From 8a64c0f6b7ec7f758c4ef445e49f479e27fa2236 Mon Sep 17 00:00:00 2001 From: Daniel Mack Date: Tue, 6 Apr 2010 10:52:44 +0200 Subject: [PATCH] libertas/sdio: 8686: set ECSI bit for 1-bit transfers When operating in 1-bit mode, SDAT1 is used as dedicated interrupt line. However, the 8686 will only drive this line when the ECSI bit is set in the CCCR_IF register. Thanks to Alagu Sankar for pointing me in the right direction. Signed-off-by: Daniel Mack Cc: Alagu Sankar Cc: Volker Ernst Cc: Dan Williams Cc: John W. Linville Cc: Holger Schurig Cc: Bing Zhao Cc: libertas-dev@lists.infradead.org Cc: linux-wireless@vger.kernel.org Cc: linux-mmc@vger.kernel.org Acked-by: Dan Williams Signed-off-by: John W. Linville --- drivers/net/wireless/libertas/if_sdio.c | 22 ++++++++++++++++++++++ include/linux/mmc/sdio.h | 2 ++ 2 files changed, 24 insertions(+) diff --git a/drivers/net/wireless/libertas/if_sdio.c b/drivers/net/wireless/libertas/if_sdio.c index 7a73f625273b..33206a98a572 100644 --- a/drivers/net/wireless/libertas/if_sdio.c +++ b/drivers/net/wireless/libertas/if_sdio.c @@ -34,6 +34,8 @@ #include #include #include +#include +#include #include "host.h" #include "decl.h" @@ -942,6 +944,7 @@ static int if_sdio_probe(struct sdio_func *func, int ret, i; unsigned int model; struct if_sdio_packet *packet; + struct mmc_host *host = func->card->host; lbs_deb_enter(LBS_DEB_SDIO); @@ -1022,6 +1025,25 @@ static int if_sdio_probe(struct sdio_func *func, if (ret) goto disable; + /* For 1-bit transfers to the 8686 model, we need to enable the + * interrupt flag in the CCCR register. Set the MMC_QUIRK_LENIENT_FN0 + * bit to allow access to non-vendor registers. */ + if ((card->model == IF_SDIO_MODEL_8686) && + (host->caps & MMC_CAP_SDIO_IRQ) && + (host->ios.bus_width == MMC_BUS_WIDTH_1)) { + u8 reg; + + func->card->quirks |= MMC_QUIRK_LENIENT_FN0; + reg = sdio_f0_readb(func, SDIO_CCCR_IF, &ret); + if (ret) + goto release_int; + + reg |= SDIO_BUS_ECSI; + sdio_f0_writeb(func, reg, SDIO_CCCR_IF, &ret); + if (ret) + goto release_int; + } + card->ioport = sdio_readb(func, IF_SDIO_IOPORT, &ret); if (ret) goto release_int; diff --git a/include/linux/mmc/sdio.h b/include/linux/mmc/sdio.h index 47ba464f5170..118f0295a575 100644 --- a/include/linux/mmc/sdio.h +++ b/include/linux/mmc/sdio.h @@ -94,6 +94,8 @@ #define SDIO_BUS_WIDTH_1BIT 0x00 #define SDIO_BUS_WIDTH_4BIT 0x02 +#define SDIO_BUS_ECSI 0x20 /* Enable continuous SPI interrupt */ +#define SDIO_BUS_SCSI 0x40 /* Support continuous SPI interrupt */ #define SDIO_BUS_CD_DISABLE 0x80 /* disable pull-up on DAT3 (pin 1) */ -- GitLab