提交 c95cf3d0 编写于 作者: D David-John Willis 提交者: John W. Linville

wl1251: add NVS in EEPROM support

wl1251 supports also that NVS is stored in a separate EEPROM, add support
for that.

kvalo: use platform data instead Kconfig and use kernel style
Signed-off-by: NDavid-John Willis <John.Willis@Distant-earth.com>
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
上级 7010193a
......@@ -269,6 +269,7 @@ struct wl1251 {
void (*set_power)(bool enable);
int irq;
bool use_eeprom;
enum wl1251_state state;
struct mutex mutex;
......
......@@ -494,6 +494,11 @@ int wl1251_boot(struct wl1251 *wl)
goto out;
/* 2. start processing NVS file */
if (wl->use_eeprom) {
wl1251_reg_write32(wl, ACX_REG_EE_START, START_EEPROM_MGR);
msleep(4000);
wl1251_reg_write32(wl, ACX_EEPROMLESS_IND_REG, USE_EEPROM);
} else {
ret = wl1251_boot_upload_nvs(wl);
if (ret < 0)
goto out;
......@@ -501,6 +506,7 @@ int wl1251_boot(struct wl1251 *wl)
/* write firmware's last address (ie. it's length) to
* ACX_EEPROMLESS_IND_REG */
wl1251_reg_write32(wl, ACX_EEPROMLESS_IND_REG, wl->fw_len);
}
/* 6. read the EEPROM parameters */
tmp = wl1251_reg_read32(wl, SCR_PAD2);
......
......@@ -370,6 +370,7 @@ enum wl12xx_acx_int_reg {
EEPROM location specified in the EE_ADDR register.
The Wlan hardware hardware clears this bit automatically.
*===============================================*/
#define EE_CTL (REGISTERS_BASE + 0x2000)
#define ACX_EE_CTL_REG EE_CTL
#define EE_WRITE 0x00000001ul
#define EE_READ 0x00000002ul
......@@ -380,6 +381,7 @@ enum wl12xx_acx_int_reg {
This register specifies the address
within the EEPROM from/to which to read/write data.
===============================================*/
#define EE_ADDR (REGISTERS_BASE + 0x2008)
#define ACX_EE_ADDR_REG EE_ADDR
/*===============================================
......@@ -389,8 +391,12 @@ enum wl12xx_acx_int_reg {
data from the EEPROM or the write data
to be written to the EEPROM.
===============================================*/
#define EE_DATA (REGISTERS_BASE + 0x2004)
#define ACX_EE_DATA_REG EE_DATA
#define EEPROM_ACCESS_TO 10000 /* timeout counter */
#define START_EEPROM_MGR 0x00000001
/*===============================================
EEPROM Base Address - 32bit RW
------------------------------------------
......
......@@ -270,6 +270,8 @@ static int __devinit wl1251_spi_probe(struct spi_device *spi)
return -ENODEV;
}
wl->use_eeprom = pdata->use_eeprom;
ret = request_irq(wl->irq, wl1251_irq, 0, DRIVER_NAME, wl);
if (ret < 0) {
wl1251_error("request_irq() failed: %d", ret);
......
......@@ -26,6 +26,7 @@
struct wl12xx_platform_data {
void (*set_power)(bool enable);
bool use_eeprom;
};
#endif
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册