Merge branch 'next' into resolution

Conflicts:
	drivers/extcon/extcon-adc-jack.c
	drivers/extcon/extcon-arizona.c
	drivers/extcon/extcon-gpio.c
	include/linux/extcon.h

Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.txt

+Driver for Broadcom Northstar USB 3.0 PHY
+
+Required properties:
+
+- compatible: one of: "brcm,ns-ax-usb3-phy", "brcm,ns-bx-usb3-phy".
+- reg: register mappings for DMP (Device Management Plugin) and ChipCommon B
+       MMI.
+- reg-names: "dmp" and "ccb-mii"
+
+Initialization of USB 3.0 PHY depends on Northstar version. There are currently
+three known series: Ax, Bx and Cx.
+Known A0: BCM4707 rev 0
+Known B0: BCM4707 rev 4, BCM53573 rev 2
+Known B1: BCM4707 rev 6
+Known C0: BCM47094 rev 0
+
+Example:
+	usb3-phy {
+		compatible = "brcm,ns-ax-usb3-phy";
+		reg = <0x18105000 0x1000>, <0x18003000 0x1000>;
+		reg-names = "dmp", "ccb-mii";
+		#phy-cells = <0>;
+	};

Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt

+ROCKCHIP USB2.0 PHY WITH INNO IP BLOCK
+
+Required properties (phy (parent) node):
+ - compatible : should be one of the listed compatibles:
+	* "rockchip,rk3366-usb2phy"
+	* "rockchip,rk3399-usb2phy"
+ - reg : the address offset of grf for usb-phy configuration.
+ - #clock-cells : should be 0.
+ - clock-output-names : specify the 480m output clock name.
+
+Optional properties:
+ - clocks : phandle + phy specifier pair, for the input clock of phy.
+ - clock-names : input clock name of phy, must be "phyclk".
+
+Required nodes : a sub-node is required for each port the phy provides.
+		 The sub-node name is used to identify host or otg port,
+		 and shall be the following entries:
+	* "otg-port" : the name of otg port.
+	* "host-port" : the name of host port.
+
+Required properties (port (child) node):
+ - #phy-cells : must be 0. See ./phy-bindings.txt for details.
+ - interrupts : specify an interrupt for each entry in interrupt-names.
+ - interrupt-names : a list which shall be the following entries:
+	* "otg-id" : for the otg id interrupt.
+	* "otg-bvalid" : for the otg vbus interrupt.
+	* "linestate" : for the host/otg linestate interrupt.
+
+Optional properties:
+ - phy-supply : phandle to a regulator that provides power to VBUS.
+		See ./phy-bindings.txt for details.
+
+Example:
+
+grf: syscon@ff770000 {
+	compatible = "rockchip,rk3366-grf", "syscon", "simple-mfd";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+...
+
+	u2phy: usb2-phy@700 {
+		compatible = "rockchip,rk3366-usb2phy";
+		reg = <0x700 0x2c>;
+		#clock-cells = <0>;
+		clock-output-names = "sclk_otgphy0_480m";
+
+		u2phy_otg: otg-port {
+			#phy-cells = <0>;
+			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "otg-id", "otg-bvalid", "linestate";
+			status = "okay";
+		};
+
+		u2phy_host: host-port {
+			#phy-cells = <0>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "linestate";
+			status = "okay";
+		};
+	};
+};

Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt

+* ROCKCHIP type-c PHY
+---------------------
+
+Required properties:
+ - compatible : must be "rockchip,rk3399-typec-phy"
+ - reg: Address and length of the usb phy control register set
+ - rockchip,grf : phandle to the syscon managing the "general
+   register files"
+ - clocks : phandle + clock specifier for the phy clocks
+ - clock-names : string, clock name, must be "tcpdcore", "tcpdphy-ref";
+ - assigned-clocks: main clock, should be <&cru SCLK_UPHY0_TCPDCORE> or
+		    <&cru SCLK_UPHY1_TCPDCORE>;
+ - assigned-clock-rates : the phy core clk frequency, shall be: 50000000
+ - resets : a list of phandle + reset specifier pairs
+ - reset-names : string reset name, must be:
+		 "uphy", "uphy-pipe", "uphy-tcphy"
+ - extcon : extcon specifier for the Power Delivery
+
+Note, there are 2 type-c phys for RK3399, and they are almost identical, except
+these registers(description below), every register node contains 3 sections:
+offset, enable bit, write mask bit.
+ - rockchip,typec-conn-dir : the register of type-c connector direction,
+   for type-c phy0, it must be <0xe580 0 16>;
+   for type-c phy1, it must be <0xe58c 0 16>;
+ - rockchip,usb3tousb2-en : the register of type-c force usb3 to usb2 enable
+   control.
+   for type-c phy0, it must be <0xe580 3 19>;
+   for type-c phy1, it must be <0xe58c 3 19>;
+ - rockchip,external-psm : the register of type-c phy external psm clock
+   selection.
+   for type-c phy0, it must be <0xe588 14 30>;
+   for type-c phy1, it must be <0xe594 14 30>;
+ - rockchip,pipe-status : the register of type-c phy pipe status.
+   for type-c phy0, it must be <0xe5c0 0 0>;
+   for type-c phy1, it must be <0xe5c0 16 16>;
+
+Required nodes : a sub-node is required for each port the phy provides.
+		 The sub-node name is used to identify dp or usb3 port,
+		 and shall be the following entries:
+	* "dp-port" : the name of DP port.
+	* "usb3-port" : the name of USB3 port.
+
+Required properties (port (child) node):
+- #phy-cells : must be 0, See ./phy-bindings.txt for details.
+
+Example:
+	tcphy0: phy@ff7c0000 {
+		compatible = "rockchip,rk3399-typec-phy";
+		reg = <0x0 0xff7c0000 0x0 0x40000>;
+		rockchip,grf = <&grf>;
+		extcon = <&fusb0>;
+		clocks = <&cru SCLK_UPHY0_TCPDCORE>,
+			 <&cru SCLK_UPHY0_TCPDPHY_REF>;
+		clock-names = "tcpdcore", "tcpdphy-ref";
+		assigned-clocks = <&cru SCLK_UPHY0_TCPDCORE>;
+		assigned-clock-rates = <50000000>;
+		resets = <&cru SRST_UPHY0>,
+			 <&cru SRST_UPHY0_PIPE_L00>,
+			 <&cru SRST_P_UPHY0_TCPHY>;
+		reset-names = "uphy", "uphy-pipe", "uphy-tcphy";
+		rockchip,typec-conn-dir = <0xe580 0 16>;
+		rockchip,usb3tousb2-en = <0xe580 3 19>;
+		rockchip,external-psm = <0xe588 14 30>;
+		rockchip,pipe-status = <0xe5c0 0 0>;
+
+		tcphy0_dp: dp-port {
+			#phy-cells = <0>;
+		};
+
+		tcphy0_usb3: usb3-port {
+			#phy-cells = <0>;
+		};
+	};
+
+	tcphy1: phy@ff800000 {
+		compatible = "rockchip,rk3399-typec-phy";
+		reg = <0x0 0xff800000 0x0 0x40000>;
+		rockchip,grf = <&grf>;
+		extcon = <&fusb1>;
+		clocks = <&cru SCLK_UPHY1_TCPDCORE>,
+			 <&cru SCLK_UPHY1_TCPDPHY_REF>;
+		clock-names = "tcpdcore", "tcpdphy-ref";
+		assigned-clocks = <&cru SCLK_UPHY1_TCPDCORE>;
+		assigned-clock-rates = <50000000>;
+		resets = <&cru SRST_UPHY1>,
+			 <&cru SRST_UPHY1_PIPE_L00>,
+			 <&cru SRST_P_UPHY1_TCPHY>;
+		reset-names = "uphy", "uphy-pipe", "uphy-tcphy";
+		rockchip,typec-conn-dir = <0xe58c 0 16>;
+		rockchip,usb3tousb2-en = <0xe58c 3 19>;
+		rockchip,external-psm = <0xe594 14 30>;
+		rockchip,pipe-status = <0xe5c0 16 16>;
+
+		tcphy1_dp: dp-port {
+			#phy-cells = <0>;
+		};
+
+		tcphy1_usb3: usb3-port {
+			#phy-cells = <0>;
+		};
+	};

Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt

@@ -5,6 +5,8 @@ This file provides information on what the device node for the R-Car generation
 
 Required properties:
 - compatible: "renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795
+	      SoC.
+	      "renesas,usb2-phy-r8a7796" if the device is a part of an R8A7796
 	      SoC.
 	      "renesas,rcar-gen3-usb2-phy" for a generic R-Car Gen3 compatible device.
 
@@ -30,11 +32,11 @@ Example (R-Car H3):
 		compatible = "renesas,usb2-phy-r8a7795", "renesas,rcar-gen3-usb2-phy";
 		reg = <0 0xee080200 0 0x700>;
 		interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&mstp7_clks R8A7795_CLK_EHCI0>;
+		clocks = <&cpg CPG_MOD 703>;
 	};
 
 	usb-phy@ee0a0200 {
 		compatible = "renesas,usb2-phy-r8a7795", "renesas,rcar-gen3-usb2-phy";
 		reg = <0 0xee0a0200 0 0x700>;
-		clocks = <&mstp7_clks R8A7795_CLK_EHCI0>;
+		clocks = <&cpg CPG_MOD 702>;
 	};

Documentation/devicetree/bindings/phy/rockchip-pcie-phy.txt

+Rockchip PCIE PHY
+-----------------------
+
+Required properties:
+ - compatible: rockchip,rk3399-pcie-phy
+ - #phy-cells: must be 0
+ - clocks: Must contain an entry in clock-names.
+	See ../clocks/clock-bindings.txt for details.
+ - clock-names: Must be "refclk"
+ - resets: Must contain an entry in reset-names.
+	See ../reset/reset.txt for details.
+ - reset-names: Must be "phy"
+
+Example:
+
+grf: syscon@ff770000 {
+	compatible = "rockchip,rk3399-grf", "syscon", "simple-mfd";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	...
+
+	pcie_phy: pcie-phy {
+		compatible = "rockchip,rk3399-pcie-phy";
+		#phy-cells = <0>;
+		clocks = <&cru SCLK_PCIEPHY_REF>;
+		clock-names = "refclk";
+		resets = <&cru SRST_PCIEPHY>;
+		reset-names = "phy";
+	};
+};

Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt

@@ -27,6 +27,9 @@ Optional Properties:
 - clocks : phandle + clock specifier for the phy clocks
 - clock-names: string, clock name, must be "phyclk"
 - #clock-cells: for users of the phy-pll, should be 0
+- reset-names: Only allow the following entries:
+ - phy-reset
+- resets: Must contain an entry for each entry in reset-names.
 
 Example:
 

Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt

@@ -10,6 +10,7 @@ Required properties:
   * allwinner,sun8i-a23-usb-phy
   * allwinner,sun8i-a33-usb-phy
   * allwinner,sun8i-h3-usb-phy
+  * allwinner,sun50i-a64-usb-phy
 - reg : a list of offset + length pairs
 - reg-names :
   * "phy_ctrl"

Documentation/devicetree/bindings/phy/ti-phy.txt

@@ -31,6 +31,8 @@ OMAP USB2 PHY
 
 Required properties:
  - compatible: Should be "ti,omap-usb2"
+	       Should be "ti,dra7x-usb2" for the 1st instance of USB2 PHY on
+	       DRA7x
 	       Should be "ti,dra7x-usb2-phy2" for the 2nd instance of USB2 PHY
 	       in DRA7x
  - reg : Address and length of the register set for the device.

drivers/extcon/extcon-gpio.c

@@ -49,6 +49,7 @@ static void gpio_extcon_work(struct work_struct *work)
 	state = gpiod_get_value_cansleep(data->id_gpiod);
 	if (data->pdata->gpio_active_low)
 		state = !state;
+
 	extcon_set_state_sync(data->edev, data->pdata->extcon_id, state);
 }
 

drivers/phy/Kconfig

@@ -24,6 +24,15 @@ config PHY_BCM_NS_USB2
 	  Enable this to support Broadcom USB 2.0 PHY connected to the USB
 	  controller on Northstar family.
 
+config PHY_BCM_NS_USB3
+	tristate "Broadcom Northstar USB 3.0 PHY Driver"
+	depends on ARCH_BCM_IPROC || COMPILE_TEST
+	depends on HAS_IOMEM && OF
+	select GENERIC_PHY
+	help
+	  Enable this to support Broadcom USB 3.0 PHY connected to the USB
+	  controller on Northstar family.
+
 config PHY_BERLIN_USB
 	tristate "Marvell Berlin USB PHY Driver"
 	depends on ARCH_BERLIN && RESET_CONTROLLER && HAS_IOMEM && OF
@@ -258,7 +267,9 @@ config PHY_SUN4I_USB
 	depends on RESET_CONTROLLER
 	depends on EXTCON
 	depends on POWER_SUPPLY
+	depends on USB_SUPPORT
 	select GENERIC_PHY
+	select USB_COMMON
 	help
 	  Enable this to support the transceiver that is part of Allwinner
 	  sunxi SoCs.
@@ -358,6 +369,14 @@ config PHY_ROCKCHIP_USB
 	help
 	  Enable this to support the Rockchip USB 2.0 PHY.
 
+config PHY_ROCKCHIP_INNO_USB2
+	tristate "Rockchip INNO USB2PHY Driver"
+	depends on (ARCH_ROCKCHIP || COMPILE_TEST) && OF
+	depends on COMMON_CLK
+	select GENERIC_PHY
+	help
+	  Support for Rockchip USB2.0 PHY with Innosilicon IP block.
+
 config PHY_ROCKCHIP_EMMC
 	tristate "Rockchip EMMC PHY Driver"
 	depends on ARCH_ROCKCHIP && OF
@@ -372,6 +391,23 @@ config PHY_ROCKCHIP_DP
 	help
 	  Enable this to support the Rockchip Display Port PHY.
 
+config PHY_ROCKCHIP_PCIE
+	tristate "Rockchip PCIe PHY Driver"
+	depends on (ARCH_ROCKCHIP && OF) || COMPILE_TEST
+	select GENERIC_PHY
+	select MFD_SYSCON
+	help
+	  Enable this to support the Rockchip PCIe PHY.
+
+config PHY_ROCKCHIP_TYPEC
+	tristate "Rockchip TYPEC PHY Driver"
+	depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST)
+	select EXTCON
+	select GENERIC_PHY
+	select RESET_CONTROLLER
+	help
+	  Enable this to support the Rockchip USB TYPEC PHY.
+
 config PHY_ST_SPEAR1310_MIPHY
 	tristate "ST SPEAR1310-MIPHY driver"
 	select GENERIC_PHY

drivers/phy/Makefile

@@ -4,6 +4,7 @@
 
 obj-$(CONFIG_GENERIC_PHY)		+= phy-core.o
 obj-$(CONFIG_PHY_BCM_NS_USB2)		+= phy-bcm-ns-usb2.o
+obj-$(CONFIG_PHY_BCM_NS_USB3)		+= phy-bcm-ns-usb3.o
 obj-$(CONFIG_PHY_BERLIN_USB)		+= phy-berlin-usb.o
 obj-$(CONFIG_PHY_BERLIN_SATA)		+= phy-berlin-sata.o
 obj-$(CONFIG_PHY_DA8XX_USB)		+= phy-da8xx-usb.o
@@ -39,8 +40,11 @@ phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2)	+= phy-s5pv210-usb2.o
 obj-$(CONFIG_PHY_EXYNOS5_USBDRD)	+= phy-exynos5-usbdrd.o
 obj-$(CONFIG_PHY_QCOM_APQ8064_SATA)	+= phy-qcom-apq8064-sata.o
 obj-$(CONFIG_PHY_ROCKCHIP_USB) += phy-rockchip-usb.o
+obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2)	+= phy-rockchip-inno-usb2.o
 obj-$(CONFIG_PHY_ROCKCHIP_EMMC) += phy-rockchip-emmc.o
+obj-$(CONFIG_PHY_ROCKCHIP_PCIE) += phy-rockchip-pcie.o
 obj-$(CONFIG_PHY_ROCKCHIP_DP)		+= phy-rockchip-dp.o
+obj-$(CONFIG_PHY_ROCKCHIP_TYPEC) += phy-rockchip-typec.o
 obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA)	+= phy-qcom-ipq806x-sata.o
 obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY)	+= phy-spear1310-miphy.o
 obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY)	+= phy-spear1340-miphy.o

drivers/phy/phy-bcm-ns-usb3.c

+/*
+ * Broadcom Northstar USB 3.0 PHY Driver
+ *
+ * Copyright (C) 2016 Rafał Miłecki <rafal@milecki.pl>
+ *
+ * All magic values used for initialization (and related comments) were obtained
+ * from Broadcom's SDK:
+ * Copyright (c) Broadcom Corp, 2012
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/bcma/bcma.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+#include <linux/slab.h>
+
+#define BCM_NS_USB3_MII_MNG_TIMEOUT_US	1000	/* usecs */
+
+enum bcm_ns_family {
+	BCM_NS_UNKNOWN,
+	BCM_NS_AX,
+	BCM_NS_BX,
+};
+
+struct bcm_ns_usb3 {
+	struct device *dev;
+	enum bcm_ns_family family;
+	void __iomem *dmp;
+	void __iomem *ccb_mii;
+	struct phy *phy;
+};
+
+static const struct of_device_id bcm_ns_usb3_id_table[] = {
+	{
+		.compatible = "brcm,ns-ax-usb3-phy",
+		.data = (int *)BCM_NS_AX,
+	},
+	{
+		.compatible = "brcm,ns-bx-usb3-phy",
+		.data = (int *)BCM_NS_BX,
+	},
+	{},
+};
+MODULE_DEVICE_TABLE(of, bcm_ns_usb3_id_table);
+
+static int bcm_ns_usb3_wait_reg(struct bcm_ns_usb3 *usb3, void __iomem *addr,
+				u32 mask, u32 value, unsigned long timeout)
+{
+	unsigned long deadline = jiffies + timeout;
+	u32 val;
+
+	do {
+		val = readl(addr);
+		if ((val & mask) == value)
+			return 0;
+		cpu_relax();
+		udelay(10);
+	} while (!time_after_eq(jiffies, deadline));
+
+	dev_err(usb3->dev, "Timeout waiting for register %p\n", addr);
+
+	return -EBUSY;
+}
+
+static inline int bcm_ns_usb3_mii_mng_wait_idle(struct bcm_ns_usb3 *usb3)
+{
+	return bcm_ns_usb3_wait_reg(usb3, usb3->ccb_mii + BCMA_CCB_MII_MNG_CTL,
+				    0x0100, 0x0000,
+				    usecs_to_jiffies(BCM_NS_USB3_MII_MNG_TIMEOUT_US));
+}
+
+static int bcm_ns_usb3_mii_mng_write32(struct bcm_ns_usb3 *usb3, u32 value)
+{
+	int err;
+
+	err = bcm_ns_usb3_mii_mng_wait_idle(usb3);
+	if (err < 0) {
+		dev_err(usb3->dev, "Couldn't write 0x%08x value\n", value);
+		return err;
+	}
+
+	writel(value, usb3->ccb_mii + BCMA_CCB_MII_MNG_CMD_DATA);
+
+	return 0;
+}
+
+static int bcm_ns_usb3_phy_init_ns_bx(struct bcm_ns_usb3 *usb3)
+{
+	int err;
+
+	/* Enable MDIO. Setting MDCDIV as 26  */
+	writel(0x0000009a, usb3->ccb_mii + BCMA_CCB_MII_MNG_CTL);
+
+	/* Wait for MDIO? */
+	udelay(2);
+
+	/* USB3 PLL Block */
+	err = bcm_ns_usb3_mii_mng_write32(usb3, 0x587e8000);
+	if (err < 0)
+		return err;
+
+	/* Assert Ana_Pllseq start */
+	bcm_ns_usb3_mii_mng_write32(usb3, 0x58061000);
+
+	/* Assert CML Divider ratio to 26 */
+	bcm_ns_usb3_mii_mng_write32(usb3, 0x582a6400);
+
+	/* Asserting PLL Reset */
+	bcm_ns_usb3_mii_mng_write32(usb3, 0x582ec000);
+
+	/* Deaaserting PLL Reset */
+	bcm_ns_usb3_mii_mng_write32(usb3, 0x582e8000);
+
+	/* Waiting MII Mgt interface idle */
+	bcm_ns_usb3_mii_mng_wait_idle(usb3);
+
+	/* Deasserting USB3 system reset */
+	writel(0, usb3->dmp + BCMA_RESET_CTL);
+
+	/* PLL frequency monitor enable */
+	bcm_ns_usb3_mii_mng_write32(usb3, 0x58069000);
+
+	/* PIPE Block */
+	bcm_ns_usb3_mii_mng_write32(usb3, 0x587e8060);
+
+	/* CMPMAX & CMPMINTH setting */
+	bcm_ns_usb3_mii_mng_write32(usb3, 0x580af30d);
+
+	/* DEGLITCH MIN & MAX setting */
+	bcm_ns_usb3_mii_mng_write32(usb3, 0x580e6302);
+
+	/* TXPMD block */
+	bcm_ns_usb3_mii_mng_write32(usb3, 0x587e8040);
+
+	/* Enabling SSC */
+	bcm_ns_usb3_mii_mng_write32(usb3, 0x58061003);
+
+	/* Waiting MII Mgt interface idle */
+	bcm_ns_usb3_mii_mng_wait_idle(usb3);
+
+	return 0;
+}
+
+static int bcm_ns_usb3_phy_init_ns_ax(struct bcm_ns_usb3 *usb3)
+{
+	int err;
+
+	/* Enable MDIO. Setting MDCDIV as 26  */
+	writel(0x0000009a, usb3->ccb_mii + BCMA_CCB_MII_MNG_CTL);
+
+	/* Wait for MDIO? */
+	udelay(2);
+
+	/* PLL30 block */
+	err = bcm_ns_usb3_mii_mng_write32(usb3, 0x587e8000);
+	if (err < 0)
+		return err;
+
+	bcm_ns_usb3_mii_mng_write32(usb3, 0x582a6400);
+
+	bcm_ns_usb3_mii_mng_write32(usb3, 0x587e80e0);
+
+	bcm_ns_usb3_mii_mng_write32(usb3, 0x580a009c);
+
+	/* Enable SSC */
+	bcm_ns_usb3_mii_mng_write32(usb3, 0x587e8040);
+
+	bcm_ns_usb3_mii_mng_write32(usb3, 0x580a21d3);
+
+	bcm_ns_usb3_mii_mng_write32(usb3, 0x58061003);
+
+	/* Waiting MII Mgt interface idle */
+	bcm_ns_usb3_mii_mng_wait_idle(usb3);
+
+	/* Deasserting USB3 system reset */
+	writel(0, usb3->dmp + BCMA_RESET_CTL);
+
+	return 0;
+}
+
+static int bcm_ns_usb3_phy_init(struct phy *phy)
+{
+	struct bcm_ns_usb3 *usb3 = phy_get_drvdata(phy);
+	int err;
+
+	/* Perform USB3 system soft reset */
+	writel(BCMA_RESET_CTL_RESET, usb3->dmp + BCMA_RESET_CTL);
+
+	switch (usb3->family) {
+	case BCM_NS_AX:
+		err = bcm_ns_usb3_phy_init_ns_ax(usb3);
+		break;
+	case BCM_NS_BX:
+		err = bcm_ns_usb3_phy_init_ns_bx(usb3);
+		break;
+	default:
+		WARN_ON(1);
+		err = -ENOTSUPP;
+	}
+
+	return err;
+}
+
+static const struct phy_ops ops = {
+	.init		= bcm_ns_usb3_phy_init,
+	.owner		= THIS_MODULE,
+};
+
+static int bcm_ns_usb3_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	const struct of_device_id *of_id;
+	struct bcm_ns_usb3 *usb3;
+	struct resource *res;
+	struct phy_provider *phy_provider;
+
+	usb3 = devm_kzalloc(dev, sizeof(*usb3), GFP_KERNEL);
+	if (!usb3)
+		return -ENOMEM;
+
+	usb3->dev = dev;
+
+	of_id = of_match_device(bcm_ns_usb3_id_table, dev);
+	if (!of_id)
+		return -EINVAL;
+	usb3->family = (enum bcm_ns_family)of_id->data;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dmp");
+	usb3->dmp = devm_ioremap_resource(dev, res);
+	if (IS_ERR(usb3->dmp)) {
+		dev_err(dev, "Failed to map DMP regs\n");
+		return PTR_ERR(usb3->dmp);
+	}
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ccb-mii");
+	usb3->ccb_mii = devm_ioremap_resource(dev, res);
+	if (IS_ERR(usb3->ccb_mii)) {
+		dev_err(dev, "Failed to map ChipCommon B MII regs\n");
+		return PTR_ERR(usb3->ccb_mii);
+	}
+
+	usb3->phy = devm_phy_create(dev, NULL, &ops);
+	if (IS_ERR(usb3->phy)) {
+		dev_err(dev, "Failed to create PHY\n");
+		return PTR_ERR(usb3->phy);
+	}
+
+	phy_set_drvdata(usb3->phy, usb3);
+	platform_set_drvdata(pdev, usb3);
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (!IS_ERR(phy_provider))
+		dev_info(dev, "Registered Broadcom Northstar USB 3.0 PHY driver\n");
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static struct platform_driver bcm_ns_usb3_driver = {
+	.probe		= bcm_ns_usb3_probe,
+	.driver = {
+		.name = "bcm_ns_usb3",
+		.of_match_table = bcm_ns_usb3_id_table,
+	},
+};
+module_platform_driver(bcm_ns_usb3_driver);
+
+MODULE_LICENSE("GPL v2");

drivers/phy/phy-bcm-ns2-pcie.c

@@ -18,11 +18,6 @@
 #include <linux/phy.h>
 #include <linux/phy/phy.h>
 
-struct ns2_pci_phy {
-	struct mdio_device *mdiodev;
-	struct phy *phy;
-};
-
 #define BLK_ADDR_REG_OFFSET	0x1f
 #define PLL_AFE1_100MHZ_BLK	0x2100
 #define PLL_CLK_AMP_OFFSET	0x03
@@ -30,17 +25,17 @@ struct ns2_pci_phy {
 
 static int ns2_pci_phy_init(struct phy *p)
 {
-	struct ns2_pci_phy *phy = phy_get_drvdata(p);
+	struct mdio_device *mdiodev = phy_get_drvdata(p);
 	int rc;
 
 	/* select the AFE 100MHz block page */
-	rc = mdiobus_write(phy->mdiodev->bus, phy->mdiodev->addr,
+	rc = mdiobus_write(mdiodev->bus, mdiodev->addr,
 			   BLK_ADDR_REG_OFFSET, PLL_AFE1_100MHZ_BLK);
 	if (rc)
 		goto err;
 
 	/* set the 100 MHz reference clock amplitude to 2.05 v */
-	rc = mdiobus_write(phy->mdiodev->bus, phy->mdiodev->addr,
+	rc = mdiobus_write(mdiodev->bus, mdiodev->addr,
 			   PLL_CLK_AMP_OFFSET, PLL_CLK_AMP_2P05V);
 	if (rc)
 		goto err;
@@ -48,19 +43,19 @@ static int ns2_pci_phy_init(struct phy *p)
 	return 0;
 
 err:
-	dev_err(&phy->mdiodev->dev, "Error %d writing to phy\n", rc);
+	dev_err(&mdiodev->dev, "Error %d writing to phy\n", rc);
 	return rc;
 }
 
-static struct phy_ops ns2_pci_phy_ops = {
+static const struct phy_ops ns2_pci_phy_ops = {
 	.init = ns2_pci_phy_init,
+	.owner = THIS_MODULE,
 };
 
 static int ns2_pci_phy_probe(struct mdio_device *mdiodev)
 {
 	struct device *dev = &mdiodev->dev;
 	struct phy_provider *provider;
-	struct ns2_pci_phy *p;
 	struct phy *phy;
 
 	phy = devm_phy_create(dev, dev->of_node, &ns2_pci_phy_ops);
@@ -69,16 +64,7 @@ static int ns2_pci_phy_probe(struct mdio_device *mdiodev)
 		return PTR_ERR(phy);
 	}
 
-	p = devm_kmalloc(dev, sizeof(struct ns2_pci_phy),
-			 GFP_KERNEL);
-	if (!p)
-		return -ENOMEM;
-
-	p->mdiodev = mdiodev;
-	dev_set_drvdata(dev, p);
-
-	p->phy = phy;
-	phy_set_drvdata(phy, p);
+	phy_set_drvdata(phy, mdiodev);
 
 	provider = devm_of_phy_provider_register(&phy->dev,
 						 of_phy_simple_xlate);

drivers/phy/phy-core.c

@@ -357,6 +357,21 @@ int phy_set_mode(struct phy *phy, enum phy_mode mode)
 }
 EXPORT_SYMBOL_GPL(phy_set_mode);
 
+int phy_reset(struct phy *phy)
+{
+	int ret;
+
+	if (!phy || !phy->ops->reset)
+		return 0;
+
+	mutex_lock(&phy->mutex);
+	ret = phy->ops->reset(phy);
+	mutex_unlock(&phy->mutex);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(phy_reset);
+
 /**
  * _of_phy_get() - lookup and obtain a reference to a phy by phandle
  * @np: device_node for which to get the phy

drivers/phy/phy-da8xx-usb.c

@@ -154,7 +154,7 @@ static int da8xx_usb_phy_probe(struct platform_device *pdev)
 		d_phy->regmap = syscon_regmap_lookup_by_compatible(
 							"ti,da830-cfgchip");
 	else
-		d_phy->regmap = syscon_regmap_lookup_by_pdevname("syscon.0");
+		d_phy->regmap = syscon_regmap_lookup_by_pdevname("syscon");
 	if (IS_ERR(d_phy->regmap)) {
 		dev_err(dev, "Failed to get syscon\n");
 		return PTR_ERR(d_phy->regmap);

drivers/phy/phy-exynos5-usbdrd.c

@@ -249,7 +249,7 @@ static void exynos5_usbdrd_phy_isol(struct phy_usb_instance *inst,
 static unsigned int
 exynos5_usbdrd_pipe3_set_refclk(struct phy_usb_instance *inst)
 {
-	static u32 reg;
+	u32 reg;
 	struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
 
 	/* restore any previous reference clock settings */
@@ -295,7 +295,7 @@ exynos5_usbdrd_pipe3_set_refclk(struct phy_usb_instance *inst)
 static unsigned int
 exynos5_usbdrd_utmi_set_refclk(struct phy_usb_instance *inst)
 {
-	static u32 reg;
+	u32 reg;
 	struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
 
 	/* restore any previous reference clock settings */

drivers/phy/phy-omap-usb2.c

@@ -133,11 +133,49 @@ static int omap_usb_power_on(struct phy *x)
 	return omap_usb_phy_power(phy, true);
 }
 
+static int omap_usb2_disable_clocks(struct omap_usb *phy)
+{
+	clk_disable(phy->wkupclk);
+	if (!IS_ERR(phy->optclk))
+		clk_disable(phy->optclk);
+
+	return 0;
+}
+
+static int omap_usb2_enable_clocks(struct omap_usb *phy)
+{
+	int ret;
+
+	ret = clk_enable(phy->wkupclk);
+	if (ret < 0) {
+		dev_err(phy->dev, "Failed to enable wkupclk %d\n", ret);
+		goto err0;
+	}
+
+	if (!IS_ERR(phy->optclk)) {
+		ret = clk_enable(phy->optclk);
+		if (ret < 0) {
+			dev_err(phy->dev, "Failed to enable optclk %d\n", ret);
+			goto err1;
+		}
+	}
+
+	return 0;
+
+err1:
+	clk_disable(phy->wkupclk);
+
+err0:
+	return ret;
+}
+
 static int omap_usb_init(struct phy *x)
 {
 	struct omap_usb *phy = phy_get_drvdata(x);
 	u32 val;
 
+	omap_usb2_enable_clocks(phy);
+
 	if (phy->flags & OMAP_USB2_CALIBRATE_FALSE_DISCONNECT) {
 		/*
 		 *
@@ -155,8 +193,16 @@ static int omap_usb_init(struct phy *x)
 	return 0;
 }
 
+static int omap_usb_exit(struct phy *x)
+{
+	struct omap_usb *phy = phy_get_drvdata(x);
+
+	return omap_usb2_disable_clocks(phy);
+}
+
 static const struct phy_ops ops = {
 	.init		= omap_usb_init,
+	.exit		= omap_usb_exit,
 	.power_on	= omap_usb_power_on,
 	.power_off	= omap_usb_power_off,
 	.owner		= THIS_MODULE,
@@ -376,65 +422,11 @@ static int omap_usb2_remove(struct platform_device *pdev)
 	return 0;
 }
 
-#ifdef CONFIG_PM
-
-static int omap_usb2_runtime_suspend(struct device *dev)
-{
-	struct platform_device	*pdev = to_platform_device(dev);
-	struct omap_usb	*phy = platform_get_drvdata(pdev);
-
-	clk_disable(phy->wkupclk);
-	if (!IS_ERR(phy->optclk))
-		clk_disable(phy->optclk);
-
-	return 0;
-}
-
-static int omap_usb2_runtime_resume(struct device *dev)
-{
-	struct platform_device	*pdev = to_platform_device(dev);
-	struct omap_usb	*phy = platform_get_drvdata(pdev);
-	int ret;
-
-	ret = clk_enable(phy->wkupclk);
-	if (ret < 0) {
-		dev_err(phy->dev, "Failed to enable wkupclk %d\n", ret);
-		goto err0;
-	}
-
-	if (!IS_ERR(phy->optclk)) {
-		ret = clk_enable(phy->optclk);
-		if (ret < 0) {
-			dev_err(phy->dev, "Failed to enable optclk %d\n", ret);
-			goto err1;
-		}
-	}
-
-	return 0;
-
-err1:
-	clk_disable(phy->wkupclk);
-
-err0:
-	return ret;
-}
-
-static const struct dev_pm_ops omap_usb2_pm_ops = {
-	SET_RUNTIME_PM_OPS(omap_usb2_runtime_suspend, omap_usb2_runtime_resume,
-		NULL)
-};
-
-#define DEV_PM_OPS     (&omap_usb2_pm_ops)
-#else
-#define DEV_PM_OPS     NULL
-#endif
-
 static struct platform_driver omap_usb2_driver = {
 	.probe		= omap_usb2_probe,
 	.remove		= omap_usb2_remove,
 	.driver		= {
 		.name	= "omap-usb2",
-		.pm	= DEV_PM_OPS,
 		.of_match_table = omap_usb2_id_table,
 	},
 };

drivers/phy/phy-qcom-ufs.c

@@ -283,10 +283,8 @@ static int __ufs_qcom_phy_init_vreg(struct phy *phy,
 			err = 0;
 		}
 		snprintf(prop_name, MAX_PROP_NAME, "%s-always-on", name);
-		if (of_get_property(dev->of_node, prop_name, NULL))
-			vreg->is_always_on = true;
-		else
-			vreg->is_always_on = false;
+		vreg->is_always_on = of_property_read_bool(dev->of_node,
+							   prop_name);
 	}
 
 	if (!strcmp(name, "vdda-pll")) {

drivers/phy/phy-rcar-gen3-usb2.c

@@ -280,6 +280,7 @@ static irqreturn_t rcar_gen3_phy_usb2_irq(int irq, void *_ch)
 
 static const struct of_device_id rcar_gen3_phy_usb2_match_table[] = {
 	{ .compatible = "renesas,usb2-phy-r8a7795" },
+	{ .compatible = "renesas,usb2-phy-r8a7796" },
 	{ .compatible = "renesas,rcar-gen3-usb2-phy" },
 	{ }
 };

drivers/phy/phy-rockchip-inno-usb2.c

+/*
+ * Rockchip USB2.0 PHY with Innosilicon IP block driver
+ *
+ * Copyright (C) 2016 Fuzhou Rockchip Electronics Co., Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/gpio/consumer.h>
+#include <linux/jiffies.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/mfd/syscon.h>
+
+#define BIT_WRITEABLE_SHIFT	16
+#define SCHEDULE_DELAY	(60 * HZ)
+
+enum rockchip_usb2phy_port_id {
+	USB2PHY_PORT_OTG,
+	USB2PHY_PORT_HOST,
+	USB2PHY_NUM_PORTS,
+};
+
+enum rockchip_usb2phy_host_state {
+	PHY_STATE_HS_ONLINE	= 0,
+	PHY_STATE_DISCONNECT	= 1,
+	PHY_STATE_CONNECT	= 2,
+	PHY_STATE_FS_LS_ONLINE	= 4,
+};
+
+struct usb2phy_reg {
+	unsigned int	offset;
+	unsigned int	bitend;
+	unsigned int	bitstart;
+	unsigned int	disable;
+	unsigned int	enable;
+};
+
+/**
+ * struct rockchip_usb2phy_port_cfg: usb-phy port configuration.
+ * @phy_sus: phy suspend register.
+ * @ls_det_en: linestate detection enable register.
+ * @ls_det_st: linestate detection state register.
+ * @ls_det_clr: linestate detection clear register.
+ * @utmi_ls: utmi linestate state register.
+ * @utmi_hstdet: utmi host disconnect register.
+ */
+struct rockchip_usb2phy_port_cfg {
+	struct usb2phy_reg	phy_sus;
+	struct usb2phy_reg	ls_det_en;
+	struct usb2phy_reg	ls_det_st;
+	struct usb2phy_reg	ls_det_clr;
+	struct usb2phy_reg	utmi_ls;
+	struct usb2phy_reg	utmi_hstdet;
+};
+
+/**
+ * struct rockchip_usb2phy_cfg: usb-phy configuration.
+ * @reg: the address offset of grf for usb-phy config.
+ * @num_ports: specify how many ports that the phy has.
+ * @clkout_ctl: keep on/turn off output clk of phy.
+ */
+struct rockchip_usb2phy_cfg {
+	unsigned int	reg;
+	unsigned int	num_ports;
+	struct usb2phy_reg	clkout_ctl;
+	const struct rockchip_usb2phy_port_cfg	port_cfgs[USB2PHY_NUM_PORTS];
+};
+
+/**
+ * struct rockchip_usb2phy_port: usb-phy port data.
+ * @port_id: flag for otg port or host port.
+ * @suspended: phy suspended flag.
+ * @ls_irq: IRQ number assigned for linestate detection.
+ * @mutex: for register updating in sm_work.
+ * @sm_work: OTG state machine work.
+ * @phy_cfg: port register configuration, assigned by driver data.
+ */
+struct rockchip_usb2phy_port {
+	struct phy	*phy;
+	unsigned int	port_id;
+	bool		suspended;
+	int		ls_irq;
+	struct mutex	mutex;
+	struct		delayed_work sm_work;
+	const struct	rockchip_usb2phy_port_cfg *port_cfg;
+};
+
+/**
+ * struct rockchip_usb2phy: usb2.0 phy driver data.
+ * @grf: General Register Files regmap.
+ * @clk: clock struct of phy input clk.
+ * @clk480m: clock struct of phy output clk.
+ * @clk_hw: clock struct of phy output clk management.
+ * @phy_cfg: phy register configuration, assigned by driver data.
+ * @ports: phy port instance.
+ */
+struct rockchip_usb2phy {
+	struct device	*dev;
+	struct regmap	*grf;
+	struct clk	*clk;
+	struct clk	*clk480m;
+	struct clk_hw	clk480m_hw;
+	const struct rockchip_usb2phy_cfg	*phy_cfg;
+	struct rockchip_usb2phy_port	ports[USB2PHY_NUM_PORTS];
+};
+
+static inline int property_enable(struct rockchip_usb2phy *rphy,
+				  const struct usb2phy_reg *reg, bool en)
+{
+	unsigned int val, mask, tmp;
+
+	tmp = en ? reg->enable : reg->disable;
+	mask = GENMASK(reg->bitend, reg->bitstart);
+	val = (tmp << reg->bitstart) | (mask << BIT_WRITEABLE_SHIFT);
+
+	return regmap_write(rphy->grf, reg->offset, val);
+}
+
+static inline bool property_enabled(struct rockchip_usb2phy *rphy,
+				    const struct usb2phy_reg *reg)
+{
+	int ret;
+	unsigned int tmp, orig;
+	unsigned int mask = GENMASK(reg->bitend, reg->bitstart);
+
+	ret = regmap_read(rphy->grf, reg->offset, &orig);
+	if (ret)
+		return false;
+
+	tmp = (orig & mask) >> reg->bitstart;
+	return tmp == reg->enable;
+}
+
+static int rockchip_usb2phy_clk480m_enable(struct clk_hw *hw)
+{
+	struct rockchip_usb2phy *rphy =
+		container_of(hw, struct rockchip_usb2phy, clk480m_hw);
+	int ret;
+
+	/* turn on 480m clk output if it is off */
+	if (!property_enabled(rphy, &rphy->phy_cfg->clkout_ctl)) {
+		ret = property_enable(rphy, &rphy->phy_cfg->clkout_ctl, true);
+		if (ret)
+			return ret;
+
+		/* waitting for the clk become stable */
+		mdelay(1);
+	}
+
+	return 0;
+}
+
+static void rockchip_usb2phy_clk480m_disable(struct clk_hw *hw)
+{
+	struct rockchip_usb2phy *rphy =
+		container_of(hw, struct rockchip_usb2phy, clk480m_hw);
+
+	/* turn off 480m clk output */
+	property_enable(rphy, &rphy->phy_cfg->clkout_ctl, false);
+}
+
+static int rockchip_usb2phy_clk480m_enabled(struct clk_hw *hw)
+{
+	struct rockchip_usb2phy *rphy =
+		container_of(hw, struct rockchip_usb2phy, clk480m_hw);
+
+	return property_enabled(rphy, &rphy->phy_cfg->clkout_ctl);
+}
+
+static unsigned long
+rockchip_usb2phy_clk480m_recalc_rate(struct clk_hw *hw,
+				     unsigned long parent_rate)
+{
+	return 480000000;
+}
+
+static const struct clk_ops rockchip_usb2phy_clkout_ops = {
+	.enable = rockchip_usb2phy_clk480m_enable,
+	.disable = rockchip_usb2phy_clk480m_disable,
+	.is_enabled = rockchip_usb2phy_clk480m_enabled,
+	.recalc_rate = rockchip_usb2phy_clk480m_recalc_rate,
+};
+
+static void rockchip_usb2phy_clk480m_unregister(void *data)
+{
+	struct rockchip_usb2phy *rphy = data;
+
+	of_clk_del_provider(rphy->dev->of_node);
+	clk_unregister(rphy->clk480m);
+}
+
+static int
+rockchip_usb2phy_clk480m_register(struct rockchip_usb2phy *rphy)
+{
+	struct device_node *node = rphy->dev->of_node;
+	struct clk_init_data init;
+	const char *clk_name;
+	int ret;
+
+	init.flags = 0;
+	init.name = "clk_usbphy_480m";
+	init.ops = &rockchip_usb2phy_clkout_ops;
+
+	/* optional override of the clockname */
+	of_property_read_string(node, "clock-output-names", &init.name);
+
+	if (rphy->clk) {
+		clk_name = __clk_get_name(rphy->clk);
+		init.parent_names = &clk_name;
+		init.num_parents = 1;
+	} else {
+		init.parent_names = NULL;
+		init.num_parents = 0;
+	}
+
+	rphy->clk480m_hw.init = &init;
+
+	/* register the clock */
+	rphy->clk480m = clk_register(rphy->dev, &rphy->clk480m_hw);
+	if (IS_ERR(rphy->clk480m)) {
+		ret = PTR_ERR(rphy->clk480m);
+		goto err_ret;
+	}
+
+	ret = of_clk_add_provider(node, of_clk_src_simple_get, rphy->clk480m);
+	if (ret < 0)
+		goto err_clk_provider;
+
+	ret = devm_add_action(rphy->dev, rockchip_usb2phy_clk480m_unregister,
+			      rphy);
+	if (ret < 0)
+		goto err_unreg_action;
+
+	return 0;
+
+err_unreg_action:
+	of_clk_del_provider(node);
+err_clk_provider:
+	clk_unregister(rphy->clk480m);
+err_ret:
+	return ret;
+}
+
+static int rockchip_usb2phy_init(struct phy *phy)
+{
+	struct rockchip_usb2phy_port *rport = phy_get_drvdata(phy);
+	struct rockchip_usb2phy *rphy = dev_get_drvdata(phy->dev.parent);
+	int ret;
+
+	if (rport->port_id == USB2PHY_PORT_HOST) {
+		/* clear linestate and enable linestate detect irq */
+		mutex_lock(&rport->mutex);
+
+		ret = property_enable(rphy, &rport->port_cfg->ls_det_clr, true);
+		if (ret) {
+			mutex_unlock(&rport->mutex);
+			return ret;
+		}
+
+		ret = property_enable(rphy, &rport->port_cfg->ls_det_en, true);
+		if (ret) {
+			mutex_unlock(&rport->mutex);
+			return ret;
+		}
+
+		mutex_unlock(&rport->mutex);
+		schedule_delayed_work(&rport->sm_work, SCHEDULE_DELAY);
+	}
+
+	return 0;
+}
+
+static int rockchip_usb2phy_power_on(struct phy *phy)
+{
+	struct rockchip_usb2phy_port *rport = phy_get_drvdata(phy);
+	struct rockchip_usb2phy *rphy = dev_get_drvdata(phy->dev.parent);
+	int ret;
+
+	dev_dbg(&rport->phy->dev, "port power on\n");
+
+	if (!rport->suspended)
+		return 0;
+
+	ret = clk_prepare_enable(rphy->clk480m);
+	if (ret)
+		return ret;
+
+	ret = property_enable(rphy, &rport->port_cfg->phy_sus, false);
+	if (ret)
+		return ret;
+
+	rport->suspended = false;
+	return 0;
+}
+
+static int rockchip_usb2phy_power_off(struct phy *phy)
+{
+	struct rockchip_usb2phy_port *rport = phy_get_drvdata(phy);
+	struct rockchip_usb2phy *rphy = dev_get_drvdata(phy->dev.parent);
+	int ret;
+
+	dev_dbg(&rport->phy->dev, "port power off\n");
+
+	if (rport->suspended)
+		return 0;
+
+	ret = property_enable(rphy, &rport->port_cfg->phy_sus, true);
+	if (ret)
+		return ret;
+
+	rport->suspended = true;
+	clk_disable_unprepare(rphy->clk480m);
+
+	return 0;
+}
+
+static int rockchip_usb2phy_exit(struct phy *phy)
+{
+	struct rockchip_usb2phy_port *rport = phy_get_drvdata(phy);
+
+	if (rport->port_id == USB2PHY_PORT_HOST)
+		cancel_delayed_work_sync(&rport->sm_work);
+
+	return 0;
+}
+
+static const struct phy_ops rockchip_usb2phy_ops = {
+	.init		= rockchip_usb2phy_init,
+	.exit		= rockchip_usb2phy_exit,
+	.power_on	= rockchip_usb2phy_power_on,
+	.power_off	= rockchip_usb2phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+/*
+ * The function manage host-phy port state and suspend/resume phy port
+ * to save power.
+ *
+ * we rely on utmi_linestate and utmi_hostdisconnect to identify whether
+ * devices is disconnect or not. Besides, we do not need care it is FS/LS
+ * disconnected or HS disconnected, actually, we just only need get the
+ * device is disconnected at last through rearm the delayed work,
+ * to suspend the phy port in _PHY_STATE_DISCONNECT_ case.
+ *
+ * NOTE: It may invoke *phy_powr_off or *phy_power_on which will invoke
+ * some clk related APIs, so do not invoke it from interrupt context directly.
+ */
+static void rockchip_usb2phy_sm_work(struct work_struct *work)
+{
+	struct rockchip_usb2phy_port *rport =
+		container_of(work, struct rockchip_usb2phy_port, sm_work.work);
+	struct rockchip_usb2phy *rphy = dev_get_drvdata(rport->phy->dev.parent);
+	unsigned int sh = rport->port_cfg->utmi_hstdet.bitend -
+			  rport->port_cfg->utmi_hstdet.bitstart + 1;
+	unsigned int ul, uhd, state;
+	unsigned int ul_mask, uhd_mask;
+	int ret;
+
+	mutex_lock(&rport->mutex);
+
+	ret = regmap_read(rphy->grf, rport->port_cfg->utmi_ls.offset, &ul);
+	if (ret < 0)
+		goto next_schedule;
+
+	ret = regmap_read(rphy->grf, rport->port_cfg->utmi_hstdet.offset,
+			  &uhd);
+	if (ret < 0)
+		goto next_schedule;
+
+	uhd_mask = GENMASK(rport->port_cfg->utmi_hstdet.bitend,
+			   rport->port_cfg->utmi_hstdet.bitstart);
+	ul_mask = GENMASK(rport->port_cfg->utmi_ls.bitend,
+			  rport->port_cfg->utmi_ls.bitstart);
+
+	/* stitch on utmi_ls and utmi_hstdet as phy state */
+	state = ((uhd & uhd_mask) >> rport->port_cfg->utmi_hstdet.bitstart) |
+		(((ul & ul_mask) >> rport->port_cfg->utmi_ls.bitstart) << sh);
+
+	switch (state) {
+	case PHY_STATE_HS_ONLINE:
+		dev_dbg(&rport->phy->dev, "HS online\n");
+		break;
+	case PHY_STATE_FS_LS_ONLINE:
+		/*
+		 * For FS/LS device, the online state share with connect state
+		 * from utmi_ls and utmi_hstdet register, so we distinguish
+		 * them via suspended flag.
+		 *
+		 * Plus, there are two cases, one is D- Line pull-up, and D+
+		 * line pull-down, the state is 4; another is D+ line pull-up,
+		 * and D- line pull-down, the state is 2.
+		 */
+		if (!rport->suspended) {
+			/* D- line pull-up, D+ line pull-down */
+			dev_dbg(&rport->phy->dev, "FS/LS online\n");
+			break;
+		}
+		/* fall through */
+	case PHY_STATE_CONNECT:
+		if (rport->suspended) {
+			dev_dbg(&rport->phy->dev, "Connected\n");
+			rockchip_usb2phy_power_on(rport->phy);
+			rport->suspended = false;
+		} else {
+			/* D+ line pull-up, D- line pull-down */
+			dev_dbg(&rport->phy->dev, "FS/LS online\n");
+		}
+		break;
+	case PHY_STATE_DISCONNECT:
+		if (!rport->suspended) {
+			dev_dbg(&rport->phy->dev, "Disconnected\n");
+			rockchip_usb2phy_power_off(rport->phy);
+			rport->suspended = true;
+		}
+
+		/*
+		 * activate the linestate detection to get the next device
+		 * plug-in irq.
+		 */
+		property_enable(rphy, &rport->port_cfg->ls_det_clr, true);
+		property_enable(rphy, &rport->port_cfg->ls_det_en, true);
+
+		/*
+		 * we don't need to rearm the delayed work when the phy port
+		 * is suspended.
+		 */
+		mutex_unlock(&rport->mutex);
+		return;
+	default:
+		dev_dbg(&rport->phy->dev, "unknown phy state\n");
+		break;
+	}
+
+next_schedule:
+	mutex_unlock(&rport->mutex);
+	schedule_delayed_work(&rport->sm_work, SCHEDULE_DELAY);
+}
+
+static irqreturn_t rockchip_usb2phy_linestate_irq(int irq, void *data)
+{
+	struct rockchip_usb2phy_port *rport = data;
+	struct rockchip_usb2phy *rphy = dev_get_drvdata(rport->phy->dev.parent);
+
+	if (!property_enabled(rphy, &rport->port_cfg->ls_det_st))
+		return IRQ_NONE;
+
+	mutex_lock(&rport->mutex);
+
+	/* disable linestate detect irq and clear its status */
+	property_enable(rphy, &rport->port_cfg->ls_det_en, false);
+	property_enable(rphy, &rport->port_cfg->ls_det_clr, true);
+
+	mutex_unlock(&rport->mutex);
+
+	/*
+	 * In this case for host phy port, a new device is plugged in,
+	 * meanwhile, if the phy port is suspended, we need rearm the work to
+	 * resume it and mange its states; otherwise, we do nothing about that.
+	 */
+	if (rport->suspended && rport->port_id == USB2PHY_PORT_HOST)
+		rockchip_usb2phy_sm_work(&rport->sm_work.work);
+
+	return IRQ_HANDLED;
+}
+
+static int rockchip_usb2phy_host_port_init(struct rockchip_usb2phy *rphy,
+					   struct rockchip_usb2phy_port *rport,
+					   struct device_node *child_np)
+{
+	int ret;
+
+	rport->port_id = USB2PHY_PORT_HOST;
+	rport->port_cfg = &rphy->phy_cfg->port_cfgs[USB2PHY_PORT_HOST];
+	rport->suspended = true;
+
+	mutex_init(&rport->mutex);
+	INIT_DELAYED_WORK(&rport->sm_work, rockchip_usb2phy_sm_work);
+
+	rport->ls_irq = of_irq_get_byname(child_np, "linestate");
+	if (rport->ls_irq < 0) {
+		dev_err(rphy->dev, "no linestate irq provided\n");
+		return rport->ls_irq;
+	}
+
+	ret = devm_request_threaded_irq(rphy->dev, rport->ls_irq, NULL,
+					rockchip_usb2phy_linestate_irq,
+					IRQF_ONESHOT,
+					"rockchip_usb2phy", rport);
+	if (ret) {
+		dev_err(rphy->dev, "failed to request irq handle\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int rockchip_usb2phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct device_node *child_np;
+	struct phy_provider *provider;
+	struct rockchip_usb2phy *rphy;
+	const struct rockchip_usb2phy_cfg *phy_cfgs;
+	const struct of_device_id *match;
+	unsigned int reg;
+	int index, ret;
+
+	rphy = devm_kzalloc(dev, sizeof(*rphy), GFP_KERNEL);
+	if (!rphy)
+		return -ENOMEM;
+
+	match = of_match_device(dev->driver->of_match_table, dev);
+	if (!match || !match->data) {
+		dev_err(dev, "phy configs are not assigned!\n");
+		return -EINVAL;
+	}
+
+	if (!dev->parent || !dev->parent->of_node)
+		return -EINVAL;
+
+	rphy->grf = syscon_node_to_regmap(dev->parent->of_node);
+	if (IS_ERR(rphy->grf))
+		return PTR_ERR(rphy->grf);
+
+	if (of_property_read_u32(np, "reg", &reg)) {
+		dev_err(dev, "the reg property is not assigned in %s node\n",
+			np->name);
+		return -EINVAL;
+	}
+
+	rphy->dev = dev;
+	phy_cfgs = match->data;
+	platform_set_drvdata(pdev, rphy);
+
+	/* find out a proper config which can be matched with dt. */
+	index = 0;
+	while (phy_cfgs[index].reg) {
+		if (phy_cfgs[index].reg == reg) {
+			rphy->phy_cfg = &phy_cfgs[index];
+			break;
+		}
+
+		++index;
+	}
+
+	if (!rphy->phy_cfg) {
+		dev_err(dev, "no phy-config can be matched with %s node\n",
+			np->name);
+		return -EINVAL;
+	}
+
+	rphy->clk = of_clk_get_by_name(np, "phyclk");
+	if (!IS_ERR(rphy->clk)) {
+		clk_prepare_enable(rphy->clk);
+	} else {
+		dev_info(&pdev->dev, "no phyclk specified\n");
+		rphy->clk = NULL;
+	}
+
+	ret = rockchip_usb2phy_clk480m_register(rphy);
+	if (ret) {
+		dev_err(dev, "failed to register 480m output clock\n");
+		goto disable_clks;
+	}
+
+	index = 0;
+	for_each_available_child_of_node(np, child_np) {
+		struct rockchip_usb2phy_port *rport = &rphy->ports[index];
+		struct phy *phy;
+
+		/*
+		 * This driver aim to support both otg-port and host-port,
+		 * but unfortunately, the otg part is not ready in current,
+		 * so this comments and below codes are interim, which should
+		 * be changed after otg-port is supplied soon.
+		 */
+		if (of_node_cmp(child_np->name, "host-port"))
+			goto next_child;
+
+		phy = devm_phy_create(dev, child_np, &rockchip_usb2phy_ops);
+		if (IS_ERR(phy)) {
+			dev_err(dev, "failed to create phy\n");
+			ret = PTR_ERR(phy);
+			goto put_child;
+		}
+
+		rport->phy = phy;
+		phy_set_drvdata(rport->phy, rport);
+
+		ret = rockchip_usb2phy_host_port_init(rphy, rport, child_np);
+		if (ret)
+			goto put_child;
+
+next_child:
+		/* to prevent out of boundary */
+		if (++index >= rphy->phy_cfg->num_ports)
+			break;
+	}
+
+	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	return PTR_ERR_OR_ZERO(provider);
+
+put_child:
+	of_node_put(child_np);
+disable_clks:
+	if (rphy->clk) {
+		clk_disable_unprepare(rphy->clk);
+		clk_put(rphy->clk);
+	}
+	return ret;
+}
+
+static const struct rockchip_usb2phy_cfg rk3366_phy_cfgs[] = {
+	{
+		.reg = 0x700,
+		.num_ports	= 2,
+		.clkout_ctl	= { 0x0724, 15, 15, 1, 0 },
+		.port_cfgs	= {
+			[USB2PHY_PORT_HOST] = {
+				.phy_sus	= { 0x0728, 15, 0, 0, 0x1d1 },
+				.ls_det_en	= { 0x0680, 4, 4, 0, 1 },
+				.ls_det_st	= { 0x0690, 4, 4, 0, 1 },
+				.ls_det_clr	= { 0x06a0, 4, 4, 0, 1 },
+				.utmi_ls	= { 0x049c, 14, 13, 0, 1 },
+				.utmi_hstdet	= { 0x049c, 12, 12, 0, 1 }
+			}
+		},
+	},
+	{ /* sentinel */ }
+};
+
+static const struct rockchip_usb2phy_cfg rk3399_phy_cfgs[] = {
+	{
+		.reg = 0xe450,
+		.num_ports	= 2,
+		.clkout_ctl	= { 0xe450, 4, 4, 1, 0 },
+		.port_cfgs	= {
+			[USB2PHY_PORT_HOST] = {
+				.phy_sus	= { 0xe458, 1, 0, 0x2, 0x1 },
+				.ls_det_en	= { 0xe3c0, 6, 6, 0, 1 },
+				.ls_det_st	= { 0xe3e0, 6, 6, 0, 1 },
+				.ls_det_clr	= { 0xe3d0, 6, 6, 0, 1 },
+				.utmi_ls	= { 0xe2ac, 22, 21, 0, 1 },
+				.utmi_hstdet	= { 0xe2ac, 23, 23, 0, 1 }
+			}
+		},
+	},
+	{
+		.reg = 0xe460,
+		.num_ports	= 2,
+		.clkout_ctl	= { 0xe460, 4, 4, 1, 0 },
+		.port_cfgs	= {
+			[USB2PHY_PORT_HOST] = {
+				.phy_sus	= { 0xe468, 1, 0, 0x2, 0x1 },
+				.ls_det_en	= { 0xe3c0, 11, 11, 0, 1 },
+				.ls_det_st	= { 0xe3e0, 11, 11, 0, 1 },
+				.ls_det_clr	= { 0xe3d0, 11, 11, 0, 1 },
+				.utmi_ls	= { 0xe2ac, 26, 25, 0, 1 },
+				.utmi_hstdet	= { 0xe2ac, 27, 27, 0, 1 }
+			}
+		},
+	},
+	{ /* sentinel */ }
+};
+
+static const struct of_device_id rockchip_usb2phy_dt_match[] = {
+	{ .compatible = "rockchip,rk3366-usb2phy", .data = &rk3366_phy_cfgs },
+	{ .compatible = "rockchip,rk3399-usb2phy", .data = &rk3399_phy_cfgs },
+	{}
+};
+MODULE_DEVICE_TABLE(of, rockchip_usb2phy_dt_match);
+
+static struct platform_driver rockchip_usb2phy_driver = {
+	.probe		= rockchip_usb2phy_probe,
+	.driver		= {
+		.name	= "rockchip-usb2phy",
+		.of_match_table = rockchip_usb2phy_dt_match,
+	},
+};
+module_platform_driver(rockchip_usb2phy_driver);
+
+MODULE_AUTHOR("Frank Wang <frank.wang@rock-chips.com>");
+MODULE_DESCRIPTION("Rockchip USB2.0 PHY driver");
+MODULE_LICENSE("GPL v2");

drivers/phy/phy-rockchip-pcie.c

+/*
+ * Rockchip PCIe PHY driver
+ *
+ * Copyright (C) 2016 Shawn Lin <shawn.lin@rock-chips.com>
+ * Copyright (C) 2016 ROCKCHIP, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+/*
+ * The higher 16-bit of this register is used for write protection
+ * only if BIT(x + 16) set to 1 the BIT(x) can be written.
+ */
+#define HIWORD_UPDATE(val, mask, shift) \
+		((val) << (shift) | (mask) << ((shift) + 16))
+
+#define PHY_MAX_LANE_NUM      4
+#define PHY_CFG_DATA_SHIFT    7
+#define PHY_CFG_ADDR_SHIFT    1
+#define PHY_CFG_DATA_MASK     0xf
+#define PHY_CFG_ADDR_MASK     0x3f
+#define PHY_CFG_RD_MASK       0x3ff
+#define PHY_CFG_WR_ENABLE     1
+#define PHY_CFG_WR_DISABLE    1
+#define PHY_CFG_WR_SHIFT      0
+#define PHY_CFG_WR_MASK       1
+#define PHY_CFG_PLL_LOCK      0x10
+#define PHY_CFG_CLK_TEST      0x10
+#define PHY_CFG_CLK_SCC       0x12
+#define PHY_CFG_SEPE_RATE     BIT(3)
+#define PHY_CFG_PLL_100M      BIT(3)
+#define PHY_PLL_LOCKED        BIT(9)
+#define PHY_PLL_OUTPUT        BIT(10)
+#define PHY_LANE_A_STATUS     0x30
+#define PHY_LANE_B_STATUS     0x31
+#define PHY_LANE_C_STATUS     0x32
+#define PHY_LANE_D_STATUS     0x33
+#define PHY_LANE_RX_DET_SHIFT 11
+#define PHY_LANE_RX_DET_TH    0x1
+#define PHY_LANE_IDLE_OFF     0x1
+#define PHY_LANE_IDLE_MASK    0x1
+#define PHY_LANE_IDLE_A_SHIFT 3
+#define PHY_LANE_IDLE_B_SHIFT 4
+#define PHY_LANE_IDLE_C_SHIFT 5
+#define PHY_LANE_IDLE_D_SHIFT 6
+
+struct rockchip_pcie_data {
+	unsigned int pcie_conf;
+	unsigned int pcie_status;
+	unsigned int pcie_laneoff;
+};
+
+struct rockchip_pcie_phy {
+	struct rockchip_pcie_data *phy_data;
+	struct regmap *reg_base;
+	struct reset_control *phy_rst;
+	struct clk *clk_pciephy_ref;
+};
+
+static inline void phy_wr_cfg(struct rockchip_pcie_phy *rk_phy,
+			      u32 addr, u32 data)
+{
+	regmap_write(rk_phy->reg_base, rk_phy->phy_data->pcie_conf,
+		     HIWORD_UPDATE(data,
+				   PHY_CFG_DATA_MASK,
+				   PHY_CFG_DATA_SHIFT) |
+		     HIWORD_UPDATE(addr,
+				   PHY_CFG_ADDR_MASK,
+				   PHY_CFG_ADDR_SHIFT));
+	udelay(1);
+	regmap_write(rk_phy->reg_base, rk_phy->phy_data->pcie_conf,
+		     HIWORD_UPDATE(PHY_CFG_WR_ENABLE,
+				   PHY_CFG_WR_MASK,
+				   PHY_CFG_WR_SHIFT));
+	udelay(1);
+	regmap_write(rk_phy->reg_base, rk_phy->phy_data->pcie_conf,
+		     HIWORD_UPDATE(PHY_CFG_WR_DISABLE,
+				   PHY_CFG_WR_MASK,
+				   PHY_CFG_WR_SHIFT));
+}
+
+static inline u32 phy_rd_cfg(struct rockchip_pcie_phy *rk_phy,
+			     u32 addr)
+{
+	u32 val;
+
+	regmap_write(rk_phy->reg_base, rk_phy->phy_data->pcie_conf,
+		     HIWORD_UPDATE(addr,
+				   PHY_CFG_RD_MASK,
+				   PHY_CFG_ADDR_SHIFT));
+	regmap_read(rk_phy->reg_base,
+		    rk_phy->phy_data->pcie_status,
+		    &val);
+	return val;
+}
+
+static int rockchip_pcie_phy_power_off(struct phy *phy)
+{
+	struct rockchip_pcie_phy *rk_phy = phy_get_drvdata(phy);
+	int err = 0;
+
+	err = reset_control_assert(rk_phy->phy_rst);
+	if (err) {
+		dev_err(&phy->dev, "assert phy_rst err %d\n", err);
+		return err;
+	}
+
+	return 0;
+}
+
+static int rockchip_pcie_phy_power_on(struct phy *phy)
+{
+	struct rockchip_pcie_phy *rk_phy = phy_get_drvdata(phy);
+	int err = 0;
+	u32 status;
+	unsigned long timeout;
+
+	err = reset_control_deassert(rk_phy->phy_rst);
+	if (err) {
+		dev_err(&phy->dev, "deassert phy_rst err %d\n", err);
+		return err;
+	}
+
+	regmap_write(rk_phy->reg_base, rk_phy->phy_data->pcie_conf,
+		     HIWORD_UPDATE(PHY_CFG_PLL_LOCK,
+				   PHY_CFG_ADDR_MASK,
+				   PHY_CFG_ADDR_SHIFT));
+
+	/*
+	 * No documented timeout value for phy operation below,
+	 * so we make it large enough here. And we use loop-break
+	 * method which should not be harmful.
+	 */
+	timeout = jiffies + msecs_to_jiffies(1000);
+
+	err = -EINVAL;
+	while (time_before(jiffies, timeout)) {
+		regmap_read(rk_phy->reg_base,
+			    rk_phy->phy_data->pcie_status,
+			    &status);
+		if (status & PHY_PLL_LOCKED) {
+			dev_dbg(&phy->dev, "pll locked!\n");
+			err = 0;
+			break;
+		}
+		msleep(20);
+	}
+
+	if (err) {
+		dev_err(&phy->dev, "pll lock timeout!\n");
+		goto err_pll_lock;
+	}
+
+	phy_wr_cfg(rk_phy, PHY_CFG_CLK_TEST, PHY_CFG_SEPE_RATE);
+	phy_wr_cfg(rk_phy, PHY_CFG_CLK_SCC, PHY_CFG_PLL_100M);
+
+	err = -ETIMEDOUT;
+	while (time_before(jiffies, timeout)) {
+		regmap_read(rk_phy->reg_base,
+			    rk_phy->phy_data->pcie_status,
+			    &status);
+		if (!(status & PHY_PLL_OUTPUT)) {
+			dev_dbg(&phy->dev, "pll output enable done!\n");
+			err = 0;
+			break;
+		}
+		msleep(20);
+	}
+
+	if (err) {
+		dev_err(&phy->dev, "pll output enable timeout!\n");
+		goto err_pll_lock;
+	}
+
+	regmap_write(rk_phy->reg_base, rk_phy->phy_data->pcie_conf,
+		     HIWORD_UPDATE(PHY_CFG_PLL_LOCK,
+				   PHY_CFG_ADDR_MASK,
+				   PHY_CFG_ADDR_SHIFT));
+	err = -EINVAL;
+	while (time_before(jiffies, timeout)) {
+		regmap_read(rk_phy->reg_base,
+			    rk_phy->phy_data->pcie_status,
+			    &status);
+		if (status & PHY_PLL_LOCKED) {
+			dev_dbg(&phy->dev, "pll relocked!\n");
+			err = 0;
+			break;
+		}
+		msleep(20);
+	}
+
+	if (err) {
+		dev_err(&phy->dev, "pll relock timeout!\n");
+		goto err_pll_lock;
+	}
+
+	return 0;
+
+err_pll_lock:
+	reset_control_assert(rk_phy->phy_rst);
+	return err;
+}
+
+static int rockchip_pcie_phy_init(struct phy *phy)
+{
+	struct rockchip_pcie_phy *rk_phy = phy_get_drvdata(phy);
+	int err = 0;
+
+	err = clk_prepare_enable(rk_phy->clk_pciephy_ref);
+	if (err) {
+		dev_err(&phy->dev, "Fail to enable pcie ref clock.\n");
+		goto err_refclk;
+	}
+
+	err = reset_control_assert(rk_phy->phy_rst);
+	if (err) {
+		dev_err(&phy->dev, "assert phy_rst err %d\n", err);
+		goto err_reset;
+	}
+
+	return err;
+
+err_reset:
+	clk_disable_unprepare(rk_phy->clk_pciephy_ref);
+err_refclk:
+	return err;
+}
+
+static int rockchip_pcie_phy_exit(struct phy *phy)
+{
+	struct rockchip_pcie_phy *rk_phy = phy_get_drvdata(phy);
+	int err = 0;
+
+	clk_disable_unprepare(rk_phy->clk_pciephy_ref);
+
+	err = reset_control_deassert(rk_phy->phy_rst);
+	if (err) {
+		dev_err(&phy->dev, "deassert phy_rst err %d\n", err);
+		goto err_reset;
+	}
+
+	return err;
+
+err_reset:
+	clk_prepare_enable(rk_phy->clk_pciephy_ref);
+	return err;
+}
+
+static const struct phy_ops ops = {
+	.init		= rockchip_pcie_phy_init,
+	.exit		= rockchip_pcie_phy_exit,
+	.power_on	= rockchip_pcie_phy_power_on,
+	.power_off	= rockchip_pcie_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static const struct rockchip_pcie_data rk3399_pcie_data = {
+	.pcie_conf = 0xe220,
+	.pcie_status = 0xe2a4,
+	.pcie_laneoff = 0xe214,
+};
+
+static const struct of_device_id rockchip_pcie_phy_dt_ids[] = {
+	{
+		.compatible = "rockchip,rk3399-pcie-phy",
+		.data = &rk3399_pcie_data,
+	},
+	{}
+};
+
+MODULE_DEVICE_TABLE(of, rockchip_pcie_phy_dt_ids);
+
+static int rockchip_pcie_phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct rockchip_pcie_phy *rk_phy;
+	struct phy *generic_phy;
+	struct phy_provider *phy_provider;
+	struct regmap *grf;
+	const struct of_device_id *of_id;
+
+	grf = syscon_node_to_regmap(dev->parent->of_node);
+	if (IS_ERR(grf)) {
+		dev_err(dev, "Cannot find GRF syscon\n");
+		return PTR_ERR(grf);
+	}
+
+	rk_phy = devm_kzalloc(dev, sizeof(*rk_phy), GFP_KERNEL);
+	if (!rk_phy)
+		return -ENOMEM;
+
+	of_id = of_match_device(rockchip_pcie_phy_dt_ids, &pdev->dev);
+	if (!of_id)
+		return -EINVAL;
+
+	rk_phy->phy_data = (struct rockchip_pcie_data *)of_id->data;
+	rk_phy->reg_base = grf;
+
+	rk_phy->phy_rst = devm_reset_control_get(dev, "phy");
+	if (IS_ERR(rk_phy->phy_rst)) {
+		if (PTR_ERR(rk_phy->phy_rst) != -EPROBE_DEFER)
+			dev_err(dev,
+				"missing phy property for reset controller\n");
+		return PTR_ERR(rk_phy->phy_rst);
+	}
+
+	rk_phy->clk_pciephy_ref = devm_clk_get(dev, "refclk");
+	if (IS_ERR(rk_phy->clk_pciephy_ref)) {
+		dev_err(dev, "refclk not found.\n");
+		return PTR_ERR(rk_phy->clk_pciephy_ref);
+	}
+
+	generic_phy = devm_phy_create(dev, dev->of_node, &ops);
+	if (IS_ERR(generic_phy)) {
+		dev_err(dev, "failed to create PHY\n");
+		return PTR_ERR(generic_phy);
+	}
+
+	phy_set_drvdata(generic_phy, rk_phy);
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static struct platform_driver rockchip_pcie_driver = {
+	.probe		= rockchip_pcie_phy_probe,
+	.driver		= {
+		.name	= "rockchip-pcie-phy",
+		.of_match_table = rockchip_pcie_phy_dt_ids,
+	},
+};
+
+module_platform_driver(rockchip_pcie_driver);
+
+MODULE_AUTHOR("Shawn Lin <shawn.lin@rock-chips.com>");
+MODULE_DESCRIPTION("Rockchip PCIe PHY driver");
+MODULE_LICENSE("GPL v2");

drivers/phy/phy-rockchip-typec.c

+/*
+ * Copyright (C) Fuzhou Rockchip Electronics Co.Ltd
+ * Author: Chris Zhong <zyw@rock-chips.com>
+ *         Kever Yang <kever.yang@rock-chips.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * The ROCKCHIP Type-C PHY has two PLL clocks. The first PLL clock
+ * is used for USB3, the second PLL clock is used for DP. This Type-C PHY has
+ * 3 working modes: USB3 only mode, DP only mode, and USB3+DP mode.
+ * At USB3 only mode, both PLL clocks need to be initialized, this allows the
+ * PHY to switch mode between USB3 and USB3+DP, without disconnecting the USB
+ * device.
+ * In The DP only mode, only the DP PLL needs to be powered on, and the 4 lanes
+ * are all used for DP.
+ *
+ * This driver gets extcon cable state and property, then decides which mode to
+ * select:
+ *
+ * 1. USB3 only mode:
+ *    EXTCON_USB or EXTCON_USB_HOST state is true, and
+ *    EXTCON_PROP_USB_SS property is true.
+ *    EXTCON_DISP_DP state is false.
+ *
+ * 2. DP only mode:
+ *    EXTCON_DISP_DP state is true, and
+ *    EXTCON_PROP_USB_SS property is false.
+ *    If EXTCON_USB_HOST state is true, it is DP + USB2 mode, since the USB2 phy
+ *    is a separate phy, so this case is still DP only mode.
+ *
+ * 3. USB3+DP mode:
+ *    EXTCON_USB_HOST and EXTCON_DISP_DP are both true, and
+ *    EXTCON_PROP_USB_SS property is true.
+ *
+ * This Type-C PHY driver supports normal and flip orientation. The orientation
+ * is reported by the EXTCON_PROP_USB_TYPEC_POLARITY property: true is flip
+ * orientation, false is normal orientation.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/delay.h>
+#include <linux/extcon.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#include <linux/mfd/syscon.h>
+#include <linux/phy/phy.h>
+
+#define CMN_SSM_BANDGAP			(0x21 << 2)
+#define CMN_SSM_BIAS			(0x22 << 2)
+#define CMN_PLLSM0_PLLEN		(0x29 << 2)
+#define CMN_PLLSM0_PLLPRE		(0x2a << 2)
+#define CMN_PLLSM0_PLLVREF		(0x2b << 2)
+#define CMN_PLLSM0_PLLLOCK		(0x2c << 2)
+#define CMN_PLLSM1_PLLEN		(0x31 << 2)
+#define CMN_PLLSM1_PLLPRE		(0x32 << 2)
+#define CMN_PLLSM1_PLLVREF		(0x33 << 2)
+#define CMN_PLLSM1_PLLLOCK		(0x34 << 2)
+#define CMN_PLLSM1_USER_DEF_CTRL	(0x37 << 2)
+#define CMN_ICAL_OVRD			(0xc1 << 2)
+#define CMN_PLL0_VCOCAL_OVRD		(0x83 << 2)
+#define CMN_PLL0_VCOCAL_INIT		(0x84 << 2)
+#define CMN_PLL0_VCOCAL_ITER		(0x85 << 2)
+#define CMN_PLL0_LOCK_REFCNT_START	(0x90 << 2)
+#define CMN_PLL0_LOCK_PLLCNT_START	(0x92 << 2)
+#define CMN_PLL0_LOCK_PLLCNT_THR	(0x93 << 2)
+#define CMN_PLL0_INTDIV			(0x94 << 2)
+#define CMN_PLL0_FRACDIV		(0x95 << 2)
+#define CMN_PLL0_HIGH_THR		(0x96 << 2)
+#define CMN_PLL0_DSM_DIAG		(0x97 << 2)
+#define CMN_PLL0_SS_CTRL1		(0x98 << 2)
+#define CMN_PLL0_SS_CTRL2		(0x99 << 2)
+#define CMN_PLL1_VCOCAL_START		(0xa1 << 2)
+#define CMN_PLL1_VCOCAL_OVRD		(0xa3 << 2)
+#define CMN_PLL1_VCOCAL_INIT		(0xa4 << 2)
+#define CMN_PLL1_VCOCAL_ITER		(0xa5 << 2)
+#define CMN_PLL1_LOCK_REFCNT_START	(0xb0 << 2)
+#define CMN_PLL1_LOCK_PLLCNT_START	(0xb2 << 2)
+#define CMN_PLL1_LOCK_PLLCNT_THR	(0xb3 << 2)
+#define CMN_PLL1_INTDIV			(0xb4 << 2)
+#define CMN_PLL1_FRACDIV		(0xb5 << 2)
+#define CMN_PLL1_HIGH_THR		(0xb6 << 2)
+#define CMN_PLL1_DSM_DIAG		(0xb7 << 2)
+#define CMN_PLL1_SS_CTRL1		(0xb8 << 2)
+#define CMN_PLL1_SS_CTRL2		(0xb9 << 2)
+#define CMN_RXCAL_OVRD			(0xd1 << 2)
+#define CMN_TXPUCAL_CTRL		(0xe0 << 2)
+#define CMN_TXPUCAL_OVRD		(0xe1 << 2)
+#define CMN_TXPDCAL_OVRD		(0xf1 << 2)
+#define CMN_DIAG_PLL0_FBH_OVRD		(0x1c0 << 2)
+#define CMN_DIAG_PLL0_FBL_OVRD		(0x1c1 << 2)
+#define CMN_DIAG_PLL0_OVRD		(0x1c2 << 2)
+#define CMN_DIAG_PLL0_V2I_TUNE		(0x1c5 << 2)
+#define CMN_DIAG_PLL0_CP_TUNE		(0x1c6 << 2)
+#define CMN_DIAG_PLL0_LF_PROG		(0x1c7 << 2)
+#define CMN_DIAG_PLL1_FBH_OVRD		(0x1d0 << 2)
+#define CMN_DIAG_PLL1_FBL_OVRD		(0x1d1 << 2)
+#define CMN_DIAG_PLL1_OVRD		(0x1d2 << 2)
+#define CMN_DIAG_PLL1_V2I_TUNE		(0x1d5 << 2)
+#define CMN_DIAG_PLL1_CP_TUNE		(0x1d6 << 2)
+#define CMN_DIAG_PLL1_LF_PROG		(0x1d7 << 2)
+#define CMN_DIAG_PLL1_PTATIS_TUNE1	(0x1d8 << 2)
+#define CMN_DIAG_PLL1_PTATIS_TUNE2	(0x1d9 << 2)
+#define CMN_DIAG_PLL1_INCLK_CTRL	(0x1da << 2)
+#define CMN_DIAG_HSCLK_SEL		(0x1e0 << 2)
+
+#define XCVR_PSM_RCTRL(n)		((0x4001 | ((n) << 9)) << 2)
+#define XCVR_PSM_CAL_TMR(n)		((0x4002 | ((n) << 9)) << 2)
+#define XCVR_PSM_A0IN_TMR(n)		((0x4003 | ((n) << 9)) << 2)
+#define TX_TXCC_CAL_SCLR_MULT(n)	((0x4047 | ((n) << 9)) << 2)
+#define TX_TXCC_CPOST_MULT_00(n)	((0x404c | ((n) << 9)) << 2)
+#define TX_TXCC_CPOST_MULT_01(n)	((0x404d | ((n) << 9)) << 2)
+#define TX_TXCC_CPOST_MULT_10(n)	((0x404e | ((n) << 9)) << 2)
+#define TX_TXCC_CPOST_MULT_11(n)	((0x404f | ((n) << 9)) << 2)
+#define TX_TXCC_MGNFS_MULT_000(n)	((0x4050 | ((n) << 9)) << 2)
+#define TX_TXCC_MGNFS_MULT_001(n)	((0x4051 | ((n) << 9)) << 2)
+#define TX_TXCC_MGNFS_MULT_010(n)	((0x4052 | ((n) << 9)) << 2)
+#define TX_TXCC_MGNFS_MULT_011(n)	((0x4053 | ((n) << 9)) << 2)
+#define TX_TXCC_MGNFS_MULT_100(n)	((0x4054 | ((n) << 9)) << 2)
+#define TX_TXCC_MGNFS_MULT_101(n)	((0x4055 | ((n) << 9)) << 2)
+#define TX_TXCC_MGNFS_MULT_110(n)	((0x4056 | ((n) << 9)) << 2)
+#define TX_TXCC_MGNFS_MULT_111(n)	((0x4057 | ((n) << 9)) << 2)
+#define XCVR_DIAG_PLLDRC_CTRL(n)	((0x40e0 | ((n) << 9)) << 2)
+#define XCVR_DIAG_BIDI_CTRL(n)		((0x40e8 | ((n) << 9)) << 2)
+#define XCVR_DIAG_LANE_FCM_EN_MGN(n)	((0x40f2 | ((n) << 9)) << 2)
+#define TX_PSC_A0(n)			((0x4100 | ((n) << 9)) << 2)
+#define TX_PSC_A1(n)			((0x4101 | ((n) << 9)) << 2)
+#define TX_PSC_A2(n)			((0x4102 | ((n) << 9)) << 2)
+#define TX_PSC_A3(n)			((0x4103 | ((n) << 9)) << 2)
+#define TX_RCVDET_CTRL(n)		((0x4120 | ((n) << 9)) << 2)
+#define TX_RCVDET_EN_TMR(n)		((0x4122 | ((n) << 9)) << 2)
+#define TX_RCVDET_ST_TMR(n)		((0x4123 | ((n) << 9)) << 2)
+#define TX_DIAG_TX_DRV(n)		((0x41e1 | ((n) << 9)) << 2)
+#define TX_DIAG_BGREF_PREDRV_DELAY	(0x41e7 << 2)
+#define TX_ANA_CTRL_REG_1		(0x5020 << 2)
+#define TX_ANA_CTRL_REG_2		(0x5021 << 2)
+#define TXDA_COEFF_CALC_CTRL		(0x5022 << 2)
+#define TX_DIG_CTRL_REG_2		(0x5024 << 2)
+#define TXDA_CYA_AUXDA_CYA		(0x5025 << 2)
+#define TX_ANA_CTRL_REG_3		(0x5026 << 2)
+#define TX_ANA_CTRL_REG_4		(0x5027 << 2)
+#define TX_ANA_CTRL_REG_5		(0x5029 << 2)
+
+#define RX_PSC_A0(n)			((0x8000 | ((n) << 9)) << 2)
+#define RX_PSC_A1(n)			((0x8001 | ((n) << 9)) << 2)
+#define RX_PSC_A2(n)			((0x8002 | ((n) << 9)) << 2)
+#define RX_PSC_A3(n)			((0x8003 | ((n) << 9)) << 2)
+#define RX_PSC_CAL(n)			((0x8006 | ((n) << 9)) << 2)
+#define RX_PSC_RDY(n)			((0x8007 | ((n) << 9)) << 2)
+#define RX_IQPI_ILL_CAL_OVRD		(0x8023 << 2)
+#define RX_EPI_ILL_CAL_OVRD		(0x8033 << 2)
+#define RX_SDCAL0_OVRD			(0x8041 << 2)
+#define RX_SDCAL1_OVRD			(0x8049 << 2)
+#define RX_SLC_INIT			(0x806d << 2)
+#define RX_SLC_RUN			(0x806e << 2)
+#define RX_CDRLF_CNFG2			(0x8081 << 2)
+#define RX_SIGDET_HL_FILT_TMR(n)	((0x8090 | ((n) << 9)) << 2)
+#define RX_SLC_IOP0_OVRD		(0x8101 << 2)
+#define RX_SLC_IOP1_OVRD		(0x8105 << 2)
+#define RX_SLC_QOP0_OVRD		(0x8109 << 2)
+#define RX_SLC_QOP1_OVRD		(0x810d << 2)
+#define RX_SLC_EOP0_OVRD		(0x8111 << 2)
+#define RX_SLC_EOP1_OVRD		(0x8115 << 2)
+#define RX_SLC_ION0_OVRD		(0x8119 << 2)
+#define RX_SLC_ION1_OVRD		(0x811d << 2)
+#define RX_SLC_QON0_OVRD		(0x8121 << 2)
+#define RX_SLC_QON1_OVRD		(0x8125 << 2)
+#define RX_SLC_EON0_OVRD		(0x8129 << 2)
+#define RX_SLC_EON1_OVRD		(0x812d << 2)
+#define RX_SLC_IEP0_OVRD		(0x8131 << 2)
+#define RX_SLC_IEP1_OVRD		(0x8135 << 2)
+#define RX_SLC_QEP0_OVRD		(0x8139 << 2)
+#define RX_SLC_QEP1_OVRD		(0x813d << 2)
+#define RX_SLC_EEP0_OVRD		(0x8141 << 2)
+#define RX_SLC_EEP1_OVRD		(0x8145 << 2)
+#define RX_SLC_IEN0_OVRD		(0x8149 << 2)
+#define RX_SLC_IEN1_OVRD		(0x814d << 2)
+#define RX_SLC_QEN0_OVRD		(0x8151 << 2)
+#define RX_SLC_QEN1_OVRD		(0x8155 << 2)
+#define RX_SLC_EEN0_OVRD		(0x8159 << 2)
+#define RX_SLC_EEN1_OVRD		(0x815d << 2)
+#define RX_REE_CTRL_DATA_MASK(n)	((0x81bb | ((n) << 9)) << 2)
+#define RX_DIAG_SIGDET_TUNE(n)		((0x81dc | ((n) << 9)) << 2)
+#define RX_DIAG_SC2C_DELAY		(0x81e1 << 2)
+
+#define PMA_LANE_CFG			(0xc000 << 2)
+#define PIPE_CMN_CTRL1			(0xc001 << 2)
+#define PIPE_CMN_CTRL2			(0xc002 << 2)
+#define PIPE_COM_LOCK_CFG1		(0xc003 << 2)
+#define PIPE_COM_LOCK_CFG2		(0xc004 << 2)
+#define PIPE_RCV_DET_INH		(0xc005 << 2)
+#define DP_MODE_CTL			(0xc008 << 2)
+#define DP_CLK_CTL			(0xc009 << 2)
+#define STS				(0xc00F << 2)
+#define PHY_ISO_CMN_CTRL		(0xc010 << 2)
+#define PHY_DP_TX_CTL			(0xc408 << 2)
+#define PMA_CMN_CTRL1			(0xc800 << 2)
+#define PHY_PMA_ISO_CMN_CTRL		(0xc810 << 2)
+#define PHY_ISOLATION_CTRL		(0xc81f << 2)
+#define PHY_PMA_ISO_XCVR_CTRL(n)	((0xcc11 | ((n) << 6)) << 2)
+#define PHY_PMA_ISO_LINK_MODE(n)	((0xcc12 | ((n) << 6)) << 2)
+#define PHY_PMA_ISO_PWRST_CTRL(n)	((0xcc13 | ((n) << 6)) << 2)
+#define PHY_PMA_ISO_TX_DATA_LO(n)	((0xcc14 | ((n) << 6)) << 2)
+#define PHY_PMA_ISO_TX_DATA_HI(n)	((0xcc15 | ((n) << 6)) << 2)
+#define PHY_PMA_ISO_RX_DATA_LO(n)	((0xcc16 | ((n) << 6)) << 2)
+#define PHY_PMA_ISO_RX_DATA_HI(n)	((0xcc17 | ((n) << 6)) << 2)
+#define TX_BIST_CTRL(n)			((0x4140 | ((n) << 9)) << 2)
+#define TX_BIST_UDDWR(n)		((0x4141 | ((n) << 9)) << 2)
+
+/*
+ * Selects which PLL clock will be driven on the analog high speed
+ * clock 0: PLL 0 div 1
+ * clock 1: PLL 1 div 2
+ */
+#define CLK_PLL_CONFIG			0X30
+#define CLK_PLL_MASK			0x33
+
+#define CMN_READY			BIT(0)
+
+#define DP_PLL_CLOCK_ENABLE		BIT(2)
+#define DP_PLL_ENABLE			BIT(0)
+#define DP_PLL_DATA_RATE_RBR		((2 << 12) | (4 << 8))
+#define DP_PLL_DATA_RATE_HBR		((2 << 12) | (4 << 8))
+#define DP_PLL_DATA_RATE_HBR2		((1 << 12) | (2 << 8))
+
+#define DP_MODE_A0			BIT(4)
+#define DP_MODE_A2			BIT(6)
+#define DP_MODE_ENTER_A0		0xc101
+#define DP_MODE_ENTER_A2		0xc104
+
+#define PHY_MODE_SET_TIMEOUT		100000
+
+#define PIN_ASSIGN_C_E			0x51d9
+#define PIN_ASSIGN_D_F			0x5100
+
+#define MODE_DISCONNECT			0
+#define MODE_UFP_USB			BIT(0)
+#define MODE_DFP_USB			BIT(1)
+#define MODE_DFP_DP			BIT(2)
+
+struct usb3phy_reg {
+	u32 offset;
+	u32 enable_bit;
+	u32 write_enable;
+};
+
+struct rockchip_usb3phy_port_cfg {
+	struct usb3phy_reg typec_conn_dir;
+	struct usb3phy_reg usb3tousb2_en;
+	struct usb3phy_reg external_psm;
+	struct usb3phy_reg pipe_status;
+};
+
+struct rockchip_typec_phy {
+	struct device *dev;
+	void __iomem *base;
+	struct extcon_dev *extcon;
+	struct regmap *grf_regs;
+	struct clk *clk_core;
+	struct clk *clk_ref;
+	struct reset_control *uphy_rst;
+	struct reset_control *pipe_rst;
+	struct reset_control *tcphy_rst;
+	struct rockchip_usb3phy_port_cfg port_cfgs;
+	/* mutex to protect access to individual PHYs */
+	struct mutex lock;
+
+	bool flip;
+	u8 mode;
+};
+
+struct phy_reg {
+	u16 value;
+	u32 addr;
+};
+
+struct phy_reg usb3_pll_cfg[] = {
+	{ 0xf0,		CMN_PLL0_VCOCAL_INIT },
+	{ 0x18,		CMN_PLL0_VCOCAL_ITER },
+	{ 0xd0,		CMN_PLL0_INTDIV },
+	{ 0x4a4a,	CMN_PLL0_FRACDIV },
+	{ 0x34,		CMN_PLL0_HIGH_THR },
+	{ 0x1ee,	CMN_PLL0_SS_CTRL1 },
+	{ 0x7f03,	CMN_PLL0_SS_CTRL2 },
+	{ 0x20,		CMN_PLL0_DSM_DIAG },
+	{ 0,		CMN_DIAG_PLL0_OVRD },
+	{ 0,		CMN_DIAG_PLL0_FBH_OVRD },
+	{ 0,		CMN_DIAG_PLL0_FBL_OVRD },
+	{ 0x7,		CMN_DIAG_PLL0_V2I_TUNE },
+	{ 0x45,		CMN_DIAG_PLL0_CP_TUNE },
+	{ 0x8,		CMN_DIAG_PLL0_LF_PROG },
+};
+
+struct phy_reg dp_pll_cfg[] = {
+	{ 0xf0,		CMN_PLL1_VCOCAL_INIT },
+	{ 0x18,		CMN_PLL1_VCOCAL_ITER },
+	{ 0x30b9,	CMN_PLL1_VCOCAL_START },
+	{ 0x21c,	CMN_PLL1_INTDIV },
+	{ 0,		CMN_PLL1_FRACDIV },
+	{ 0x5,		CMN_PLL1_HIGH_THR },
+	{ 0x35,		CMN_PLL1_SS_CTRL1 },
+	{ 0x7f1e,	CMN_PLL1_SS_CTRL2 },
+	{ 0x20,		CMN_PLL1_DSM_DIAG },
+	{ 0,		CMN_PLLSM1_USER_DEF_CTRL },
+	{ 0,		CMN_DIAG_PLL1_OVRD },
+	{ 0,		CMN_DIAG_PLL1_FBH_OVRD },
+	{ 0,		CMN_DIAG_PLL1_FBL_OVRD },
+	{ 0x6,		CMN_DIAG_PLL1_V2I_TUNE },
+	{ 0x45,		CMN_DIAG_PLL1_CP_TUNE },
+	{ 0x8,		CMN_DIAG_PLL1_LF_PROG },
+	{ 0x100,	CMN_DIAG_PLL1_PTATIS_TUNE1 },
+	{ 0x7,		CMN_DIAG_PLL1_PTATIS_TUNE2 },
+	{ 0x4,		CMN_DIAG_PLL1_INCLK_CTRL },
+};
+
+static void tcphy_cfg_24m(struct rockchip_typec_phy *tcphy)
+{
+	u32 i, rdata;
+
+	/*
+	 * cmn_ref_clk_sel = 3, select the 24Mhz for clk parent
+	 * cmn_psm_clk_dig_div = 2, set the clk division to 2
+	 */
+	writel(0x830, tcphy->base + PMA_CMN_CTRL1);
+	for (i = 0; i < 4; i++) {
+		/*
+		 * The following PHY configuration assumes a 24 MHz reference
+		 * clock.
+		 */
+		writel(0x90, tcphy->base + XCVR_DIAG_LANE_FCM_EN_MGN(i));
+		writel(0x960, tcphy->base + TX_RCVDET_EN_TMR(i));
+		writel(0x30, tcphy->base + TX_RCVDET_ST_TMR(i));
+	}
+
+	rdata = readl(tcphy->base + CMN_DIAG_HSCLK_SEL);
+	rdata &= ~CLK_PLL_MASK;
+	rdata |= CLK_PLL_CONFIG;
+	writel(rdata, tcphy->base + CMN_DIAG_HSCLK_SEL);
+}
+
+static void tcphy_cfg_usb3_pll(struct rockchip_typec_phy *tcphy)
+{
+	u32 i;
+
+	/* load the configuration of PLL0 */
+	for (i = 0; i < ARRAY_SIZE(usb3_pll_cfg); i++)
+		writel(usb3_pll_cfg[i].value,
+		       tcphy->base + usb3_pll_cfg[i].addr);
+}
+
+static void tcphy_cfg_dp_pll(struct rockchip_typec_phy *tcphy)
+{
+	u32 i;
+
+	/* set the default mode to RBR */
+	writel(DP_PLL_CLOCK_ENABLE | DP_PLL_ENABLE | DP_PLL_DATA_RATE_RBR,
+	       tcphy->base + DP_CLK_CTL);
+
+	/* load the configuration of PLL1 */
+	for (i = 0; i < ARRAY_SIZE(dp_pll_cfg); i++)
+		writel(dp_pll_cfg[i].value, tcphy->base + dp_pll_cfg[i].addr);
+}
+
+static void tcphy_tx_usb3_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane)
+{
+	writel(0x7799, tcphy->base + TX_PSC_A0(lane));
+	writel(0x7798, tcphy->base + TX_PSC_A1(lane));
+	writel(0x5098, tcphy->base + TX_PSC_A2(lane));
+	writel(0x5098, tcphy->base + TX_PSC_A3(lane));
+	writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_000(lane));
+	writel(0xbf, tcphy->base + XCVR_DIAG_BIDI_CTRL(lane));
+}
+
+static void tcphy_rx_usb3_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane)
+{
+	writel(0xa6fd, tcphy->base + RX_PSC_A0(lane));
+	writel(0xa6fd, tcphy->base + RX_PSC_A1(lane));
+	writel(0xa410, tcphy->base + RX_PSC_A2(lane));
+	writel(0x2410, tcphy->base + RX_PSC_A3(lane));
+	writel(0x23ff, tcphy->base + RX_PSC_CAL(lane));
+	writel(0x13, tcphy->base + RX_SIGDET_HL_FILT_TMR(lane));
+	writel(0x03e7, tcphy->base + RX_REE_CTRL_DATA_MASK(lane));
+	writel(0x1004, tcphy->base + RX_DIAG_SIGDET_TUNE(lane));
+	writel(0x2010, tcphy->base + RX_PSC_RDY(lane));
+	writel(0xfb, tcphy->base + XCVR_DIAG_BIDI_CTRL(lane));
+}
+
+static void tcphy_dp_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane)
+{
+	u16 rdata;
+
+	writel(0xbefc, tcphy->base + XCVR_PSM_RCTRL(lane));
+	writel(0x6799, tcphy->base + TX_PSC_A0(lane));
+	writel(0x6798, tcphy->base + TX_PSC_A1(lane));
+	writel(0x98, tcphy->base + TX_PSC_A2(lane));
+	writel(0x98, tcphy->base + TX_PSC_A3(lane));
+
+	writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_000(lane));
+	writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_001(lane));
+	writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_010(lane));
+	writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_011(lane));
+	writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_100(lane));
+	writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_101(lane));
+	writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_110(lane));
+	writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_111(lane));
+	writel(0, tcphy->base + TX_TXCC_CPOST_MULT_10(lane));
+	writel(0, tcphy->base + TX_TXCC_CPOST_MULT_01(lane));
+	writel(0, tcphy->base + TX_TXCC_CPOST_MULT_00(lane));
+	writel(0, tcphy->base + TX_TXCC_CPOST_MULT_11(lane));
+
+	writel(0x128, tcphy->base + TX_TXCC_CAL_SCLR_MULT(lane));
+	writel(0x400, tcphy->base + TX_DIAG_TX_DRV(lane));
+
+	rdata = readl(tcphy->base + XCVR_DIAG_PLLDRC_CTRL(lane));
+	rdata = (rdata & 0x8fff) | 0x6000;
+	writel(rdata, tcphy->base + XCVR_DIAG_PLLDRC_CTRL(lane));
+}
+
+static inline int property_enable(struct rockchip_typec_phy *tcphy,
+				  const struct usb3phy_reg *reg, bool en)
+{
+	u32 mask = 1 << reg->write_enable;
+	u32 val = en << reg->enable_bit;
+
+	return regmap_write(tcphy->grf_regs, reg->offset, val | mask);
+}
+
+static void tcphy_dp_aux_calibration(struct rockchip_typec_phy *tcphy)
+{
+	u16 rdata, rdata2, val;
+
+	/* disable txda_cal_latch_en for rewrite the calibration values */
+	rdata = readl(tcphy->base + TX_ANA_CTRL_REG_1);
+	val = rdata & 0xdfff;
+	writel(val, tcphy->base + TX_ANA_CTRL_REG_1);
+
+	/*
+	 * read a resistor calibration code from CMN_TXPUCAL_CTRL[6:0] and
+	 * write it to TX_DIG_CTRL_REG_2[6:0], and delay 1ms to make sure it
+	 * works.
+	 */
+	rdata = readl(tcphy->base + TX_DIG_CTRL_REG_2);
+	rdata = rdata & 0xffc0;
+
+	rdata2 = readl(tcphy->base + CMN_TXPUCAL_CTRL);
+	rdata2 = rdata2 & 0x3f;
+
+	val = rdata | rdata2;
+	writel(val, tcphy->base + TX_DIG_CTRL_REG_2);
+	usleep_range(1000, 1050);
+
+	/*
+	 * Enable signal for latch that sample and holds calibration values.
+	 * Activate this signal for 1 clock cycle to sample new calibration
+	 * values.
+	 */
+	rdata = readl(tcphy->base + TX_ANA_CTRL_REG_1);
+	val = rdata | 0x2000;
+	writel(val, tcphy->base + TX_ANA_CTRL_REG_1);
+	usleep_range(150, 200);
+
+	/* set TX Voltage Level and TX Deemphasis to 0 */
+	writel(0, tcphy->base + PHY_DP_TX_CTL);
+	/* re-enable decap */
+	writel(0x100, tcphy->base + TX_ANA_CTRL_REG_2);
+	writel(0x300, tcphy->base + TX_ANA_CTRL_REG_2);
+	writel(0x2008, tcphy->base + TX_ANA_CTRL_REG_1);
+	writel(0x2018, tcphy->base + TX_ANA_CTRL_REG_1);
+
+	writel(0, tcphy->base + TX_ANA_CTRL_REG_5);
+
+	/*
+	 * Programs txda_drv_ldo_prog[15:0], Sets driver LDO
+	 * voltage 16'h1001 for DP-AUX-TX and RX
+	 */
+	writel(0x1001, tcphy->base + TX_ANA_CTRL_REG_4);
+
+	/* re-enables Bandgap reference for LDO */
+	writel(0x2098, tcphy->base + TX_ANA_CTRL_REG_1);
+	writel(0x2198, tcphy->base + TX_ANA_CTRL_REG_1);
+
+	/*
+	 * re-enables the transmitter pre-driver, driver data selection MUX,
+	 * and receiver detect circuits.
+	 */
+	writel(0x301, tcphy->base + TX_ANA_CTRL_REG_2);
+	writel(0x303, tcphy->base + TX_ANA_CTRL_REG_2);
+
+	/*
+	 * BIT 12: Controls auxda_polarity, which selects the polarity of the
+	 * xcvr:
+	 * 1, Reverses the polarity (If TYPEC, Pulls ups aux_p and pull
+	 * down aux_m)
+	 * 0, Normal polarity (if TYPE_C, pulls up aux_m and pulls down
+	 * aux_p)
+	 */
+	val = 0xa078;
+	if (!tcphy->flip)
+		val |= BIT(12);
+	writel(val, tcphy->base + TX_ANA_CTRL_REG_1);
+
+	writel(0, tcphy->base + TX_ANA_CTRL_REG_3);
+	writel(0, tcphy->base + TX_ANA_CTRL_REG_4);
+	writel(0, tcphy->base + TX_ANA_CTRL_REG_5);
+
+	/*
+	 * Controls low_power_swing_en, set the voltage swing of the driver
+	 * to 400mv. The values	below are peak to peak (differential) values.
+	 */
+	writel(4, tcphy->base + TXDA_COEFF_CALC_CTRL);
+	writel(0, tcphy->base + TXDA_CYA_AUXDA_CYA);
+
+	/* Controls tx_high_z_tm_en */
+	val = readl(tcphy->base + TX_DIG_CTRL_REG_2);
+	val |= BIT(15);
+	writel(val, tcphy->base + TX_DIG_CTRL_REG_2);
+}
+
+static int tcphy_phy_init(struct rockchip_typec_phy *tcphy, u8 mode)
+{
+	struct rockchip_usb3phy_port_cfg *cfg = &tcphy->port_cfgs;
+	int ret, i;
+	u32 val;
+
+	ret = clk_prepare_enable(tcphy->clk_core);
+	if (ret) {
+		dev_err(tcphy->dev, "Failed to prepare_enable core clock\n");
+		return ret;
+	}
+
+	ret = clk_prepare_enable(tcphy->clk_ref);
+	if (ret) {
+		dev_err(tcphy->dev, "Failed to prepare_enable ref clock\n");
+		goto err_clk_core;
+	}
+
+	reset_control_deassert(tcphy->tcphy_rst);
+
+	property_enable(tcphy, &cfg->typec_conn_dir, tcphy->flip);
+
+	tcphy_cfg_24m(tcphy);
+
+	if (mode == MODE_DFP_DP) {
+		tcphy_cfg_dp_pll(tcphy);
+		for (i = 0; i < 4; i++)
+			tcphy_dp_cfg_lane(tcphy, i);
+
+		writel(PIN_ASSIGN_C_E, tcphy->base + PMA_LANE_CFG);
+	} else {
+		tcphy_cfg_usb3_pll(tcphy);
+		tcphy_cfg_dp_pll(tcphy);
+		if (tcphy->flip) {
+			tcphy_tx_usb3_cfg_lane(tcphy, 3);
+			tcphy_rx_usb3_cfg_lane(tcphy, 2);
+			tcphy_dp_cfg_lane(tcphy, 0);
+			tcphy_dp_cfg_lane(tcphy, 1);
+		} else {
+			tcphy_tx_usb3_cfg_lane(tcphy, 0);
+			tcphy_rx_usb3_cfg_lane(tcphy, 1);
+			tcphy_dp_cfg_lane(tcphy, 2);
+			tcphy_dp_cfg_lane(tcphy, 3);
+		}
+
+		writel(PIN_ASSIGN_D_F, tcphy->base + PMA_LANE_CFG);
+	}
+
+	writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL);
+
+	reset_control_deassert(tcphy->uphy_rst);
+
+	ret = readx_poll_timeout(readl, tcphy->base + PMA_CMN_CTRL1,
+				 val, val & CMN_READY, 10,
+				 PHY_MODE_SET_TIMEOUT);
+	if (ret < 0) {
+		dev_err(tcphy->dev, "wait pma ready timeout\n");
+		ret = -ETIMEDOUT;
+		goto err_wait_pma;
+	}
+
+	reset_control_deassert(tcphy->pipe_rst);
+
+	return 0;
+
+err_wait_pma:
+	reset_control_assert(tcphy->uphy_rst);
+	reset_control_assert(tcphy->tcphy_rst);
+	clk_disable_unprepare(tcphy->clk_ref);
+err_clk_core:
+	clk_disable_unprepare(tcphy->clk_core);
+	return ret;
+}
+
+static void tcphy_phy_deinit(struct rockchip_typec_phy *tcphy)
+{
+	reset_control_assert(tcphy->tcphy_rst);
+	reset_control_assert(tcphy->uphy_rst);
+	reset_control_assert(tcphy->pipe_rst);
+	clk_disable_unprepare(tcphy->clk_core);
+	clk_disable_unprepare(tcphy->clk_ref);
+}
+
+static int tcphy_get_mode(struct rockchip_typec_phy *tcphy)
+{
+	struct extcon_dev *edev = tcphy->extcon;
+	union extcon_property_value property;
+	unsigned int id;
+	bool dfp, ufp, dp;
+	u8 mode;
+	int ret;
+
+	ufp = extcon_get_state(edev, EXTCON_USB);
+	dfp = extcon_get_state(edev, EXTCON_USB_HOST);
+	dp = extcon_get_state(edev, EXTCON_DISP_DP);
+
+	mode = MODE_DFP_USB;
+	id = EXTCON_USB_HOST;
+
+	if (ufp) {
+		mode = MODE_UFP_USB;
+		id = EXTCON_USB;
+	} else if (dp) {
+		mode = MODE_DFP_DP;
+		id = EXTCON_DISP_DP;
+
+		ret = extcon_get_property(edev, id, EXTCON_PROP_USB_SS,
+					  &property);
+		if (ret) {
+			dev_err(tcphy->dev, "get superspeed property failed\n");
+			return ret;
+		}
+
+		if (property.intval)
+			mode |= MODE_DFP_USB;
+	}
+
+	ret = extcon_get_property(edev, id, EXTCON_PROP_USB_TYPEC_POLARITY,
+				  &property);
+	if (ret) {
+		dev_err(tcphy->dev, "get polarity property failed\n");
+		return ret;
+	}
+
+	tcphy->flip = property.intval ? 1 : 0;
+
+	return mode;
+}
+
+static int rockchip_usb3_phy_power_on(struct phy *phy)
+{
+	struct rockchip_typec_phy *tcphy = phy_get_drvdata(phy);
+	struct rockchip_usb3phy_port_cfg *cfg = &tcphy->port_cfgs;
+	const struct usb3phy_reg *reg = &cfg->pipe_status;
+	int timeout, new_mode, ret = 0;
+	u32 val;
+
+	mutex_lock(&tcphy->lock);
+
+	new_mode = tcphy_get_mode(tcphy);
+	if (new_mode < 0) {
+		ret = new_mode;
+		goto unlock_ret;
+	}
+
+	/* DP-only mode; fall back to USB2 */
+	if (!(new_mode & (MODE_DFP_USB | MODE_UFP_USB)))
+		goto unlock_ret;
+
+	if (tcphy->mode == new_mode)
+		goto unlock_ret;
+
+	if (tcphy->mode == MODE_DISCONNECT)
+		tcphy_phy_init(tcphy, new_mode);
+
+	/* wait TCPHY for pipe ready */
+	for (timeout = 0; timeout < 100; timeout++) {
+		regmap_read(tcphy->grf_regs, reg->offset, &val);
+		if (!(val & BIT(reg->enable_bit))) {
+			tcphy->mode |= new_mode & (MODE_DFP_USB | MODE_UFP_USB);
+			goto unlock_ret;
+		}
+		usleep_range(10, 20);
+	}
+
+	if (tcphy->mode == MODE_DISCONNECT)
+		tcphy_phy_deinit(tcphy);
+
+	ret = -ETIMEDOUT;
+
+unlock_ret:
+	mutex_unlock(&tcphy->lock);
+	return ret;
+}
+
+static int rockchip_usb3_phy_power_off(struct phy *phy)
+{
+	struct rockchip_typec_phy *tcphy = phy_get_drvdata(phy);
+
+	mutex_lock(&tcphy->lock);
+
+	if (tcphy->mode == MODE_DISCONNECT)
+		goto unlock;
+
+	tcphy->mode &= ~(MODE_UFP_USB | MODE_DFP_USB);
+	if (tcphy->mode == MODE_DISCONNECT)
+		tcphy_phy_deinit(tcphy);
+
+unlock:
+	mutex_unlock(&tcphy->lock);
+	return 0;
+}
+
+static const struct phy_ops rockchip_usb3_phy_ops = {
+	.power_on	= rockchip_usb3_phy_power_on,
+	.power_off	= rockchip_usb3_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static int rockchip_dp_phy_power_on(struct phy *phy)
+{
+	struct rockchip_typec_phy *tcphy = phy_get_drvdata(phy);
+	int new_mode, ret = 0;
+	u32 val;
+
+	mutex_lock(&tcphy->lock);
+
+	new_mode = tcphy_get_mode(tcphy);
+	if (new_mode < 0) {
+		ret = new_mode;
+		goto unlock_ret;
+	}
+
+	if (!(new_mode & MODE_DFP_DP)) {
+		ret = -ENODEV;
+		goto unlock_ret;
+	}
+
+	if (tcphy->mode == new_mode)
+		goto unlock_ret;
+
+	/*
+	 * If the PHY has been power on, but the mode is not DP only mode,
+	 * re-init the PHY for setting all of 4 lanes to DP.
+	 */
+	if (new_mode == MODE_DFP_DP && tcphy->mode != MODE_DISCONNECT) {
+		tcphy_phy_deinit(tcphy);
+		tcphy_phy_init(tcphy, new_mode);
+	} else if (tcphy->mode == MODE_DISCONNECT) {
+		tcphy_phy_init(tcphy, new_mode);
+	}
+
+	ret = readx_poll_timeout(readl, tcphy->base + DP_MODE_CTL,
+				 val, val & DP_MODE_A2, 1000,
+				 PHY_MODE_SET_TIMEOUT);
+	if (ret < 0) {
+		dev_err(tcphy->dev, "failed to wait TCPHY enter A2\n");
+		goto power_on_finish;
+	}
+
+	tcphy_dp_aux_calibration(tcphy);
+
+	writel(DP_MODE_ENTER_A0, tcphy->base + DP_MODE_CTL);
+
+	ret = readx_poll_timeout(readl, tcphy->base + DP_MODE_CTL,
+				 val, val & DP_MODE_A0, 1000,
+				 PHY_MODE_SET_TIMEOUT);
+	if (ret < 0) {
+		writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL);
+		dev_err(tcphy->dev, "failed to wait TCPHY enter A0\n");
+		goto power_on_finish;
+	}
+
+	tcphy->mode |= MODE_DFP_DP;
+
+power_on_finish:
+	if (tcphy->mode == MODE_DISCONNECT)
+		tcphy_phy_deinit(tcphy);
+unlock_ret:
+	mutex_unlock(&tcphy->lock);
+	return ret;
+}
+
+static int rockchip_dp_phy_power_off(struct phy *phy)
+{
+	struct rockchip_typec_phy *tcphy = phy_get_drvdata(phy);
+
+	mutex_lock(&tcphy->lock);
+
+	if (tcphy->mode == MODE_DISCONNECT)
+		goto unlock;
+
+	tcphy->mode &= ~MODE_DFP_DP;
+
+	writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL);
+
+	if (tcphy->mode == MODE_DISCONNECT)
+		tcphy_phy_deinit(tcphy);
+
+unlock:
+	mutex_unlock(&tcphy->lock);
+	return 0;
+}
+
+static const struct phy_ops rockchip_dp_phy_ops = {
+	.power_on	= rockchip_dp_phy_power_on,
+	.power_off	= rockchip_dp_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static int tcphy_get_param(struct device *dev,
+			   struct usb3phy_reg *reg,
+			   const char *name)
+{
+	u32 buffer[3];
+	int ret;
+
+	ret = of_property_read_u32_array(dev->of_node, name, buffer, 3);
+	if (ret) {
+		dev_err(dev, "Can not parse %s\n", name);
+		return ret;
+	}
+
+	reg->offset = buffer[0];
+	reg->enable_bit = buffer[1];
+	reg->write_enable = buffer[2];
+	return 0;
+}
+
+static int tcphy_parse_dt(struct rockchip_typec_phy *tcphy,
+			  struct device *dev)
+{
+	struct rockchip_usb3phy_port_cfg *cfg = &tcphy->port_cfgs;
+	int ret;
+
+	ret = tcphy_get_param(dev, &cfg->typec_conn_dir,
+			      "rockchip,typec-conn-dir");
+	if (ret)
+		return ret;
+
+	ret = tcphy_get_param(dev, &cfg->usb3tousb2_en,
+			      "rockchip,usb3tousb2-en");
+	if (ret)
+		return ret;
+
+	ret = tcphy_get_param(dev, &cfg->external_psm,
+			      "rockchip,external-psm");
+	if (ret)
+		return ret;
+
+	ret = tcphy_get_param(dev, &cfg->pipe_status,
+			      "rockchip,pipe-status");
+	if (ret)
+		return ret;
+
+	tcphy->grf_regs = syscon_regmap_lookup_by_phandle(dev->of_node,
+							  "rockchip,grf");
+	if (IS_ERR(tcphy->grf_regs)) {
+		dev_err(dev, "could not find grf dt node\n");
+		return PTR_ERR(tcphy->grf_regs);
+	}
+
+	tcphy->clk_core = devm_clk_get(dev, "tcpdcore");
+	if (IS_ERR(tcphy->clk_core)) {
+		dev_err(dev, "could not get uphy core clock\n");
+		return PTR_ERR(tcphy->clk_core);
+	}
+
+	tcphy->clk_ref = devm_clk_get(dev, "tcpdphy-ref");
+	if (IS_ERR(tcphy->clk_ref)) {
+		dev_err(dev, "could not get uphy ref clock\n");
+		return PTR_ERR(tcphy->clk_ref);
+	}
+
+	tcphy->uphy_rst = devm_reset_control_get(dev, "uphy");
+	if (IS_ERR(tcphy->uphy_rst)) {
+		dev_err(dev, "no uphy_rst reset control found\n");
+		return PTR_ERR(tcphy->uphy_rst);
+	}
+
+	tcphy->pipe_rst = devm_reset_control_get(dev, "uphy-pipe");
+	if (IS_ERR(tcphy->pipe_rst)) {
+		dev_err(dev, "no pipe_rst reset control found\n");
+		return PTR_ERR(tcphy->pipe_rst);
+	}
+
+	tcphy->tcphy_rst = devm_reset_control_get(dev, "uphy-tcphy");
+	if (IS_ERR(tcphy->tcphy_rst)) {
+		dev_err(dev, "no tcphy_rst reset control found\n");
+		return PTR_ERR(tcphy->tcphy_rst);
+	}
+
+	return 0;
+}
+
+static void typec_phy_pre_init(struct rockchip_typec_phy *tcphy)
+{
+	struct rockchip_usb3phy_port_cfg *cfg = &tcphy->port_cfgs;
+
+	reset_control_assert(tcphy->tcphy_rst);
+	reset_control_assert(tcphy->uphy_rst);
+	reset_control_assert(tcphy->pipe_rst);
+
+	/* select external psm clock */
+	property_enable(tcphy, &cfg->external_psm, 1);
+	property_enable(tcphy, &cfg->usb3tousb2_en, 0);
+
+	tcphy->mode = MODE_DISCONNECT;
+}
+
+static int rockchip_typec_phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct device_node *child_np;
+	struct rockchip_typec_phy *tcphy;
+	struct phy_provider *phy_provider;
+	struct resource *res;
+	int ret;
+
+	tcphy = devm_kzalloc(dev, sizeof(*tcphy), GFP_KERNEL);
+	if (!tcphy)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	tcphy->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(tcphy->base))
+		return PTR_ERR(tcphy->base);
+
+	ret = tcphy_parse_dt(tcphy, dev);
+	if (ret)
+		return ret;
+
+	tcphy->dev = dev;
+	platform_set_drvdata(pdev, tcphy);
+	mutex_init(&tcphy->lock);
+
+	typec_phy_pre_init(tcphy);
+
+	tcphy->extcon = extcon_get_edev_by_phandle(dev, 0);
+	if (IS_ERR(tcphy->extcon)) {
+		if (PTR_ERR(tcphy->extcon) != -EPROBE_DEFER)
+			dev_err(dev, "Invalid or missing extcon\n");
+		return PTR_ERR(tcphy->extcon);
+	}
+
+	pm_runtime_enable(dev);
+
+	for_each_available_child_of_node(np, child_np) {
+		struct phy *phy;
+
+		if (!of_node_cmp(child_np->name, "dp-port"))
+			phy = devm_phy_create(dev, child_np,
+					      &rockchip_dp_phy_ops);
+		else if (!of_node_cmp(child_np->name, "usb3-port"))
+			phy = devm_phy_create(dev, child_np,
+					      &rockchip_usb3_phy_ops);
+		else
+			continue;
+
+		if (IS_ERR(phy)) {
+			dev_err(dev, "failed to create phy: %s\n",
+				child_np->name);
+			return PTR_ERR(phy);
+		}
+
+		phy_set_drvdata(phy, tcphy);
+	}
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (IS_ERR(phy_provider)) {
+		dev_err(dev, "Failed to register phy provider\n");
+		return PTR_ERR(phy_provider);
+	}
+
+	return 0;
+}
+
+static int rockchip_typec_phy_remove(struct platform_device *pdev)
+{
+	pm_runtime_disable(&pdev->dev);
+
+	return 0;
+}
+
+static const struct of_device_id rockchip_typec_phy_dt_ids[] = {
+	{ .compatible = "rockchip,rk3399-typec-phy" },
+	{}
+};
+
+MODULE_DEVICE_TABLE(of, rockchip_typec_phy_dt_ids);
+
+static struct platform_driver rockchip_typec_phy_driver = {
+	.probe		= rockchip_typec_phy_probe,
+	.remove		= rockchip_typec_phy_remove,
+	.driver		= {
+		.name	= "rockchip-typec-phy",
+		.of_match_table = rockchip_typec_phy_dt_ids,
+	},
+};
+
+module_platform_driver(rockchip_typec_phy_driver);
+
+MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>");
+MODULE_AUTHOR("Kever Yang <kever.yang@rock-chips.com>");
+MODULE_DESCRIPTION("Rockchip USB TYPE-C PHY driver");
+MODULE_LICENSE("GPL v2");

drivers/phy/phy-rockchip-usb.c

@@ -29,6 +29,7 @@
 #include <linux/reset.h>
 #include <linux/regmap.h>
 #include <linux/mfd/syscon.h>
+#include <linux/delay.h>
 
 static int enable_usb_uart;
 
@@ -64,6 +65,7 @@ struct rockchip_usb_phy {
 	struct clk_hw	clk480m_hw;
 	struct phy	*phy;
 	bool		uart_enabled;
+	struct reset_control *reset;
 };
 
 static int rockchip_usb_phy_power(struct rockchip_usb_phy *phy,
@@ -144,9 +146,23 @@ static int rockchip_usb_phy_power_on(struct phy *_phy)
 	return clk_prepare_enable(phy->clk480m);
 }
 
+static int rockchip_usb_phy_reset(struct phy *_phy)
+{
+	struct rockchip_usb_phy *phy = phy_get_drvdata(_phy);
+
+	if (phy->reset) {
+		reset_control_assert(phy->reset);
+		udelay(10);
+		reset_control_deassert(phy->reset);
+	}
+
+	return 0;
+}
+
 static const struct phy_ops ops = {
 	.power_on	= rockchip_usb_phy_power_on,
 	.power_off	= rockchip_usb_phy_power_off,
+	.reset		= rockchip_usb_phy_reset,
 	.owner		= THIS_MODULE,
 };
 
@@ -185,6 +201,10 @@ static int rockchip_usb_phy_init(struct rockchip_usb_phy_base *base,
 		return -EINVAL;
 	}
 
+	rk_phy->reset = of_reset_control_get(child, "phy-reset");
+	if (IS_ERR(rk_phy->reset))
+		rk_phy->reset = NULL;
+
 	rk_phy->reg_offset = reg_offset;
 
 	rk_phy->clk = of_clk_get_by_name(child, "phyclk");

drivers/phy/phy-sun4i-usb.c

@@ -40,6 +40,7 @@
 #include <linux/power_supply.h>
 #include <linux/regulator/consumer.h>
 #include <linux/reset.h>
+#include <linux/spinlock.h>
 #include <linux/usb/of.h>
 #include <linux/workqueue.h>
 
@@ -50,7 +51,7 @@
 #define REG_PHYCTL_A33			0x10
 #define REG_PHY_UNK_H3			0x20
 
-#define REG_PMU_UNK_H3			0x10
+#define REG_PMU_UNK1			0x10
 
 #define PHYCTL_DATA			BIT(7)
 
@@ -98,6 +99,7 @@ enum sun4i_usb_phy_type {
 	sun6i_a31_phy,
 	sun8i_a33_phy,
 	sun8i_h3_phy,
+	sun50i_a64_phy,
 };
 
 struct sun4i_usb_phy_cfg {
@@ -106,13 +108,14 @@ struct sun4i_usb_phy_cfg {
 	u32 disc_thresh;
 	u8 phyctl_offset;
 	bool dedicated_clocks;
+	bool enable_pmu_unk1;
 };
 
 struct sun4i_usb_phy_data {
 	void __iomem *base;
 	const struct sun4i_usb_phy_cfg *cfg;
 	enum usb_dr_mode dr_mode;
-	struct mutex mutex;
+	spinlock_t reg_lock; /* guard access to phyctl reg */
 	struct sun4i_usb_phy {
 		struct phy *phy;
 		void __iomem *pmu;
@@ -122,7 +125,6 @@ struct sun4i_usb_phy_data {
 		bool regulator_on;
 		int index;
 	} phys[MAX_PHYS];
-	int first_phy;
 	/* phy0 / otg related variables */
 	struct extcon_dev *extcon;
 	bool phy0_init;
@@ -131,6 +133,7 @@ struct sun4i_usb_phy_data {
 	struct power_supply *vbus_power_supply;
 	struct notifier_block vbus_power_nb;
 	bool vbus_power_nb_registered;
+	bool force_session_end;
 	int id_det_irq;
 	int vbus_det_irq;
 	int id_det;
@@ -179,12 +182,14 @@ static void sun4i_usb_phy_write(struct sun4i_usb_phy *phy, u32 addr, u32 data,
 	struct sun4i_usb_phy_data *phy_data = to_sun4i_usb_phy_data(phy);
 	u32 temp, usbc_bit = BIT(phy->index * 2);
 	void __iomem *phyctl = phy_data->base + phy_data->cfg->phyctl_offset;
+	unsigned long flags;
 	int i;
 
-	mutex_lock(&phy_data->mutex);
+	spin_lock_irqsave(&phy_data->reg_lock, flags);
 
-	if (phy_data->cfg->type == sun8i_a33_phy) {
-		/* A33 needs us to set phyctl to 0 explicitly */
+	if (phy_data->cfg->type == sun8i_a33_phy ||
+	    phy_data->cfg->type == sun50i_a64_phy) {
+		/* A33 or A64 needs us to set phyctl to 0 explicitly */
 		writel(0, phyctl);
 	}
 
@@ -218,7 +223,8 @@ static void sun4i_usb_phy_write(struct sun4i_usb_phy *phy, u32 addr, u32 data,
 
 		data >>= 1;
 	}
-	mutex_unlock(&phy_data->mutex);
+
+	spin_unlock_irqrestore(&phy_data->reg_lock, flags);
 }
 
 static void sun4i_usb_phy_passby(struct sun4i_usb_phy *phy, int enable)
@@ -258,14 +264,16 @@ static int sun4i_usb_phy_init(struct phy *_phy)
 		return ret;
 	}
 
+	if (data->cfg->enable_pmu_unk1) {
+		val = readl(phy->pmu + REG_PMU_UNK1);
+		writel(val & ~2, phy->pmu + REG_PMU_UNK1);
+	}
+
 	if (data->cfg->type == sun8i_h3_phy) {
 		if (phy->index == 0) {
 			val = readl(data->base + REG_PHY_UNK_H3);
 			writel(val & ~1, data->base + REG_PHY_UNK_H3);
 		}
-
-		val = readl(phy->pmu + REG_PMU_UNK_H3);
-		writel(val & ~2, phy->pmu + REG_PMU_UNK_H3);
 	} else {
 		/* Enable USB 45 Ohm resistor calibration */
 		if (phy->index == 0)
@@ -320,7 +328,10 @@ static int sun4i_usb_phy0_get_id_det(struct sun4i_usb_phy_data *data)
 {
 	switch (data->dr_mode) {
 	case USB_DR_MODE_OTG:
+		if (data->id_det_gpio)
 			return gpiod_get_value_cansleep(data->id_det_gpio);
+		else
+			return 1; /* Fallback to peripheral mode */
 	case USB_DR_MODE_HOST:
 		return 0;
 	case USB_DR_MODE_PERIPHERAL:
@@ -382,8 +393,10 @@ static int sun4i_usb_phy_power_on(struct phy *_phy)
 
 	/* For phy0 only turn on Vbus if we don't have an ext. Vbus */
 	if (phy->index == 0 && sun4i_usb_phy0_have_vbus_det(data) &&
-				data->vbus_det)
+				data->vbus_det) {
+		dev_warn(&_phy->dev, "External vbus detected, not enabling our own vbus\n");
 		return 0;
+	}
 
 	ret = regulator_enable(phy->vbus);
 	if (ret)
@@ -419,6 +432,35 @@ static int sun4i_usb_phy_power_off(struct phy *_phy)
 	return 0;
 }
 
+static int sun4i_usb_phy_set_mode(struct phy *_phy, enum phy_mode mode)
+{
+	struct sun4i_usb_phy *phy = phy_get_drvdata(_phy);
+	struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy);
+
+	if (phy->index != 0)
+		return -EINVAL;
+
+	switch (mode) {
+	case PHY_MODE_USB_HOST:
+		data->dr_mode = USB_DR_MODE_HOST;
+		break;
+	case PHY_MODE_USB_DEVICE:
+		data->dr_mode = USB_DR_MODE_PERIPHERAL;
+		break;
+	case PHY_MODE_USB_OTG:
+		data->dr_mode = USB_DR_MODE_OTG;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	dev_info(&_phy->dev, "Changing dr_mode to %d\n", (int)data->dr_mode);
+	data->force_session_end = true;
+	queue_delayed_work(system_wq, &data->detect, 0);
+
+	return 0;
+}
+
 void sun4i_usb_phy_set_squelch_detect(struct phy *_phy, bool enabled)
 {
 	struct sun4i_usb_phy *phy = phy_get_drvdata(_phy);
@@ -432,6 +474,7 @@ static const struct phy_ops sun4i_usb_phy_ops = {
 	.exit		= sun4i_usb_phy_exit,
 	.power_on	= sun4i_usb_phy_power_on,
 	.power_off	= sun4i_usb_phy_power_off,
+	.set_mode	= sun4i_usb_phy_set_mode,
 	.owner		= THIS_MODULE,
 };
 
@@ -440,7 +483,8 @@ static void sun4i_usb_phy0_id_vbus_det_scan(struct work_struct *work)
 	struct sun4i_usb_phy_data *data =
 		container_of(work, struct sun4i_usb_phy_data, detect.work);
 	struct phy *phy0 = data->phys[0].phy;
-	int id_det, vbus_det, id_notify = 0, vbus_notify = 0;
+	bool force_session_end, id_notify = false, vbus_notify = false;
+	int id_det, vbus_det;
 
 	if (phy0 == NULL)
 		return;
@@ -455,27 +499,30 @@ static void sun4i_usb_phy0_id_vbus_det_scan(struct work_struct *work)
 		return;
 	}
 
+	force_session_end = data->force_session_end;
+	data->force_session_end = false;
+
 	if (id_det != data->id_det) {
-		/*
-		 * When a host cable (id == 0) gets plugged in on systems
-		 * without vbus detection report vbus low for long enough for
-		 * the musb-ip to end the current device session.
-		 */
+		/* id-change, force session end if we've no vbus detection */
 		if (data->dr_mode == USB_DR_MODE_OTG &&
-		    !sun4i_usb_phy0_have_vbus_det(data) && id_det == 0) {
+		    !sun4i_usb_phy0_have_vbus_det(data))
+			force_session_end = true;
+
+		/* When entering host mode (id = 0) force end the session now */
+		if (force_session_end && id_det == 0) {
 			sun4i_usb_phy0_set_vbus_detect(phy0, 0);
 			msleep(200);
 			sun4i_usb_phy0_set_vbus_detect(phy0, 1);
 		}
 		sun4i_usb_phy0_set_id_detect(phy0, id_det);
 		data->id_det = id_det;
-		id_notify = 1;
+		id_notify = true;
 	}
 
 	if (vbus_det != data->vbus_det) {
 		sun4i_usb_phy0_set_vbus_detect(phy0, vbus_det);
 		data->vbus_det = vbus_det;
-		vbus_notify = 1;
+		vbus_notify = true;
 	}
 
 	mutex_unlock(&phy0->mutex);
@@ -483,13 +530,8 @@ static void sun4i_usb_phy0_id_vbus_det_scan(struct work_struct *work)
 	if (id_notify) {
 		extcon_set_cable_state_(data->extcon, EXTCON_USB_HOST,
 					!id_det);
-		/*
-		 * When a host cable gets unplugged (id == 1) on systems
-		 * without vbus detection report vbus low for long enough to
-		 * the musb-ip to end the current host session.
-		 */
-		if (data->dr_mode == USB_DR_MODE_OTG &&
-		    !sun4i_usb_phy0_have_vbus_det(data) && id_det == 1) {
+		/* When leaving host mode force end the session here */
+		if (force_session_end && id_det == 1) {
 			mutex_lock(&phy0->mutex);
 			sun4i_usb_phy0_set_vbus_detect(phy0, 0);
 			msleep(1000);
@@ -534,8 +576,7 @@ static struct phy *sun4i_usb_phy_xlate(struct device *dev,
 {
 	struct sun4i_usb_phy_data *data = dev_get_drvdata(dev);
 
-	if (args->args[0] < data->first_phy ||
-	    args->args[0] >= data->cfg->num_phys)
+	if (args->args[0] >= data->cfg->num_phys)
 		return ERR_PTR(-ENODEV);
 
 	return data->phys[args->args[0]].phy;
@@ -577,7 +618,7 @@ static int sun4i_usb_phy_probe(struct platform_device *pdev)
 	if (!data)
 		return -ENOMEM;
 
-	mutex_init(&data->mutex);
+	spin_lock_init(&data->reg_lock);
 	INIT_DELAYED_WORK(&data->detect, sun4i_usb_phy0_id_vbus_det_scan);
 	dev_set_drvdata(dev, data);
 	data->cfg = of_device_get_match_data(dev);
@@ -610,18 +651,8 @@ static int sun4i_usb_phy_probe(struct platform_device *pdev)
 	}
 
 	data->dr_mode = of_usb_get_dr_mode_by_phy(np, 0);
-	switch (data->dr_mode) {
-	case USB_DR_MODE_OTG:
-		/* otg without id_det makes no sense, and is not supported */
-		if (!data->id_det_gpio) {
-			dev_err(dev, "usb0_id_det missing or invalid\n");
-			return -ENODEV;
-		}
-		/* fall through */
-	case USB_DR_MODE_HOST:
-	case USB_DR_MODE_PERIPHERAL:
-		data->extcon = devm_extcon_dev_allocate(dev,
-							sun4i_usb_phy0_cable);
+
+	data->extcon = devm_extcon_dev_allocate(dev, sun4i_usb_phy0_cable);
 	if (IS_ERR(data->extcon))
 		return PTR_ERR(data->extcon);
 
@@ -630,13 +661,8 @@ static int sun4i_usb_phy_probe(struct platform_device *pdev)
 		dev_err(dev, "failed to register extcon: %d\n", ret);
 		return ret;
 	}
-		break;
-	default:
-		dev_info(dev, "dr_mode unknown, not registering usb phy0\n");
-		data->first_phy = 1;
-	}
 
-	for (i = data->first_phy; i < data->cfg->num_phys; i++) {
+	for (i = 0; i < data->cfg->num_phys; i++) {
 		struct sun4i_usb_phy *phy = data->phys + i;
 		char name[16];
 
@@ -737,6 +763,7 @@ static const struct sun4i_usb_phy_cfg sun4i_a10_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A10,
 	.dedicated_clocks = false,
+	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun5i_a13_cfg = {
@@ -745,6 +772,7 @@ static const struct sun4i_usb_phy_cfg sun5i_a13_cfg = {
 	.disc_thresh = 2,
 	.phyctl_offset = REG_PHYCTL_A10,
 	.dedicated_clocks = false,
+	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun6i_a31_cfg = {
@@ -753,6 +781,7 @@ static const struct sun4i_usb_phy_cfg sun6i_a31_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A10,
 	.dedicated_clocks = true,
+	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun7i_a20_cfg = {
@@ -761,6 +790,7 @@ static const struct sun4i_usb_phy_cfg sun7i_a20_cfg = {
 	.disc_thresh = 2,
 	.phyctl_offset = REG_PHYCTL_A10,
 	.dedicated_clocks = false,
+	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun8i_a23_cfg = {
@@ -769,6 +799,7 @@ static const struct sun4i_usb_phy_cfg sun8i_a23_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A10,
 	.dedicated_clocks = true,
+	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
@@ -777,6 +808,7 @@ static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
 	.disc_thresh = 3,
 	.phyctl_offset = REG_PHYCTL_A33,
 	.dedicated_clocks = true,
+	.enable_pmu_unk1 = false,
 };
 
 static const struct sun4i_usb_phy_cfg sun8i_h3_cfg = {
@@ -784,6 +816,16 @@ static const struct sun4i_usb_phy_cfg sun8i_h3_cfg = {
 	.type = sun8i_h3_phy,
 	.disc_thresh = 3,
 	.dedicated_clocks = true,
+	.enable_pmu_unk1 = true,
+};
+
+static const struct sun4i_usb_phy_cfg sun50i_a64_cfg = {
+	.num_phys = 2,
+	.type = sun50i_a64_phy,
+	.disc_thresh = 3,
+	.phyctl_offset = REG_PHYCTL_A33,
+	.dedicated_clocks = true,
+	.enable_pmu_unk1 = true,
 };
 
 static const struct of_device_id sun4i_usb_phy_of_match[] = {
@@ -794,6 +836,8 @@ static const struct of_device_id sun4i_usb_phy_of_match[] = {
 	{ .compatible = "allwinner,sun8i-a23-usb-phy", .data = &sun8i_a23_cfg },
 	{ .compatible = "allwinner,sun8i-a33-usb-phy", .data = &sun8i_a33_cfg },
 	{ .compatible = "allwinner,sun8i-h3-usb-phy", .data = &sun8i_h3_cfg },
+	{ .compatible = "allwinner,sun50i-a64-usb-phy",
+	  .data = &sun50i_a64_cfg},
 	{ },
 };
 MODULE_DEVICE_TABLE(of, sun4i_usb_phy_of_match);

drivers/phy/phy-twl4030-usb.c

@@ -172,6 +172,7 @@ struct twl4030_usb {
 	int			irq;
 	enum musb_vbus_id_status linkstat;
 	bool			vbus_supplied;
+	bool			musb_mailbox_pending;
 
 	struct delayed_work	id_workaround_work;
 };
@@ -439,6 +440,17 @@ static int __maybe_unused twl4030_usb_runtime_resume(struct device *dev)
 			  (PHY_CLK_CTRL_CLOCKGATING_EN |
 			   PHY_CLK_CTRL_CLK32K_EN));
 
+	twl4030_i2c_access(twl, 1);
+	twl4030_usb_set_mode(twl, twl->usb_mode);
+	if (twl->usb_mode == T2_USB_MODE_ULPI)
+		twl4030_i2c_access(twl, 0);
+	/*
+	 * According to the TPS65950 TRM, there has to be at least 50ms
+	 * delay between setting POWER_CTRL_OTG_ENAB and enabling charging
+	 * so wait here so that a fully enabled phy can be expected after
+	 * resume
+	 */
+	msleep(50);
 	return 0;
 }
 
@@ -459,11 +471,6 @@ static int twl4030_phy_power_on(struct phy *phy)
 
 	dev_dbg(twl->dev, "%s\n", __func__);
 	pm_runtime_get_sync(twl->dev);
-	twl4030_i2c_access(twl, 1);
-	twl4030_usb_set_mode(twl, twl->usb_mode);
-	if (twl->usb_mode == T2_USB_MODE_ULPI)
-		twl4030_i2c_access(twl, 0);
-	twl->linkstat = MUSB_UNKNOWN;
 	schedule_delayed_work(&twl->id_workaround_work, HZ);
 
 	return 0;
@@ -569,9 +576,12 @@ static irqreturn_t twl4030_usb_irq(int irq, void *_twl)
 			pm_runtime_mark_last_busy(twl->dev);
 			pm_runtime_put_autosuspend(twl->dev);
 		}
+		twl->musb_mailbox_pending = true;
+	}
+	if (twl->musb_mailbox_pending) {
 		err = musb_mailbox(status);
-		if (err)
-			twl->linkstat = MUSB_UNKNOWN;
+		if (!err)
+			twl->musb_mailbox_pending = false;
 	}
 
 	/* don't schedule during sleep - irq works right then */
@@ -676,6 +686,7 @@ static int twl4030_usb_probe(struct platform_device *pdev)
 	twl->irq		= platform_get_irq(pdev, 0);
 	twl->vbus_supplied	= false;
 	twl->linkstat		= MUSB_UNKNOWN;
+	twl->musb_mailbox_pending = false;
 
 	twl->phy.dev		= twl->dev;
 	twl->phy.label		= "twl4030";

drivers/phy/tegra/xusb.c

@@ -18,6 +18,7 @@
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/phy/phy.h>
+#include <linux/phy/tegra/xusb.h>
 #include <linux/platform_device.h>
 #include <linux/regulator/consumer.h>
 #include <linux/reset.h>
@@ -101,7 +102,8 @@ tegra_xusb_pad_find_phy_node(struct tegra_xusb_pad *pad, unsigned int index)
 	return of_find_node_by_name(np, pad->soc->lanes[index].name);
 }
 
-int tegra_xusb_lane_lookup_function(struct tegra_xusb_lane *lane,
+static int
+tegra_xusb_lane_lookup_function(struct tegra_xusb_lane *lane,
 				    const char *function)
 {
 	unsigned int i;

include/linux/extcon.h

@@ -249,7 +249,6 @@ extern int extcon_set_state(struct extcon_dev *edev, unsigned int id,
 				   bool cable_state);
 extern int extcon_set_state_sync(struct extcon_dev *edev, unsigned int id,
 				bool cable_state);
-
 /*
  * Synchronize the state and property data for a specific external connector.
  */
@@ -359,10 +358,27 @@ static inline int extcon_set_state_sync(struct extcon_dev *edev, unsigned int id
 }
 
 static inline int extcon_sync(struct extcon_dev *edev, unsigned int id)
+<<<<<<< HEAD
+=======
+{
+	return 0;
+}
+
+static inline int extcon_get_property(struct extcon_dev *edev, unsigned int id,
+					unsigned int prop,
+					union extcon_property_value *prop_val)
+{
+	return 0;
+}
+static inline int extcon_set_property(struct extcon_dev *edev, unsigned int id,
+					unsigned int prop,
+					union extcon_property_value prop_val)
+>>>>>>> next
 {
 	return 0;
 }
 
+<<<<<<< HEAD
 static inline int extcon_get_property(struct extcon_dev *edev, unsigned int id,
 					unsigned int prop,
 					union extcon_property_value *prop_val)
@@ -371,24 +387,36 @@ static inline int extcon_get_property(struct extcon_dev *edev, unsigned int id,
 }
 static inline int extcon_set_property(struct extcon_dev *edev, unsigned int id,
 					unsigned int prop,
+=======
+static inline int extcon_set_property_sync(struct extcon_dev *edev,
+					unsigned int id, unsigned int prop,
+>>>>>>> next
 					union extcon_property_value prop_val)
 {
 	return 0;
 }
 
+<<<<<<< HEAD
 static inline int extcon_set_property_sync(struct extcon_dev *edev,
 					unsigned int id, unsigned int prop,
 					union extcon_property_value prop_val)
+=======
+static inline int extcon_get_property_capability(struct extcon_dev *edev,
+					unsigned int id, unsigned int prop)
+>>>>>>> next
 {
 	return 0;
 }
 
+<<<<<<< HEAD
 static inline int extcon_get_property_capability(struct extcon_dev *edev,
 					unsigned int id, unsigned int prop)
 {
 	return 0;
 }
 
+=======
+>>>>>>> next
 static inline int extcon_set_property_capability(struct extcon_dev *edev,
 					unsigned int id, unsigned int prop)
 {

include/linux/phy/phy.h

@@ -36,6 +36,7 @@ enum phy_mode {
  * @power_on: powering on the phy
  * @power_off: powering off the phy
  * @set_mode: set the mode of the phy
+ * @reset: resetting the phy
  * @owner: the module owner containing the ops
  */
 struct phy_ops {
@@ -44,6 +45,7 @@ struct phy_ops {
 	int	(*power_on)(struct phy *phy);
 	int	(*power_off)(struct phy *phy);
 	int	(*set_mode)(struct phy *phy, enum phy_mode mode);
+	int	(*reset)(struct phy *phy);
 	struct module *owner;
 };
 
@@ -136,6 +138,7 @@ int phy_exit(struct phy *phy);
 int phy_power_on(struct phy *phy);
 int phy_power_off(struct phy *phy);
 int phy_set_mode(struct phy *phy, enum phy_mode mode);
+int phy_reset(struct phy *phy);
 static inline int phy_get_bus_width(struct phy *phy)
 {
 	return phy->attrs.bus_width;