提交 8ed57590 编写于 作者: L Linus Torvalds
......@@ -2247,6 +2247,12 @@ S: 249 Nichols Avenue
S: Syracuse, New York 13206
S: USA
N: Kyle McMartin
E: kyle@parisc-linux.org
D: Linux/PARISC hacker
D: AD1889 sound driver
S: Ottawa, Canada
N: Dirk Melchers
E: dirk@merlin.nbg.sub.org
D: 8 bit XT hard disk driver for OMTI5520
......
......@@ -197,6 +197,15 @@ M: Thorsten Knabe <linux@thorsten-knabe.de>
W: http://linux.thorsten-knabe.de
S: Maintained
AD1889 SOUND DRIVER
P: Kyle McMartin
M: kyle@parisc-linux.org
P: Thibaut Varene
M: T-Bone@parisc-linux.org
W: http://wiki.parisc-linux.org/AD1889
L: parisc-linux@lists.parisc-linux.org
S: Maintained
ADM1025 HARDWARE MONITOR DRIVER
P: Jean Delvare
M: khali@linux-fr.org
......
......@@ -47,10 +47,10 @@ config PM
config ISA_DMA_API
bool
default y
config ARCH_MAY_HAVE_PC_FDC
bool
depends on BROKEN
default y
source "init/Kconfig"
......@@ -154,13 +154,14 @@ config HOTPLUG_CPU
config ARCH_DISCONTIGMEM_ENABLE
bool "Discontiguous memory support (EXPERIMENTAL)"
depends on EXPERIMENTAL
depends on 64BIT && EXPERIMENTAL
help
Say Y to support efficient handling of discontiguous physical memory,
for architectures which are either NUMA (Non-Uniform Memory Access)
or have huge holes in the physical address space for other reasons.
See <file:Documentation/vm/numa> for more.
source "kernel/Kconfig.hz"
source "mm/Kconfig"
config PREEMPT
......
......@@ -20,7 +20,8 @@ NM = sh $(srctree)/arch/parisc/nm
CHECKFLAGS += -D__hppa__=1
ifdef CONFIG_64BIT
CROSS_COMPILE := hppa64-linux-
CROSS_COMPILE := $(shell if [ -x /usr/bin/hppa64-linux-gnu-gcc ]; then \
echo hppa64-linux-gnu-; else echo hppa64-linux-; fi)
UTS_MACHINE := parisc64
CHECKFLAGS += -D__LP64__=1 -m64
else
......@@ -34,6 +35,14 @@ FINAL_LD=$(CROSS_COMPILE)ld --warn-common --warn-section-align
OBJCOPY_FLAGS =-O binary -R .note -R .comment -S
GCC_VERSION := $(call cc-version)
ifneq ($(shell if [ -z $(GCC_VERSION) ] ; then echo "bad"; fi ;),)
$(error Sorry, couldn't find ($(cc-version)).)
endif
ifneq ($(shell if [ $(GCC_VERSION) -lt 0303 ] ; then echo "bad"; fi ;),)
$(error Sorry, your compiler is too old ($(GCC_VERSION)). GCC v3.3 or above is required.)
endif
cflags-y := -pipe
# These flags should be implied by an hppa-linux configuration, but they
......@@ -43,7 +52,7 @@ cflags-y += -mno-space-regs -mfast-indirect-calls
# Currently we save and restore fpregs on all kernel entry/interruption paths.
# If that gets optimized, we might need to disable the use of fpregs in the
# kernel.
#cflags-y += -mdisable-fpregs
cflags-y += -mdisable-fpregs
# Without this, "ld -r" results in .text sections that are too big
# (> 0x40000) for branches to reach stubs.
......
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.10-pa5
# Wed Jan 5 13:20:32 2005
# Linux kernel version: 2.6.14-rc5-pa1
# Fri Oct 21 23:04:34 2005
#
CONFIG_PARISC=y
CONFIG_MMU=y
CONFIG_STACK_GROWSUP=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
#
# Code maturity level options
......@@ -15,35 +19,40 @@ CONFIG_EXPERIMENTAL=y
# CONFIG_CLEAN_COMPILE is not set
CONFIG_BROKEN=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
#
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
CONFIG_LOG_BUF_SHIFT=16
CONFIG_HOTPLUG=y
CONFIG_KOBJECT_UEVENT=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
#
# Loadable module support
......@@ -65,9 +74,18 @@ CONFIG_PA7100LC=y
# CONFIG_PA7300LC is not set
# CONFIG_PA8X00 is not set
CONFIG_PA11=y
# CONFIG_64BIT is not set
# CONFIG_SMP is not set
# CONFIG_DISCONTIGMEM is not set
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
# CONFIG_PREEMPT is not set
# CONFIG_HPUX is not set
......@@ -81,8 +99,6 @@ CONFIG_GSC_LASI=y
# CONFIG_GSC_WAX is not set
# CONFIG_EISA is not set
# CONFIG_PCI is not set
CONFIG_CHASSIS_LCD_LED=y
# CONFIG_PDC_CHASSIS is not set
#
# PCCARD (PCMCIA/CardBus) support
......@@ -90,12 +106,15 @@ CONFIG_CHASSIS_LCD_LED=y
# CONFIG_PCCARD is not set
#
# PC-card bridges
# PCI Hotplug Support
#
#
# PCI Hotplug Support
# PA-RISC specific drivers
#
CONFIG_CHASSIS_LCD_LED=y
# CONFIG_PDC_CHASSIS is not set
CONFIG_PDC_STABLE=y
#
# Executable file formats
......@@ -104,137 +123,7 @@ CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=m
#
# Device Drivers
#
#
# Generic Driver Options
#
# CONFIG_STANDALONE is not set
# CONFIG_PREVENT_FIRMWARE_BUILD is not set
CONFIG_FW_LOADER=y
# CONFIG_DEBUG_DRIVER is not set
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
CONFIG_PARPORT=y
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_PC_CML1=m
# CONFIG_PARPORT_PC_FIFO is not set
# CONFIG_PARPORT_PC_SUPERIO is not set
CONFIG_PARPORT_GSC=y
# CONFIG_PARPORT_OTHER is not set
# CONFIG_PARPORT_1284 is not set
#
# Plug and Play support
#
#
# Block devices
#
# CONFIG_BLK_DEV_FD is not set
# CONFIG_PARIDE is not set
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=y
# CONFIG_BLK_DEV_NBD is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=6144
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_CDROM_PKTCDVD is not set
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
#
# ATA/ATAPI/MFM/RLL support
#
# CONFIG_IDE is not set
#
# SCSI device support
#
CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_ST=y
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=y
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=y
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
#
# SCSI Transport Attributes
#
CONFIG_SCSI_SPI_ATTRS=y
# CONFIG_SCSI_FC_ATTRS is not set
#
# SCSI low-level drivers
#
# CONFIG_SCSI_SATA is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
CONFIG_SCSI_LASI700=y
CONFIG_53C700_MEM_MAPPED=y
CONFIG_53C700_LE_ON_BE=y
# CONFIG_SCSI_ZALON is not set
CONFIG_SCSI_DEBUG=m
#
# Multi-device support (RAID and LVM)
#
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
CONFIG_MD_RAID1=m
# CONFIG_MD_RAID10 is not set
# CONFIG_MD_RAID5 is not set
# CONFIG_MD_RAID6 is not set
# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
# CONFIG_BLK_DEV_DM is not set
#
# Fusion MPT device support
#
#
# IEEE 1394 (FireWire) support
#
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
#
# Networking support
# Networking
#
CONFIG_NET=y
......@@ -243,12 +132,14 @@ CONFIG_NET=y
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_NETLINK_DEV=y
CONFIG_UNIX=y
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
CONFIG_NET_KEY=m
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
......@@ -262,8 +153,10 @@ CONFIG_INET_AH=m
CONFIG_INET_ESP=m
# CONFIG_INET_IPCOMP is not set
CONFIG_INET_TUNNEL=m
CONFIG_IP_TCPDIAG=y
# CONFIG_IP_TCPDIAG_IPV6 is not set
CONFIG_INET_DIAG=m
CONFIG_INET_TCP_DIAG=m
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_BIC=y
#
# IP: Virtual Server Configuration
......@@ -272,6 +165,7 @@ CONFIG_IP_TCPDIAG=y
# CONFIG_IPV6 is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
# CONFIG_NETFILTER_NETLINK is not set
#
# IP: Netfilter Configuration
......@@ -279,11 +173,14 @@ CONFIG_NETFILTER=y
CONFIG_IP_NF_CONNTRACK=m
# CONFIG_IP_NF_CT_ACCT is not set
CONFIG_IP_NF_CONNTRACK_MARK=y
# CONFIG_IP_NF_CONNTRACK_EVENTS is not set
CONFIG_IP_NF_CT_PROTO_SCTP=m
CONFIG_IP_NF_FTP=m
CONFIG_IP_NF_IRC=m
# CONFIG_IP_NF_NETBIOS_NS is not set
CONFIG_IP_NF_TFTP=m
CONFIG_IP_NF_AMANDA=m
# CONFIG_IP_NF_PPTP is not set
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_LIMIT=m
......@@ -307,21 +204,23 @@ CONFIG_IP_NF_MATCH_OWNER=m
# CONFIG_IP_NF_MATCH_ADDRTYPE is not set
# CONFIG_IP_NF_MATCH_REALM is not set
CONFIG_IP_NF_MATCH_SCTP=m
# CONFIG_IP_NF_MATCH_DCCP is not set
CONFIG_IP_NF_MATCH_COMMENT=m
CONFIG_IP_NF_MATCH_CONNMARK=m
CONFIG_IP_NF_MATCH_HASHLIMIT=m
# CONFIG_IP_NF_MATCH_STRING is not set
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
# CONFIG_IP_NF_TARGET_NFQUEUE is not set
CONFIG_IP_NF_NAT=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_SAME=m
# CONFIG_IP_NF_NAT_LOCAL is not set
CONFIG_IP_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_NAT_IRC=m
CONFIG_IP_NF_NAT_FTP=m
......@@ -333,6 +232,7 @@ CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_DSCP=m
CONFIG_IP_NF_TARGET_MARK=m
CONFIG_IP_NF_TARGET_CLASSIFY=m
# CONFIG_IP_NF_TARGET_TTL is not set
CONFIG_IP_NF_TARGET_CONNMARK=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_RAW=m
......@@ -340,10 +240,11 @@ CONFIG_IP_NF_TARGET_NOTRACK=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
# CONFIG_IP_NF_COMPAT_IPCHAINS is not set
# CONFIG_IP_NF_COMPAT_IPFWADM is not set
CONFIG_XFRM=y
CONFIG_XFRM_USER=m
#
# DCCP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_DCCP is not set
#
# SCTP Configuration (EXPERIMENTAL)
......@@ -362,10 +263,6 @@ CONFIG_LLC2=m
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
# CONFIG_NET_CLS_ROUTE is not set
......@@ -373,17 +270,162 @@ CONFIG_LLC2=m
# Network testing
#
CONFIG_NET_PKTGEN=m
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_IEEE80211 is not set
#
# Device Drivers
#
#
# Generic Driver Options
#
# CONFIG_STANDALONE is not set
# CONFIG_PREVENT_FIRMWARE_BUILD is not set
CONFIG_FW_LOADER=y
# CONFIG_DEBUG_DRIVER is not set
#
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
CONFIG_PARPORT=y
CONFIG_PARPORT_PC=m
# CONFIG_PARPORT_PC_FIFO is not set
# CONFIG_PARPORT_PC_SUPERIO is not set
CONFIG_PARPORT_GSC=y
# CONFIG_PARPORT_1284 is not set
#
# Plug and Play support
#
#
# Block devices
#
# CONFIG_BLK_DEV_FD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=y
# CONFIG_BLK_DEV_NBD is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=6144
CONFIG_BLK_DEV_INITRD=y
# CONFIG_CDROM_PKTCDVD is not set
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
CONFIG_ATA_OVER_ETH=m
#
# ATA/ATAPI/MFM/RLL support
#
# CONFIG_IDE is not set
#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_ST=y
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=y
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=y
# CONFIG_CHR_DEV_SCH is not set
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
#
# SCSI Transport Attributes
#
CONFIG_SCSI_SPI_ATTRS=y
# CONFIG_SCSI_FC_ATTRS is not set
CONFIG_SCSI_ISCSI_ATTRS=m
# CONFIG_SCSI_SAS_ATTRS is not set
#
# SCSI low-level drivers
#
# CONFIG_SCSI_SATA is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
CONFIG_SCSI_LASI700=y
CONFIG_53C700_LE_ON_BE=y
# CONFIG_SCSI_ZALON is not set
CONFIG_SCSI_DEBUG=m
#
# Multi-device support (RAID and LVM)
#
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
CONFIG_MD_RAID1=m
# CONFIG_MD_RAID10 is not set
# CONFIG_MD_RAID5 is not set
# CONFIG_MD_RAID6 is not set
# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
# CONFIG_BLK_DEV_DM is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
#
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
#
# Network device support
#
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
CONFIG_BONDING=m
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
# CONFIG_ETHERTAP is not set
#
# PHY device support
#
# CONFIG_PHYLIB is not set
#
# Ethernet (10 or 100Mbit)
......@@ -391,6 +433,7 @@ CONFIG_TUN=m
CONFIG_NET_ETHERNET=y
CONFIG_MII=m
CONFIG_LASI_82596=y
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
......@@ -414,6 +457,7 @@ CONFIG_NET_RADIO=y
#
# CONFIG_STRIP is not set
# CONFIG_ATMEL is not set
# CONFIG_HOSTAP is not set
#
# Wan interfaces
......@@ -431,6 +475,8 @@ CONFIG_PPPOE=m
# CONFIG_SLIP is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
#
# ISDN subsystem
......@@ -459,19 +505,6 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set
#
# Input I/O drivers
#
# CONFIG_GAMEPORT is not set
CONFIG_SOUND_GAMEPORT=y
CONFIG_SERIO=y
CONFIG_SERIO_SERPORT=y
# CONFIG_SERIO_PARKBD is not set
CONFIG_SERIO_GSCPS2=y
CONFIG_HP_SDC=y
CONFIG_HIL_MLC=y
# CONFIG_SERIO_RAW is not set
#
# Input Device Drivers
#
......@@ -483,6 +516,7 @@ CONFIG_KEYBOARD_ATKBD_HP_KEYCODES=y
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_KEYBOARD_HIL_OLD=y
# CONFIG_KEYBOARD_HIL is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
......@@ -493,6 +527,19 @@ CONFIG_MOUSE_HIL=m
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
#
# Hardware I/O ports
#
CONFIG_SERIO=y
CONFIG_SERIO_SERPORT=y
# CONFIG_SERIO_PARKBD is not set
CONFIG_SERIO_GSCPS2=y
CONFIG_HP_SDC=y
CONFIG_HIL_MLC=y
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set
#
# Character devices
#
......@@ -511,7 +558,6 @@ CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
# CONFIG_SERIAL_8250_DETECT_IRQ is not set
# CONFIG_SERIAL_8250_MULTIPORT is not set
# CONFIG_SERIAL_8250_RSA is not set
#
......@@ -546,11 +592,13 @@ CONFIG_GEN_RTC_X=y
#
# Ftape, the floppy tape device driver
#
# CONFIG_AGP is not set
# CONFIG_DRM is not set
CONFIG_RAW_DRIVER=y
CONFIG_MAX_RAW_DEVS=256
#
# TPM devices
#
#
# I2C support
#
......@@ -561,10 +609,20 @@ CONFIG_MAX_RAW_DEVS=256
#
# CONFIG_W1 is not set
#
# Hardware Monitoring support
#
# CONFIG_HWMON is not set
# CONFIG_HWMON_VID is not set
#
# Misc devices
#
#
# Multimedia Capabilities Port drivers
#
#
# Multimedia devices
#
......@@ -579,28 +637,36 @@ CONFIG_MAX_RAW_DEVS=256
# Graphics support
#
CONFIG_FB=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
CONFIG_FB_SOFT_CURSOR=y
# CONFIG_FB_MACMODES is not set
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
CONFIG_FB_STI=y
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_VIRTUAL is not set
#
# Console display driver support
#
CONFIG_STI_CONSOLE=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_DUMMY_CONSOLE_COLUMNS=128
CONFIG_DUMMY_CONSOLE_ROWS=48
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_STI_CONSOLE=y
CONFIG_FONTS=y
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
# CONFIG_FONT_6x11 is not set
# CONFIG_FONT_7x14 is not set
# CONFIG_FONT_PEARL_8x8 is not set
# CONFIG_FONT_ACORN_8x8 is not set
# CONFIG_FONT_MINI_4x6 is not set
# CONFIG_FONT_SUN8x16 is not set
# CONFIG_FONT_SUN12x22 is not set
# CONFIG_FONT_10x18 is not set
#
# Logo configuration
......@@ -610,6 +676,7 @@ CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_VGA16 is not set
# CONFIG_LOGO_LINUX_CLUT224 is not set
CONFIG_LOGO_PARISC_CLUT224=y
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Sound
......@@ -656,10 +723,6 @@ CONFIG_SND_HARMONY=y
# CONFIG_USB_ARCH_HAS_HCD is not set
# CONFIG_USB_ARCH_HAS_OHCI is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information
#
#
# USB Gadget Support
#
......@@ -670,11 +733,21 @@ CONFIG_SND_HARMONY=y
#
# CONFIG_MMC is not set
#
# InfiniBand support
#
# CONFIG_INFINIBAND is not set
#
# SN Devices
#
#
# File systems
#
CONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
CONFIG_JBD=y
......@@ -682,20 +755,24 @@ CONFIG_JBD=y
# CONFIG_REISERFS_FS is not set
CONFIG_JFS_FS=m
# CONFIG_JFS_POSIX_ACL is not set
# CONFIG_JFS_SECURITY is not set
# CONFIG_JFS_DEBUG is not set
# CONFIG_JFS_STATISTICS is not set
CONFIG_FS_POSIX_ACL=y
CONFIG_XFS_FS=m
# CONFIG_XFS_RT is not set
CONFIG_XFS_EXPORT=y
# CONFIG_XFS_QUOTA is not set
# CONFIG_XFS_SECURITY is not set
# CONFIG_XFS_POSIX_ACL is not set
# CONFIG_XFS_RT is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=y
# CONFIG_FUSE_FS is not set
#
# CD-ROM/DVD Filesystems
......@@ -722,14 +799,11 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
# CONFIG_DEVFS_FS is not set
# CONFIG_DEVPTS_FS_XATTR is not set
CONFIG_TMPFS=y
CONFIG_TMPFS_XATTR=y
# CONFIG_TMPFS_SECURITY is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
# CONFIG_RELAYFS_FS is not set
#
# Miscellaneous filesystems
......@@ -754,16 +828,19 @@ CONFIG_UFS_FS=m
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
CONFIG_NFS_DIRECTIO=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
CONFIG_NFSD_V4=y
CONFIG_NFSD_TCP=y
CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
CONFIG_RPCSEC_GSS_KRB5=y
......@@ -778,6 +855,7 @@ CONFIG_CIFS=m
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
# CONFIG_9P_FS is not set
#
# Partition Types
......@@ -838,13 +916,19 @@ CONFIG_OPROFILE=m
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_LOG_BUF_SHIFT=16
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_IOREMAP is not set
# CONFIG_DEBUG_FS is not set
#
# Security options
......@@ -865,6 +949,7 @@ CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_WP512=m
CONFIG_CRYPTO_TGR192=m
CONFIG_CRYPTO_DES=y
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
......@@ -881,10 +966,15 @@ CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=m
CONFIG_CRYPTO_TEST=m
#
# Hardware crypto devices
#
#
# Library routines
#
CONFIG_CRC_CCITT=m
# CONFIG_CRC16 is not set
CONFIG_CRC32=y
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=m
......
此差异已折叠。
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.10-pa5
# Wed Jan 5 13:35:54 2005
# Linux kernel version: 2.6.14-rc5-pa1
# Fri Oct 21 23:06:10 2005
#
CONFIG_PARISC=y
CONFIG_MMU=y
CONFIG_STACK_GROWSUP=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
#
# Code maturity level options
......@@ -14,33 +17,39 @@ CONFIG_RWSEM_GENERIC_SPINLOCK=y
# CONFIG_EXPERIMENTAL is not set
CONFIG_CLEAN_COMPILE=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
#
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
CONFIG_LOG_BUF_SHIFT=16
# CONFIG_HOTPLUG is not set
CONFIG_KOBJECT_UEVENT=y
# CONFIG_IKCONFIG is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
#
# Loadable module support
......@@ -60,8 +69,14 @@ CONFIG_PA7100LC=y
# CONFIG_PA7300LC is not set
# CONFIG_PA8X00 is not set
CONFIG_PA11=y
# CONFIG_64BIT is not set
# CONFIG_SMP is not set
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
# CONFIG_PREEMPT is not set
# CONFIG_HPUX is not set
......@@ -78,11 +93,25 @@ CONFIG_EISA_NAMES=y
CONFIG_ISA=y
CONFIG_PCI=y
CONFIG_PCI_LEGACY_PROC=y
CONFIG_PCI_NAMES=y
# CONFIG_PCI_DEBUG is not set
CONFIG_GSC_DINO=y
# CONFIG_PCI_LBA is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
#
# PCI Hotplug Support
#
#
# PA-RISC specific drivers
#
CONFIG_CHASSIS_LCD_LED=y
# CONFIG_PDC_CHASSIS is not set
CONFIG_PDC_STABLE=y
#
# Executable file formats
......@@ -90,6 +119,64 @@ CONFIG_CHASSIS_LCD_LED=y
CONFIG_BINFMT_ELF=y
# CONFIG_BINFMT_MISC is not set
#
# Networking
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_PNP=y
# CONFIG_IP_PNP_DHCP is not set
CONFIG_IP_PNP_BOOTP=y
# CONFIG_IP_PNP_RARP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_BIC=y
CONFIG_IPV6=y
# CONFIG_IPV6_PRIVACY is not set
# CONFIG_INET6_AH is not set
# CONFIG_INET6_ESP is not set
# CONFIG_INET6_IPCOMP is not set
# CONFIG_INET6_TUNNEL is not set
# CONFIG_IPV6_TUNNEL is not set
# CONFIG_NETFILTER is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_NET_SCHED is not set
# CONFIG_NET_CLS_ROUTE is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_IEEE80211 is not set
#
# Device Drivers
#
......@@ -99,8 +186,14 @@ CONFIG_BINFMT_ELF=y
#
CONFIG_STANDALONE=y
# CONFIG_PREVENT_FIRMWARE_BUILD is not set
# CONFIG_FW_LOADER is not set
# CONFIG_DEBUG_DRIVER is not set
#
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
#
# Memory Technology Devices (MTD)
#
......@@ -111,10 +204,8 @@ CONFIG_STANDALONE=y
#
CONFIG_PARPORT=y
CONFIG_PARPORT_PC=y
CONFIG_PARPORT_PC_CML1=y
# CONFIG_PARPORT_SERIAL is not set
CONFIG_PARPORT_GSC=y
# CONFIG_PARPORT_OTHER is not set
# CONFIG_PARPORT_1284 is not set
#
......@@ -125,19 +216,17 @@ CONFIG_PARPORT_GSC=y
#
# Block devices
#
# CONFIG_BLK_DEV_FD is not set
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=y
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_RAM is not set
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CDROM_PKTCDVD=m
CONFIG_CDROM_PKTCDVD_BUFFERS=8
# CONFIG_CDROM_PKTCDVD_WCACHE is not set
......@@ -149,6 +238,7 @@ CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
CONFIG_ATA_OVER_ETH=y
#
# ATA/ATAPI/MFM/RLL support
......@@ -158,6 +248,7 @@ CONFIG_IOSCHED_CFQ=y
#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y
......@@ -170,6 +261,7 @@ CONFIG_CHR_DEV_ST=y
CONFIG_BLK_DEV_SR=y
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=y
# CONFIG_CHR_DEV_SCH is not set
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
......@@ -183,16 +275,16 @@ CONFIG_CHR_DEV_SG=y
#
CONFIG_SCSI_SPI_ATTRS=y
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
......@@ -202,14 +294,11 @@ CONFIG_SCSI_SPI_ATTRS=y
# CONFIG_SCSI_IN2000 is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
# CONFIG_SCSI_SATA is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set
# CONFIG_SCSI_IPS is not set
......@@ -219,7 +308,6 @@ CONFIG_SCSI_SPI_ATTRS=y
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C406A is not set
CONFIG_SCSI_LASI700=y
CONFIG_53C700_MEM_MAPPED=y
CONFIG_53C700_LE_ON_BE=y
CONFIG_SCSI_SYM53C8XX_2=y
CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=0
......@@ -231,7 +319,6 @@ CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
CONFIG_SCSI_QLA2XXX=y
......@@ -240,12 +327,12 @@ CONFIG_SCSI_QLA2XXX=y
# CONFIG_SCSI_QLA2300 is not set
# CONFIG_SCSI_QLA2322 is not set
# CONFIG_SCSI_QLA6312 is not set
# CONFIG_SCSI_QLA6322 is not set
# CONFIG_SCSI_QLA24XX is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_SIM710 is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
......@@ -263,6 +350,7 @@ CONFIG_MD_LINEAR=y
CONFIG_MD_RAID0=y
CONFIG_MD_RAID1=y
CONFIG_MD_RAID5=y
CONFIG_MD_RAID6=y
# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
# CONFIG_BLK_DEV_DM is not set
......@@ -271,6 +359,9 @@ CONFIG_MD_RAID5=y
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_SPI is not set
# CONFIG_FUSION_FC is not set
# CONFIG_FUSION_SAS is not set
#
# IEEE 1394 (FireWire) support
......@@ -283,58 +374,8 @@ CONFIG_MD_RAID5=y
# CONFIG_I2O is not set
#
# Networking support
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_NETLINK_DEV=y
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_PNP=y
# CONFIG_IP_PNP_DHCP is not set
CONFIG_IP_PNP_BOOTP=y
# CONFIG_IP_PNP_RARP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_IP_TCPDIAG=y
# CONFIG_IP_TCPDIAG_IPV6 is not set
# CONFIG_NETFILTER is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
# CONFIG_NET_CLS_ROUTE is not set
#
# Network testing
# Network device support
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
......@@ -346,6 +387,11 @@ CONFIG_NETDEVICES=y
#
# CONFIG_ARCNET is not set
#
# PHY device support
#
# CONFIG_PHYLIB is not set
#
# Ethernet (10 or 100Mbit)
#
......@@ -354,8 +400,8 @@ CONFIG_NET_ETHERNET=y
# CONFIG_LASI_82596 is not set
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
......@@ -369,6 +415,7 @@ CONFIG_TULIP=y
# CONFIG_DE4X5 is not set
# CONFIG_WINBOND_840 is not set
# CONFIG_DM9102 is not set
# CONFIG_ULI526X is not set
# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
# CONFIG_NET_ISA is not set
......@@ -384,12 +431,15 @@ CONFIG_TULIP=y
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
#
# Ethernet (10000 Mbit)
#
# CONFIG_CHELSIO_T1 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
......@@ -413,12 +463,12 @@ CONFIG_NET_RADIO=y
#
# Wireless 802.11b ISA/PCI cards support
#
# CONFIG_AIRO is not set
# CONFIG_HERMES is not set
#
# Prism GT/Duette 802.11(a/b/g) PCI/Cardbus support
#
# CONFIG_HOSTAP is not set
CONFIG_NET_WIRELESS=y
#
......@@ -435,6 +485,8 @@ CONFIG_PPP=y
# CONFIG_PPP_BSDCOMP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
#
# ISDN subsystem
......@@ -463,24 +515,13 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set
#
# Input I/O drivers
#
# CONFIG_GAMEPORT is not set
CONFIG_SOUND_GAMEPORT=y
CONFIG_SERIO=y
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_PARKBD is not set
CONFIG_SERIO_GSCPS2=y
# CONFIG_HP_SDC is not set
# CONFIG_SERIO_PCIPS2 is not set
# CONFIG_SERIO_RAW is not set
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
# CONFIG_KEYBOARD_ATKBD is not set
CONFIG_KEYBOARD_ATKBD=y
CONFIG_KEYBOARD_ATKBD_HP_KEYCODES=y
# CONFIG_KEYBOARD_ATKBD_RDI_KEYCODES is not set
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
......@@ -488,7 +529,7 @@ CONFIG_INPUT_KEYBOARD=y
# CONFIG_KEYBOARD_HIL_OLD is not set
# CONFIG_KEYBOARD_HIL is not set
CONFIG_INPUT_MOUSE=y
# CONFIG_MOUSE_PS2 is not set
CONFIG_MOUSE_PS2=y
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_INPORT is not set
# CONFIG_MOUSE_LOGIBM is not set
......@@ -501,6 +542,19 @@ CONFIG_INPUT_MISC=y
# CONFIG_INPUT_UINPUT is not set
# CONFIG_HP_SDC_RTC is not set
#
# Hardware I/O ports
#
CONFIG_SERIO=y
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_PARKBD is not set
CONFIG_SERIO_GSCPS2=y
# CONFIG_HP_SDC is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set
#
# Character devices
#
......@@ -519,8 +573,11 @@ CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
# CONFIG_SERIAL_8250_DETECT_IRQ is not set
# CONFIG_SERIAL_8250_MULTIPORT is not set
# CONFIG_SERIAL_8250_RSA is not set
# CONFIG_SERIAL_8250_FOURPORT is not set
# CONFIG_SERIAL_8250_ACCENT is not set
# CONFIG_SERIAL_8250_BOCA is not set
# CONFIG_SERIAL_8250_HUB6 is not set
#
# Non-8250 serial port support
......@@ -529,6 +586,7 @@ CONFIG_SERIAL_8250_SHARE_IRQ=y
# CONFIG_PDC_CONSOLE is not set
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
......@@ -555,10 +613,13 @@ CONFIG_GEN_RTC=y
#
# Ftape, the floppy tape device driver
#
# CONFIG_AGP is not set
# CONFIG_DRM is not set
# CONFIG_RAW_DRIVER is not set
#
# TPM devices
#
#
# I2C support
#
......@@ -569,10 +630,20 @@ CONFIG_GEN_RTC=y
#
# CONFIG_W1 is not set
#
# Hardware Monitoring support
#
# CONFIG_HWMON is not set
# CONFIG_HWMON_VID is not set
#
# Misc devices
#
#
# Multimedia Capabilities Port drivers
#
#
# Multimedia devices
#
......@@ -587,6 +658,11 @@ CONFIG_GEN_RTC=y
# Graphics support
#
CONFIG_FB=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
CONFIG_FB_SOFT_CURSOR=y
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_MODE_HELPERS is not set
# CONFIG_FB_TILEBLITTING is not set
# CONFIG_FB_CIRRUS is not set
......@@ -595,6 +671,7 @@ CONFIG_FB=y
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
CONFIG_FB_STI=y
# CONFIG_FB_NVIDIA is not set
# CONFIG_FB_RIVA is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON_OLD is not set
......@@ -606,18 +683,19 @@ CONFIG_FB_STI=y
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_CYBLA is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_VIRTUAL is not set
#
# Console display driver support
#
# CONFIG_MDA_CONSOLE is not set
CONFIG_STI_CONSOLE=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_DUMMY_CONSOLE_COLUMNS=160
CONFIG_DUMMY_CONSOLE_ROWS=64
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_STI_CONSOLE=y
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
......@@ -630,6 +708,7 @@ CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
CONFIG_LOGO_PARISC_CLUT224=y
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Sound
......@@ -639,13 +718,9 @@ CONFIG_LOGO_PARISC_CLUT224=y
#
# USB support
#
# CONFIG_USB is not set
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information
#
# CONFIG_USB is not set
#
# USB Gadget Support
......@@ -657,24 +732,37 @@ CONFIG_USB_ARCH_HAS_OHCI=y
#
# CONFIG_MMC is not set
#
# InfiniBand support
#
# CONFIG_INFINIBAND is not set
#
# SN Devices
#
#
# File systems
#
CONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=y
# CONFIG_FUSE_FS is not set
#
# CD-ROM/DVD Filesystems
......@@ -697,11 +785,10 @@ CONFIG_JOLIET=y
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
# CONFIG_DEVPTS_FS_XATTR is not set
CONFIG_TMPFS=y
# CONFIG_TMPFS_XATTR is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
# CONFIG_RELAYFS_FS is not set
#
# Miscellaneous filesystems
......@@ -719,15 +806,19 @@ CONFIG_RAMFS=y
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFSD=y
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
CONFIG_NFSD_TCP=y
CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
# CONFIG_SMB_FS is not set
CONFIG_SMB_FS=y
# CONFIG_SMB_NLS_DEFAULT is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
......@@ -785,13 +876,19 @@ CONFIG_NLS_DEFAULT="iso8859-1"
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_LOG_BUF_SHIFT=16
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_IOREMAP is not set
# CONFIG_DEBUG_FS is not set
#
# Security options
......@@ -815,6 +912,7 @@ CONFIG_CRYPTO=y
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_TGR192 is not set
# CONFIG_CRYPTO_DES is not set
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_TWOFISH is not set
......@@ -831,9 +929,14 @@ CONFIG_CRYPTO=y
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_TEST is not set
#
# Hardware crypto devices
#
#
# Library routines
#
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
此差异已折叠。
此差异已折叠。
......@@ -27,6 +27,7 @@
#include <asm/page.h>
#include <asm/pgalloc.h>
#include <asm/processor.h>
#include <asm/sections.h>
int split_tlb;
int dcache_stride;
......@@ -207,6 +208,9 @@ parisc_cache_init(void)
/* "New and Improved" version from Jim Hull
* (1 << (cc_block-1)) * (cc_line << (4 + cnf.cc_shift))
* The following CAFL_STRIDE is an optimized version, see
* http://lists.parisc-linux.org/pipermail/parisc-linux/2004-June/023625.html
* http://lists.parisc-linux.org/pipermail/parisc-linux/2004-June/023671.html
*/
#define CAFL_STRIDE(cnf) (cnf.cc_line << (3 + cnf.cc_block + cnf.cc_shift))
dcache_stride = CAFL_STRIDE(cache_info.dc_conf);
......@@ -339,17 +343,15 @@ int parisc_cache_flush_threshold = FLUSH_THRESHOLD;
void parisc_setup_cache_timing(void)
{
unsigned long rangetime, alltime;
extern char _text; /* start of kernel code, defined by linker */
extern char _end; /* end of BSS, defined by linker */
unsigned long size;
alltime = mfctl(16);
flush_data_cache();
alltime = mfctl(16) - alltime;
size = (unsigned long)(&_end - _text);
size = (unsigned long)(_end - _text);
rangetime = mfctl(16);
flush_kernel_dcache_range((unsigned long)&_text, size);
flush_kernel_dcache_range((unsigned long)_text, size);
rangetime = mfctl(16) - rangetime;
printk(KERN_DEBUG "Whole cache flush %lu cycles, flushing %lu bytes %lu cycles\n",
......
此差异已折叠。
此差异已折叠。
......@@ -83,15 +83,15 @@ static unsigned long pdc_result2[32] __attribute__ ((aligned (8)));
int parisc_narrow_firmware = 1;
#endif
/* on all currently-supported platforms, IODC I/O calls are always
* 32-bit calls, and MEM_PDC calls are always the same width as the OS.
* This means Cxxx boxes can't run wide kernels right now. -PB
/* On most currently-supported platforms, IODC I/O calls are 32-bit calls
* and MEM_PDC calls are always the same width as the OS.
* Some PAT boxes may have 64-bit IODC I/O.
*
* CONFIG_PDC_NARROW has been added to allow 64-bit kernels to run on
* systems with 32-bit MEM_PDC calls. This will allow wide kernels to
* run on Cxxx boxes now. -RB
*
* Note that some PAT boxes may have 64-bit IODC I/O...
* Ryan Bradetich added the now obsolete CONFIG_PDC_NARROW to allow
* 64-bit kernels to run on systems with 32-bit MEM_PDC calls.
* This allowed wide kernels to run on Cxxx boxes.
* We now detect 32-bit-only PDC and dynamically switch to 32-bit mode
* when running a 64-bit kernel on such boxes (e.g. C200 or C360).
*/
#ifdef __LP64__
......
此差异已折叠。
......@@ -104,11 +104,8 @@ static int drm32_version(unsigned int fd, unsigned int cmd, unsigned long arg)
}
out:
if (kversion.name)
kfree(kversion.name);
if (kversion.date)
kfree(kversion.date);
if (kversion.desc)
kfree(kversion.desc);
return ret;
}
......@@ -166,9 +163,7 @@ static int drm32_getsetunique(unsigned int fd, unsigned int cmd, unsigned long a
ret = -EFAULT;
}
if (karg.unique != NULL)
kfree(karg.unique);
return ret;
}
......@@ -265,7 +260,6 @@ static int drm32_info_bufs(unsigned int fd, unsigned int cmd, unsigned long arg)
}
kfree(karg.list);
return ret;
}
......@@ -305,7 +299,6 @@ static int drm32_free_bufs(unsigned int fd, unsigned int cmd, unsigned long arg)
out:
kfree(karg.list);
return ret;
}
......@@ -494,15 +487,10 @@ static int drm32_dma(unsigned int fd, unsigned int cmd, unsigned long arg)
}
out:
if (karg.send_indices)
kfree(karg.send_indices);
if (karg.send_sizes)
kfree(karg.send_sizes);
if (karg.request_indices)
kfree(karg.request_indices);
if (karg.request_sizes)
kfree(karg.request_sizes);
return ret;
}
......@@ -555,9 +543,7 @@ static int drm32_res_ctx(unsigned int fd, unsigned int cmd, unsigned long arg)
ret = -EFAULT;
}
if (karg.contexts)
kfree(karg.contexts);
return ret;
}
......
此差异已折叠。
......@@ -31,7 +31,7 @@
#include <asm/page.h> /* get_order */
#include <asm/pgalloc.h>
#include <asm/uaccess.h>
#include <asm/tlbflush.h> /* for purge_tlb_*() macros */
static struct proc_dir_entry * proc_gsc_root = NULL;
static int pcxl_proc_info(char *buffer, char **start, off_t offset, int length);
......@@ -343,7 +343,17 @@ pcxl_dma_init(void)
get_order(pcxl_res_size));
memset(pcxl_res_map, 0, pcxl_res_size);
proc_gsc_root = proc_mkdir("gsc", 0);
create_proc_info_entry("dino", 0, proc_gsc_root, pcxl_proc_info);
if (!proc_gsc_root)
printk(KERN_WARNING
"pcxl_dma_init: Unable to create gsc /proc dir entry\n");
else {
struct proc_dir_entry* ent;
ent = create_proc_info_entry("pcxl_dma", 0,
proc_gsc_root, pcxl_proc_info);
if (!ent)
printk(KERN_WARNING
"pci-dma.c: Unable to create pcxl_dma /proc entry.\n");
}
return 0;
}
......@@ -545,16 +555,16 @@ struct hppa_dma_ops pcx_dma_ops = {
static int pcxl_proc_info(char *buf, char **start, off_t offset, int len)
{
#if 0
u_long i = 0;
unsigned long *res_ptr = (u_long *)pcxl_res_map;
#endif
unsigned long total_pages = pcxl_res_size << 3; /* 8 bits per byte */
sprintf(buf, "\nDMA Mapping Area size : %d bytes (%d pages)\n",
PCXL_DMA_MAP_SIZE,
(pcxl_res_size << 3) ); /* 1 bit per page */
sprintf(buf, "\nDMA Mapping Area size : %d bytes (%ld pages)\n",
PCXL_DMA_MAP_SIZE, total_pages);
sprintf(buf, "%sResource bitmap : %d bytes (%d pages)\n",
buf, pcxl_res_size, pcxl_res_size << 3); /* 8 bits per byte */
sprintf(buf, "%sResource bitmap : %d bytes\n", buf, pcxl_res_size);
strcat(buf, " total: free: used: % used:\n");
sprintf(buf, "%sblocks %8d %8ld %8ld %8ld%%\n", buf, pcxl_res_size,
......@@ -565,6 +575,7 @@ static int pcxl_proc_info(char *buf, char **start, off_t offset, int len)
total_pages - pcxl_used_pages, pcxl_used_pages,
(pcxl_used_pages * 100 / total_pages));
#if 0
strcat(buf, "\nResource bitmap:");
for(; i < (pcxl_res_size / sizeof(u_long)); ++i, ++res_ptr) {
......@@ -572,6 +583,7 @@ static int pcxl_proc_info(char *buf, char **start, off_t offset, int len)
strcat(buf,"\n ");
sprintf(buf, "%s %08lx", buf, *res_ptr);
}
#endif
strcat(buf, "\n");
return strlen(buf);
}
......
......@@ -202,7 +202,8 @@ static void
pcibios_link_hba_resources( struct resource *hba_res, struct resource *r)
{
if (!r->parent) {
printk(KERN_EMERG "PCI: Tell willy he's wrong\n");
printk(KERN_EMERG "PCI: resource not parented! [%lx-%lx]\n",
r->start, r->end);
r->parent = hba_res;
/* reverse link is harder *sigh* */
......
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
......@@ -18,7 +18,7 @@
*/
#undef ENTRY_SYS_CPUS /* syscall support for iCOD-like functionality */
#include <linux/autoconf.h>
#include <linux/config.h>
#include <linux/types.h>
#include <linux/spinlock.h>
......
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册