Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next

Jeff Kirsher says:

====================
This series contains updates to ethtool.h, e1000, e1000e, and igb to
implement MDI/MDIx control.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/ethernet/intel/e1000/e1000_ethtool.c

@@ -174,6 +174,20 @@ static int e1000_get_settings(struct net_device *netdev,
 
 	ecmd->autoneg = ((hw->media_type == e1000_media_type_fiber) ||
 			 hw->autoneg) ? AUTONEG_ENABLE : AUTONEG_DISABLE;
+
+	/* MDI-X => 1; MDI => 0 */
+	if ((hw->media_type == e1000_media_type_copper) &&
+	    netif_carrier_ok(netdev))
+		ecmd->eth_tp_mdix = (!!adapter->phy_info.mdix_mode ?
+							ETH_TP_MDI_X :
+							ETH_TP_MDI);
+	else
+		ecmd->eth_tp_mdix = ETH_TP_MDI_INVALID;
+
+	if (hw->mdix == AUTO_ALL_MODES)
+		ecmd->eth_tp_mdix_ctrl = ETH_TP_MDI_AUTO;
+	else
+		ecmd->eth_tp_mdix_ctrl = hw->mdix;
 	return 0;
 }
 
@@ -183,6 +197,22 @@ static int e1000_set_settings(struct net_device *netdev,
 	struct e1000_adapter *adapter = netdev_priv(netdev);
 	struct e1000_hw *hw = &adapter->hw;
 
+	/*
+	 * MDI setting is only allowed when autoneg enabled because
+	 * some hardware doesn't allow MDI setting when speed or
+	 * duplex is forced.
+	 */
+	if (ecmd->eth_tp_mdix_ctrl) {
+		if (hw->media_type != e1000_media_type_copper)
+			return -EOPNOTSUPP;
+
+		if ((ecmd->eth_tp_mdix_ctrl != ETH_TP_MDI_AUTO) &&
+		    (ecmd->autoneg != AUTONEG_ENABLE)) {
+			e_err(drv, "forcing MDI/MDI-X state is not supported when link speed and/or duplex are forced\n");
+			return -EINVAL;
+		}
+	}
+
 	while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
 		msleep(1);
 
@@ -199,12 +229,21 @@ static int e1000_set_settings(struct net_device *netdev,
 		ecmd->advertising = hw->autoneg_advertised;
 	} else {
 		u32 speed = ethtool_cmd_speed(ecmd);
+		/* calling this overrides forced MDI setting */
 		if (e1000_set_spd_dplx(adapter, speed, ecmd->duplex)) {
 			clear_bit(__E1000_RESETTING, &adapter->flags);
 			return -EINVAL;
 		}
 	}
 
+	/* MDI-X => 2; MDI => 1; Auto => 3 */
+	if (ecmd->eth_tp_mdix_ctrl) {
+		if (ecmd->eth_tp_mdix_ctrl == ETH_TP_MDI_AUTO)
+			hw->mdix = AUTO_ALL_MODES;
+		else
+			hw->mdix = ecmd->eth_tp_mdix_ctrl;
+	}
+
 	/* reset the link */
 
 	if (netif_running(adapter->netdev)) {

drivers/net/ethernet/intel/e1000/e1000_main.c

@@ -4939,6 +4939,10 @@ int e1000_set_spd_dplx(struct e1000_adapter *adapter, u32 spd, u8 dplx)
 	default:
 		goto err_inval;
 	}
+
+	/* clear MDI, MDI(-X) override is only allowed when autoneg enabled */
+	hw->mdix = AUTO_ALL_MODES;
+
 	return 0;
 
 err_inval:

drivers/net/ethernet/intel/e1000e/ethtool.c

@@ -199,6 +199,11 @@ static int e1000_get_settings(struct net_device *netdev,
 	else
 		ecmd->eth_tp_mdix = ETH_TP_MDI_INVALID;
 
+	if (hw->phy.mdix == AUTO_ALL_MODES)
+		ecmd->eth_tp_mdix_ctrl = ETH_TP_MDI_AUTO;
+	else
+		ecmd->eth_tp_mdix_ctrl = hw->phy.mdix;
+
 	return 0;
 }
 
@@ -241,6 +246,10 @@ static int e1000_set_spd_dplx(struct e1000_adapter *adapter, u32 spd, u8 dplx)
 	default:
 		goto err_inval;
 	}
+
+	/* clear MDI, MDI(-X) override is only allowed when autoneg enabled */
+	adapter->hw.phy.mdix = AUTO_ALL_MODES;
+
 	return 0;
 
 err_inval:
@@ -264,6 +273,22 @@ static int e1000_set_settings(struct net_device *netdev,
 		return -EINVAL;
 	}
 
+	/*
+	 * MDI setting is only allowed when autoneg enabled because
+	 * some hardware doesn't allow MDI setting when speed or
+	 * duplex is forced.
+	 */
+	if (ecmd->eth_tp_mdix_ctrl) {
+		if (hw->phy.media_type != e1000_media_type_copper)
+			return -EOPNOTSUPP;
+
+		if ((ecmd->eth_tp_mdix_ctrl != ETH_TP_MDI_AUTO) &&
+		    (ecmd->autoneg != AUTONEG_ENABLE)) {
+			e_err("forcing MDI/MDI-X state is not supported when link speed and/or duplex are forced\n");
+			return -EINVAL;
+		}
+	}
+
 	while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
 		usleep_range(1000, 2000);
 
@@ -282,20 +307,32 @@ static int e1000_set_settings(struct net_device *netdev,
 			hw->fc.requested_mode = e1000_fc_default;
 	} else {
 		u32 speed = ethtool_cmd_speed(ecmd);
+		/* calling this overrides forced MDI setting */
 		if (e1000_set_spd_dplx(adapter, speed, ecmd->duplex)) {
 			clear_bit(__E1000_RESETTING, &adapter->state);
 			return -EINVAL;
 		}
 	}
 
+	/* MDI-X => 2; MDI => 1; Auto => 3 */
+	if (ecmd->eth_tp_mdix_ctrl) {
+		/*
+		 * fix up the value for auto (3 => 0) as zero is mapped
+		 * internally to auto
+		 */
+		if (ecmd->eth_tp_mdix_ctrl == ETH_TP_MDI_AUTO)
+			hw->phy.mdix = AUTO_ALL_MODES;
+		else
+			hw->phy.mdix = ecmd->eth_tp_mdix_ctrl;
+	}
+
 	/* reset the link */
 
 	if (netif_running(adapter->netdev)) {
 		e1000e_down(adapter);
 		e1000e_up(adapter);
-	} else {
+	} else
 		e1000e_reset(adapter);
-	}
 
 	clear_bit(__E1000_RESETTING, &adapter->state);
 	return 0;

drivers/net/ethernet/intel/e1000e/phy.c

@@ -84,8 +84,9 @@ static const u16 e1000_igp_2_cable_length_table[] = {
 #define I82577_PHY_STATUS2_SPEED_1000MBPS 0x0200
 
 /* I82577 PHY Control 2 */
-#define I82577_PHY_CTRL2_AUTO_MDIX        0x0400
-#define I82577_PHY_CTRL2_FORCE_MDI_MDIX   0x0200
+#define I82577_PHY_CTRL2_MANUAL_MDIX      0x0200
+#define I82577_PHY_CTRL2_AUTO_MDI_MDIX    0x0400
+#define I82577_PHY_CTRL2_MDIX_CFG_MASK    0x0600
 
 /* I82577 PHY Diagnostics Status */
 #define I82577_DSTATUS_CABLE_LENGTH       0x03FC
@@ -702,6 +703,32 @@ s32 e1000_copper_link_setup_82577(struct e1000_hw *hw)
 	if (ret_val)
 		return ret_val;
 
+	/* Set MDI/MDIX mode */
+	ret_val = e1e_rphy(hw, I82577_PHY_CTRL_2, &phy_data);
+	if (ret_val)
+		return ret_val;
+	phy_data &= ~I82577_PHY_CTRL2_MDIX_CFG_MASK;
+	/*
+	 * Options:
+	 *   0 - Auto (default)
+	 *   1 - MDI mode
+	 *   2 - MDI-X mode
+	 */
+	switch (hw->phy.mdix) {
+	case 1:
+		break;
+	case 2:
+		phy_data |= I82577_PHY_CTRL2_MANUAL_MDIX;
+		break;
+	case 0:
+	default:
+		phy_data |= I82577_PHY_CTRL2_AUTO_MDI_MDIX;
+		break;
+	}
+	ret_val = e1e_wphy(hw, I82577_PHY_CTRL_2, phy_data);
+	if (ret_val)
+		return ret_val;
+
 	return e1000_set_master_slave_mode(hw);
 }
 

drivers/net/ethernet/intel/igb/e1000_phy.c

@@ -464,6 +464,32 @@ s32 igb_copper_link_setup_82580(struct e1000_hw *hw)
 	phy_data |= I82580_CFG_ENABLE_DOWNSHIFT;
 
 	ret_val = phy->ops.write_reg(hw, I82580_CFG_REG, phy_data);
+	if (ret_val)
+		goto out;
+
+	/* Set MDI/MDIX mode */
+	ret_val = phy->ops.read_reg(hw, I82580_PHY_CTRL_2, &phy_data);
+	if (ret_val)
+		goto out;
+	phy_data &= ~I82580_PHY_CTRL2_MDIX_CFG_MASK;
+	/*
+	 * Options:
+	 *   0 - Auto (default)
+	 *   1 - MDI mode
+	 *   2 - MDI-X mode
+	 */
+	switch (hw->phy.mdix) {
+	case 1:
+		break;
+	case 2:
+		phy_data |= I82580_PHY_CTRL2_MANUAL_MDIX;
+		break;
+	case 0:
+	default:
+		phy_data |= I82580_PHY_CTRL2_AUTO_MDI_MDIX;
+		break;
+	}
+	ret_val = hw->phy.ops.write_reg(hw, I82580_PHY_CTRL_2, phy_data);
 
 out:
 	return ret_val;
@@ -2246,8 +2272,7 @@ s32 igb_phy_force_speed_duplex_82580(struct e1000_hw *hw)
 	if (ret_val)
 		goto out;
 
-	phy_data &= ~I82580_PHY_CTRL2_AUTO_MDIX;
-	phy_data &= ~I82580_PHY_CTRL2_FORCE_MDI_MDIX;
+	phy_data &= ~I82580_PHY_CTRL2_MDIX_CFG_MASK;
 
 	ret_val = phy->ops.write_reg(hw, I82580_PHY_CTRL_2, phy_data);
 	if (ret_val)

drivers/net/ethernet/intel/igb/e1000_phy.h

@@ -111,8 +111,9 @@ s32  igb_check_polarity_m88(struct e1000_hw *hw);
 #define I82580_PHY_STATUS2_SPEED_100MBPS  0x0100
 
 /* I82580 PHY Control 2 */
-#define I82580_PHY_CTRL2_AUTO_MDIX        0x0400
-#define I82580_PHY_CTRL2_FORCE_MDI_MDIX   0x0200
+#define I82580_PHY_CTRL2_MANUAL_MDIX      0x0200
+#define I82580_PHY_CTRL2_AUTO_MDI_MDIX    0x0400
+#define I82580_PHY_CTRL2_MDIX_CFG_MASK    0x0600
 
 /* I82580 PHY Diagnostics Status */
 #define I82580_DSTATUS_CABLE_LENGTH       0x03FC

drivers/net/ethernet/intel/igb/igb_ethtool.c

@@ -198,6 +198,19 @@ static int igb_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd)
 	}
 
 	ecmd->autoneg = hw->mac.autoneg ? AUTONEG_ENABLE : AUTONEG_DISABLE;
+
+	/* MDI-X => 2; MDI =>1; Invalid =>0 */
+	if (hw->phy.media_type == e1000_media_type_copper)
+		ecmd->eth_tp_mdix = hw->phy.is_mdix ? ETH_TP_MDI_X :
+						      ETH_TP_MDI;
+	else
+		ecmd->eth_tp_mdix = ETH_TP_MDI_INVALID;
+
+	if (hw->phy.mdix == AUTO_ALL_MODES)
+		ecmd->eth_tp_mdix_ctrl = ETH_TP_MDI_AUTO;
+	else
+		ecmd->eth_tp_mdix_ctrl = hw->phy.mdix;
+
 	return 0;
 }
 
@@ -214,6 +227,22 @@ static int igb_set_settings(struct net_device *netdev, struct ethtool_cmd *ecmd)
 		return -EINVAL;
 	}
 
+	/*
+	 * MDI setting is only allowed when autoneg enabled because
+	 * some hardware doesn't allow MDI setting when speed or
+	 * duplex is forced.
+	 */
+	if (ecmd->eth_tp_mdix_ctrl) {
+		if (hw->phy.media_type != e1000_media_type_copper)
+			return -EOPNOTSUPP;
+
+		if ((ecmd->eth_tp_mdix_ctrl != ETH_TP_MDI_AUTO) &&
+		    (ecmd->autoneg != AUTONEG_ENABLE)) {
+			dev_err(&adapter->pdev->dev, "forcing MDI/MDI-X state is not supported when link speed and/or duplex are forced\n");
+			return -EINVAL;
+		}
+	}
+
 	while (test_and_set_bit(__IGB_RESETTING, &adapter->state))
 		msleep(1);
 
@@ -227,12 +256,25 @@ static int igb_set_settings(struct net_device *netdev, struct ethtool_cmd *ecmd)
 			hw->fc.requested_mode = e1000_fc_default;
 	} else {
 		u32 speed = ethtool_cmd_speed(ecmd);
+		/* calling this overrides forced MDI setting */
 		if (igb_set_spd_dplx(adapter, speed, ecmd->duplex)) {
 			clear_bit(__IGB_RESETTING, &adapter->state);
 			return -EINVAL;
 		}
 	}
 
+	/* MDI-X => 2; MDI => 1; Auto => 3 */
+	if (ecmd->eth_tp_mdix_ctrl) {
+		/*
+		 * fix up the value for auto (3 => 0) as zero is mapped
+		 * internally to auto
+		 */
+		if (ecmd->eth_tp_mdix_ctrl == ETH_TP_MDI_AUTO)
+			hw->phy.mdix = AUTO_ALL_MODES;
+		else
+			hw->phy.mdix = ecmd->eth_tp_mdix_ctrl;
+	}
+
 	/* reset the link */
 	if (netif_running(adapter->netdev)) {
 		igb_down(adapter);

drivers/net/ethernet/intel/igb/igb_main.c

@@ -6675,6 +6675,10 @@ int igb_set_spd_dplx(struct igb_adapter *adapter, u32 spd, u8 dplx)
 	default:
 		goto err_inval;
 	}
+
+	/* clear MDI, MDI(-X) override is only allowed when autoneg enabled */
+	adapter->hw.phy.mdix = AUTO_ALL_MODES;
+
 	return 0;
 
 err_inval:

include/linux/ethtool.h

@@ -45,8 +45,10 @@ struct ethtool_cmd {
 				 * bits) in Mbps. Please use
 				 * ethtool_cmd_speed()/_set() to
 				 * access it */
-	__u8	eth_tp_mdix;
-	__u8	reserved2;
+	__u8	eth_tp_mdix;	/* twisted pair MDI-X status */
+	__u8    eth_tp_mdix_ctrl; /* twisted pair MDI-X control, when set,
+				   * link should be renegotiated if necessary
+				   */
 	__u32	lp_advertising;	/* Features the link partner advertises */
 	__u32	reserved[2];
 };
@@ -1229,10 +1231,13 @@ struct ethtool_ops {
 #define AUTONEG_DISABLE		0x00
 #define AUTONEG_ENABLE		0x01
 
-/* Mode MDI or MDI-X */
-#define ETH_TP_MDI_INVALID	0x00
-#define ETH_TP_MDI		0x01
-#define ETH_TP_MDI_X		0x02
+/* MDI or MDI-X status/control - if MDI/MDI_X/AUTO is set then
+ * the driver is required to renegotiate link
+ */
+#define ETH_TP_MDI_INVALID	0x00 /* status: unknown; control: unsupported */
+#define ETH_TP_MDI		0x01 /* status: MDI;     control: force MDI */
+#define ETH_TP_MDI_X		0x02 /* status: MDI-X;   control: force MDI-X */
+#define ETH_TP_MDI_AUTO		0x03 /*                  control: auto-select */
 
 /* Wake-On-Lan options. */
 #define WAKE_PHY		(1 << 0)