \ptr, .Lxchal_ofs_+4 + wsr.ACCHI \at1 // MAC16 option + .set .Lxchal_ofs_, .Lxchal_ofs_ + 8 + .elseif ((XTHAL_SAS_OPT | XTHAL_SAS_CC | XTHAL_SAS_CALR) & ~(\alloc)) == 0 + xchal_sa_align \ptr, 0, 1016, 4, 4 + .set .Lxchal_ofs_, .Lxchal_ofs_ + 8 + .endif + // Optional caller-saved registers not used by default by the compiler: + .ifeq (XTHAL_SAS_OPT | XTHAL_SAS_NOCC | XTHAL_SAS_CALR) & ~(\select) + xchal_sa_align \ptr, 0, 1000, 4, 4 + l32i \at1, \ptr, .Lxchal_ofs_+0 + wsr.BR \at1 // boolean option + l32i \at1, \ptr, .Lxchal_ofs_+4 + wsr.SCOMPARE1 \at1 // conditional store option + l32i \at1, \ptr, .Lxchal_ofs_+8 + wsr.M0 \at1 // MAC16 option + l32i \at1, \ptr, .Lxchal_ofs_+12 + wsr.M1 \at1 // MAC16 option + l32i \at1, \ptr, .Lxchal_ofs_+16 + wsr.M2 \at1 // MAC16 option + l32i \at1, \ptr, .Lxchal_ofs_+20 + wsr.M3 \at1 // MAC16 option + .set .Lxchal_ofs_, .Lxchal_ofs_ + 24 + .elseif ((XTHAL_SAS_OPT | XTHAL_SAS_NOCC | XTHAL_SAS_CALR) & ~(\alloc)) == 0 + xchal_sa_align \ptr, 0, 1000, 4, 4 + .set .Lxchal_ofs_, .Lxchal_ofs_ + 24 + .endif + .endm // xchal_ncp_load + + +#define XCHAL_NCP_NUM_ATMPS 1 + +#define XCHAL_SA_NUM_ATMPS 1 + +#endif /*_XTENSA_CORE_TIE_ASM_H*/ + diff --git a/arch/xtensa/variants/csp/include/variant/tie.h b/arch/xtensa/variants/csp/include/variant/tie.h new file mode 100644 index 0000000000000000000000000000000000000000..3ce391cfe449d21ff8bad950c353b7d2a62d65eb --- /dev/null +++ b/arch/xtensa/variants/csp/include/variant/tie.h @@ -0,0 +1,161 @@ +/* + * tie.h -- compile-time HAL definitions dependent on CORE & TIE configuration + * + * NOTE: This header file is not meant to be included directly. + */ + +/* This header file describes this specific Xtensa processor's TIE extensions + that extend basic Xtensa core functionality. It is customized to this + Xtensa processor configuration. + + Copyright (c) 1999-2015 Cadence Design Systems Inc. + + Permission is hereby granted, free of charge, to any person obtaining + a copy of this software and associated documentation files (the + "Software"), to deal in the Software without restriction, including + without limitation the rights to use, copy, modify, merge, publish, + distribute, sublicense, and/or sell copies of the Software, and to + permit persons to whom the Software is furnished to do so, subject to + the following conditions: + + The above copyright notice and this permission notice shall be included + in all copies or substantial portions of the Software. + + THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF + MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. + IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY + CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, + TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE + SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. */ + +#ifndef _XTENSA_CORE_TIE_H +#define _XTENSA_CORE_TIE_H + +#define XCHAL_CP_NUM 1 /* number of coprocessors */ +#define XCHAL_CP_MAX 8 /* max CP ID + 1 (0 if none) */ +#define XCHAL_CP_MASK 0x80 /* bitmask of all CPs by ID */ +#define XCHAL_CP_PORT_MASK 0x80 /* bitmask of only port CPs */ + +/* Basic parameters of each coprocessor: */ +#define XCHAL_CP7_NAME "XTIOP" +#define XCHAL_CP7_IDENT XTIOP +#define XCHAL_CP7_SA_SIZE 0 /* size of state save area */ +#define XCHAL_CP7_SA_ALIGN 1 /* min alignment of save area */ +#define XCHAL_CP_ID_XTIOP 7 /* coprocessor ID (0..7) */ + +/* Filler info for unassigned coprocessors, to simplify arrays etc: */ +#define XCHAL_CP0_SA_SIZE 0 +#define XCHAL_CP0_SA_ALIGN 1 +#define XCHAL_CP1_SA_SIZE 0 +#define XCHAL_CP1_SA_ALIGN 1 +#define XCHAL_CP2_SA_SIZE 0 +#define XCHAL_CP2_SA_ALIGN 1 +#define XCHAL_CP3_SA_SIZE 0 +#define XCHAL_CP3_SA_ALIGN 1 +#define XCHAL_CP4_SA_SIZE 0 +#define XCHAL_CP4_SA_ALIGN 1 +#define XCHAL_CP5_SA_SIZE 0 +#define XCHAL_CP5_SA_ALIGN 1 +#define XCHAL_CP6_SA_SIZE 0 +#define XCHAL_CP6_SA_ALIGN 1 + +/* Save area for non-coprocessor optional and custom (TIE) state: */ +#define XCHAL_NCP_SA_SIZE 36 +#define XCHAL_NCP_SA_ALIGN 4 + +/* Total save area for optional and custom state (NCP + CPn): */ +#define XCHAL_TOTAL_SA_SIZE 48 /* with 16-byte align padding */ +#define XCHAL_TOTAL_SA_ALIGN 4 /* actual minimum alignment */ + +/* + * Detailed contents of save areas. + * NOTE: caller must define the XCHAL_SA_REG macro (not defined here) + * before expanding the XCHAL_xxx_SA_LIST() macros. + * + * XCHAL_SA_REG(s,ccused,abikind,kind,opt,name,galign,align,asize, + * dbnum,base,regnum,bitsz,gapsz,reset,x...) + * + * s = passed from XCHAL_*_LIST(s), eg. to select how to expand + * ccused = set if used by compiler without special options or code + * abikind = 0 (caller-saved), 1 (callee-saved), or 2 (thread-global) + * kind = 0 (special reg), 1 (TIE user reg), or 2 (TIE regfile reg) + * opt = 0 (custom TIE extension or coprocessor), or 1 (optional reg) + * name = lowercase reg name (no quotes) + * galign = group byte alignment (power of 2) (galign >= align) + * align = register byte alignment (power of 2) + * asize = allocated size in bytes (asize*8 == bitsz + gapsz + padsz) + * (not including any pad bytes required to galign this or next reg) + * dbnum = unique target number f/debug (see ) + * base = reg shortname w/o index (or sr=special, ur=TIE user reg) + * regnum = reg index in regfile, or special/TIE-user reg number + * bitsz = number of significant bits (regfile width, or ur/sr mask bits) + * gapsz = intervening bits, if bitsz bits not stored contiguously + * (padsz = pad bits at end [TIE regfile] or at msbits [ur,sr] of asize) + * reset = register reset value (or 0 if undefined at reset) + * x = reserved for future use (0 until then) + * + * To filter out certain registers, e.g. to expand only the non-global + * registers used by the compiler, you can do something like this: + * + * #define XCHAL_SA_REG(s,ccused,p...) SELCC##ccused(p) + * #define SELCC0(p...) + * #define SELCC1(abikind,p...) SELAK##abikind(p) + * #define SELAK0(p...) REG(p) + * #define SELAK1(p...) REG(p) + * #define SELAK2(p...) + * #define REG(kind,tie,name,galn,aln,asz,csz,dbnum,base,rnum,bsz,rst,x...) \ + * ...what you want to expand... + */ + +#define XCHAL_NCP_SA_NUM 9 +#define XCHAL_NCP_SA_LIST(s) \ + XCHAL_SA_REG(s,1,2,1,1, threadptr, 4, 4, 4,0x03E7, ur,231, 32,0,0,0) \ + XCHAL_SA_REG(s,1,0,0,1, acclo, 4, 4, 4,0x0210, sr,16 , 32,0,0,0) \ + XCHAL_SA_REG(s,1,0,0,1, acchi, 4, 4, 4,0x0211, sr,17 , 8,0,0,0) \ + XCHAL_SA_REG(s,0,0,0,1, br, 4, 4, 4,0x0204, sr,4 , 16,0,0,0) \ + XCHAL_SA_REG(s,0,0,0,1, scompare1, 4, 4, 4,0x020C, sr,12 , 32,0,0,0) \ + XCHAL_SA_REG(s,0,0,0,1, m0, 4, 4, 4,0x0220, sr,32 , 32,0,0,0) \ + XCHAL_SA_REG(s,0,0,0,1, m1, 4, 4, 4,0x0221, sr,33 , 32,0,0,0) \ + XCHAL_SA_REG(s,0,0,0,1, m2, 4, 4, 4,0x0222, sr,34 , 32,0,0,0) \ + XCHAL_SA_REG(s,0,0,0,1, m3, 4, 4, 4,0x0223, sr,35 , 32,0,0,0) + +#define XCHAL_CP0_SA_NUM 0 +#define XCHAL_CP0_SA_LIST(s) /* empty */ + +#define XCHAL_CP1_SA_NUM 0 +#define XCHAL_CP1_SA_LIST(s) /* empty */ + +#define XCHAL_CP2_SA_NUM 0 +#define XCHAL_CP2_SA_LIST(s) /* empty */ + +#define XCHAL_CP3_SA_NUM 0 +#define XCHAL_CP3_SA_LIST(s) /* empty */ + +#define XCHAL_CP4_SA_NUM 0 +#define XCHAL_CP4_SA_LIST(s) /* empty */ + +#define XCHAL_CP5_SA_NUM 0 +#define XCHAL_CP5_SA_LIST(s) /* empty */ + +#define XCHAL_CP6_SA_NUM 0 +#define XCHAL_CP6_SA_LIST(s) /* empty */ + +#define XCHAL_CP7_SA_NUM 0 +#define XCHAL_CP7_SA_LIST(s) /* empty */ + +/* Byte length of instruction from its first nibble (op0 field), per FLIX. */ +#define XCHAL_OP0_FORMAT_LENGTHS 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3 +/* Byte length of instruction from its first byte, per FLIX. */ +#define XCHAL_BYTE0_FORMAT_LENGTHS \ + 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\ + 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\ + 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\ + 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\ + 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\ + 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\ + 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\ + 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3 + +#endif /*_XTENSA_CORE_TIE_H*/ +