Merge tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd

Pull MTD updates from Brian Norris:
 "NAND, from Boris:
   - some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
     davinci, brcmnand, omap)
   - a huge cleanup/rework of the denali driver accompanied with core
     fixes/improvements to simplify the driver code
   - a complete rewrite of the atmel driver to support new DT bindings
     make future evolution easier
   - the addition of per-vendor detection/initialization steps to avoid
     extending the nand_ids table with more extended-id entries

  SPI NOR, from Cyrille:
   - fixes in the hisi, intel and Mediatek SPI controller drivers
   - fixes to some SPI flash memories not supporting the Chip Erase
     command.
   - add support to some new memory parts (Winbond, Macronix, Micron,
     ESMT).
   - add new driver for the STM32 QSPI controller

  And a few fixes for Gemini and Versatile platforms on physmap-of"

* tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd: (100 commits)
  MAINTAINERS: Update NAND subsystem git repositories
  mtd: nand: gpio: update binding
  mtd: nand: add ooblayout for old hamming layout
  mtd: oxnas_nand: Allocating more than necessary in probe()
  dt-bindings: mtd: Document the STM32 QSPI bindings
  mtd: mtk-nor: set controller's address width according to nor flash
  mtd: spi-nor: add driver for STM32 quad spi flash controller
  mtd: nand: brcmnand: Check flash #WP pin status before nand erase/program
  mtd: nand: davinci: add comment on NAND subpage write status on keystone
  mtd: nand: omap2: Fix partition creation via cmdline mtdparts
  mtd: nand: NULL terminate a of_device_id table
  mtd: nand: Fix a couple error codes
  mtd: nand: allow drivers to request minimum alignment for passed buffer
  mtd: nand: allocate aligned buffers if NAND_OWN_BUFFERS is unset
  mtd: nand: denali: allow to override revision number
  mtd: nand: denali_dt: use pdev instead of ofdev for platform_device
  mtd: nand: denali_dt: remove dma-mask DT property
  mtd: nand: denali: support 64bit capable DMA engine
  mtd: nand: denali_dt: enable HW_ECC_FIXUP for Altera SOCFPGA variant
  mtd: nand: denali: support HW_ECC_FIXUP capability
  ...

Documentation/devicetree/bindings/mtd/atmel-nand.txt

-Atmel NAND flash
+Atmel NAND flash controller bindings
+
+The NAND flash controller node should be defined under the EBI bus (see
+Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt).
+One or several NAND devices can be defined under this NAND controller.
+The NAND controller might be connected to an ECC engine.
+
+* NAND controller bindings:
+
+Required properties:
+- compatible: should be one of the following
+	"atmel,at91rm9200-nand-controller"
+	"atmel,at91sam9260-nand-controller"
+	"atmel,at91sam9261-nand-controller"
+	"atmel,at91sam9g45-nand-controller"
+	"atmel,sama5d3-nand-controller"
+- ranges: empty ranges property to forward EBI ranges definitions.
+- #address-cells: should be set to 2.
+- #size-cells: should be set to 1.
+- atmel,nfc-io: phandle to the NFC IO block. Only required for sama5d3
+		controllers.
+- atmel,nfc-sram: phandle to the NFC SRAM block. Only required for sama5d3
+		  controllers.
+
+Optional properties:
+- ecc-engine: phandle to the PMECC block. Only meaningful if the SoC embeds
+	      a PMECC engine.
+
+* NAND device/chip bindings:
+
+Required properties:
+- reg: describes the CS lines assigned to the NAND device. If the NAND device
+       exposes multiple CS lines (multi-dies chips), your reg property will
+       contain X tuples of 3 entries.
+       1st entry: the CS line this NAND chip is connected to
+       2nd entry: the base offset of the memory region assigned to this
+		  device (always 0)
+       3rd entry: the memory region size (always 0x800000)
+
+Optional properties:
+- rb-gpios: the GPIO(s) used to check the Ready/Busy status of the NAND.
+- cs-gpios: the GPIO(s) used to control the CS line.
+- det-gpios: the GPIO used to detect if a Smartmedia Card is present.
+- atmel,rb: an integer identifying the native Ready/Busy pin. Only meaningful
+	    on sama5 SoCs.
+
+All generic properties described in
+Documentation/devicetree/bindings/mtd/{common,nand}.txt also apply to the NAND
+device node, and NAND partitions should be defined under the NAND node as
+described in Documentation/devicetree/bindings/mtd/partition.txt.
+
+* ECC engine (PMECC) bindings:
+
+Required properties:
+- compatible: should be one of the following
+	"atmel,at91sam9g45-pmecc"
+	"atmel,sama5d4-pmecc"
+	"atmel,sama5d2-pmecc"
+- reg: should contain 2 register ranges. The first one is pointing to the PMECC
+       block, and the second one to the PMECC_ERRLOC block.
+
+Example:
+
+	pmecc: ecc-engine@ffffc070 {
+		compatible = "atmel,at91sam9g45-pmecc";
+                reg = <0xffffc070 0x490>,
+                      <0xffffc500 0x100>;
+	};
+
+	ebi: ebi@10000000 {
+		compatible = "atmel,sama5d3-ebi";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		atmel,smc = <&hsmc>;
+		reg = <0x10000000 0x10000000
+		       0x40000000 0x30000000>;
+		ranges = <0x0 0x0 0x10000000 0x10000000
+			  0x1 0x0 0x40000000 0x10000000
+			  0x2 0x0 0x50000000 0x10000000
+			  0x3 0x0 0x60000000 0x10000000>;
+		clocks = <&mck>;
+
+                nand_controller: nand-controller {
+			compatible = "atmel,sama5d3-nand-controller";
+			atmel,nfc-sram = <&nfc_sram>;
+			atmel,nfc-io = <&nfc_io>;
+			ecc-engine = <&pmecc>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			ranges;
+
+			nand@3 {
+				reg = <0x3 0x0 0x800000>;
+				atmel,rb = <0>;
+
+				/*
+				 * Put generic NAND/MTD properties and
+				 * subnodes here.
+				 */
+			};
+		};
+	};
+
+-----------------------------------------------------------------------
+
+Deprecated bindings (should not be used in new device trees):
 
 Required properties:
 - compatible: The possible values are:

Documentation/devicetree/bindings/mtd/denali-nand.txt

 * Denali NAND controller
 
 Required properties:
-  - compatible : should be "denali,denali-nand-dt"
+  - compatible : should be one of the following:
+      "altr,socfpga-denali-nand"            - for Altera SOCFPGA
   - reg : should contain registers location and length for data and reg.
   - reg-names: Should contain the reg names "nand_data" and "denali_reg"
   - interrupts : The interrupt number.
-  - dm-mask : DMA bit mask
 
 The device tree may optionally contain sub-nodes describing partitions of the
 address space. See partition.txt for more detail.
@@ -15,9 +15,8 @@ Examples:
 nand: nand@ff900000 {
 	#address-cells = <1>;
 	#size-cells = <1>;
-	compatible = "denali,denali-nand-dt";
+	compatible = "altr,socfpga-denali-nand";
 	reg = <0xff900000 0x100000>, <0xffb80000 0x10000>;
 	reg-names = "nand_data", "denali_reg";
 	interrupts = <0 144 4>;
-	dma-mask = <0xffffffff>;
 };

Documentation/devicetree/bindings/mtd/gpio-control-nand.txt

@@ -12,7 +12,7 @@ Required properties:
 - #address-cells, #size-cells : Must be present if the device has sub-nodes
   representing partitions.
 - gpios : Specifies the GPIO pins to control the NAND device.  The order of
-  GPIO references is:  RDY, nCE, ALE, CLE, and an optional nWP.
+  GPIO references is:  RDY, nCE, ALE, CLE, and nWP. nCE and nWP are optional.
 
 Optional properties:
 - bank-width : Width (in bytes) of the device.  If not present, the width
@@ -36,7 +36,7 @@ gpio-nand@1,0 {
 	#address-cells = <1>;
 	#size-cells = <1>;
 	gpios = <&banka 1 0>,	/* RDY */
-		<&banka 2 0>, 	/* nCE */
+		<0>, 		/* nCE */
 		<&banka 3 0>, 	/* ALE */
 		<&banka 4 0>, 	/* CLE */
 		<0>;		/* nWP */

Documentation/devicetree/bindings/mtd/stm32-quadspi.txt

+* STMicroelectronics Quad Serial Peripheral Interface(QuadSPI)
+
+Required properties:
+- compatible: should be "st,stm32f469-qspi"
+- reg: the first contains the register location and length.
+       the second contains the memory mapping address and length
+- reg-names: should contain the reg names "qspi" "qspi_mm"
+- interrupts: should contain the interrupt for the device
+- clocks: the phandle of the clock needed by the QSPI controller
+- A pinctrl must be defined to set pins in mode of operation for QSPI transfer
+
+Optional properties:
+- resets: must contain the phandle to the reset controller.
+
+A spi flash must be a child of the nor_flash node and could have some
+properties. Also see jedec,spi-nor.txt.
+
+Required properties:
+- reg: chip-Select number (QSPI controller may connect 2 nor flashes)
+- spi-max-frequency: max frequency of spi bus
+
+Optional property:
+- spi-rx-bus-width: see ../spi/spi-bus.txt for the description
+
+Example:
+
+qspi: spi@a0001000 {
+	compatible = "st,stm32f469-qspi";
+	reg = <0xa0001000 0x1000>, <0x90000000 0x10000000>;
+	reg-names = "qspi", "qspi_mm";
+	interrupts = <91>;
+	resets = <&rcc STM32F4_AHB3_RESET(QSPI)>;
+	clocks = <&rcc 0 STM32F4_AHB3_CLOCK(QSPI)>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi0>;
+
+	flash@0 {
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		...
+	};
+};

MAINTAINERS

@@ -2274,7 +2274,7 @@ M:	Wenyou Yang <wenyou.yang@atmel.com>
 M:	Josh Wu <rainyfeeling@outlook.com>
 L:	linux-mtd@lists.infradead.org
 S:	Supported
-F:	drivers/mtd/nand/atmel_nand*
+F:	drivers/mtd/nand/atmel/*
 
 ATMEL SDMMC DRIVER
 M:	Ludovic Desroches <ludovic.desroches@microchip.com>
@@ -8376,12 +8376,12 @@ M:	Brian Norris <computersforpeace@gmail.com>
 M:	Boris Brezillon <boris.brezillon@free-electrons.com>
 M:	Marek Vasut <marek.vasut@gmail.com>
 M:	Richard Weinberger <richard@nod.at>
-M:	Cyrille Pitchen <cyrille.pitchen@atmel.com>
+M:	Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
 L:	linux-mtd@lists.infradead.org
 W:	http://www.linux-mtd.infradead.org/
 Q:	http://patchwork.ozlabs.org/project/linux-mtd/list/
-T:	git git://git.infradead.org/linux-mtd.git
-T:	git git://git.infradead.org/l2-mtd.git
+T:	git git://git.infradead.org/linux-mtd.git master
+T:	git git://git.infradead.org/l2-mtd.git master
 S:	Maintained
 F:	Documentation/devicetree/bindings/mtd/
 F:	drivers/mtd/
@@ -8756,7 +8756,8 @@ R:	Richard Weinberger <richard@nod.at>
 L:	linux-mtd@lists.infradead.org
 W:	http://www.linux-mtd.infradead.org/
 Q:	http://patchwork.ozlabs.org/project/linux-mtd/list/
-T:	git git://github.com/linux-nand/linux.git
+T:	git git://git.infradead.org/linux-mtd.git nand/fixes
+T:	git git://git.infradead.org/l2-mtd.git nand/next
 S:	Maintained
 F:	drivers/mtd/nand/
 F:	include/linux/mtd/nand*.h
@@ -12113,7 +12114,7 @@ S:	Maintained
 F:	drivers/clk/spear/
 
 SPI NOR SUBSYSTEM
-M:	Cyrille Pitchen <cyrille.pitchen@atmel.com>
+M:	Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
 M:	Marek Vasut <marek.vasut@gmail.com>
 L:	linux-mtd@lists.infradead.org
 W:	http://www.linux-mtd.infradead.org/

arch/cris/arch-v32/drivers/Kconfig

@@ -136,7 +136,6 @@ config ETRAX_NANDFLASH
 	bool "NAND flash support"
 	depends on ETRAX_ARCH_V32
 	select MTD_NAND
-	select MTD_NAND_IDS
 	help
 	  This option enables MTD mapping of NAND flash devices.  Needed to use
 	  NAND flash memories.  If unsure, say Y.

drivers/memory/Kconfig

@@ -116,7 +116,7 @@ config FSL_CORENET_CF
 
 config FSL_IFC
 	bool
-	depends on FSL_SOC || ARCH_LAYERSCAPE
+	depends on FSL_SOC || ARCH_LAYERSCAPE || SOC_LS1021A
 
 config JZ4780_NEMC
 	bool "Ingenic JZ4780 SoC NEMC driver"

drivers/mtd/chips/cfi_cmdset_0002.c

@@ -323,7 +323,8 @@ static void fixup_sst38vf640x_sectorsize(struct mtd_info *mtd)
 	 * it should report a size of 8KBytes (0x0020*256).
 	 */
 	cfi->cfiq->EraseRegionInfo[0] = 0x002003ff;
-	pr_warning("%s: Bad 38VF640x CFI data; adjusting sector size from 64 to 8KiB\n", mtd->name);
+	pr_warn("%s: Bad 38VF640x CFI data; adjusting sector size from 64 to 8KiB\n",
+		mtd->name);
 }
 
 static void fixup_s29gl064n_sectors(struct mtd_info *mtd)
@@ -333,7 +334,8 @@ static void fixup_s29gl064n_sectors(struct mtd_info *mtd)
 
 	if ((cfi->cfiq->EraseRegionInfo[0] & 0xffff) == 0x003f) {
 		cfi->cfiq->EraseRegionInfo[0] |= 0x0040;
-		pr_warning("%s: Bad S29GL064N CFI data; adjust from 64 to 128 sectors\n", mtd->name);
+		pr_warn("%s: Bad S29GL064N CFI data; adjust from 64 to 128 sectors\n",
+			mtd->name);
 	}
 }
 
@@ -344,7 +346,8 @@ static void fixup_s29gl032n_sectors(struct mtd_info *mtd)
 
 	if ((cfi->cfiq->EraseRegionInfo[1] & 0xffff) == 0x007e) {
 		cfi->cfiq->EraseRegionInfo[1] &= ~0x0040;
-		pr_warning("%s: Bad S29GL032N CFI data; adjust from 127 to 63 sectors\n", mtd->name);
+		pr_warn("%s: Bad S29GL032N CFI data; adjust from 127 to 63 sectors\n",
+			mtd->name);
 	}
 }
 
@@ -358,7 +361,8 @@ static void fixup_s29ns512p_sectors(struct mtd_info *mtd)
 	 * which is not permitted by CFI.
 	 */
 	cfi->cfiq->EraseRegionInfo[0] = 0x020001ff;
-	pr_warning("%s: Bad S29NS512P CFI data; adjust to 512 sectors\n", mtd->name);
+	pr_warn("%s: Bad S29NS512P CFI data; adjust to 512 sectors\n",
+		mtd->name);
 }
 
 /* Used to fix CFI-Tables of chips without Extended Query Tables */

drivers/mtd/maps/Makefile

@@ -17,12 +17,10 @@ obj-$(CONFIG_MTD_CK804XROM)	+= ck804xrom.o
 obj-$(CONFIG_MTD_TSUNAMI)	+= tsunami_flash.o
 obj-$(CONFIG_MTD_PXA2XX)	+= pxa2xx-flash.o
 obj-$(CONFIG_MTD_PHYSMAP)	+= physmap.o
-ifdef CONFIG_MTD_PHYSMAP_OF_VERSATILE
-physmap_of-objs += physmap_of_versatile.o
-endif
-ifdef CONFIG_MTD_PHYSMAP_OF_GEMINI
-physmap_of-objs += physmap_of_gemini.o
-endif
+physmap_of-objs-y		+= physmap_of_core.o
+physmap_of-objs-$(CONFIG_MTD_PHYSMAP_OF_VERSATILE) += physmap_of_versatile.o
+physmap_of-objs-$(CONFIG_MTD_PHYSMAP_OF_GEMINI) += physmap_of_gemini.o
+physmap_of-objs			:= $(physmap_of-objs-y)
 obj-$(CONFIG_MTD_PHYSMAP_OF)	+= physmap_of.o
 obj-$(CONFIG_MTD_PISMO)		+= pismo.o
 obj-$(CONFIG_MTD_PMC_MSP_EVM)   += pmcmsp-flash.o

drivers/mtd/maps/physmap_of.c → drivers/mtd/maps/physmap_of_core.c

@@ -116,32 +116,22 @@ static const char * const part_probe_types_def[] = {
 
 static const char * const *of_get_probes(struct device_node *dp)
 {
-	const char *cp;
-	int cplen;
-	unsigned int l;
-	unsigned int count;
 	const char **res;
+	int count;
 
-	cp = of_get_property(dp, "linux,part-probe", &cplen);
-	if (cp == NULL)
+	count = of_property_count_strings(dp, "linux,part-probe");
+	if (count < 0)
 		return part_probe_types_def;
 
-	count = 0;
-	for (l = 0; l != cplen; l++)
-		if (cp[l] == 0)
-			count++;
-
-	res = kzalloc((count + 1)*sizeof(*res), GFP_KERNEL);
+	res = kzalloc((count + 1) * sizeof(*res), GFP_KERNEL);
 	if (!res)
 		return NULL;
-	count = 0;
-	while (cplen > 0) {
-		res[count] = cp;
-		l = strlen(cp) + 1;
-		cp += l;
-		cplen -= l;
-		count++;
-	}
+
+	count = of_property_read_string_array(dp, "linux,part-probe", res,
+					      count);
+	if (count < 0)
+		return NULL;
+
 	return res;
 }
 

drivers/mtd/mtdswap.c

@@ -1235,10 +1235,8 @@ static int mtdswap_show(struct seq_file *s, void *data)
 
 		if (root->rb_node) {
 			count[i] = d->trees[i].count;
-			min[i] = rb_entry(rb_first(root), struct swap_eb,
-					rb)->erase_count;
-			max[i] = rb_entry(rb_last(root), struct swap_eb,
-					rb)->erase_count;
+			min[i] = MTDSWAP_ECNT_MIN(root);
+			max[i] = MTDSWAP_ECNT_MAX(root);
 		} else
 			count[i] = 0;
 	}

drivers/mtd/nand/Kconfig

@@ -13,7 +13,6 @@ config MTD_NAND_ECC_SMC
 menuconfig MTD_NAND
 	tristate "NAND Device Support"
 	depends on MTD
-	select MTD_NAND_IDS
 	select MTD_NAND_ECC
 	help
 	  This enables support for accessing all type of NAND flash
@@ -60,17 +59,6 @@ config MTD_NAND_DENALI_DT
 	  Enable the driver for NAND flash on platforms using a Denali NAND
 	  controller as a DT device.
 
-config MTD_NAND_DENALI_SCRATCH_REG_ADDR
-        hex "Denali NAND size scratch register address"
-        default "0xFF108018"
-        depends on MTD_NAND_DENALI_PCI
-        help
-          Some platforms place the NAND chip size in a scratch register
-          because (some versions of) the driver aren't able to automatically
-          determine the size of certain chips. Set the address of the
-          scratch register here to enable this feature. On Intel Moorestown
-          boards, the scratch register is at 0xFF108018.
-
 config MTD_NAND_GPIO
 	tristate "GPIO assisted NAND Flash driver"
 	depends on GPIOLIB || COMPILE_TEST
@@ -109,9 +97,6 @@ config MTD_NAND_OMAP_BCH
 config MTD_NAND_OMAP_BCH_BUILD
 	def_tristate MTD_NAND_OMAP2 && MTD_NAND_OMAP_BCH
 
-config MTD_NAND_IDS
-	tristate
-
 config MTD_NAND_RICOH
 	tristate "Ricoh xD card reader"
 	default n
@@ -321,11 +306,11 @@ config MTD_NAND_CS553X
 	  If you say "m", the module will be called cs553x_nand.
 
 config MTD_NAND_ATMEL
-	tristate "Support for NAND Flash / SmartMedia on AT91 and AVR32"
-	depends on ARCH_AT91 || AVR32
+	tristate "Support for NAND Flash / SmartMedia on AT91"
+	depends on ARCH_AT91
 	help
 	  Enables support for NAND Flash / Smart Media Card interface
-	  on Atmel AT91 and AVR32 processors.
+	  on Atmel AT91 processors.
 
 config MTD_NAND_PXA3xx
 	tristate "NAND support on PXA3xx and Armada 370/XP"
@@ -443,7 +428,7 @@ config MTD_NAND_FSL_ELBC
 
 config MTD_NAND_FSL_IFC
 	tristate "NAND support for Freescale IFC controller"
-	depends on FSL_SOC || ARCH_LAYERSCAPE
+	depends on FSL_SOC || ARCH_LAYERSCAPE || SOC_LS1021A
 	select FSL_IFC
 	select MEMORY
 	help

drivers/mtd/nand/Makefile

@@ -5,7 +5,6 @@
 obj-$(CONFIG_MTD_NAND)			+= nand.o
 obj-$(CONFIG_MTD_NAND_ECC)		+= nand_ecc.o
 obj-$(CONFIG_MTD_NAND_BCH)		+= nand_bch.o
-obj-$(CONFIG_MTD_NAND_IDS)		+= nand_ids.o
 obj-$(CONFIG_MTD_SM_COMMON) 		+= sm_common.o
 
 obj-$(CONFIG_MTD_NAND_CAFE)		+= cafe_nand.o
@@ -25,7 +24,7 @@ obj-$(CONFIG_MTD_NAND_SHARPSL)		+= sharpsl.o
 obj-$(CONFIG_MTD_NAND_NANDSIM)		+= nandsim.o
 obj-$(CONFIG_MTD_NAND_CS553X)		+= cs553x_nand.o
 obj-$(CONFIG_MTD_NAND_NDFC)		+= ndfc.o
-obj-$(CONFIG_MTD_NAND_ATMEL)		+= atmel_nand.o
+obj-$(CONFIG_MTD_NAND_ATMEL)		+= atmel/
 obj-$(CONFIG_MTD_NAND_GPIO)		+= gpio.o
 omap2_nand-objs := omap2.o
 obj-$(CONFIG_MTD_NAND_OMAP2) 		+= omap2_nand.o
@@ -61,4 +60,10 @@ obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= brcmnand/
 obj-$(CONFIG_MTD_NAND_QCOM)		+= qcom_nandc.o
 obj-$(CONFIG_MTD_NAND_MTK)		+= mtk_nand.o mtk_ecc.o
 
-nand-objs := nand_base.o nand_bbt.o nand_timings.o
+nand-objs := nand_base.o nand_bbt.o nand_timings.o nand_ids.o
+nand-objs += nand_amd.o
+nand-objs += nand_hynix.o
+nand-objs += nand_macronix.o
+nand-objs += nand_micron.o
+nand-objs += nand_samsung.o
+nand-objs += nand_toshiba.o

drivers/mtd/nand/atmel/Makefile

+obj-$(CONFIG_MTD_NAND_ATMEL)	+= atmel-nand-controller.o atmel-pmecc.o
+
+atmel-nand-controller-objs	:= nand-controller.o
+atmel-pmecc-objs		:= pmecc.o

drivers/mtd/nand/atmel/pmecc.h

+/*
+ * © Copyright 2016 ATMEL
+ * © Copyright 2016 Free Electrons
+ *
+ * Author: Boris Brezillon <boris.brezillon@free-electrons.com>
+ *
+ * Derived from the atmel_nand.c driver which contained the following
+ * copyrights:
+ *
+ *    Copyright © 2003 Rick Bronson
+ *
+ *    Derived from drivers/mtd/nand/autcpu12.c
+ *        Copyright © 2001 Thomas Gleixner (gleixner@autronix.de)
+ *
+ *    Derived from drivers/mtd/spia.c
+ *        Copyright © 2000 Steven J. Hill (sjhill@cotw.com)
+ *
+ *
+ *    Add Hardware ECC support for AT91SAM9260 / AT91SAM9263
+ *        Richard Genoud (richard.genoud@gmail.com), Adeneo Copyright © 2007
+ *
+ *        Derived from Das U-Boot source code
+ *              (u-boot-1.1.5/board/atmel/at91sam9263ek/nand.c)
+ *        © Copyright 2006 ATMEL Rousset, Lacressonniere Nicolas
+ *
+ *    Add Programmable Multibit ECC support for various AT91 SoC
+ *        © Copyright 2012 ATMEL, Hong Xu
+ *
+ *    Add Nand Flash Controller support for SAMA5 SoC
+ *        © Copyright 2013 ATMEL, Josh Wu (josh.wu@atmel.com)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef ATMEL_PMECC_H
+#define ATMEL_PMECC_H
+
+#define ATMEL_PMECC_MAXIMIZE_ECC_STRENGTH	0
+#define ATMEL_PMECC_SECTOR_SIZE_AUTO		0
+#define ATMEL_PMECC_OOBOFFSET_AUTO		-1
+
+struct atmel_pmecc_user_req {
+	int pagesize;
+	int oobsize;
+	struct {
+		int strength;
+		int bytes;
+		int sectorsize;
+		int nsectors;
+		int ooboffset;
+	} ecc;
+};
+
+struct atmel_pmecc *devm_atmel_pmecc_get(struct device *dev);
+
+struct atmel_pmecc_user *
+atmel_pmecc_create_user(struct atmel_pmecc *pmecc,
+			struct atmel_pmecc_user_req *req);
+void atmel_pmecc_destroy_user(struct atmel_pmecc_user *user);
+
+int atmel_pmecc_enable(struct atmel_pmecc_user *user, int op);
+void atmel_pmecc_disable(struct atmel_pmecc_user *user);
+int atmel_pmecc_wait_rdy(struct atmel_pmecc_user *user);
+int atmel_pmecc_correct_sector(struct atmel_pmecc_user *user, int sector,
+			       void *data, void *ecc);
+bool atmel_pmecc_correct_erased_chunks(struct atmel_pmecc_user *user);
+void atmel_pmecc_get_generated_eccbytes(struct atmel_pmecc_user *user,
+					int sector, void *ecc);
+
+#endif /* ATMEL_PMECC_H */

drivers/mtd/nand/atmel_nand_ecc.h

-/*
- * Error Corrected Code Controller (ECC) - System peripherals regsters.
- * Based on AT91SAM9260 datasheet revision B.
- *
- * Copyright (C) 2007 Andrew Victor
- * Copyright (C) 2007 - 2012 Atmel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#ifndef ATMEL_NAND_ECC_H
-#define ATMEL_NAND_ECC_H
-
-#define ATMEL_ECC_CR		0x00			/* Control register */
-#define		ATMEL_ECC_RST		(1 << 0)		/* Reset parity */
-
-#define ATMEL_ECC_MR		0x04			/* Mode register */
-#define		ATMEL_ECC_PAGESIZE	(3 << 0)		/* Page Size */
-#define			ATMEL_ECC_PAGESIZE_528		(0)
-#define			ATMEL_ECC_PAGESIZE_1056		(1)
-#define			ATMEL_ECC_PAGESIZE_2112		(2)
-#define			ATMEL_ECC_PAGESIZE_4224		(3)
-
-#define ATMEL_ECC_SR		0x08			/* Status register */
-#define		ATMEL_ECC_RECERR		(1 << 0)		/* Recoverable Error */
-#define		ATMEL_ECC_ECCERR		(1 << 1)		/* ECC Single Bit Error */
-#define		ATMEL_ECC_MULERR		(1 << 2)		/* Multiple Errors */
-
-#define ATMEL_ECC_PR		0x0c			/* Parity register */
-#define		ATMEL_ECC_BITADDR	(0xf << 0)		/* Bit Error Address */
-#define		ATMEL_ECC_WORDADDR	(0xfff << 4)		/* Word Error Address */
-
-#define ATMEL_ECC_NPR		0x10			/* NParity register */
-#define		ATMEL_ECC_NPARITY	(0xffff << 0)		/* NParity */
-
-/* PMECC Register Definitions */
-#define ATMEL_PMECC_CFG			0x000	/* Configuration Register */
-#define		PMECC_CFG_BCH_ERR2		(0 << 0)
-#define		PMECC_CFG_BCH_ERR4		(1 << 0)
-#define		PMECC_CFG_BCH_ERR8		(2 << 0)
-#define		PMECC_CFG_BCH_ERR12		(3 << 0)
-#define		PMECC_CFG_BCH_ERR24		(4 << 0)
-#define		PMECC_CFG_BCH_ERR32		(5 << 0)
-
-#define		PMECC_CFG_SECTOR512		(0 << 4)
-#define		PMECC_CFG_SECTOR1024		(1 << 4)
-
-#define		PMECC_CFG_PAGE_1SECTOR		(0 << 8)
-#define		PMECC_CFG_PAGE_2SECTORS		(1 << 8)
-#define		PMECC_CFG_PAGE_4SECTORS		(2 << 8)
-#define		PMECC_CFG_PAGE_8SECTORS		(3 << 8)
-
-#define		PMECC_CFG_READ_OP		(0 << 12)
-#define		PMECC_CFG_WRITE_OP		(1 << 12)
-
-#define		PMECC_CFG_SPARE_ENABLE		(1 << 16)
-#define		PMECC_CFG_SPARE_DISABLE		(0 << 16)
-
-#define		PMECC_CFG_AUTO_ENABLE		(1 << 20)
-#define		PMECC_CFG_AUTO_DISABLE		(0 << 20)
-
-#define ATMEL_PMECC_SAREA		0x004	/* Spare area size */
-#define ATMEL_PMECC_SADDR		0x008	/* PMECC starting address */
-#define ATMEL_PMECC_EADDR		0x00c	/* PMECC ending address */
-#define ATMEL_PMECC_CLK			0x010	/* PMECC clock control */
-#define		PMECC_CLK_133MHZ		(2 << 0)
-
-#define ATMEL_PMECC_CTRL		0x014	/* PMECC control register */
-#define		PMECC_CTRL_RST			(1 << 0)
-#define		PMECC_CTRL_DATA			(1 << 1)
-#define		PMECC_CTRL_USER			(1 << 2)
-#define		PMECC_CTRL_ENABLE		(1 << 4)
-#define		PMECC_CTRL_DISABLE		(1 << 5)
-
-#define ATMEL_PMECC_SR			0x018	/* PMECC status register */
-#define		PMECC_SR_BUSY			(1 << 0)
-#define		PMECC_SR_ENABLE			(1 << 4)
-
-#define ATMEL_PMECC_IER			0x01c	/* PMECC interrupt enable */
-#define		PMECC_IER_ENABLE		(1 << 0)
-#define ATMEL_PMECC_IDR			0x020	/* PMECC interrupt disable */
-#define		PMECC_IER_DISABLE		(1 << 0)
-#define ATMEL_PMECC_IMR			0x024	/* PMECC interrupt mask */
-#define		PMECC_IER_MASK			(1 << 0)
-#define ATMEL_PMECC_ISR			0x028	/* PMECC interrupt status */
-#define ATMEL_PMECC_ECCx		0x040	/* PMECC ECC x */
-#define ATMEL_PMECC_REMx		0x240	/* PMECC REM x */
-
-/* PMERRLOC Register Definitions */
-#define ATMEL_PMERRLOC_ELCFG		0x000	/* Error location config */
-#define		PMERRLOC_ELCFG_SECTOR_512	(0 << 0)
-#define		PMERRLOC_ELCFG_SECTOR_1024	(1 << 0)
-#define		PMERRLOC_ELCFG_NUM_ERRORS(n)	((n) << 16)
-
-#define ATMEL_PMERRLOC_ELPRIM		0x004	/* Error location primitive */
-#define ATMEL_PMERRLOC_ELEN		0x008	/* Error location enable */
-#define ATMEL_PMERRLOC_ELDIS		0x00c	/* Error location disable */
-#define		PMERRLOC_DISABLE		(1 << 0)
-
-#define ATMEL_PMERRLOC_ELSR		0x010	/* Error location status */
-#define		PMERRLOC_ELSR_BUSY		(1 << 0)
-#define ATMEL_PMERRLOC_ELIER		0x014	/* Error location int enable */
-#define ATMEL_PMERRLOC_ELIDR		0x018	/* Error location int disable */
-#define ATMEL_PMERRLOC_ELIMR		0x01c	/* Error location int mask */
-#define ATMEL_PMERRLOC_ELISR		0x020	/* Error location int status */
-#define		PMERRLOC_ERR_NUM_MASK		(0x1f << 8)
-#define		PMERRLOC_CALC_DONE		(1 << 0)
-#define ATMEL_PMERRLOC_SIGMAx		0x028	/* Error location SIGMA x */
-
-/*
- * The ATMEL_PMERRLOC_ELx register location depends from the number of
- * bits corrected by the PMECC controller. Do not use it.
- */
-
-/* Register access macros for PMECC */
-#define pmecc_readl_relaxed(addr, reg) \
-	readl_relaxed((addr) + ATMEL_PMECC_##reg)
-
-#define pmecc_writel(addr, reg, value) \
-	writel((value), (addr) + ATMEL_PMECC_##reg)
-
-#define pmecc_readb_ecc_relaxed(addr, sector, n) \
-	readb_relaxed((addr) + ATMEL_PMECC_ECCx + ((sector) * 0x40) + (n))
-
-#define pmecc_readl_rem_relaxed(addr, sector, n) \
-	readl_relaxed((addr) + ATMEL_PMECC_REMx + ((sector) * 0x40) + ((n) * 4))
-
-#define pmerrloc_readl_relaxed(addr, reg) \
-	readl_relaxed((addr) + ATMEL_PMERRLOC_##reg)
-
-#define pmerrloc_writel(addr, reg, value) \
-	writel((value), (addr) + ATMEL_PMERRLOC_##reg)
-
-#define pmerrloc_writel_sigma_relaxed(addr, n, value) \
-	writel_relaxed((value), (addr) + ATMEL_PMERRLOC_SIGMAx + ((n) * 4))
-
-#define pmerrloc_readl_sigma_relaxed(addr, n) \
-	readl_relaxed((addr) + ATMEL_PMERRLOC_SIGMAx + ((n) * 4))
-
-#define pmerrloc_readl_el_relaxed(addr, n) \
-	readl_relaxed((addr) + ((n) * 4))
-
-/* Galois field dimension */
-#define PMECC_GF_DIMENSION_13			13
-#define PMECC_GF_DIMENSION_14			14
-
-/* Primitive Polynomial used by PMECC */
-#define PMECC_GF_13_PRIMITIVE_POLY		0x201b
-#define PMECC_GF_14_PRIMITIVE_POLY		0x4443
-
-#define PMECC_LOOKUP_TABLE_SIZE_512		0x2000
-#define PMECC_LOOKUP_TABLE_SIZE_1024		0x4000
-
-/* Time out value for reading PMECC status register */
-#define PMECC_MAX_TIMEOUT_MS			100
-
-/* Reserved bytes in oob area */
-#define PMECC_OOB_RESERVED_BYTES		2
-
-#endif

drivers/mtd/nand/atmel_nand_nfc.h

-/*
- * Atmel Nand Flash Controller (NFC) - System peripherals regsters.
- * Based on SAMA5D3 datasheet.
- *
- * © Copyright 2013 Atmel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#ifndef ATMEL_NAND_NFC_H
-#define ATMEL_NAND_NFC_H
-
-/*
- * HSMC NFC registers
- */
-#define ATMEL_HSMC_NFC_CFG	0x00		/* NFC Configuration Register */
-#define		NFC_CFG_PAGESIZE	(7 << 0)
-#define			NFC_CFG_PAGESIZE_512	(0 << 0)
-#define			NFC_CFG_PAGESIZE_1024	(1 << 0)
-#define			NFC_CFG_PAGESIZE_2048	(2 << 0)
-#define			NFC_CFG_PAGESIZE_4096	(3 << 0)
-#define			NFC_CFG_PAGESIZE_8192	(4 << 0)
-#define		NFC_CFG_WSPARE		(1 << 8)
-#define		NFC_CFG_RSPARE		(1 << 9)
-#define		NFC_CFG_NFC_DTOCYC	(0xf << 16)
-#define		NFC_CFG_NFC_DTOMUL	(0x7 << 20)
-#define		NFC_CFG_NFC_SPARESIZE	(0x7f << 24)
-#define		NFC_CFG_NFC_SPARESIZE_BIT_POS	24
-
-#define ATMEL_HSMC_NFC_CTRL	0x04		/* NFC Control Register */
-#define		NFC_CTRL_ENABLE		(1 << 0)
-#define		NFC_CTRL_DISABLE	(1 << 1)
-
-#define ATMEL_HSMC_NFC_SR	0x08		/* NFC Status Register */
-#define		NFC_SR_BUSY		(1 << 8)
-#define		NFC_SR_XFR_DONE		(1 << 16)
-#define		NFC_SR_CMD_DONE		(1 << 17)
-#define		NFC_SR_DTOE		(1 << 20)
-#define		NFC_SR_UNDEF		(1 << 21)
-#define		NFC_SR_AWB		(1 << 22)
-#define		NFC_SR_ASE		(1 << 23)
-#define		NFC_SR_RB_EDGE		(1 << 24)
-
-#define ATMEL_HSMC_NFC_IER	0x0c
-#define ATMEL_HSMC_NFC_IDR	0x10
-#define ATMEL_HSMC_NFC_IMR	0x14
-#define ATMEL_HSMC_NFC_CYCLE0	0x18		/* NFC Address Cycle Zero */
-#define		ATMEL_HSMC_NFC_ADDR_CYCLE0	(0xff)
-
-#define ATMEL_HSMC_NFC_BANK	0x1c		/* NFC Bank Register */
-#define		ATMEL_HSMC_NFC_BANK0		(0 << 0)
-#define		ATMEL_HSMC_NFC_BANK1		(1 << 0)
-
-#define nfc_writel(addr, reg, value) \
-	writel((value), (addr) + ATMEL_HSMC_NFC_##reg)
-
-#define nfc_readl(addr, reg) \
-	readl_relaxed((addr) + ATMEL_HSMC_NFC_##reg)
-
-/*
- * NFC Address Command definitions
- */
-#define NFCADDR_CMD_CMD1	(0xff << 2)	/* Command for Cycle 1 */
-#define NFCADDR_CMD_CMD1_BIT_POS	2
-#define NFCADDR_CMD_CMD2	(0xff << 10)	/* Command for Cycle 2 */
-#define NFCADDR_CMD_CMD2_BIT_POS	10
-#define NFCADDR_CMD_VCMD2	(0x1 << 18)	/* Valid Cycle 2 Command */
-#define NFCADDR_CMD_ACYCLE	(0x7 << 19)	/* Number of Address required */
-#define		NFCADDR_CMD_ACYCLE_NONE		(0x0 << 19)
-#define		NFCADDR_CMD_ACYCLE_1		(0x1 << 19)
-#define		NFCADDR_CMD_ACYCLE_2		(0x2 << 19)
-#define		NFCADDR_CMD_ACYCLE_3		(0x3 << 19)
-#define		NFCADDR_CMD_ACYCLE_4		(0x4 << 19)
-#define		NFCADDR_CMD_ACYCLE_5		(0x5 << 19)
-#define NFCADDR_CMD_ACYCLE_BIT_POS	19
-#define NFCADDR_CMD_CSID	(0x7 << 22)	/* Chip Select Identifier */
-#define		NFCADDR_CMD_CSID_0		(0x0 << 22)
-#define		NFCADDR_CMD_CSID_1		(0x1 << 22)
-#define		NFCADDR_CMD_CSID_2		(0x2 << 22)
-#define		NFCADDR_CMD_CSID_3		(0x3 << 22)
-#define		NFCADDR_CMD_CSID_4		(0x4 << 22)
-#define		NFCADDR_CMD_CSID_5		(0x5 << 22)
-#define		NFCADDR_CMD_CSID_6		(0x6 << 22)
-#define		NFCADDR_CMD_CSID_7		(0x7 << 22)
-#define NFCADDR_CMD_DATAEN	(0x1 << 25)	/* Data Transfer Enable */
-#define NFCADDR_CMD_DATADIS	(0x0 << 25)	/* Data Transfer Disable */
-#define NFCADDR_CMD_NFCRD	(0x0 << 26)	/* NFC Read Enable */
-#define NFCADDR_CMD_NFCWR	(0x1 << 26)	/* NFC Write Enable */
-#define NFCADDR_CMD_NFCBUSY	(0x1 << 27)	/* NFC Busy */
-
-#define nfc_cmd_addr1234_writel(cmd, addr1234, nfc_base) \
-	writel((addr1234), (cmd) + nfc_base)
-
-#define nfc_cmd_readl(bitstatus, nfc_base) \
-	readl_relaxed((bitstatus) + nfc_base)
-
-#define NFC_TIME_OUT_MS		100
-#define	NFC_SRAM_BANK1_OFFSET	0x1200
-
-#endif

drivers/mtd/nand/brcmnand/brcmnand.c

@@ -101,6 +101,9 @@ struct brcm_nand_dma_desc {
 #define BRCMNAND_MIN_BLOCKSIZE	(8 * 1024)
 #define BRCMNAND_MIN_DEVSIZE	(4ULL * 1024 * 1024)
 
+#define NAND_CTRL_RDY			(INTFC_CTLR_READY | INTFC_FLASH_READY)
+#define NAND_POLL_STATUS_TIMEOUT_MS	100
+
 /* Controller feature flags */
 enum {
 	BRCMNAND_HAS_1K_SECTORS			= BIT(0),
@@ -765,6 +768,31 @@ enum {
 	CS_SELECT_AUTO_DEVICE_ID_CFG		= BIT(30),
 };
 
+static int bcmnand_ctrl_poll_status(struct brcmnand_controller *ctrl,
+				    u32 mask, u32 expected_val,
+				    unsigned long timeout_ms)
+{
+	unsigned long limit;
+	u32 val;
+
+	if (!timeout_ms)
+		timeout_ms = NAND_POLL_STATUS_TIMEOUT_MS;
+
+	limit = jiffies + msecs_to_jiffies(timeout_ms);
+	do {
+		val = brcmnand_read_reg(ctrl, BRCMNAND_INTFC_STATUS);
+		if ((val & mask) == expected_val)
+			return 0;
+
+		cpu_relax();
+	} while (time_after(limit, jiffies));
+
+	dev_warn(ctrl->dev, "timeout on status poll (expected %x got %x)\n",
+		 expected_val, val & mask);
+
+	return -ETIMEDOUT;
+}
+
 static inline void brcmnand_set_wp(struct brcmnand_controller *ctrl, bool en)
 {
 	u32 val = en ? CS_SELECT_NAND_WP : 0;
@@ -1024,12 +1052,39 @@ static void brcmnand_wp(struct mtd_info *mtd, int wp)
 
 	if ((ctrl->features & BRCMNAND_HAS_WP) && wp_on == 1) {
 		static int old_wp = -1;
+		int ret;
 
 		if (old_wp != wp) {
 			dev_dbg(ctrl->dev, "WP %s\n", wp ? "on" : "off");
 			old_wp = wp;
 		}
+
+		/*
+		 * make sure ctrl/flash ready before and after
+		 * changing state of #WP pin
+		 */
+		ret = bcmnand_ctrl_poll_status(ctrl, NAND_CTRL_RDY |
+					       NAND_STATUS_READY,
+					       NAND_CTRL_RDY |
+					       NAND_STATUS_READY, 0);
+		if (ret)
+			return;
+
 		brcmnand_set_wp(ctrl, wp);
+		chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1);
+		/* NAND_STATUS_WP 0x00 = protected, 0x80 = not protected */
+		ret = bcmnand_ctrl_poll_status(ctrl,
+					       NAND_CTRL_RDY |
+					       NAND_STATUS_READY |
+					       NAND_STATUS_WP,
+					       NAND_CTRL_RDY |
+					       NAND_STATUS_READY |
+					       (wp ? 0 : NAND_STATUS_WP), 0);
+
+		if (ret)
+			dev_err_ratelimited(&host->pdev->dev,
+					    "nand #WP expected %s\n",
+					    wp ? "on" : "off");
 	}
 }
 
@@ -1157,15 +1212,15 @@ static irqreturn_t brcmnand_dma_irq(int irq, void *data)
 static void brcmnand_send_cmd(struct brcmnand_host *host, int cmd)
 {
 	struct brcmnand_controller *ctrl = host->ctrl;
-	u32 intfc;
+	int ret;
 
 	dev_dbg(ctrl->dev, "send native cmd %d addr_lo 0x%x\n", cmd,
 		brcmnand_read_reg(ctrl, BRCMNAND_CMD_ADDRESS));
 	BUG_ON(ctrl->cmd_pending != 0);
 	ctrl->cmd_pending = cmd;
 
-	intfc = brcmnand_read_reg(ctrl, BRCMNAND_INTFC_STATUS);
-	WARN_ON(!(intfc & INTFC_CTLR_READY));
+	ret = bcmnand_ctrl_poll_status(ctrl, NAND_CTRL_RDY, NAND_CTRL_RDY, 0);
+	WARN_ON(ret);
 
 	mb(); /* flush previous writes */
 	brcmnand_write_reg(ctrl, BRCMNAND_CMD_START,

drivers/mtd/nand/cmx270_nand.c

@@ -145,7 +145,7 @@ static int __init cmx270_init(void)
 
 	ret = gpio_request(GPIO_NAND_CS, "NAND CS");
 	if (ret) {
-		pr_warning("CM-X270: failed to request NAND CS gpio\n");
+		pr_warn("CM-X270: failed to request NAND CS gpio\n");
 		return ret;
 	}
 
@@ -153,7 +153,7 @@ static int __init cmx270_init(void)
 
 	ret = gpio_request(GPIO_NAND_RB, "NAND R/B");
 	if (ret) {
-		pr_warning("CM-X270: failed to request NAND R/B gpio\n");
+		pr_warn("CM-X270: failed to request NAND R/B gpio\n");
 		goto err_gpio_request;
 	}
 

drivers/mtd/nand/davinci_nand.c

@@ -581,6 +581,17 @@ static struct davinci_nand_pdata
 			"ti,davinci-nand-use-bbt"))
 			pdata->bbt_options = NAND_BBT_USE_FLASH;
 
+		/*
+		 * Since kernel v4.8, this driver has been fixed to enable
+		 * use of 4-bit hardware ECC with subpages and verified on
+		 * TI's keystone EVMs (K2L, K2HK and K2E).
+		 * However, in the interest of not breaking systems using
+		 * existing UBI partitions, sub-page writes are not being
+		 * (re)enabled. If you want to use subpage writes on Keystone
+		 * platforms (i.e. do not have any existing UBI partitions),
+		 * then use "ti,davinci-nand" as the compatible in your
+		 * device-tree file.
+		 */
 		if (of_device_is_compatible(pdev->dev.of_node,
 					    "ti,keystone-nand")) {
 			pdata->options |= NAND_NO_SUBPAGE_WRITE;

drivers/mtd/nand/gpio.c

@@ -78,7 +78,9 @@ static void gpio_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
 	gpio_nand_dosync(gpiomtd);
 
 	if (ctrl & NAND_CTRL_CHANGE) {
-		gpio_set_value(gpiomtd->plat.gpio_nce, !(ctrl & NAND_NCE));
+		if (gpio_is_valid(gpiomtd->plat.gpio_nce))
+			gpio_set_value(gpiomtd->plat.gpio_nce,
+				       !(ctrl & NAND_NCE));
 		gpio_set_value(gpiomtd->plat.gpio_cle, !!(ctrl & NAND_CLE));
 		gpio_set_value(gpiomtd->plat.gpio_ale, !!(ctrl & NAND_ALE));
 		gpio_nand_dosync(gpiomtd);
@@ -201,6 +203,7 @@ static int gpio_nand_remove(struct platform_device *pdev)
 
 	if (gpio_is_valid(gpiomtd->plat.gpio_nwp))
 		gpio_set_value(gpiomtd->plat.gpio_nwp, 0);
+	if (gpio_is_valid(gpiomtd->plat.gpio_nce))
 		gpio_set_value(gpiomtd->plat.gpio_nce, 1);
 
 	return 0;
@@ -239,10 +242,13 @@ static int gpio_nand_probe(struct platform_device *pdev)
 	if (ret)
 		return ret;
 
-	ret = devm_gpio_request(&pdev->dev, gpiomtd->plat.gpio_nce, "NAND NCE");
+	if (gpio_is_valid(gpiomtd->plat.gpio_nce)) {
+		ret = devm_gpio_request(&pdev->dev, gpiomtd->plat.gpio_nce,
+					"NAND NCE");
 		if (ret)
 			return ret;
 		gpio_direction_output(gpiomtd->plat.gpio_nce, 1);
+	}
 
 	if (gpio_is_valid(gpiomtd->plat.gpio_nwp)) {
 		ret = devm_gpio_request(&pdev->dev, gpiomtd->plat.gpio_nwp,

drivers/mtd/nand/nand_macronix.c

+/*
+ * Copyright (C) 2017 Free Electrons
+ * Copyright (C) 2017 NextThing Co
+ *
+ * Author: Boris Brezillon <boris.brezillon@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/mtd/nand.h>
+
+static int macronix_nand_init(struct nand_chip *chip)
+{
+	if (nand_is_slc(chip))
+		chip->bbt_options |= NAND_BBT_SCAN2NDPAGE;
+
+	return 0;
+}
+
+const struct nand_manufacturer_ops macronix_nand_manuf_ops = {
+	.init = macronix_nand_init,
+};

drivers/mtd/nand/nandsim.c

@@ -902,7 +902,7 @@ static int parse_weakpages(void)
 		zero_ok = (*w == '0' ? 1 : 0);
 		page_no = simple_strtoul(w, &w, 0);
 		if (!zero_ok && !page_no) {
-			NS_ERR("invalid weakpagess.\n");
+			NS_ERR("invalid weakpages.\n");
 			return -EINVAL;
 		}
 		max_writes = 3;

drivers/mtd/spi-nor/Makefile

@@ -8,3 +8,4 @@ obj-$(CONFIG_MTD_MT81xx_NOR)    += mtk-quadspi.o
 obj-$(CONFIG_SPI_NXP_SPIFI)	+= nxp-spifi.o
 obj-$(CONFIG_SPI_INTEL_SPI)	+= intel-spi.o
 obj-$(CONFIG_SPI_INTEL_SPI_PLATFORM)	+= intel-spi-platform.o
+obj-$(CONFIG_SPI_STM32_QUADSPI)	+= stm32-quadspi.o
\ No newline at end of file